| /* |
| * Broadcom BCM570x Ethernet Driver for U-Boot. |
| * Support 5701, 5702, 5703, and 5704. Single instance driver. |
| * Copyright (C) 2002 James F. Dougherty (jfd@broadcom.com) |
| */ |
| |
| #include <common.h> |
| |
| #ifdef CONFIG_BMW |
| #include <mpc824x.h> |
| #endif |
| #include <net.h> |
| #include "bcm570x_mm.h" |
| #include "bcm570x_autoneg.h" |
| #include <pci.h> |
| #include <malloc.h> |
| |
| /* |
| * PCI Registers and definitions. |
| */ |
| #define PCI_CMD_MASK 0xffff0000 /* mask to save status bits */ |
| #define PCI_ANY_ID (~0) |
| |
| /* |
| * PCI memory base for Ethernet device as well as device Interrupt. |
| */ |
| #define BCM570X_MBAR 0x80100000 |
| #define BCM570X_ILINE 1 |
| |
| #define SECOND_USEC 1000000 |
| #define MAX_PACKET_SIZE 1600 |
| #define MAX_UNITS 4 |
| |
| /* Globals to this module */ |
| int initialized = 0; |
| unsigned int ioBase = 0; |
| volatile PLM_DEVICE_BLOCK pDevice = NULL; /* 570x softc */ |
| volatile PUM_DEVICE_BLOCK pUmDevice = NULL; |
| |
| /* Used to pass the full-duplex flag, etc. */ |
| int line_speed[MAX_UNITS] = { 0, 0, 0, 0 }; |
| static int full_duplex[MAX_UNITS] = { 1, 1, 1, 1 }; |
| static int rx_flow_control[MAX_UNITS] = { 0, 0, 0, 0 }; |
| static int tx_flow_control[MAX_UNITS] = { 0, 0, 0, 0 }; |
| static int auto_flow_control[MAX_UNITS] = { 0, 0, 0, 0 }; |
| static int tx_checksum[MAX_UNITS] = { 1, 1, 1, 1 }; |
| static int rx_checksum[MAX_UNITS] = { 1, 1, 1, 1 }; |
| static int auto_speed[MAX_UNITS] = { 1, 1, 1, 1 }; |
| |
| #if JUMBO_FRAMES |
| /* Jumbo MTU for interfaces. */ |
| static int mtu[MAX_UNITS] = { 0, 0, 0, 0 }; |
| #endif |
| |
| /* Turn on Wake-on lan for a device unit */ |
| static int enable_wol[MAX_UNITS] = { 0, 0, 0, 0 }; |
| |
| #define TX_DESC_CNT DEFAULT_TX_PACKET_DESC_COUNT |
| static unsigned int tx_pkt_desc_cnt[MAX_UNITS] = |
| { TX_DESC_CNT, TX_DESC_CNT, TX_DESC_CNT, TX_DESC_CNT }; |
| |
| #define RX_DESC_CNT DEFAULT_STD_RCV_DESC_COUNT |
| static unsigned int rx_std_desc_cnt[MAX_UNITS] = |
| { RX_DESC_CNT, RX_DESC_CNT, RX_DESC_CNT, RX_DESC_CNT }; |
| |
| static unsigned int rx_adaptive_coalesce[MAX_UNITS] = { 1, 1, 1, 1 }; |
| |
| #if T3_JUMBO_RCV_RCB_ENTRY_COUNT |
| #define JBO_DESC_CNT DEFAULT_JUMBO_RCV_DESC_COUNT |
| static unsigned int rx_jumbo_desc_cnt[MAX_UNITS] = |
| { JBO_DESC_CNT, JBO_DESC_CNT, JBO_DESC_CNT, JBO_DESC_CNT }; |
| #endif |
| #define RX_COAL_TK DEFAULT_RX_COALESCING_TICKS |
| static unsigned int rx_coalesce_ticks[MAX_UNITS] = |
| { RX_COAL_TK, RX_COAL_TK, RX_COAL_TK, RX_COAL_TK }; |
| |
| #define RX_COAL_FM DEFAULT_RX_MAX_COALESCED_FRAMES |
| static unsigned int rx_max_coalesce_frames[MAX_UNITS] = |
| { RX_COAL_FM, RX_COAL_FM, RX_COAL_FM, RX_COAL_FM }; |
| |
| #define TX_COAL_TK DEFAULT_TX_COALESCING_TICKS |
| static unsigned int tx_coalesce_ticks[MAX_UNITS] = |
| { TX_COAL_TK, TX_COAL_TK, TX_COAL_TK, TX_COAL_TK }; |
| |
| #define TX_COAL_FM DEFAULT_TX_MAX_COALESCED_FRAMES |
| static unsigned int tx_max_coalesce_frames[MAX_UNITS] = |
| { TX_COAL_FM, TX_COAL_FM, TX_COAL_FM, TX_COAL_FM }; |
| |
| #define ST_COAL_TK DEFAULT_STATS_COALESCING_TICKS |
| static unsigned int stats_coalesce_ticks[MAX_UNITS] = |
| { ST_COAL_TK, ST_COAL_TK, ST_COAL_TK, ST_COAL_TK }; |
| |
| /* |
| * Legitimate values for BCM570x device types |
| */ |
| typedef enum { |
| BCM5700VIGIL = 0, |
| BCM5700A6, |
| BCM5700T6, |
| BCM5700A9, |
| BCM5700T9, |
| BCM5700, |
| BCM5701A5, |
| BCM5701T1, |
| BCM5701T8, |
| BCM5701A7, |
| BCM5701A10, |
| BCM5701A12, |
| BCM5701, |
| BCM5702, |
| BCM5703, |
| BCM5703A31, |
| TC996T, |
| TC996ST, |
| TC996SSX, |
| TC996SX, |
| TC996BT, |
| TC997T, |
| TC997SX, |
| TC1000T, |
| TC940BR01, |
| TC942BR01, |
| NC6770, |
| NC7760, |
| NC7770, |
| NC7780 |
| } board_t; |
| |
| /* Chip-Rev names for each device-type */ |
| static struct { |
| char *name; |
| } chip_rev[] = { |
| { |
| "BCM5700VIGIL"}, { |
| "BCM5700A6"}, { |
| "BCM5700T6"}, { |
| "BCM5700A9"}, { |
| "BCM5700T9"}, { |
| "BCM5700"}, { |
| "BCM5701A5"}, { |
| "BCM5701T1"}, { |
| "BCM5701T8"}, { |
| "BCM5701A7"}, { |
| "BCM5701A10"}, { |
| "BCM5701A12"}, { |
| "BCM5701"}, { |
| "BCM5702"}, { |
| "BCM5703"}, { |
| "BCM5703A31"}, { |
| "TC996T"}, { |
| "TC996ST"}, { |
| "TC996SSX"}, { |
| "TC996SX"}, { |
| "TC996BT"}, { |
| "TC997T"}, { |
| "TC997SX"}, { |
| "TC1000T"}, { |
| "TC940BR01"}, { |
| "TC942BR01"}, { |
| "NC6770"}, { |
| "NC7760"}, { |
| "NC7770"}, { |
| "NC7780"}, { |
| 0} |
| }; |
| |
| /* indexed by board_t, above */ |
| static struct { |
| char *name; |
| } board_info[] = { |
| { |
| "Broadcom Vigil B5700 1000Base-T"}, { |
| "Broadcom BCM5700 1000Base-T"}, { |
| "Broadcom BCM5700 1000Base-SX"}, { |
| "Broadcom BCM5700 1000Base-SX"}, { |
| "Broadcom BCM5700 1000Base-T"}, { |
| "Broadcom BCM5700"}, { |
| "Broadcom BCM5701 1000Base-T"}, { |
| "Broadcom BCM5701 1000Base-T"}, { |
| "Broadcom BCM5701 1000Base-T"}, { |
| "Broadcom BCM5701 1000Base-SX"}, { |
| "Broadcom BCM5701 1000Base-T"}, { |
| "Broadcom BCM5701 1000Base-T"}, { |
| "Broadcom BCM5701"}, { |
| "Broadcom BCM5702 1000Base-T"}, { |
| "Broadcom BCM5703 1000Base-T"}, { |
| "Broadcom BCM5703 1000Base-SX"}, { |
| "3Com 3C996 10/100/1000 Server NIC"}, { |
| "3Com 3C996 10/100/1000 Server NIC"}, { |
| "3Com 3C996 Gigabit Fiber-SX Server NIC"}, { |
| "3Com 3C996 Gigabit Fiber-SX Server NIC"}, { |
| "3Com 3C996B Gigabit Server NIC"}, { |
| "3Com 3C997 Gigabit Server NIC"}, { |
| "3Com 3C997 Gigabit Fiber-SX Server NIC"}, { |
| "3Com 3C1000 Gigabit NIC"}, { |
| "3Com 3C940 Gigabit LOM (21X21)"}, { |
| "3Com 3C942 Gigabit LOM (31X31)"}, { |
| "Compaq NC6770 Gigabit Server Adapter"}, { |
| "Compaq NC7760 Gigabit Server Adapter"}, { |
| "Compaq NC7770 Gigabit Server Adapter"}, { |
| "Compaq NC7780 Gigabit Server Adapter"}, { |
| 0},}; |
| |
| /* PCI Devices which use the 570x chipset */ |
| struct pci_device_table { |
| unsigned short vendor_id, device_id; /* Vendor/DeviceID */ |
| unsigned short subvendor, subdevice; /* Subsystem ID's or PCI_ANY_ID */ |
| unsigned int class, class_mask; /* (class,subclass,prog-if) triplet */ |
| unsigned long board_id; /* Data private to the driver */ |
| int io_size, min_latency; |
| } bcm570xDevices[] = { |
| { |
| 0x14e4, 0x1644, 0x1014, 0x0277, 0, 0, BCM5700VIGIL, 128, 32}, { |
| 0x14e4, 0x1644, 0x14e4, 0x1644, 0, 0, BCM5700A6, 128, 32}, { |
| 0x14e4, 0x1644, 0x14e4, 0x2, 0, 0, BCM5700T6, 128, 32}, { |
| 0x14e4, 0x1644, 0x14e4, 0x3, 0, 0, BCM5700A9, 128, 32}, { |
| 0x14e4, 0x1644, 0x14e4, 0x4, 0, 0, BCM5700T9, 128, 32}, { |
| 0x14e4, 0x1644, 0x1028, 0xd1, 0, 0, BCM5700, 128, 32}, { |
| 0x14e4, 0x1644, 0x1028, 0x0106, 0, 0, BCM5700, 128, 32}, { |
| 0x14e4, 0x1644, 0x1028, 0x0109, 0, 0, BCM5700, 128, 32}, { |
| 0x14e4, 0x1644, 0x1028, 0x010a, 0, 0, BCM5700, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1000, 0, 0, TC996T, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1001, 0, 0, TC996ST, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1002, 0, 0, TC996SSX, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1003, 0, 0, TC997T, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1005, 0, 0, TC997SX, 128, 32}, { |
| 0x14e4, 0x1644, 0x10b7, 0x1008, 0, 0, TC942BR01, 128, 32}, { |
| 0x14e4, 0x1644, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5700, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 1, 0, 0, BCM5701A5, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 5, 0, 0, BCM5701T1, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 6, 0, 0, BCM5701T8, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 7, 0, 0, BCM5701A7, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 8, 0, 0, BCM5701A10, 128, 32}, { |
| 0x14e4, 0x1645, 0x14e4, 0x8008, 0, 0, BCM5701A12, 128, 32}, { |
| 0x14e4, 0x1645, 0x0e11, 0xc1, 0, 0, NC6770, 128, 32}, { |
| 0x14e4, 0x1645, 0x0e11, 0x7c, 0, 0, NC7770, 128, 32}, { |
| 0x14e4, 0x1645, 0x0e11, 0x85, 0, 0, NC7780, 128, 32}, { |
| 0x14e4, 0x1645, 0x1028, 0x0121, 0, 0, BCM5701, 128, 32}, { |
| 0x14e4, 0x1645, 0x10b7, 0x1004, 0, 0, TC996SX, 128, 32}, { |
| 0x14e4, 0x1645, 0x10b7, 0x1006, 0, 0, TC996BT, 128, 32}, { |
| 0x14e4, 0x1645, 0x10b7, 0x1007, 0, 0, TC1000T, 128, 32}, { |
| 0x14e4, 0x1645, 0x10b7, 0x1008, 0, 0, TC940BR01, 128, 32}, { |
| 0x14e4, 0x1645, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5701, 128, 32}, { |
| 0x14e4, 0x1646, 0x14e4, 0x8009, 0, 0, BCM5702, 128, 32}, { |
| 0x14e4, 0x1646, 0x0e11, 0xbb, 0, 0, NC7760, 128, 32}, { |
| 0x14e4, 0x1646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5702, 128, 32}, { |
| 0x14e4, 0x16a6, 0x14e4, 0x8009, 0, 0, BCM5702, 128, 32}, { |
| 0x14e4, 0x16a6, 0x0e11, 0xbb, 0, 0, NC7760, 128, 32}, { |
| 0x14e4, 0x16a6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5702, 128, 32}, { |
| 0x14e4, 0x1647, 0x14e4, 0x0009, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x1647, 0x14e4, 0x000a, 0, 0, BCM5703A31, 128, 32}, { |
| 0x14e4, 0x1647, 0x14e4, 0x000b, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x1647, 0x14e4, 0x800a, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x1647, 0x0e11, 0x9a, 0, 0, NC7770, 128, 32}, { |
| 0x14e4, 0x1647, 0x0e11, 0x99, 0, 0, NC7780, 128, 32}, { |
| 0x14e4, 0x1647, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x16a7, 0x14e4, 0x0009, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x16a7, 0x14e4, 0x000a, 0, 0, BCM5703A31, 128, 32}, { |
| 0x14e4, 0x16a7, 0x14e4, 0x000b, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x16a7, 0x14e4, 0x800a, 0, 0, BCM5703, 128, 32}, { |
| 0x14e4, 0x16a7, 0x0e11, 0x9a, 0, 0, NC7770, 128, 32}, { |
| 0x14e4, 0x16a7, 0x0e11, 0x99, 0, 0, NC7780, 128, 32}, { |
| 0x14e4, 0x16a7, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5703, 128, 32} |
| }; |
| |
| #define n570xDevices (sizeof(bcm570xDevices)/sizeof(bcm570xDevices[0])) |
| |
| /* |
| * Allocate a packet buffer from the bcm570x packet pool. |
| */ |
| void *bcm570xPktAlloc (int u, int pksize) |
| { |
| return malloc (pksize); |
| } |
| |
| /* |
| * Free a packet previously allocated from the bcm570x packet |
| * buffer pool. |
| */ |
| void bcm570xPktFree (int u, void *p) |
| { |
| free (p); |
| } |
| |
| int bcm570xReplenishRxBuffers (PUM_DEVICE_BLOCK pUmDevice) |
| { |
| PLM_PACKET pPacket; |
| PUM_PACKET pUmPacket; |
| void *skb; |
| int queue_rx = 0; |
| int ret = 0; |
| |
| while ((pUmPacket = (PUM_PACKET) |
| QQ_PopHead (&pUmDevice->rx_out_of_buf_q.Container)) != 0) { |
| |
| pPacket = (PLM_PACKET) pUmPacket; |
| |
| /* reuse an old skb */ |
| if (pUmPacket->skbuff) { |
| QQ_PushTail (&pDevice->RxPacketFreeQ.Container, |
| pPacket); |
| queue_rx = 1; |
| continue; |
| } |
| if ((skb = bcm570xPktAlloc (pUmDevice->index, |
| pPacket->u.Rx.RxBufferSize + 2)) == |
| 0) { |
| QQ_PushHead (&pUmDevice->rx_out_of_buf_q.Container, |
| pPacket); |
| printf ("NOTICE: Out of RX memory.\n"); |
| ret = 1; |
| break; |
| } |
| |
| pUmPacket->skbuff = skb; |
| QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket); |
| queue_rx = 1; |
| } |
| |
| if (queue_rx) { |
| LM_QueueRxPackets (pDevice); |
| } |
| |
| return ret; |
| } |
| |
| /* |
| * Probe, Map, and Init 570x device. |
| */ |
| int eth_init (bd_t * bis) |
| { |
| int i, rv, devFound = FALSE; |
| pci_dev_t devbusfn; |
| unsigned short status; |
| |
| /* Find PCI device, if it exists, configure ... */ |
| for (i = 0; i < n570xDevices; i++) { |
| devbusfn = pci_find_device (bcm570xDevices[i].vendor_id, |
| bcm570xDevices[i].device_id, 0); |
| if (devbusfn == -1) { |
| continue; /* No device of that vendor/device ID */ |
| } else { |
| |
| /* Set ILINE */ |
| pci_write_config_byte (devbusfn, |
| PCI_INTERRUPT_LINE, |
| BCM570X_ILINE); |
| |
| /* |
| * 0x10 - 0x14 define one 64-bit MBAR. |
| * 0x14 is the higher-order address bits of the BAR. |
| */ |
| pci_write_config_dword (devbusfn, |
| PCI_BASE_ADDRESS_1, 0); |
| |
| ioBase = BCM570X_MBAR; |
| |
| pci_write_config_dword (devbusfn, |
| PCI_BASE_ADDRESS_0, ioBase); |
| |
| /* |
| * Enable PCI memory, IO, and Master -- don't |
| * reset any status bits in doing so. |
| */ |
| pci_read_config_word (devbusfn, PCI_COMMAND, &status); |
| |
| status |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; |
| |
| pci_write_config_word (devbusfn, PCI_COMMAND, status); |
| |
| printf |
| ("\n%s: bus %d, device %d, function %d: MBAR=0x%x\n", |
| board_info[bcm570xDevices[i].board_id].name, |
| PCI_BUS (devbusfn), PCI_DEV (devbusfn), |
| PCI_FUNC (devbusfn), ioBase); |
| |
| /* Allocate once, but always clear on init */ |
| if (!pDevice) { |
| pDevice = malloc (sizeof (UM_DEVICE_BLOCK)); |
| pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| memset (pDevice, 0x0, sizeof (UM_DEVICE_BLOCK)); |
| } |
| |
| /* Configure pci dev structure */ |
| pUmDevice->pdev = devbusfn; |
| pUmDevice->index = 0; |
| pUmDevice->tx_pkt = 0; |
| pUmDevice->rx_pkt = 0; |
| devFound = TRUE; |
| break; |
| } |
| } |
| |
| if (!devFound) { |
| printf |
| ("eth_init: FAILURE: no BCM570x Ethernet devices found.\n"); |
| return -1; |
| } |
| |
| /* Setup defaults for chip */ |
| pDevice->TaskToOffload = LM_TASK_OFFLOAD_NONE; |
| |
| if (pDevice->ChipRevId == T3_CHIP_ID_5700_B0) { |
| pDevice->TaskToOffload = LM_TASK_OFFLOAD_NONE; |
| } else { |
| |
| if (rx_checksum[i]) { |
| pDevice->TaskToOffload |= |
| LM_TASK_OFFLOAD_RX_TCP_CHECKSUM | |
| LM_TASK_OFFLOAD_RX_UDP_CHECKSUM; |
| } |
| |
| if (tx_checksum[i]) { |
| pDevice->TaskToOffload |= |
| LM_TASK_OFFLOAD_TX_TCP_CHECKSUM | |
| LM_TASK_OFFLOAD_TX_UDP_CHECKSUM; |
| pDevice->NoTxPseudoHdrChksum = TRUE; |
| } |
| } |
| |
| /* Set Device PCI Memory base address */ |
| pDevice->pMappedMemBase = (PLM_UINT8) ioBase; |
| |
| /* Pull down adapter info */ |
| if ((rv = LM_GetAdapterInfo (pDevice)) != LM_STATUS_SUCCESS) { |
| printf ("bcm570xEnd: LM_GetAdapterInfo failed: rv=%d!\n", rv); |
| return -2; |
| } |
| |
| /* Lock not needed */ |
| pUmDevice->do_global_lock = 0; |
| |
| if (T3_ASIC_REV (pUmDevice->lm_dev.ChipRevId) == T3_ASIC_REV_5700) { |
| /* The 5700 chip works best without interleaved register */ |
| /* accesses on certain machines. */ |
| pUmDevice->do_global_lock = 1; |
| } |
| |
| /* Setup timer delays */ |
| if (T3_ASIC_REV (pDevice->ChipRevId) == T3_ASIC_REV_5701) { |
| pDevice->UseTaggedStatus = TRUE; |
| pUmDevice->timer_interval = CONFIG_SYS_HZ; |
| } else { |
| pUmDevice->timer_interval = CONFIG_SYS_HZ / 50; |
| } |
| |
| /* Grab name .... */ |
| pUmDevice->name = |
| (char *)malloc (strlen (board_info[bcm570xDevices[i].board_id].name) |
| + 1); |
| strcpy (pUmDevice->name, board_info[bcm570xDevices[i].board_id].name); |
| |
| memcpy (pDevice->NodeAddress, bis->bi_enetaddr, 6); |
| LM_SetMacAddress (pDevice, bis->bi_enetaddr); |
| /* Init queues .. */ |
| QQ_InitQueue (&pUmDevice->rx_out_of_buf_q.Container, |
| MAX_RX_PACKET_DESC_COUNT); |
| pUmDevice->rx_last_cnt = pUmDevice->tx_last_cnt = 0; |
| |
| /* delay for 4 seconds */ |
| pUmDevice->delayed_link_ind = (4 * CONFIG_SYS_HZ) / pUmDevice->timer_interval; |
| |
| pUmDevice->adaptive_expiry = CONFIG_SYS_HZ / pUmDevice->timer_interval; |
| |
| /* Sometimes we get spurious ints. after reset when link is down. */ |
| /* This field tells the isr to service the int. even if there is */ |
| /* no status block update. */ |
| pUmDevice->adapter_just_inited = |
| (3 * CONFIG_SYS_HZ) / pUmDevice->timer_interval; |
| |
| /* Initialize 570x */ |
| if (LM_InitializeAdapter (pDevice) != LM_STATUS_SUCCESS) { |
| printf ("ERROR: Adapter initialization failed.\n"); |
| return ERROR; |
| } |
| |
| /* Enable chip ISR */ |
| LM_EnableInterrupt (pDevice); |
| |
| /* Clear MC table */ |
| LM_MulticastClear (pDevice); |
| |
| /* Enable Multicast */ |
| LM_SetReceiveMask (pDevice, |
| pDevice->ReceiveMask | LM_ACCEPT_ALL_MULTICAST); |
| |
| pUmDevice->opened = 1; |
| pUmDevice->tx_full = 0; |
| pUmDevice->tx_pkt = 0; |
| pUmDevice->rx_pkt = 0; |
| printf ("eth%d: %s @0x%lx,", |
| pDevice->index, pUmDevice->name, (unsigned long)ioBase); |
| printf ("node addr "); |
| for (i = 0; i < 6; i++) { |
| printf ("%2.2x", pDevice->NodeAddress[i]); |
| } |
| printf ("\n"); |
| |
| printf ("eth%d: ", pDevice->index); |
| printf ("%s with ", chip_rev[bcm570xDevices[i].board_id].name); |
| |
| if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5400_PHY_ID) |
| printf ("Broadcom BCM5400 Copper "); |
| else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5401_PHY_ID) |
| printf ("Broadcom BCM5401 Copper "); |
| else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5411_PHY_ID) |
| printf ("Broadcom BCM5411 Copper "); |
| else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5701_PHY_ID) |
| printf ("Broadcom BCM5701 Integrated Copper "); |
| else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5703_PHY_ID) |
| printf ("Broadcom BCM5703 Integrated Copper "); |
| else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM8002_PHY_ID) |
| printf ("Broadcom BCM8002 SerDes "); |
| else if (pDevice->EnableTbi) |
| printf ("Agilent HDMP-1636 SerDes "); |
| else |
| printf ("Unknown "); |
| printf ("transceiver found\n"); |
| |
| printf ("eth%d: %s, MTU: %d,", |
| pDevice->index, pDevice->BusSpeedStr, 1500); |
| |
| if ((pDevice->ChipRevId != T3_CHIP_ID_5700_B0) && rx_checksum[i]) |
| printf ("Rx Checksum ON\n"); |
| else |
| printf ("Rx Checksum OFF\n"); |
| initialized++; |
| |
| return 0; |
| } |
| |
| /* Ethernet Interrupt service routine */ |
| void eth_isr (void) |
| { |
| LM_UINT32 oldtag, newtag; |
| int i; |
| |
| pUmDevice->interrupt = 1; |
| |
| if (pDevice->UseTaggedStatus) { |
| if ((pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_UPDATED) || |
| pUmDevice->adapter_just_inited) { |
| MB_REG_WR (pDevice, Mailbox.Interrupt[0].Low, 1); |
| oldtag = pDevice->pStatusBlkVirt->StatusTag; |
| |
| for (i = 0;; i++) { |
| pDevice->pStatusBlkVirt->Status &= |
| ~STATUS_BLOCK_UPDATED; |
| LM_ServiceInterrupts (pDevice); |
| newtag = pDevice->pStatusBlkVirt->StatusTag; |
| if ((newtag == oldtag) || (i > 50)) { |
| MB_REG_WR (pDevice, |
| Mailbox.Interrupt[0].Low, |
| newtag << 24); |
| if (pDevice->UndiFix) { |
| REG_WR (pDevice, Grc.LocalCtrl, |
| pDevice-> |
| GrcLocalCtrl | 0x2); |
| } |
| break; |
| } |
| oldtag = newtag; |
| } |
| } |
| } else { |
| while (pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_UPDATED) { |
| unsigned int dummy; |
| |
| pDevice->pMemView->Mailbox.Interrupt[0].Low = 1; |
| pDevice->pStatusBlkVirt->Status &= |
| ~STATUS_BLOCK_UPDATED; |
| LM_ServiceInterrupts (pDevice); |
| pDevice->pMemView->Mailbox.Interrupt[0].Low = 0; |
| dummy = pDevice->pMemView->Mailbox.Interrupt[0].Low; |
| } |
| } |
| |
| /* Allocate new RX buffers */ |
| if (QQ_GetEntryCnt (&pUmDevice->rx_out_of_buf_q.Container)) { |
| bcm570xReplenishRxBuffers (pUmDevice); |
| } |
| |
| /* Queue packets */ |
| if (QQ_GetEntryCnt (&pDevice->RxPacketFreeQ.Container)) { |
| LM_QueueRxPackets (pDevice); |
| } |
| |
| if (pUmDevice->tx_queued) { |
| pUmDevice->tx_queued = 0; |
| } |
| |
| if (pUmDevice->tx_full) { |
| if (pDevice->LinkStatus != LM_STATUS_LINK_DOWN) { |
| printf |
| ("NOTICE: tx was previously blocked, restarting MUX\n"); |
| pUmDevice->tx_full = 0; |
| } |
| } |
| |
| pUmDevice->interrupt = 0; |
| |
| } |
| |
| int eth_send (volatile void *packet, int length) |
| { |
| int status = 0; |
| #if ET_DEBUG |
| unsigned char *ptr = (unsigned char *)packet; |
| #endif |
| PLM_PACKET pPacket; |
| PUM_PACKET pUmPacket; |
| |
| /* Link down, return */ |
| while (pDevice->LinkStatus == LM_STATUS_LINK_DOWN) { |
| #if 0 |
| printf ("eth%d: link down - check cable or link partner.\n", |
| pUmDevice->index); |
| #endif |
| eth_isr (); |
| |
| /* Wait to see link for one-half a second before sending ... */ |
| udelay (1500000); |
| |
| } |
| |
| /* Clear sent flag */ |
| pUmDevice->tx_pkt = 0; |
| |
| /* Previously blocked */ |
| if (pUmDevice->tx_full) { |
| printf ("eth%d: tx blocked.\n", pUmDevice->index); |
| return 0; |
| } |
| |
| pPacket = (PLM_PACKET) |
| QQ_PopHead (&pDevice->TxPacketFreeQ.Container); |
| |
| if (pPacket == 0) { |
| pUmDevice->tx_full = 1; |
| printf ("bcm570xEndSend: TX full!\n"); |
| return 0; |
| } |
| |
| if (pDevice->SendBdLeft.counter == 0) { |
| pUmDevice->tx_full = 1; |
| printf ("bcm570xEndSend: no more TX descriptors!\n"); |
| QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket); |
| return 0; |
| } |
| |
| if (length <= 0) { |
| printf ("eth: bad packet size: %d\n", length); |
| goto out; |
| } |
| |
| /* Get packet buffers and fragment list */ |
| pUmPacket = (PUM_PACKET) pPacket; |
| /* Single DMA Descriptor transmit. |
| * Fragments may be provided, but one DMA descriptor max is |
| * used to send the packet. |
| */ |
| if (MM_CoalesceTxBuffer (pDevice, pPacket) != LM_STATUS_SUCCESS) { |
| if (pUmPacket->skbuff == NULL) { |
| /* Packet was discarded */ |
| printf ("TX: failed (1)\n"); |
| status = 1; |
| } else { |
| printf ("TX: failed (2)\n"); |
| status = 2; |
| } |
| QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket); |
| return status; |
| } |
| |
| /* Copy packet to DMA buffer */ |
| memset (pUmPacket->skbuff, 0x0, MAX_PACKET_SIZE); |
| memcpy ((void *)pUmPacket->skbuff, (void *)packet, length); |
| pPacket->PacketSize = length; |
| pPacket->Flags |= SND_BD_FLAG_END | SND_BD_FLAG_COAL_NOW; |
| pPacket->u.Tx.FragCount = 1; |
| /* We've already provided a frame ready for transmission */ |
| pPacket->Flags &= ~SND_BD_FLAG_TCP_UDP_CKSUM; |
| |
| if (LM_SendPacket (pDevice, pPacket) == LM_STATUS_FAILURE) { |
| /* |
| * A lower level send failure will push the packet descriptor back |
| * in the free queue, so just deal with the VxWorks clusters. |
| */ |
| if (pUmPacket->skbuff == NULL) { |
| printf ("TX failed (1)!\n"); |
| /* Packet was discarded */ |
| status = 3; |
| } else { |
| /* A resource problem ... */ |
| printf ("TX failed (2)!\n"); |
| status = 4; |
| } |
| |
| if (QQ_GetEntryCnt (&pDevice->TxPacketFreeQ.Container) == 0) { |
| printf ("TX: emptyQ!\n"); |
| pUmDevice->tx_full = 1; |
| } |
| } |
| |
| while (pUmDevice->tx_pkt == 0) { |
| /* Service TX */ |
| eth_isr (); |
| } |
| #if ET_DEBUG |
| printf ("eth_send: 0x%x, %d bytes\n" |
| "[%x %x %x %x %x %x %x %x %x %x %x %x %x %x %x %x] ...\n", |
| (int)pPacket, length, |
| ptr[0], ptr[1], ptr[2], ptr[3], ptr[4], ptr[5], |
| ptr[6], ptr[7], ptr[8], ptr[9], ptr[10], ptr[11], ptr[12], |
| ptr[13], ptr[14], ptr[15]); |
| #endif |
| pUmDevice->tx_pkt = 0; |
| QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket); |
| |
| /* Done with send */ |
| out: |
| return status; |
| } |
| |
| /* Ethernet receive */ |
| int eth_rx (void) |
| { |
| PLM_PACKET pPacket = NULL; |
| PUM_PACKET pUmPacket = NULL; |
| void *skb; |
| int size = 0; |
| |
| while (TRUE) { |
| |
| bcm570x_service_isr: |
| /* Pull down packet if it is there */ |
| eth_isr (); |
| |
| /* Indicate RX packets called */ |
| if (pUmDevice->rx_pkt) { |
| /* printf("eth_rx: got a packet...\n"); */ |
| pUmDevice->rx_pkt = 0; |
| } else { |
| /* printf("eth_rx: waiting for packet...\n"); */ |
| goto bcm570x_service_isr; |
| } |
| |
| pPacket = (PLM_PACKET) |
| QQ_PopHead (&pDevice->RxPacketReceivedQ.Container); |
| |
| if (pPacket == 0) { |
| printf ("eth_rx: empty packet!\n"); |
| goto bcm570x_service_isr; |
| } |
| |
| pUmPacket = (PUM_PACKET) pPacket; |
| #if ET_DEBUG |
| printf ("eth_rx: packet @0x%x\n", (int)pPacket); |
| #endif |
| /* If the packet generated an error, reuse buffer */ |
| if ((pPacket->PacketStatus != LM_STATUS_SUCCESS) || |
| ((size = pPacket->PacketSize) > pDevice->RxMtu)) { |
| |
| /* reuse skb */ |
| QQ_PushTail (&pDevice->RxPacketFreeQ.Container, |
| pPacket); |
| printf ("eth_rx: error in packet dma!\n"); |
| goto bcm570x_service_isr; |
| } |
| |
| /* Set size and address */ |
| skb = pUmPacket->skbuff; |
| size = pPacket->PacketSize; |
| |
| /* Pass the packet up to the protocol |
| * layers. |
| */ |
| NetReceive (skb, size); |
| |
| /* Free packet buffer */ |
| bcm570xPktFree (pUmDevice->index, skb); |
| pUmPacket->skbuff = NULL; |
| |
| /* Reuse SKB */ |
| QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket); |
| |
| return 0; /* Got a packet, bail ... */ |
| } |
| return size; |
| } |
| |
| /* Shut down device */ |
| void eth_halt (void) |
| { |
| int i; |
| if (initialized) |
| if (pDevice && pUmDevice && pUmDevice->opened) { |
| printf ("\neth%d:%s,", pUmDevice->index, |
| pUmDevice->name); |
| printf ("HALT,"); |
| /* stop device */ |
| LM_Halt (pDevice); |
| printf ("POWER DOWN,"); |
| LM_SetPowerState (pDevice, LM_POWER_STATE_D3); |
| |
| /* Free the memory allocated by the device in tigon3 */ |
| for (i = 0; i < pUmDevice->mem_list_num; i++) { |
| if (pUmDevice->mem_list[i]) { |
| /* sanity check */ |
| if (pUmDevice->dma_list[i]) { /* cache-safe memory */ |
| free (pUmDevice->mem_list[i]); |
| } else { |
| free (pUmDevice->mem_list[i]); /* normal memory */ |
| } |
| } |
| } |
| pUmDevice->opened = 0; |
| free (pDevice); |
| pDevice = NULL; |
| pUmDevice = NULL; |
| initialized = 0; |
| printf ("done - offline.\n"); |
| } |
| } |
| |
| /* |
| * |
| * Middle Module: Interface between the HW driver (tigon3 modules) and |
| * the native (SENS) driver. These routines implement the system |
| * interface for tigon3 on VxWorks. |
| */ |
| |
| /* Middle module dependency - size of a packet descriptor */ |
| int MM_Packet_Desc_Size = sizeof (UM_PACKET); |
| |
| LM_STATUS |
| MM_ReadConfig32 (PLM_DEVICE_BLOCK pDevice, |
| LM_UINT32 Offset, LM_UINT32 * pValue32) |
| { |
| UM_DEVICE_BLOCK *pUmDevice; |
| pUmDevice = (UM_DEVICE_BLOCK *) pDevice; |
| pci_read_config_dword (pUmDevice->pdev, Offset, (u32 *) pValue32); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS |
| MM_WriteConfig32 (PLM_DEVICE_BLOCK pDevice, LM_UINT32 Offset, LM_UINT32 Value32) |
| { |
| UM_DEVICE_BLOCK *pUmDevice; |
| pUmDevice = (UM_DEVICE_BLOCK *) pDevice; |
| pci_write_config_dword (pUmDevice->pdev, Offset, Value32); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS |
| MM_ReadConfig16 (PLM_DEVICE_BLOCK pDevice, |
| LM_UINT32 Offset, LM_UINT16 * pValue16) |
| { |
| UM_DEVICE_BLOCK *pUmDevice; |
| pUmDevice = (UM_DEVICE_BLOCK *) pDevice; |
| pci_read_config_word (pUmDevice->pdev, Offset, (u16 *) pValue16); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS |
| MM_WriteConfig16 (PLM_DEVICE_BLOCK pDevice, LM_UINT32 Offset, LM_UINT16 Value16) |
| { |
| UM_DEVICE_BLOCK *pUmDevice; |
| pUmDevice = (UM_DEVICE_BLOCK *) pDevice; |
| pci_write_config_word (pUmDevice->pdev, Offset, Value16); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS |
| MM_AllocateSharedMemory (PLM_DEVICE_BLOCK pDevice, LM_UINT32 BlockSize, |
| PLM_VOID * pMemoryBlockVirt, |
| PLM_PHYSICAL_ADDRESS pMemoryBlockPhy, LM_BOOL Cached) |
| { |
| PLM_VOID pvirt; |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| dma_addr_t mapping; |
| |
| pvirt = malloc (BlockSize); |
| mapping = (dma_addr_t) (pvirt); |
| if (!pvirt) |
| return LM_STATUS_FAILURE; |
| |
| pUmDevice->mem_list[pUmDevice->mem_list_num] = pvirt; |
| pUmDevice->dma_list[pUmDevice->mem_list_num] = mapping; |
| pUmDevice->mem_size_list[pUmDevice->mem_list_num++] = BlockSize; |
| memset (pvirt, 0, BlockSize); |
| |
| *pMemoryBlockVirt = (PLM_VOID) pvirt; |
| MM_SetAddr (pMemoryBlockPhy, (dma_addr_t) mapping); |
| |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS |
| MM_AllocateMemory (PLM_DEVICE_BLOCK pDevice, LM_UINT32 BlockSize, |
| PLM_VOID * pMemoryBlockVirt) |
| { |
| PLM_VOID pvirt; |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| |
| pvirt = malloc (BlockSize); |
| |
| if (!pvirt) |
| return LM_STATUS_FAILURE; |
| |
| pUmDevice->mem_list[pUmDevice->mem_list_num] = pvirt; |
| pUmDevice->dma_list[pUmDevice->mem_list_num] = 0; |
| pUmDevice->mem_size_list[pUmDevice->mem_list_num++] = BlockSize; |
| memset (pvirt, 0, BlockSize); |
| *pMemoryBlockVirt = pvirt; |
| |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_MapMemBase (PLM_DEVICE_BLOCK pDevice) |
| { |
| printf ("BCM570x PCI Memory base address @0x%x\n", |
| (unsigned int)pDevice->pMappedMemBase); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_InitializeUmPackets (PLM_DEVICE_BLOCK pDevice) |
| { |
| int i; |
| void *skb; |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| PUM_PACKET pUmPacket = NULL; |
| PLM_PACKET pPacket = NULL; |
| |
| for (i = 0; i < pDevice->RxPacketDescCnt; i++) { |
| pPacket = QQ_PopHead (&pDevice->RxPacketFreeQ.Container); |
| pUmPacket = (PUM_PACKET) pPacket; |
| |
| if (pPacket == 0) { |
| printf ("MM_InitializeUmPackets: Bad RxPacketFreeQ\n"); |
| } |
| |
| skb = bcm570xPktAlloc (pUmDevice->index, |
| pPacket->u.Rx.RxBufferSize + 2); |
| |
| if (skb == 0) { |
| pUmPacket->skbuff = 0; |
| QQ_PushTail (&pUmDevice->rx_out_of_buf_q.Container, |
| pPacket); |
| printf ("MM_InitializeUmPackets: out of buffer.\n"); |
| continue; |
| } |
| |
| pUmPacket->skbuff = skb; |
| QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket); |
| } |
| |
| pUmDevice->rx_low_buf_thresh = pDevice->RxPacketDescCnt / 8; |
| |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_GetConfig (PLM_DEVICE_BLOCK pDevice) |
| { |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| int index = pDevice->index; |
| |
| if (auto_speed[index] == 0) |
| pDevice->DisableAutoNeg = TRUE; |
| else |
| pDevice->DisableAutoNeg = FALSE; |
| |
| if (line_speed[index] == 0) { |
| pDevice->RequestedMediaType = LM_REQUESTED_MEDIA_TYPE_AUTO; |
| pDevice->DisableAutoNeg = FALSE; |
| } else { |
| if (line_speed[index] == 1000) { |
| if (pDevice->EnableTbi) { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_FIBER_1000MBPS_FULL_DUPLEX; |
| } else if (full_duplex[index]) { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS_FULL_DUPLEX; |
| } else { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS; |
| } |
| if (!pDevice->EnableTbi) |
| pDevice->DisableAutoNeg = FALSE; |
| } else if (line_speed[index] == 100) { |
| if (full_duplex[index]) { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS_FULL_DUPLEX; |
| } else { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS; |
| } |
| } else if (line_speed[index] == 10) { |
| if (full_duplex[index]) { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS_FULL_DUPLEX; |
| } else { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS; |
| } |
| } else { |
| pDevice->RequestedMediaType = |
| LM_REQUESTED_MEDIA_TYPE_AUTO; |
| pDevice->DisableAutoNeg = FALSE; |
| } |
| |
| } |
| pDevice->FlowControlCap = 0; |
| if (rx_flow_control[index] != 0) { |
| pDevice->FlowControlCap |= LM_FLOW_CONTROL_RECEIVE_PAUSE; |
| } |
| if (tx_flow_control[index] != 0) { |
| pDevice->FlowControlCap |= LM_FLOW_CONTROL_TRANSMIT_PAUSE; |
| } |
| if ((auto_flow_control[index] != 0) && |
| (pDevice->DisableAutoNeg == FALSE)) { |
| |
| pDevice->FlowControlCap |= LM_FLOW_CONTROL_AUTO_PAUSE; |
| if ((tx_flow_control[index] == 0) && |
| (rx_flow_control[index] == 0)) { |
| pDevice->FlowControlCap |= |
| LM_FLOW_CONTROL_TRANSMIT_PAUSE | |
| LM_FLOW_CONTROL_RECEIVE_PAUSE; |
| } |
| } |
| |
| /* Default MTU for now */ |
| pUmDevice->mtu = 1500; |
| |
| #if T3_JUMBO_RCV_RCB_ENTRY_COUNT |
| if (pUmDevice->mtu > 1500) { |
| pDevice->RxMtu = pUmDevice->mtu; |
| pDevice->RxJumboDescCnt = DEFAULT_JUMBO_RCV_DESC_COUNT; |
| } else { |
| pDevice->RxJumboDescCnt = 0; |
| } |
| pDevice->RxJumboDescCnt = rx_jumbo_desc_cnt[index]; |
| #else |
| pDevice->RxMtu = pUmDevice->mtu; |
| #endif |
| |
| if (T3_ASIC_REV (pDevice->ChipRevId) == T3_ASIC_REV_5701) { |
| pDevice->UseTaggedStatus = TRUE; |
| pUmDevice->timer_interval = CONFIG_SYS_HZ; |
| } else { |
| pUmDevice->timer_interval = CONFIG_SYS_HZ / 50; |
| } |
| |
| pDevice->TxPacketDescCnt = tx_pkt_desc_cnt[index]; |
| pDevice->RxStdDescCnt = rx_std_desc_cnt[index]; |
| /* Note: adaptive coalescence really isn't adaptive in this driver */ |
| pUmDevice->rx_adaptive_coalesce = rx_adaptive_coalesce[index]; |
| if (!pUmDevice->rx_adaptive_coalesce) { |
| pDevice->RxCoalescingTicks = rx_coalesce_ticks[index]; |
| if (pDevice->RxCoalescingTicks > MAX_RX_COALESCING_TICKS) |
| pDevice->RxCoalescingTicks = MAX_RX_COALESCING_TICKS; |
| pUmDevice->rx_curr_coalesce_ticks = pDevice->RxCoalescingTicks; |
| |
| pDevice->RxMaxCoalescedFrames = rx_max_coalesce_frames[index]; |
| if (pDevice->RxMaxCoalescedFrames > MAX_RX_MAX_COALESCED_FRAMES) |
| pDevice->RxMaxCoalescedFrames = |
| MAX_RX_MAX_COALESCED_FRAMES; |
| pUmDevice->rx_curr_coalesce_frames = |
| pDevice->RxMaxCoalescedFrames; |
| pDevice->StatsCoalescingTicks = stats_coalesce_ticks[index]; |
| if (pDevice->StatsCoalescingTicks > MAX_STATS_COALESCING_TICKS) |
| pDevice->StatsCoalescingTicks = |
| MAX_STATS_COALESCING_TICKS; |
| } else { |
| pUmDevice->rx_curr_coalesce_frames = |
| DEFAULT_RX_MAX_COALESCED_FRAMES; |
| pUmDevice->rx_curr_coalesce_ticks = DEFAULT_RX_COALESCING_TICKS; |
| } |
| pDevice->TxCoalescingTicks = tx_coalesce_ticks[index]; |
| if (pDevice->TxCoalescingTicks > MAX_TX_COALESCING_TICKS) |
| pDevice->TxCoalescingTicks = MAX_TX_COALESCING_TICKS; |
| pDevice->TxMaxCoalescedFrames = tx_max_coalesce_frames[index]; |
| if (pDevice->TxMaxCoalescedFrames > MAX_TX_MAX_COALESCED_FRAMES) |
| pDevice->TxMaxCoalescedFrames = MAX_TX_MAX_COALESCED_FRAMES; |
| |
| if (enable_wol[index]) { |
| pDevice->WakeUpModeCap = LM_WAKE_UP_MODE_MAGIC_PACKET; |
| pDevice->WakeUpMode = LM_WAKE_UP_MODE_MAGIC_PACKET; |
| } |
| pDevice->NicSendBd = TRUE; |
| |
| /* Don't update status blocks during interrupt */ |
| pDevice->RxCoalescingTicksDuringInt = 0; |
| pDevice->TxCoalescingTicksDuringInt = 0; |
| |
| return LM_STATUS_SUCCESS; |
| |
| } |
| |
| LM_STATUS MM_StartTxDma (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket) |
| { |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| printf ("Start TX DMA: dev=%d packet @0x%x\n", |
| (int)pUmDevice->index, (unsigned int)pPacket); |
| |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_CompleteTxDma (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket) |
| { |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| printf ("Complete TX DMA: dev=%d packet @0x%x\n", |
| (int)pUmDevice->index, (unsigned int)pPacket); |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_IndicateStatus (PLM_DEVICE_BLOCK pDevice, LM_STATUS Status) |
| { |
| char buf[128]; |
| char lcd[4]; |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| LM_FLOW_CONTROL flow_control; |
| |
| pUmDevice->delayed_link_ind = 0; |
| memset (lcd, 0x0, 4); |
| |
| if (Status == LM_STATUS_LINK_DOWN) { |
| sprintf (buf, "eth%d: %s: NIC Link is down\n", |
| pUmDevice->index, pUmDevice->name); |
| lcd[0] = 'L'; |
| lcd[1] = 'N'; |
| lcd[2] = 'K'; |
| lcd[3] = '?'; |
| } else if (Status == LM_STATUS_LINK_ACTIVE) { |
| sprintf (buf, "eth%d:%s: ", pUmDevice->index, pUmDevice->name); |
| |
| if (pDevice->LineSpeed == LM_LINE_SPEED_1000MBPS) { |
| strcat (buf, "1000 Mbps "); |
| lcd[0] = '1'; |
| lcd[1] = 'G'; |
| lcd[2] = 'B'; |
| } else if (pDevice->LineSpeed == LM_LINE_SPEED_100MBPS) { |
| strcat (buf, "100 Mbps "); |
| lcd[0] = '1'; |
| lcd[1] = '0'; |
| lcd[2] = '0'; |
| } else if (pDevice->LineSpeed == LM_LINE_SPEED_10MBPS) { |
| strcat (buf, "10 Mbps "); |
| lcd[0] = '1'; |
| lcd[1] = '0'; |
| lcd[2] = ' '; |
| } |
| if (pDevice->DuplexMode == LM_DUPLEX_MODE_FULL) { |
| strcat (buf, "full duplex"); |
| lcd[3] = 'F'; |
| } else { |
| strcat (buf, "half duplex"); |
| lcd[3] = 'H'; |
| } |
| strcat (buf, " link up"); |
| |
| flow_control = pDevice->FlowControl & |
| (LM_FLOW_CONTROL_RECEIVE_PAUSE | |
| LM_FLOW_CONTROL_TRANSMIT_PAUSE); |
| |
| if (flow_control) { |
| if (flow_control & LM_FLOW_CONTROL_RECEIVE_PAUSE) { |
| strcat (buf, ", receive "); |
| if (flow_control & |
| LM_FLOW_CONTROL_TRANSMIT_PAUSE) |
| strcat (buf, " & transmit "); |
| } else { |
| strcat (buf, ", transmit "); |
| } |
| strcat (buf, "flow control ON"); |
| } else { |
| strcat (buf, ", flow control OFF"); |
| } |
| strcat (buf, "\n"); |
| printf ("%s", buf); |
| } |
| #if 0 |
| sysLedDsply (lcd[0], lcd[1], lcd[2], lcd[3]); |
| #endif |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_FreeRxBuffer (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket) |
| { |
| |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| PUM_PACKET pUmPacket; |
| void *skb; |
| |
| pUmPacket = (PUM_PACKET) pPacket; |
| |
| if ((skb = pUmPacket->skbuff)) |
| bcm570xPktFree (pUmDevice->index, skb); |
| |
| pUmPacket->skbuff = 0; |
| |
| return LM_STATUS_SUCCESS; |
| } |
| |
| unsigned long MM_AnGetCurrentTime_us (PAN_STATE_INFO pAnInfo) |
| { |
| return get_timer (0); |
| } |
| |
| /* |
| * Transform an MBUF chain into a single MBUF. |
| * This routine will fail if the amount of data in the |
| * chain overflows a transmit buffer. In that case, |
| * the incoming MBUF chain will be freed. This routine can |
| * also fail by not being able to allocate a new MBUF (including |
| * cluster and mbuf headers). In that case the failure is |
| * non-fatal. The incoming cluster chain is not freed, giving |
| * the caller the choice of whether to try a retransmit later. |
| */ |
| LM_STATUS MM_CoalesceTxBuffer (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket) |
| { |
| PUM_PACKET pUmPacket = (PUM_PACKET) pPacket; |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| void *skbnew; |
| int len = 0; |
| |
| if (len == 0) |
| return (LM_STATUS_SUCCESS); |
| |
| if (len > MAX_PACKET_SIZE) { |
| printf ("eth%d: xmit frame discarded, too big!, size = %d\n", |
| pUmDevice->index, len); |
| return (LM_STATUS_FAILURE); |
| } |
| |
| skbnew = bcm570xPktAlloc (pUmDevice->index, MAX_PACKET_SIZE); |
| |
| if (skbnew == NULL) { |
| pUmDevice->tx_full = 1; |
| printf ("eth%d: out of transmit buffers", pUmDevice->index); |
| return (LM_STATUS_FAILURE); |
| } |
| |
| /* New packet values */ |
| pUmPacket->skbuff = skbnew; |
| pUmPacket->lm_packet.u.Tx.FragCount = 1; |
| |
| return (LM_STATUS_SUCCESS); |
| } |
| |
| LM_STATUS MM_IndicateRxPackets (PLM_DEVICE_BLOCK pDevice) |
| { |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| pUmDevice->rx_pkt = 1; |
| return LM_STATUS_SUCCESS; |
| } |
| |
| LM_STATUS MM_IndicateTxPackets (PLM_DEVICE_BLOCK pDevice) |
| { |
| PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice; |
| PLM_PACKET pPacket; |
| PUM_PACKET pUmPacket; |
| void *skb; |
| while (TRUE) { |
| |
| pPacket = (PLM_PACKET) |
| QQ_PopHead (&pDevice->TxPacketXmittedQ.Container); |
| |
| if (pPacket == 0) |
| break; |
| |
| pUmPacket = (PUM_PACKET) pPacket; |
| skb = (void *)pUmPacket->skbuff; |
| |
| /* |
| * Free MBLK if we transmitted a fragmented packet or a |
| * non-fragmented packet straight from the VxWorks |
| * buffer pool. If packet was copied to a local transmit |
| * buffer, then there's no MBUF to free, just free |
| * the transmit buffer back to the cluster pool. |
| */ |
| |
| if (skb) |
| bcm570xPktFree (pUmDevice->index, skb); |
| |
| pUmPacket->skbuff = 0; |
| QQ_PushTail (&pDevice->TxPacketFreeQ.Container, pPacket); |
| pUmDevice->tx_pkt = 1; |
| } |
| if (pUmDevice->tx_full) { |
| if (QQ_GetEntryCnt (&pDevice->TxPacketFreeQ.Container) >= |
| (QQ_GetSize (&pDevice->TxPacketFreeQ.Container) >> 1)) |
| pUmDevice->tx_full = 0; |
| } |
| return LM_STATUS_SUCCESS; |
| } |
| |
| /* |
| * Scan an MBUF chain until we reach fragment number "frag" |
| * Return its length and physical address. |
| */ |
| void MM_MapTxDma |
| (PLM_DEVICE_BLOCK pDevice, |
| struct _LM_PACKET *pPacket, |
| T3_64BIT_HOST_ADDR * paddr, LM_UINT32 * len, int frag) { |
| PUM_PACKET pUmPacket = (PUM_PACKET) pPacket; |
| *len = pPacket->PacketSize; |
| MM_SetT3Addr (paddr, (dma_addr_t) pUmPacket->skbuff); |
| } |
| |
| /* |
| * Convert an mbuf address, a CPU local virtual address, |
| * to a physical address as seen from a PCI device. Store the |
| * result at paddr. |
| */ |
| void MM_MapRxDma (PLM_DEVICE_BLOCK pDevice, |
| struct _LM_PACKET *pPacket, T3_64BIT_HOST_ADDR * paddr) |
| { |
| PUM_PACKET pUmPacket = (PUM_PACKET) pPacket; |
| MM_SetT3Addr (paddr, (dma_addr_t) pUmPacket->skbuff); |
| } |
| |
| void MM_SetAddr (LM_PHYSICAL_ADDRESS * paddr, dma_addr_t addr) |
| { |
| #if (BITS_PER_LONG == 64) |
| paddr->High = ((unsigned long)addr) >> 32; |
| paddr->Low = ((unsigned long)addr) & 0xffffffff; |
| #else |
| paddr->High = 0; |
| paddr->Low = (unsigned long)addr; |
| #endif |
| } |
| |
| void MM_SetT3Addr (T3_64BIT_HOST_ADDR * paddr, dma_addr_t addr) |
| { |
| unsigned long baddr = (unsigned long)addr; |
| #if (BITS_PER_LONG == 64) |
| set_64bit_addr (paddr, baddr & 0xffffffff, baddr >> 32); |
| #else |
| set_64bit_addr (paddr, baddr, 0); |
| #endif |
| } |
| |
| /* |
| * This combination of `inline' and `extern' has almost the effect of a |
| * macro. The way to use it is to put a function definition in a header |
| * file with these keywords, and put another copy of the definition |
| * (lacking `inline' and `extern') in a library file. The definition in |
| * the header file will cause most calls to the function to be inlined. |
| * If any uses of the function remain, they will refer to the single copy |
| * in the library. |
| */ |
| void atomic_set (atomic_t * entry, int val) |
| { |
| entry->counter = val; |
| } |
| |
| int atomic_read (atomic_t * entry) |
| { |
| return entry->counter; |
| } |
| |
| void atomic_inc (atomic_t * entry) |
| { |
| if (entry) |
| entry->counter++; |
| } |
| |
| void atomic_dec (atomic_t * entry) |
| { |
| if (entry) |
| entry->counter--; |
| } |
| |
| void atomic_sub (int a, atomic_t * entry) |
| { |
| if (entry) |
| entry->counter -= a; |
| } |
| |
| void atomic_add (int a, atomic_t * entry) |
| { |
| if (entry) |
| entry->counter += a; |
| } |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| void QQ_InitQueue (PQQ_CONTAINER pQueue, unsigned int QueueSize) |
| { |
| pQueue->Head = 0; |
| pQueue->Tail = 0; |
| pQueue->Size = QueueSize + 1; |
| atomic_set (&pQueue->EntryCnt, 0); |
| } /* QQ_InitQueue */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| char QQ_Full (PQQ_CONTAINER pQueue) |
| { |
| unsigned int NewHead; |
| |
| NewHead = (pQueue->Head + 1) % pQueue->Size; |
| |
| return (NewHead == pQueue->Tail); |
| } /* QQ_Full */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| char QQ_Empty (PQQ_CONTAINER pQueue) |
| { |
| return (pQueue->Head == pQueue->Tail); |
| } /* QQ_Empty */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| unsigned int QQ_GetSize (PQQ_CONTAINER pQueue) |
| { |
| return pQueue->Size; |
| } /* QQ_GetSize */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| unsigned int QQ_GetEntryCnt (PQQ_CONTAINER pQueue) |
| { |
| return atomic_read (&pQueue->EntryCnt); |
| } /* QQ_GetEntryCnt */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /* TRUE entry was added successfully. */ |
| /* FALSE queue is full. */ |
| /******************************************************************************/ |
| char QQ_PushHead (PQQ_CONTAINER pQueue, PQQ_ENTRY pEntry) |
| { |
| unsigned int Head; |
| |
| Head = (pQueue->Head + 1) % pQueue->Size; |
| |
| #if !defined(QQ_NO_OVERFLOW_CHECK) |
| if (Head == pQueue->Tail) { |
| return 0; |
| } /* if */ |
| #endif /* QQ_NO_OVERFLOW_CHECK */ |
| |
| pQueue->Array[pQueue->Head] = pEntry; |
| wmb (); |
| pQueue->Head = Head; |
| atomic_inc (&pQueue->EntryCnt); |
| |
| return -1; |
| } /* QQ_PushHead */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /* TRUE entry was added successfully. */ |
| /* FALSE queue is full. */ |
| /******************************************************************************/ |
| char QQ_PushTail (PQQ_CONTAINER pQueue, PQQ_ENTRY pEntry) |
| { |
| unsigned int Tail; |
| |
| Tail = pQueue->Tail; |
| if (Tail == 0) { |
| Tail = pQueue->Size; |
| } /* if */ |
| Tail--; |
| |
| #if !defined(QQ_NO_OVERFLOW_CHECK) |
| if (Tail == pQueue->Head) { |
| return 0; |
| } /* if */ |
| #endif /* QQ_NO_OVERFLOW_CHECK */ |
| |
| pQueue->Array[Tail] = pEntry; |
| wmb (); |
| pQueue->Tail = Tail; |
| atomic_inc (&pQueue->EntryCnt); |
| |
| return -1; |
| } /* QQ_PushTail */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| PQQ_ENTRY QQ_PopHead (PQQ_CONTAINER pQueue) |
| { |
| unsigned int Head; |
| PQQ_ENTRY Entry; |
| |
| Head = pQueue->Head; |
| |
| #if !defined(QQ_NO_UNDERFLOW_CHECK) |
| if (Head == pQueue->Tail) { |
| return (PQQ_ENTRY) 0; |
| } /* if */ |
| #endif /* QQ_NO_UNDERFLOW_CHECK */ |
| |
| if (Head == 0) { |
| Head = pQueue->Size; |
| } /* if */ |
| Head--; |
| |
| Entry = pQueue->Array[Head]; |
| membar (); |
| |
| pQueue->Head = Head; |
| atomic_dec (&pQueue->EntryCnt); |
| |
| return Entry; |
| } /* QQ_PopHead */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| PQQ_ENTRY QQ_PopTail (PQQ_CONTAINER pQueue) |
| { |
| unsigned int Tail; |
| PQQ_ENTRY Entry; |
| |
| Tail = pQueue->Tail; |
| |
| #if !defined(QQ_NO_UNDERFLOW_CHECK) |
| if (Tail == pQueue->Head) { |
| return (PQQ_ENTRY) 0; |
| } /* if */ |
| #endif /* QQ_NO_UNDERFLOW_CHECK */ |
| |
| Entry = pQueue->Array[Tail]; |
| membar (); |
| pQueue->Tail = (Tail + 1) % pQueue->Size; |
| atomic_dec (&pQueue->EntryCnt); |
| |
| return Entry; |
| } /* QQ_PopTail */ |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| PQQ_ENTRY QQ_GetHead (PQQ_CONTAINER pQueue, unsigned int Idx) |
| { |
| if (Idx >= atomic_read (&pQueue->EntryCnt)) { |
| return (PQQ_ENTRY) 0; |
| } |
| |
| if (pQueue->Head > Idx) { |
| Idx = pQueue->Head - Idx; |
| } else { |
| Idx = pQueue->Size - (Idx - pQueue->Head); |
| } |
| Idx--; |
| |
| return pQueue->Array[Idx]; |
| } |
| |
| /******************************************************************************/ |
| /* Description: */ |
| /* */ |
| /* Return: */ |
| /******************************************************************************/ |
| PQQ_ENTRY QQ_GetTail (PQQ_CONTAINER pQueue, unsigned int Idx) |
| { |
| if (Idx >= atomic_read (&pQueue->EntryCnt)) { |
| return (PQQ_ENTRY) 0; |
| } |
| |
| Idx += pQueue->Tail; |
| if (Idx >= pQueue->Size) { |
| Idx = Idx - pQueue->Size; |
| } |
| |
| return pQueue->Array[Idx]; |
| } |