| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * Copyright 2020 NXP |
| */ |
| |
| /* |
| * T1024/T1023 RDB board configuration file |
| */ |
| |
| #ifndef __T1024RDB_H |
| #define __T1024RDB_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ |
| #define CONFIG_ENABLE_36BIT_PHYS |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_ADDR_MAP 1 |
| #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ |
| #endif |
| |
| #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ |
| #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| /* support deep sleep */ |
| #ifdef CONFIG_ARCH_T1024 |
| #define CONFIG_DEEP_SLEEP |
| #endif |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg |
| #define CONFIG_SPL_FLUSH_IMAGE |
| #define CONFIG_SPL_PAD_TO 0x40000 |
| #define CONFIG_SPL_MAX_SIZE 0x28000 |
| #define RESET_VECTOR_OFFSET 0x27FFC |
| #define BOOT_PAGE_OFFSET 0x27000 |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SPL_SKIP_RELOCATE |
| #define CONFIG_SPL_COMMON_INIT_DDR |
| #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| #endif |
| |
| #ifdef CONFIG_MTD_RAW_NAND |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST 0x30000000 |
| #define CONFIG_SYS_NAND_U_BOOT_START 0x30000000 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_nand_rcw.cfg |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_nand_rcw.cfg |
| #endif |
| #endif |
| |
| #ifdef CONFIG_SPIFLASH |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC |
| #define CONFIG_SPL_SPI_FLASH_MINIMAL |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x30000000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MPC85XX_NO_RESETVEC |
| #endif |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_spi_rcw.cfg |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_spi_rcw.cfg |
| #endif |
| #endif |
| |
| #ifdef CONFIG_SDCARD |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC |
| #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_MMC_U_BOOT_DST (0x30000000) |
| #define CONFIG_SYS_MMC_U_BOOT_START (0x30000000) |
| #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MPC85XX_NO_RESETVEC |
| #endif |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_sd_rcw.cfg |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1023_sd_rcw.cfg |
| #endif |
| #endif |
| |
| #endif /* CONFIG_RAMBOOT_PBL */ |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| /* PCIe Boot - Master */ |
| #define CONFIG_SRIO_PCIE_BOOT_MASTER |
| /* |
| * for slave u-boot IMAGE instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull |
| #else |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000 |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000 |
| #endif |
| /* |
| * for slave UCODE and ENV instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull |
| #else |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000 |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000 |
| #endif |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ |
| /* slave core release by master*/ |
| #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 |
| #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ |
| |
| /* PCIe Boot - Slave */ |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) |
| /* Set 1M boot space for PCIe boot */ |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #endif |
| |
| #if defined(CONFIG_SPIFLASH) |
| #elif defined(CONFIG_SDCARD) |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #endif |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| #define CONFIG_SYS_CLK_FREQ 100000000 |
| #define CONFIG_DDR_CLK_FREQ 100000000 |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_SYS_CACHE_STASHING |
| #define CONFIG_BACKSIDE_L2_CACHE |
| #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E |
| #define CONFIG_BTB /* toggle branch predition */ |
| #define CONFIG_DDR_ECC |
| #ifdef CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #endif |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 |
| #define CONFIG_SYS_L3_SIZE (256 << 10) |
| #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) |
| #define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) |
| #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) |
| #define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) |
| #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_DCSRBAR 0xf0000000 |
| #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| #endif |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_DDR_SPD |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| #define SPD_EEPROM_ADDRESS 0x51 |
| #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_DDR_RAW_TIMING |
| #define CONFIG_SYS_SDRAM_SIZE 2048 |
| #endif |
| |
| /* |
| * IFC Definitions |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xe8000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) |
| #else |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| |
| /* NOR Flash Timing Params */ |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(0) | \ |
| CSOR_NAND_TRHZ_80 | CSOR_NOR_ADM_SHFT_MODE_EN) |
| #endif |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1A) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x0 |
| |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} |
| |
| #ifdef CONFIG_TARGET_T1024RDB |
| /* CPLD on IFC */ |
| #define CONFIG_SYS_CPLD_BASE 0xffdf0000 |
| #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) |
| #define CONFIG_SYS_CSPR2_EXT (0xf) |
| #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) |
| #define CONFIG_SYS_CSOR2 0x0 |
| |
| /* CPLD Timing parameters for IFC CS2 */ |
| #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ |
| FTIM1_GPCM_TRAD(0x1f)) |
| #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ |
| FTIM2_GPCM_TCH(0x8) | \ |
| FTIM2_GPCM_TWP(0x1f)) |
| #define CONFIG_SYS_CS2_FTIM3 0x0 |
| #endif |
| |
| /* NAND Flash on IFC */ |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_BASE 0xff800000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) |
| #else |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| #endif |
| #define CONFIG_SYS_NAND_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) |
| |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ |
| | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ |
| | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL 3Bytes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ |
| | CSOR_NAND_SPRZ_128 /* Spare size = 128 */ \ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| #endif |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_DDR_LAW 11 |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #if defined(CONFIG_MTD_RAW_NAND) |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #endif |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #endif |
| |
| #if defined(CONFIG_RAMBOOT_PBL) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_HWCONFIG |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| #endif |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) |
| |
| /* Serial Port */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) |
| #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) |
| |
| /* Video */ |
| #undef CONFIG_FSL_DIU_FB /* RDB doesn't support DIU */ |
| #ifdef CONFIG_FSL_DIU_FB |
| #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000) |
| #define CONFIG_VIDEO_LOGO |
| #define CONFIG_VIDEO_BMP_LOGO |
| #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS |
| /* |
| * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so |
| * disable empty flash sector detection, which is I/O-intensive. |
| */ |
| #undef CONFIG_SYS_FLASH_EMPTY_INFO |
| #endif |
| |
| /* I2C */ |
| #ifndef CONFIG_DM_I2C |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */ |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */ |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 |
| #else |
| #define CONFIG_I2C_SET_DEFAULT_BUS_NUM |
| #define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 |
| #endif |
| |
| #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ |
| #define I2C_PCA6408_BUS_NUM 1 |
| #define I2C_PCA6408_ADDR 0x20 |
| |
| /* I2C bus multiplexer */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| /* |
| * RTC configuration |
| */ |
| #define RTC |
| #define CONFIG_RTC_DS1337 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| |
| /* |
| * General PCIe |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| #define CONFIG_PCIE1 /* PCIE controller 1 */ |
| #define CONFIG_PCIE2 /* PCIE controller 2 */ |
| #define CONFIG_PCIE3 /* PCIE controller 3 */ |
| #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| |
| #ifdef CONFIG_PCI |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #ifdef CONFIG_PCIE1 |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| #endif |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #ifdef CONFIG_PCIE2 |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| #endif |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #ifdef CONFIG_PCIE3 |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull |
| #endif |
| |
| #if !defined(CONFIG_DM_PCI) |
| #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #endif |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #endif /* CONFIG_PCI */ |
| |
| /* |
| * USB |
| */ |
| #define CONFIG_HAS_FSL_DR_USB |
| |
| #ifdef CONFIG_HAS_FSL_DR_USB |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #endif |
| |
| /* |
| * SDHC |
| */ |
| #ifdef CONFIG_MMC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #endif |
| |
| /* Qman/Bman */ |
| #ifndef CONFIG_NOBQFMAN |
| #define CONFIG_SYS_BMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #else |
| #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE |
| #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ |
| CONFIG_SYS_BMAN_CENA_SIZE) |
| #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CONFIG_SYS_QMAN_NUM_PORTALS 10 |
| #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull |
| #else |
| #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE |
| #endif |
| #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE |
| #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ |
| CONFIG_SYS_QMAN_CENA_SIZE) |
| #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| |
| #define CONFIG_SYS_DPAA_FMAN |
| |
| /* Default address of microcode for the Linux FMan driver */ |
| #if defined(CONFIG_SPIFLASH) |
| /* |
| * env is stored at 0x100000, sector size is 0x10000, ucode is stored after |
| * env, so we got 0x110000. |
| */ |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 |
| #define CONFIG_SYS_QE_FW_ADDR 0x130000 |
| #elif defined(CONFIG_SDCARD) |
| /* |
| * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is |
| * about 1MB (2048 blocks), Env is stored after the image, and the env size is |
| * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820). |
| */ |
| #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) |
| #define CONFIG_SYS_QE_FW_ADDR (512 * 0x920) |
| #elif defined(CONFIG_MTD_RAW_NAND) |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #define CONFIG_SYS_QE_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #endif |
| #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| /* |
| * Slave has no ucode locally, it can fetch this from remote. When implementing |
| * in two corenet boards, slave's ucode could be stored in master's memory |
| * space, the address can be mapped from slave TLB->slave LAW-> |
| * slave SRIO or PCIE outbound window->master inbound window-> |
| * master LAW->the ucode address in master's memory space. |
| */ |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 |
| #else |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 |
| #define CONFIG_SYS_QE_FW_ADDR 0xEFE00000 |
| #endif |
| #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| #endif /* CONFIG_NOBQFMAN */ |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #if defined(CONFIG_TARGET_T1024RDB) |
| #define RGMII_PHY1_ADDR 0x2 |
| #define RGMII_PHY2_ADDR 0x6 |
| #define SGMII_AQR_PHY_ADDR 0x2 |
| #define FM1_10GEC1_PHY_ADDR 0x1 |
| #elif defined(CONFIG_TARGET_T1023RDB) |
| #define RGMII_PHY1_ADDR 0x1 |
| #define SGMII_RTK_PHY_ADDR 0x3 |
| #define SGMII_AQR_PHY_ADDR 0x2 |
| #endif |
| #endif |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_ETHPRIME "FM1@DTSEC4" |
| #endif |
| |
| /* |
| * Dynamic MTD Partition support with mtdparts |
| */ |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| #define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */ |
| #define __USB_PHY_TYPE utmi |
| |
| #ifdef CONFIG_ARCH_T1024 |
| #define CONFIG_BOARDNAME t1024rdb |
| #define BANK_INTLV cs0_cs1 |
| #else |
| #define CONFIG_BOARDNAME t1023rdb |
| #define BANK_INTLV null |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ |
| "bank_intlv=" __stringify(BANK_INTLV) "\0" \ |
| "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ |
| "ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \ |
| "fdtfile=" __stringify(CONFIG_BOARDNAME) "/" \ |
| __stringify(CONFIG_BOARDNAME) ".dtb\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ |
| "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \ |
| "netdev=eth0\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "fdtaddr=1e00000\0" \ |
| "bdev=sda3\0" |
| |
| #define CONFIG_LINUX \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "setenv ramdiskaddr 0x02000000;" \ |
| "setenv fdtaddr 0x00c00000;" \ |
| "setenv loadaddr 0x1000000;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_LINUX |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __T1024RDB_H */ |