blob: 6039fc4f62e58d8df5ef6824d9dde207ccc9e19a [file] [log] [blame]
/*
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale i.MX6Q SabreAuto board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __MX6QSABREAUTO_CONFIG_H
#define __MX6QSABREAUTO_CONFIG_H
#define CONFIG_MACH_TYPE 3529
#define CONFIG_MXC_UART_BASE UART4_BASE
#define CONFIG_CONSOLE_DEV "ttymxc3"
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
#define PHYS_SDRAM_SIZE (2u * 1024 * 1024 * 1024)
/* USB Configs */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x30, 8}, {0x32, 8}, {0x34, 8} }
#include "mx6sabre_common.h"
#undef CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
#define CONFIG_SYS_FLASH_SECT_SIZE (128 * 1024)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FSL_USDHC_NUM 2
#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_SYS_MMC_ENV_DEV 0
#endif
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
/* NAND flash command */
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
/* NAND stuff */
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8
/* PMIC */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#endif /* __MX6QSABREAUTO_CONFIG_H */