| /* |
| * U-Boot - Configuration file for BR4 Appliance |
| * |
| * based on bf537-stamp.h |
| * Copyright (c) Switchfin Org. <dpn@switchfin.org> |
| */ |
| |
| #ifndef __CONFIG_BR4_H__ |
| #define __CONFIG_BR4_H__ |
| |
| #include <asm/config-pre.h> |
| |
| |
| /* |
| * Processor Settings |
| */ |
| #define CONFIG_BFIN_CPU bf537-0.3 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER |
| |
| |
| /* |
| * Clock Settings |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| */ |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 25000000 |
| /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ |
| /* 1 = CLKIN / 2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ |
| /* 1 = bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ |
| /* Values can range from 0-63 (where 0 means 64) */ |
| #define CONFIG_VCO_MULT 24 |
| /* CCLK_DIV controls the core clock divider */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* SCLK_DIV controls the system clock divider */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 5 |
| |
| |
| /* |
| * Memory Settings |
| */ |
| #define CONFIG_MEM_ADD_WDTH 10 |
| #define CONFIG_MEM_SIZE 64 |
| |
| #define CONFIG_EBIU_SDRRC_VAL 0x306 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x8091998d |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0xFF |
| #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 |
| |
| #define CONFIG_SYS_MONITOR_LEN (512 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (384 * 1024) |
| |
| |
| /* |
| * Network Settings |
| */ |
| #ifndef __ADSPBF534__ |
| #define ADI_CMDS_NETWORK 1 |
| #define CONFIG_BFIN_MAC |
| #define CONFIG_NETCONSOLE |
| #endif |
| #define CONFIG_HOSTNAME br4 |
| #define CONFIG_TFTP_BLOCKSIZE 4404 |
| |
| /* |
| * Flash Settings |
| */ |
| #define CONFIG_SYS_NO_FLASH /* We have no parallel FLASH */ |
| |
| |
| /* |
| * SPI Settings |
| */ |
| #define CONFIG_BFIN_SPI |
| #define CONFIG_ENV_SPI_MAX_HZ 30000000 |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| |
| |
| /* |
| * Env Storage Settings |
| */ |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_OFFSET 0x10000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #define CONFIG_ENV_IS_EMBEDDED_IN_LDR |
| |
| |
| /* |
| * I2C Settings |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_ADI |
| |
| |
| /* |
| * NAND Settings |
| */ |
| #define CONFIG_NAND_PLAT |
| #define CONFIG_SYS_NAND_BASE 0x20000000 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) |
| #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) |
| #define BFIN_NAND_WRITE(addr, cmd) \ |
| do { \ |
| bfin_write8(addr, cmd); \ |
| SSYNC(); \ |
| } while (0) |
| |
| #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) |
| #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) |
| #define NAND_PLAT_GPIO_DEV_READY GPIO_PF9 |
| |
| /* |
| * Misc Settings |
| */ |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_RTC_BFIN |
| #define CONFIG_UART_CONSOLE 0 |
| #define CONFIG_BOOTCOMMAND "run nandboot" |
| #define CONFIG_BOOTDELAY 2 |
| #define CONFIG_LOADADDR 0x2000000 |
| |
| /* |
| * Pull in common ADI header for remaining command/environment setup |
| */ |
| #include <configs/bfin_adi_common.h> |
| |
| /* |
| * Overwrite some settings defined in bfin_adi_common.h |
| */ |
| #undef NAND_ENV_SETTINGS |
| #define NAND_ENV_SETTINGS \ |
| "nandargs=set bootargs " CONFIG_BOOTARGS "\0" \ |
| "nandboot=" \ |
| "nand read $(loadaddr) 0x0 0x900000;" \ |
| "run nandargs;" \ |
| "bootm" \ |
| "\0" |
| |
| #endif |