blob: 49b0419e9a7748a9e86cab661338c0fd2be8b9d8 [file] [log] [blame]
/*
* Configuration file for the SAMA5D2 Xplained Board.
*
* Copyright (C) 2015 Atmel Corporation
* Wenyou Yang <wenyou.yang@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* No NOR flash, this definition should put before common header */
#define CONFIG_SYS_NO_FLASH
#include "at91-sama5_common.h"
#define CONFIG_MISC_INIT_R
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x210000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
/* SerialFlash */
#ifdef CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
/* NAND flash */
#undef CONFIG_CMD_NAND
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#endif
/* USB device */
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_DOS_PARTITION
#endif
/* I2C */
#define AT24MAC_ADDR 0x5c
#define AT24MAC_REG 0x9a
/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
/* LCD */
#ifdef CONFIG_LCD
#define LCD_BPP LCD_COLOR16
#define LCD_OUTPUT_BPP 24
#define CONFIG_LCD_LOGO
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
#endif
#ifdef CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env in sd card */
#undef FAT_ENV_DEVICE_AND_PART
#undef CONFIG_BOOTCOMMAND
#define FAT_ENV_DEVICE_AND_PART "1"
#define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-sama5d2_xplained.dtb; " \
"fatload mmc 1:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
#endif
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#elif CONFIG_SYS_USE_SERIALFLASH
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#endif
#endif