| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * PCIe driver for Marvell MVEBU SoCs |
| * |
| * Based on Barebox drivers/pci/pci-mvebu.c |
| * |
| * Ported to U-Boot by: |
| * Anton Schubert <anton.schubert@gmx.de> |
| * Stefan Roese <sr@denx.de> |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <asm/global_data.h> |
| #include <dm/device-internal.h> |
| #include <dm/lists.h> |
| #include <dm/of_access.h> |
| #include <pci.h> |
| #include <asm/io.h> |
| #include <asm/arch/cpu.h> |
| #include <asm/arch/soc.h> |
| #include <linux/bitops.h> |
| #include <linux/errno.h> |
| #include <linux/ioport.h> |
| #include <linux/mbus.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| /* PCIe unit register offsets */ |
| #define SELECT(x, n) ((x >> n) & 1UL) |
| |
| #define PCIE_DEV_ID_OFF 0x0000 |
| #define PCIE_CMD_OFF 0x0004 |
| #define PCIE_DEV_REV_OFF 0x0008 |
| #define PCIE_BAR_LO_OFF(n) (0x0010 + ((n) << 3)) |
| #define PCIE_BAR_HI_OFF(n) (0x0014 + ((n) << 3)) |
| #define PCIE_CAPAB_OFF 0x0060 |
| #define PCIE_CTRL_STAT_OFF 0x0068 |
| #define PCIE_HEADER_LOG_4_OFF 0x0128 |
| #define PCIE_BAR_CTRL_OFF(n) (0x1804 + (((n) - 1) * 4)) |
| #define PCIE_WIN04_CTRL_OFF(n) (0x1820 + ((n) << 4)) |
| #define PCIE_WIN04_BASE_OFF(n) (0x1824 + ((n) << 4)) |
| #define PCIE_WIN04_REMAP_OFF(n) (0x182c + ((n) << 4)) |
| #define PCIE_WIN5_CTRL_OFF 0x1880 |
| #define PCIE_WIN5_BASE_OFF 0x1884 |
| #define PCIE_WIN5_REMAP_OFF 0x188c |
| #define PCIE_CONF_ADDR_OFF 0x18f8 |
| #define PCIE_CONF_ADDR_EN BIT(31) |
| #define PCIE_CONF_REG(r) ((((r) & 0xf00) << 16) | ((r) & 0xfc)) |
| #define PCIE_CONF_BUS(b) (((b) & 0xff) << 16) |
| #define PCIE_CONF_DEV(d) (((d) & 0x1f) << 11) |
| #define PCIE_CONF_FUNC(f) (((f) & 0x7) << 8) |
| #define PCIE_CONF_ADDR(dev, reg) \ |
| (PCIE_CONF_BUS(PCI_BUS(dev)) | PCIE_CONF_DEV(PCI_DEV(dev)) | \ |
| PCIE_CONF_FUNC(PCI_FUNC(dev)) | PCIE_CONF_REG(reg) | \ |
| PCIE_CONF_ADDR_EN) |
| #define PCIE_CONF_DATA_OFF 0x18fc |
| #define PCIE_MASK_OFF 0x1910 |
| #define PCIE_MASK_ENABLE_INTS (0xf << 24) |
| #define PCIE_CTRL_OFF 0x1a00 |
| #define PCIE_CTRL_X1_MODE BIT(0) |
| #define PCIE_STAT_OFF 0x1a04 |
| #define PCIE_STAT_BUS (0xff << 8) |
| #define PCIE_STAT_DEV (0x1f << 16) |
| #define PCIE_STAT_LINK_DOWN BIT(0) |
| #define PCIE_DEBUG_CTRL 0x1a60 |
| #define PCIE_DEBUG_SOFT_RESET BIT(20) |
| |
| struct mvebu_pcie { |
| struct pci_controller hose; |
| void __iomem *base; |
| void __iomem *membase; |
| struct resource mem; |
| void __iomem *iobase; |
| struct resource io; |
| u32 port; |
| u32 lane; |
| int devfn; |
| u32 lane_mask; |
| int first_busno; |
| int local_dev; |
| char name[16]; |
| unsigned int mem_target; |
| unsigned int mem_attr; |
| unsigned int io_target; |
| unsigned int io_attr; |
| }; |
| |
| /* |
| * MVEBU PCIe controller needs MEMORY and I/O BARs to be mapped |
| * into SoCs address space. Each controller will map 128M of MEM |
| * and 64K of I/O space when registered. |
| */ |
| static void __iomem *mvebu_pcie_membase = (void __iomem *)MBUS_PCI_MEM_BASE; |
| #define PCIE_MEM_SIZE (128 << 20) |
| static void __iomem *mvebu_pcie_iobase = (void __iomem *)MBUS_PCI_IO_BASE; |
| |
| static inline bool mvebu_pcie_link_up(struct mvebu_pcie *pcie) |
| { |
| u32 val; |
| val = readl(pcie->base + PCIE_STAT_OFF); |
| return !(val & PCIE_STAT_LINK_DOWN); |
| } |
| |
| static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie *pcie, int busno) |
| { |
| u32 stat; |
| |
| stat = readl(pcie->base + PCIE_STAT_OFF); |
| stat &= ~PCIE_STAT_BUS; |
| stat |= busno << 8; |
| writel(stat, pcie->base + PCIE_STAT_OFF); |
| } |
| |
| static void mvebu_pcie_set_local_dev_nr(struct mvebu_pcie *pcie, int devno) |
| { |
| u32 stat; |
| |
| stat = readl(pcie->base + PCIE_STAT_OFF); |
| stat &= ~PCIE_STAT_DEV; |
| stat |= devno << 16; |
| writel(stat, pcie->base + PCIE_STAT_OFF); |
| } |
| |
| static int mvebu_pcie_get_local_bus_nr(struct mvebu_pcie *pcie) |
| { |
| u32 stat; |
| |
| stat = readl(pcie->base + PCIE_STAT_OFF); |
| return (stat & PCIE_STAT_BUS) >> 8; |
| } |
| |
| static int mvebu_pcie_get_local_dev_nr(struct mvebu_pcie *pcie) |
| { |
| u32 stat; |
| |
| stat = readl(pcie->base + PCIE_STAT_OFF); |
| return (stat & PCIE_STAT_DEV) >> 16; |
| } |
| |
| static inline struct mvebu_pcie *hose_to_pcie(struct pci_controller *hose) |
| { |
| return container_of(hose, struct mvebu_pcie, hose); |
| } |
| |
| static int mvebu_pcie_valid_addr(struct mvebu_pcie *pcie, pci_dev_t bdf) |
| { |
| /* |
| * There are two devices visible on local bus: |
| * * on slot configured by function mvebu_pcie_set_local_dev_nr() |
| * (by default this register is set to 0) there is a |
| * "Marvell Memory controller", which isn't useful in root complex |
| * mode, |
| * * on all other slots the real PCIe card connected to the PCIe slot. |
| * |
| * We therefore allow access only to the real PCIe card. |
| */ |
| if (PCI_BUS(bdf) == pcie->first_busno && |
| PCI_DEV(bdf) != !pcie->local_dev) |
| return 0; |
| |
| return 1; |
| } |
| |
| static int mvebu_pcie_read_config(const struct udevice *bus, pci_dev_t bdf, |
| uint offset, ulong *valuep, |
| enum pci_size_t size) |
| { |
| struct mvebu_pcie *pcie = dev_get_plat(bus); |
| u32 data; |
| |
| debug("PCIE CFG read: (b,d,f)=(%2d,%2d,%2d) ", |
| PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf)); |
| |
| if (!mvebu_pcie_valid_addr(pcie, bdf)) { |
| debug("- out of range\n"); |
| *valuep = pci_get_ff(size); |
| return 0; |
| } |
| |
| /* write address */ |
| writel(PCIE_CONF_ADDR(bdf, offset), pcie->base + PCIE_CONF_ADDR_OFF); |
| |
| /* read data */ |
| data = readl(pcie->base + PCIE_CONF_DATA_OFF); |
| debug("(addr,size,val)=(0x%04x, %d, 0x%08x)\n", offset, size, data); |
| *valuep = pci_conv_32_to_size(data, offset, size); |
| |
| return 0; |
| } |
| |
| static int mvebu_pcie_write_config(struct udevice *bus, pci_dev_t bdf, |
| uint offset, ulong value, |
| enum pci_size_t size) |
| { |
| struct mvebu_pcie *pcie = dev_get_plat(bus); |
| u32 data; |
| |
| debug("PCIE CFG write: (b,d,f)=(%2d,%2d,%2d) ", |
| PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf)); |
| debug("(addr,size,val)=(0x%04x, %d, 0x%08lx)\n", offset, size, value); |
| |
| if (!mvebu_pcie_valid_addr(pcie, bdf)) { |
| debug("- out of range\n"); |
| return 0; |
| } |
| |
| /* write address */ |
| writel(PCIE_CONF_ADDR(bdf, offset), pcie->base + PCIE_CONF_ADDR_OFF); |
| |
| /* write data */ |
| data = pci_conv_size_to_32(0, value, offset, size); |
| writel(data, pcie->base + PCIE_CONF_DATA_OFF); |
| |
| return 0; |
| } |
| |
| /* |
| * Setup PCIE BARs and Address Decode Wins: |
| * BAR[0,2] -> disabled, BAR[1] -> covers all DRAM banks |
| * WIN[0-3] -> DRAM bank[0-3] |
| */ |
| static void mvebu_pcie_setup_wins(struct mvebu_pcie *pcie) |
| { |
| const struct mbus_dram_target_info *dram = mvebu_mbus_dram_info(); |
| u32 size; |
| int i; |
| |
| /* First, disable and clear BARs and windows. */ |
| for (i = 1; i < 3; i++) { |
| writel(0, pcie->base + PCIE_BAR_CTRL_OFF(i)); |
| writel(0, pcie->base + PCIE_BAR_LO_OFF(i)); |
| writel(0, pcie->base + PCIE_BAR_HI_OFF(i)); |
| } |
| |
| for (i = 0; i < 5; i++) { |
| writel(0, pcie->base + PCIE_WIN04_CTRL_OFF(i)); |
| writel(0, pcie->base + PCIE_WIN04_BASE_OFF(i)); |
| writel(0, pcie->base + PCIE_WIN04_REMAP_OFF(i)); |
| } |
| |
| writel(0, pcie->base + PCIE_WIN5_CTRL_OFF); |
| writel(0, pcie->base + PCIE_WIN5_BASE_OFF); |
| writel(0, pcie->base + PCIE_WIN5_REMAP_OFF); |
| |
| /* Setup windows for DDR banks. Count total DDR size on the fly. */ |
| size = 0; |
| for (i = 0; i < dram->num_cs; i++) { |
| const struct mbus_dram_window *cs = dram->cs + i; |
| |
| writel(cs->base & 0xffff0000, |
| pcie->base + PCIE_WIN04_BASE_OFF(i)); |
| writel(0, pcie->base + PCIE_WIN04_REMAP_OFF(i)); |
| writel(((cs->size - 1) & 0xffff0000) | |
| (cs->mbus_attr << 8) | |
| (dram->mbus_dram_target_id << 4) | 1, |
| pcie->base + PCIE_WIN04_CTRL_OFF(i)); |
| |
| size += cs->size; |
| } |
| |
| /* Round up 'size' to the nearest power of two. */ |
| if ((size & (size - 1)) != 0) |
| size = 1 << fls(size); |
| |
| /* Setup BAR[1] to all DRAM banks. */ |
| writel(dram->cs[0].base | 0xc, pcie->base + PCIE_BAR_LO_OFF(1)); |
| writel(0, pcie->base + PCIE_BAR_HI_OFF(1)); |
| writel(((size - 1) & 0xffff0000) | 0x1, |
| pcie->base + PCIE_BAR_CTRL_OFF(1)); |
| } |
| |
| static int mvebu_pcie_probe(struct udevice *dev) |
| { |
| struct mvebu_pcie *pcie = dev_get_plat(dev); |
| struct udevice *ctlr = pci_get_controller(dev); |
| struct pci_controller *hose = dev_get_uclass_priv(ctlr); |
| int bus = dev_seq(dev); |
| u32 reg; |
| |
| debug("%s: PCIe %d.%d - up, base %08x\n", __func__, |
| pcie->port, pcie->lane, (u32)pcie->base); |
| |
| /* Read Id info and local bus/dev */ |
| debug("direct conf read %08x, local bus %d, local dev %d\n", |
| readl(pcie->base), mvebu_pcie_get_local_bus_nr(pcie), |
| mvebu_pcie_get_local_dev_nr(pcie)); |
| |
| pcie->first_busno = bus; |
| pcie->local_dev = 1; |
| |
| mvebu_pcie_set_local_bus_nr(pcie, bus); |
| mvebu_pcie_set_local_dev_nr(pcie, pcie->local_dev); |
| |
| pcie->mem.start = (u32)mvebu_pcie_membase; |
| pcie->mem.end = pcie->mem.start + PCIE_MEM_SIZE - 1; |
| mvebu_pcie_membase += PCIE_MEM_SIZE; |
| |
| if (mvebu_mbus_add_window_by_id(pcie->mem_target, pcie->mem_attr, |
| (phys_addr_t)pcie->mem.start, |
| PCIE_MEM_SIZE)) { |
| printf("PCIe unable to add mbus window for mem at %08x+%08x\n", |
| (u32)pcie->mem.start, PCIE_MEM_SIZE); |
| } |
| |
| pcie->io.start = (u32)mvebu_pcie_iobase; |
| pcie->io.end = pcie->io.start + MBUS_PCI_IO_SIZE - 1; |
| mvebu_pcie_iobase += MBUS_PCI_IO_SIZE; |
| |
| if (mvebu_mbus_add_window_by_id(pcie->io_target, pcie->io_attr, |
| (phys_addr_t)pcie->io.start, |
| MBUS_PCI_IO_SIZE)) { |
| printf("PCIe unable to add mbus window for IO at %08x+%08x\n", |
| (u32)pcie->io.start, MBUS_PCI_IO_SIZE); |
| } |
| |
| /* Setup windows and configure host bridge */ |
| mvebu_pcie_setup_wins(pcie); |
| |
| /* Master + slave enable. */ |
| reg = readl(pcie->base + PCIE_CMD_OFF); |
| reg |= PCI_COMMAND_MEMORY; |
| reg |= PCI_COMMAND_IO; |
| reg |= PCI_COMMAND_MASTER; |
| reg |= BIT(10); /* disable interrupts */ |
| writel(reg, pcie->base + PCIE_CMD_OFF); |
| |
| /* PCI memory space */ |
| pci_set_region(hose->regions + 0, pcie->mem.start, |
| pcie->mem.start, PCIE_MEM_SIZE, PCI_REGION_MEM); |
| pci_set_region(hose->regions + 1, |
| 0, 0, |
| gd->ram_size, |
| PCI_REGION_MEM | PCI_REGION_SYS_MEMORY); |
| pci_set_region(hose->regions + 2, pcie->io.start, |
| pcie->io.start, MBUS_PCI_IO_SIZE, PCI_REGION_IO); |
| hose->region_count = 3; |
| |
| /* Set BAR0 to internal registers */ |
| writel(SOC_REGS_PHY_BASE, pcie->base + PCIE_BAR_LO_OFF(0)); |
| writel(0, pcie->base + PCIE_BAR_HI_OFF(0)); |
| |
| return 0; |
| } |
| |
| static int mvebu_pcie_port_parse_dt(ofnode node, struct mvebu_pcie *pcie) |
| { |
| const u32 *addr; |
| int len; |
| |
| addr = ofnode_get_property(node, "assigned-addresses", &len); |
| if (!addr) { |
| pr_err("property \"assigned-addresses\" not found"); |
| return -FDT_ERR_NOTFOUND; |
| } |
| |
| pcie->base = (void *)(fdt32_to_cpu(addr[2]) + SOC_REGS_PHY_BASE); |
| |
| return 0; |
| } |
| |
| #define DT_FLAGS_TO_TYPE(flags) (((flags) >> 24) & 0x03) |
| #define DT_TYPE_IO 0x1 |
| #define DT_TYPE_MEM32 0x2 |
| #define DT_CPUADDR_TO_TARGET(cpuaddr) (((cpuaddr) >> 56) & 0xFF) |
| #define DT_CPUADDR_TO_ATTR(cpuaddr) (((cpuaddr) >> 48) & 0xFF) |
| |
| static int mvebu_get_tgt_attr(ofnode node, int devfn, |
| unsigned long type, |
| unsigned int *tgt, |
| unsigned int *attr) |
| { |
| const int na = 3, ns = 2; |
| const __be32 *range; |
| int rlen, nranges, rangesz, pna, i; |
| |
| *tgt = -1; |
| *attr = -1; |
| |
| range = ofnode_get_property(node, "ranges", &rlen); |
| if (!range) |
| return -EINVAL; |
| |
| /* |
| * Linux uses of_n_addr_cells() to get the number of address cells |
| * here. Currently this function is only available in U-Boot when |
| * CONFIG_OF_LIVE is enabled. Until this is enabled for MVEBU in |
| * general, lets't hardcode the "pna" value in the U-Boot code. |
| */ |
| pna = 2; /* hardcoded for now because of lack of of_n_addr_cells() */ |
| rangesz = pna + na + ns; |
| nranges = rlen / sizeof(__be32) / rangesz; |
| |
| for (i = 0; i < nranges; i++, range += rangesz) { |
| u32 flags = of_read_number(range, 1); |
| u32 slot = of_read_number(range + 1, 1); |
| u64 cpuaddr = of_read_number(range + na, pna); |
| unsigned long rtype; |
| |
| if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_IO) |
| rtype = IORESOURCE_IO; |
| else if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_MEM32) |
| rtype = IORESOURCE_MEM; |
| else |
| continue; |
| |
| /* |
| * The Linux code used PCI_SLOT() here, which expects devfn |
| * in bits 7..0. PCI_DEV() in U-Boot is similar to PCI_SLOT(), |
| * only expects devfn in 15..8, where its saved in this driver. |
| */ |
| if (slot == PCI_DEV(devfn) && type == rtype) { |
| *tgt = DT_CPUADDR_TO_TARGET(cpuaddr); |
| *attr = DT_CPUADDR_TO_ATTR(cpuaddr); |
| return 0; |
| } |
| } |
| |
| return -ENOENT; |
| } |
| |
| static int mvebu_pcie_of_to_plat(struct udevice *dev) |
| { |
| struct mvebu_pcie *pcie = dev_get_plat(dev); |
| int ret = 0; |
| |
| /* Get port number, lane number and memory target / attr */ |
| if (ofnode_read_u32(dev_ofnode(dev), "marvell,pcie-port", |
| &pcie->port)) { |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| if (ofnode_read_u32(dev_ofnode(dev), "marvell,pcie-lane", &pcie->lane)) |
| pcie->lane = 0; |
| |
| sprintf(pcie->name, "pcie%d.%d", pcie->port, pcie->lane); |
| |
| /* pci_get_devfn() returns devfn in bits 15..8, see PCI_DEV usage */ |
| pcie->devfn = pci_get_devfn(dev); |
| if (pcie->devfn < 0) { |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| ret = mvebu_get_tgt_attr(dev_ofnode(dev->parent), pcie->devfn, |
| IORESOURCE_MEM, |
| &pcie->mem_target, &pcie->mem_attr); |
| if (ret < 0) { |
| printf("%s: cannot get tgt/attr for mem window\n", pcie->name); |
| goto err; |
| } |
| |
| ret = mvebu_get_tgt_attr(dev_ofnode(dev->parent), pcie->devfn, |
| IORESOURCE_IO, |
| &pcie->io_target, &pcie->io_attr); |
| if (ret < 0) { |
| printf("%s: cannot get tgt/attr for IO window\n", pcie->name); |
| goto err; |
| } |
| |
| /* Parse PCIe controller register base from DT */ |
| ret = mvebu_pcie_port_parse_dt(dev_ofnode(dev), pcie); |
| if (ret < 0) |
| goto err; |
| |
| /* Check link and skip ports that have no link */ |
| if (!mvebu_pcie_link_up(pcie)) { |
| debug("%s: %s - down\n", __func__, pcie->name); |
| ret = -ENODEV; |
| goto err; |
| } |
| |
| return 0; |
| |
| err: |
| return ret; |
| } |
| |
| static const struct dm_pci_ops mvebu_pcie_ops = { |
| .read_config = mvebu_pcie_read_config, |
| .write_config = mvebu_pcie_write_config, |
| }; |
| |
| static struct driver pcie_mvebu_drv = { |
| .name = "pcie_mvebu", |
| .id = UCLASS_PCI, |
| .ops = &mvebu_pcie_ops, |
| .probe = mvebu_pcie_probe, |
| .of_to_plat = mvebu_pcie_of_to_plat, |
| .plat_auto = sizeof(struct mvebu_pcie), |
| }; |
| |
| /* |
| * Use a MISC device to bind the n instances (child nodes) of the |
| * PCIe base controller in UCLASS_PCI. |
| */ |
| static int mvebu_pcie_bind(struct udevice *parent) |
| { |
| struct mvebu_pcie *pcie; |
| struct uclass_driver *drv; |
| struct udevice *dev; |
| ofnode subnode; |
| |
| /* Lookup eth driver */ |
| drv = lists_uclass_lookup(UCLASS_PCI); |
| if (!drv) { |
| puts("Cannot find PCI driver\n"); |
| return -ENOENT; |
| } |
| |
| ofnode_for_each_subnode(subnode, dev_ofnode(parent)) { |
| if (!ofnode_is_available(subnode)) |
| continue; |
| |
| pcie = calloc(1, sizeof(*pcie)); |
| if (!pcie) |
| return -ENOMEM; |
| |
| /* Create child device UCLASS_PCI and bind it */ |
| device_bind(parent, &pcie_mvebu_drv, pcie->name, pcie, subnode, |
| &dev); |
| } |
| |
| return 0; |
| } |
| |
| static const struct udevice_id mvebu_pcie_ids[] = { |
| { .compatible = "marvell,armada-xp-pcie" }, |
| { .compatible = "marvell,armada-370-pcie" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(pcie_mvebu_base) = { |
| .name = "pcie_mvebu_base", |
| .id = UCLASS_MISC, |
| .of_match = mvebu_pcie_ids, |
| .bind = mvebu_pcie_bind, |
| }; |