blob: de8dc1dac8ada7d128a0cb6824a37ead17ce4c01 [file] [log] [blame]
CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x23f00000
CONFIG_TARGET_SAM9X60EK=y
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_NR_DRAM_BANKS=8
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="sam9x60ek"
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xfffff200
CONFIG_DEBUG_UART_CLOCK=200000000
CONFIG_ENV_OFFSET_REDUND=0x100000
CONFIG_DEBUG_UART=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_FIT=y
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=12 root=ubi0:rootfs rw"
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_MISC_INIT_R=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_DM=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_HASH=y
CONFIG_HASH_VERIFY=y
CONFIG_CMD_FAT=y
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_DM=y
CONFIG_CLK=y
CONFIG_CLK_CCF=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GENERIC_CLK=y
CONFIG_AT91_SAM9X60_PLL=y
CONFIG_CPU=y
CONFIG_AT91_GPIO=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_AT91=y
CONFIG_I2C_EEPROM=y
CONFIG_MICROCHIP_FLEXCOM=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_MTD=y
# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
CONFIG_NAND_ATMEL=y
CONFIG_ATMEL_NAND_HW_PMECC=y
CONFIG_PMECC_CAP=8
CONFIG_SYS_NAND_ONFI_DETECTION=y
CONFIG_PHY_MICREL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_W1=y
CONFIG_W1_GPIO=y
CONFIG_W1_EEPROM=y
CONFIG_W1_EEPROM_DS24XXX=y
CONFIG_OF_LIBFDT_OVERLAY=y