| /* |
| * U-boot - Configuration file for BF537 STAMP board |
| */ |
| |
| #ifndef __CONFIG_BF537_STAMP_H__ |
| #define __CONFIG_BF537_STAMP_H__ |
| |
| #include <asm/config-pre.h> |
| |
| |
| /* |
| * Processor Settings |
| */ |
| #define CONFIG_BFIN_CPU bf537-0.2 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS |
| |
| |
| /* |
| * Clock Settings |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| */ |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 25000000 |
| /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ |
| /* 1 = CLKIN / 2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ |
| /* 1 = bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ |
| /* Values can range from 0-63 (where 0 means 64) */ |
| #define CONFIG_VCO_MULT 20 |
| /* CCLK_DIV controls the core clock divider */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* SCLK_DIV controls the system clock divider */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 4 |
| |
| |
| /* |
| * Memory Settings |
| */ |
| #define CONFIG_MEM_ADD_WDTH 10 |
| #define CONFIG_MEM_SIZE 64 |
| |
| #define CONFIG_EBIU_SDRRC_VAL 0x306 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x91114d |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0xFF |
| #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 |
| |
| #define CONFIG_SYS_MONITOR_LEN (512 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (384 * 1024) |
| |
| |
| /* |
| * Network Settings |
| */ |
| #ifndef __ADSPBF534__ |
| #define ADI_CMDS_NETWORK 1 |
| #define CONFIG_BFIN_MAC |
| #define CONFIG_NETCONSOLE 1 |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| #define CONFIG_HOSTNAME bf537-stamp |
| /* Uncomment next line to use fixed MAC address */ |
| /* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */ |
| |
| |
| /* |
| * Flash Settings |
| */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_BASE 0x20000000 |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_PROTECTION |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 71 |
| |
| |
| /* |
| * SPI Settings |
| */ |
| #define CONFIG_BFIN_SPI |
| #define CONFIG_ENV_SPI_MAX_HZ 30000000 |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_ATMEL |
| #define CONFIG_SPI_FLASH_SPANSION |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define CONFIG_SPI_FLASH_WINBOND |
| |
| |
| /* |
| * Env Storage Settings |
| */ |
| #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_OFFSET 0x10000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_OFFSET 0x4000 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x2000 |
| #endif |
| #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) |
| #define ENV_IS_EMBEDDED |
| #else |
| #define CONFIG_ENV_IS_EMBEDDED_IN_LDR |
| #endif |
| #ifdef ENV_IS_EMBEDDED |
| /* WARNING - the following is hand-optimized to fit within |
| * the sector before the environment sector. If it throws |
| * an error during compilation remove an object here to get |
| * it linked after the configuration sector. |
| */ |
| # define LDS_BOARD_TEXT \ |
| cpu/blackfin/traps.o (.text .text.*); \ |
| cpu/blackfin/interrupt.o (.text .text.*); \ |
| cpu/blackfin/serial.o (.text .text.*); \ |
| common/dlmalloc.o (.text .text.*); \ |
| lib/crc32.o (.text .text.*); \ |
| . = DEFINED(env_offset) ? env_offset : .; \ |
| common/env_embedded.o (.text .text.*); |
| #endif |
| |
| |
| /* |
| * I2C Settings |
| */ |
| #define CONFIG_BFIN_TWI_I2C 1 |
| #define CONFIG_HARD_I2C 1 |
| #define CONFIG_SYS_I2C_SPEED 50000 |
| #define CONFIG_SYS_I2C_SLAVE 0 |
| |
| |
| /* |
| * SPI_MMC Settings |
| */ |
| #define CONFIG_MMC |
| #define CONFIG_SPI_MMC |
| |
| |
| /* |
| * NAND Settings |
| */ |
| /* #define CONFIG_NAND_PLAT */ |
| #define CONFIG_SYS_NAND_BASE 0x20212000 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) |
| #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) |
| #define BFIN_NAND_READY PF3 |
| #define BFIN_NAND_WRITE(addr, cmd) \ |
| do { \ |
| bfin_write8(addr, cmd); \ |
| SSYNC(); \ |
| } while (0) |
| |
| #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) |
| #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) |
| #define NAND_PLAT_DEV_READY(chip) (bfin_read_PORTFIO() & BFIN_NAND_READY) |
| #define NAND_PLAT_INIT() \ |
| do { \ |
| bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~BFIN_NAND_READY); \ |
| bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() & ~BFIN_NAND_READY); \ |
| bfin_write_PORTFIO_INEN(bfin_read_PORTFIO_INEN() | BFIN_NAND_READY); \ |
| } while (0) |
| |
| |
| /* |
| * CF-CARD IDE-HDD Support |
| */ |
| |
| /* |
| * Add CF flash card support in TRUE-IDE Mode (CF-IDE-NAND Card) |
| * Strange address mapping Blackfin A13 connects to CF_A0 |
| */ |
| |
| /* #define CONFIG_BFIN_TRUE_IDE */ |
| |
| /* |
| * Add CF flash card support in Common Memory Mode (CF-IDE-NAND Card) |
| * This should be the preferred mode |
| */ |
| |
| /* #define CONFIG_BFIN_CF_IDE */ |
| |
| /* |
| * Add IDE Disk Drive (HDD) support |
| * See example interface here: |
| * http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:ide-blackfin |
| */ |
| |
| /* #define CONFIG_BFIN_HDD_IDE */ |
| |
| #if defined(CONFIG_BFIN_CF_IDE) || \ |
| defined(CONFIG_BFIN_HDD_IDE) || \ |
| defined(CONFIG_BFIN_TRUE_IDE) |
| # define CONFIG_BFIN_IDE 1 |
| # define CONFIG_CMD_IDE |
| #endif |
| |
| #if defined(CONFIG_BFIN_IDE) |
| |
| #define CONFIG_DOS_PARTITION 1 |
| /* |
| * IDE/ATA stuff |
| */ |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ |
| #undef CONFIG_IDE_LED /* no led for ide supported */ |
| #undef CONFIG_IDE_RESET /* no reset for ide supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) |
| |
| #undef CONFIG_EBIU_AMBCTL1_VAL |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3 |
| |
| #define CONFIG_CF_ATASEL_DIS 0x20311800 |
| #define CONFIG_CF_ATASEL_ENA 0x20311802 |
| |
| #if defined(CONFIG_BFIN_TRUE_IDE) |
| /* |
| * Note that these settings aren't for the most part used in include/ata.h |
| * when all of the ATA registers are setup |
| */ |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ |
| #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A13 */ |
| |
| #elif defined(CONFIG_BFIN_CF_IDE) |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x20211800 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */ |
| #define CONFIG_SYS_ATA_STRIDE 1 /* CF_A0=0, with /CE1 /CE2 odd/even byte selects */ |
| |
| #elif defined(CONFIG_BFIN_HDD_IDE) |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x20314000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ |
| #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */ |
| #undef CONFIG_SCLK_DIV |
| #define CONFIG_SCLK_DIV 8 |
| #endif |
| |
| #endif |
| |
| |
| /* |
| * Misc Settings |
| */ |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_RTC_BFIN |
| #define CONFIG_UART_CONSOLE 0 |
| |
| /* #define CONFIG_BF537_STAMP_LEDCMD 1 */ |
| |
| /* Define if want to do post memory test */ |
| #undef CONFIG_POST |
| #ifdef CONFIG_POST |
| #define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ |
| #define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ |
| #endif |
| |
| /* These are for board tests */ |
| #if 0 |
| #define CONFIG_BOOTCOMMAND "bootldr 0x203f0100" |
| #define CONFIG_AUTOBOOT_KEYED |
| #define CONFIG_AUTOBOOT_PROMPT \ |
| "autoboot in %d seconds: press space to stop\n", bootdelay |
| #define CONFIG_AUTOBOOT_STOP_STR " " |
| #endif |
| |
| |
| /* |
| * Pull in common ADI header for remaining command/environment setup |
| */ |
| #include <configs/bfin_adi_common.h> |
| |
| #endif |