| /* |
| * U-boot - Configuration file for IP04 board (having BF532 processor) |
| * |
| * Copyright (c) 2006 Intratrade Ltd., Ivan Danov, idanov@gmail.com |
| * |
| * Copyright (c) 2005-2010 Analog Devices Inc. |
| * |
| * (C) Copyright 2000-2004 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #ifndef __CONFIG_IP04_H__ |
| #define __CONFIG_IP04_H__ |
| |
| #include <asm/config-pre.h> |
| |
| |
| /* |
| * Processor Settings |
| */ |
| #define CONFIG_BFIN_CPU bf532-0.5 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_NAND |
| |
| |
| /* |
| * Clock Settings |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| */ |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 10000000 |
| /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ |
| /* 1 = CLKIN / 2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ |
| /* 1 = bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ |
| /* Values can range from 0-63 (where 0 means 64) */ |
| #define CONFIG_VCO_MULT 40 |
| /* CCLK_DIV controls the core clock divider */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* SCLK_DIV controls the system clock divider */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 3 |
| |
| |
| /* |
| * Memory Settings |
| */ |
| #define CONFIG_MEM_ADD_WDTH 10 |
| #define CONFIG_MEM_SIZE 64 |
| |
| #define CONFIG_EBIU_SDRRC_VAL 0x408 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x9111cd |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0xFF |
| #define CONFIG_EBIU_AMBCTL0_VAL 0xffc2ffc2 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xffc2ffc2 |
| |
| #define CONFIG_SYS_MONITOR_LEN (384 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) |
| |
| |
| /* |
| * Network Settings |
| */ |
| #define ADI_CMDS_NETWORK 1 |
| #define CONFIG_HOSTNAME IP04 |
| |
| #define CONFIG_DRIVER_DM9000 1 |
| #define CONFIG_DM9000_NO_SROM |
| #define CONFIG_DM9000_BASE 0x20100000 |
| #define DM9000_IO CONFIG_DM9000_BASE |
| #define DM9000_DATA (CONFIG_DM9000_BASE + 2) |
| |
| |
| /* |
| * Flash Settings |
| */ |
| #define CONFIG_ENV_OVERWRITE 1 |
| #define CONFIG_SYS_NO_FLASH /* we have only NAND */ |
| |
| |
| /* |
| * SPI Settings |
| */ |
| #define CONFIG_BFIN_SPI |
| #define CONFIG_ENV_SPI_MAX_HZ 30000000 |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define CONFIG_SPI_FLASH_WINBOND |
| |
| |
| /* |
| * Env Storage Settings |
| */ |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_PREBOOT "echo starting from spi flash" |
| #define CONFIG_ENV_OFFSET 0x30000 |
| #define CONFIG_ENV_SIZE 0x10000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| |
| |
| /* |
| * NAND Settings |
| */ |
| #define CONFIG_NAND_PLAT |
| #define CONFIG_SYS_NAND_BASE 0x20000000 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) |
| #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) |
| #define BFIN_NAND_WRITE(addr, cmd) \ |
| do { \ |
| bfin_write8(addr, cmd); \ |
| SSYNC(); \ |
| } while (0) |
| |
| #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) |
| #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) |
| #define NAND_PLAT_GPIO_DEV_READY GPIO_PF10 |
| |
| |
| /* |
| * Misc Settings |
| */ |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_UART_CONSOLE 0 |
| |
| #undef CONFIG_SHOW_BOOT_PROGRESS |
| /* Enable this if bootretry required; currently it's disabled */ |
| #define CONFIG_BOOT_RETRY_TIME -1 |
| #define CONFIG_BOOTCOMMAND "run nandboot" |
| #define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n" |
| |
| |
| /* |
| * Pull in common ADI header for remaining command/environment setup |
| */ |
| #include <configs/bfin_adi_common.h> |
| |
| #endif |