| /* Copyright (c) 2018 The Chromium OS Authors. All rights reserved. |
| * Use of this source code is governed by a BSD-style license that can be |
| * found in the LICENSE file. |
| */ |
| |
| /* Host communication command constants for Chrome EC */ |
| |
| #ifndef __CROS_EC_COMMANDS_H |
| #define __CROS_EC_COMMANDS_H |
| |
| /* |
| * Protocol overview |
| * |
| * request: CMD [ P0 P1 P2 ... Pn S ] |
| * response: ERR [ P0 P1 P2 ... Pn S ] |
| * |
| * where the bytes are defined as follow : |
| * - CMD is the command code. (defined by EC_CMD_ constants) |
| * - ERR is the error code. (defined by EC_RES_ constants) |
| * - Px is the optional payload. |
| * it is not sent if the error code is not success. |
| * (defined by ec_params_ and ec_response_ structures) |
| * - S is the checksum which is the sum of all payload bytes. |
| * |
| * On LPC, CMD and ERR are sent/received at EC_LPC_ADDR_KERNEL|USER_CMD |
| * and the payloads are sent/received at EC_LPC_ADDR_KERNEL|USER_PARAM. |
| * On I2C, all bytes are sent serially in the same message. |
| */ |
| |
| /* |
| * Current version of this protocol |
| * |
| * TODO(crosbug.com/p/11223): This is effectively useless; protocol is |
| * determined in other ways. Remove this once the kernel code no longer |
| * depends on it. |
| */ |
| #define EC_PROTO_VERSION 0x00000002 |
| |
| /* Command version mask */ |
| #define EC_VER_MASK(version) (1UL << (version)) |
| |
| /* I/O addresses for ACPI commands */ |
| #define EC_LPC_ADDR_ACPI_DATA 0x62 |
| #define EC_LPC_ADDR_ACPI_CMD 0x66 |
| |
| /* I/O addresses for host command */ |
| #define EC_LPC_ADDR_HOST_DATA 0x200 |
| #define EC_LPC_ADDR_HOST_CMD 0x204 |
| |
| /* I/O addresses for host command args and params */ |
| /* Protocol version 2 */ |
| #define EC_LPC_ADDR_HOST_ARGS 0x800 /* And 0x801, 0x802, 0x803 */ |
| #define EC_LPC_ADDR_HOST_PARAM 0x804 /* For version 2 params; size is |
| * EC_PROTO2_MAX_PARAM_SIZE */ |
| /* Protocol version 3 */ |
| #define EC_LPC_ADDR_HOST_PACKET 0x800 /* Offset of version 3 packet */ |
| #define EC_LPC_HOST_PACKET_SIZE 0x100 /* Max size of version 3 packet */ |
| |
| /* The actual block is 0x800-0x8ff, but some BIOSes think it's 0x880-0x8ff |
| * and they tell the kernel that so we have to think of it as two parts. */ |
| #define EC_HOST_CMD_REGION0 0x800 |
| #define EC_HOST_CMD_REGION1 0x880 |
| #define EC_HOST_CMD_REGION_SIZE 0x80 |
| |
| /* EC command register bit functions */ |
| #define EC_LPC_CMDR_DATA (1 << 0) /* Data ready for host to read */ |
| #define EC_LPC_CMDR_PENDING (1 << 1) /* Write pending to EC */ |
| #define EC_LPC_CMDR_BUSY (1 << 2) /* EC is busy processing a command */ |
| #define EC_LPC_CMDR_CMD (1 << 3) /* Last host write was a command */ |
| #define EC_LPC_CMDR_ACPI_BRST (1 << 4) /* Burst mode (not used) */ |
| #define EC_LPC_CMDR_SCI (1 << 5) /* SCI event is pending */ |
| #define EC_LPC_CMDR_SMI (1 << 6) /* SMI event is pending */ |
| |
| /* MEC uses 0x800/0x804 as register/index pair, thus an 8-byte resource */ |
| #define MEC_EMI_BASE 0x800 |
| #define MEC_EMI_SIZE 8 |
| |
| #define EC_LPC_ADDR_MEMMAP 0x900 |
| #define EC_MEMMAP_SIZE 255 /* ACPI IO buffer max is 255 bytes */ |
| #define EC_MEMMAP_TEXT_MAX 8 /* Size of a string in the memory map */ |
| |
| /* The offset address of each type of data in mapped memory. */ |
| #define EC_MEMMAP_TEMP_SENSOR 0x00 /* Temp sensors 0x00 - 0x0f */ |
| #define EC_MEMMAP_FAN 0x10 /* Fan speeds 0x10 - 0x17 */ |
| #define EC_MEMMAP_TEMP_SENSOR_B 0x18 /* More temp sensors 0x18 - 0x1f */ |
| #define EC_MEMMAP_ID 0x20 /* 0x20 == 'E', 0x21 == 'C' */ |
| #define EC_MEMMAP_ID_VERSION 0x22 /* Version of data in 0x20 - 0x2f */ |
| #define EC_MEMMAP_THERMAL_VERSION 0x23 /* Version of data in 0x00 - 0x1f */ |
| #define EC_MEMMAP_BATTERY_VERSION 0x24 /* Version of data in 0x40 - 0x7f */ |
| #define EC_MEMMAP_SWITCHES_VERSION 0x25 /* Version of data in 0x30 - 0x33 */ |
| #define EC_MEMMAP_EVENTS_VERSION 0x26 /* Version of data in 0x34 - 0x3f */ |
| #define EC_MEMMAP_HOST_CMD_FLAGS 0x27 /* Host cmd interface flags (8 bits) */ |
| /* Unused 0x28 - 0x2f */ |
| #define EC_MEMMAP_SWITCHES 0x30 /* 8 bits */ |
| /* Unused 0x31 - 0x33 */ |
| #define EC_MEMMAP_HOST_EVENTS 0x34 /* 32 bits */ |
| /* Reserve 0x38 - 0x3f for additional host event-related stuff */ |
| /* Battery values are all 32 bits */ |
| #define EC_MEMMAP_BATT_VOLT 0x40 /* Battery Present Voltage */ |
| #define EC_MEMMAP_BATT_RATE 0x44 /* Battery Present Rate */ |
| #define EC_MEMMAP_BATT_CAP 0x48 /* Battery Remaining Capacity */ |
| #define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, defined below */ |
| #define EC_MEMMAP_BATT_DCAP 0x50 /* Battery Design Capacity */ |
| #define EC_MEMMAP_BATT_DVLT 0x54 /* Battery Design Voltage */ |
| #define EC_MEMMAP_BATT_LFCC 0x58 /* Battery Last Full Charge Capacity */ |
| #define EC_MEMMAP_BATT_CCNT 0x5c /* Battery Cycle Count */ |
| /* Strings are all 8 bytes (EC_MEMMAP_TEXT_MAX) */ |
| #define EC_MEMMAP_BATT_MFGR 0x60 /* Battery Manufacturer String */ |
| #define EC_MEMMAP_BATT_MODEL 0x68 /* Battery Model Number String */ |
| #define EC_MEMMAP_BATT_SERIAL 0x70 /* Battery Serial Number String */ |
| #define EC_MEMMAP_BATT_TYPE 0x78 /* Battery Type String */ |
| #define EC_MEMMAP_ALS 0x80 /* ALS readings in lux (2 X 16 bits) */ |
| /* Unused 0x84 - 0x8f */ |
| #define EC_MEMMAP_ACC_STATUS 0x90 /* Accelerometer status (8 bits )*/ |
| /* Unused 0x91 */ |
| #define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometers data 0x92 - 0x9f */ |
| /* 0x92: Lid Angle if available, LID_ANGLE_UNRELIABLE otherwise */ |
| /* 0x94 - 0x99: 1st Accelerometer */ |
| /* 0x9a - 0x9f: 2nd Accelerometer */ |
| #define EC_MEMMAP_GYRO_DATA 0xa0 /* Gyroscope data 0xa0 - 0xa5 */ |
| /* Unused 0xa6 - 0xdf */ |
| |
| /* |
| * ACPI is unable to access memory mapped data at or above this offset due to |
| * limitations of the ACPI protocol. Do not place data in the range 0xe0 - 0xfe |
| * which might be needed by ACPI. |
| */ |
| #define EC_MEMMAP_NO_ACPI 0xe0 |
| |
| /* Define the format of the accelerometer mapped memory status byte. */ |
| #define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK 0x0f |
| #define EC_MEMMAP_ACC_STATUS_BUSY_BIT (1 << 4) |
| #define EC_MEMMAP_ACC_STATUS_PRESENCE_BIT (1 << 7) |
| |
| /* Number of temp sensors at EC_MEMMAP_TEMP_SENSOR */ |
| #define EC_TEMP_SENSOR_ENTRIES 16 |
| /* |
| * Number of temp sensors at EC_MEMMAP_TEMP_SENSOR_B. |
| * |
| * Valid only if EC_MEMMAP_THERMAL_VERSION returns >= 2. |
| */ |
| #define EC_TEMP_SENSOR_B_ENTRIES 8 |
| |
| /* Special values for mapped temperature sensors */ |
| #define EC_TEMP_SENSOR_NOT_PRESENT 0xff |
| #define EC_TEMP_SENSOR_ERROR 0xfe |
| #define EC_TEMP_SENSOR_NOT_POWERED 0xfd |
| #define EC_TEMP_SENSOR_NOT_CALIBRATED 0xfc |
| /* |
| * The offset of temperature value stored in mapped memory. This allows |
| * reporting a temperature range of 200K to 454K = -73C to 181C. |
| */ |
| #define EC_TEMP_SENSOR_OFFSET 200 |
| |
| /* |
| * Number of ALS readings at EC_MEMMAP_ALS |
| */ |
| #define EC_ALS_ENTRIES 2 |
| |
| /* |
| * The default value a temperature sensor will return when it is present but |
| * has not been read this boot. This is a reasonable number to avoid |
| * triggering alarms on the host. |
| */ |
| #define EC_TEMP_SENSOR_DEFAULT (296 - EC_TEMP_SENSOR_OFFSET) |
| |
| #define EC_FAN_SPEED_ENTRIES 4 /* Number of fans at EC_MEMMAP_FAN */ |
| #define EC_FAN_SPEED_NOT_PRESENT 0xffff /* Entry not present */ |
| #define EC_FAN_SPEED_STALLED 0xfffe /* Fan stalled */ |
| |
| /* Battery bit flags at EC_MEMMAP_BATT_FLAG. */ |
| #define EC_BATT_FLAG_AC_PRESENT 0x01 |
| #define EC_BATT_FLAG_BATT_PRESENT 0x02 |
| #define EC_BATT_FLAG_DISCHARGING 0x04 |
| #define EC_BATT_FLAG_CHARGING 0x08 |
| #define EC_BATT_FLAG_LEVEL_CRITICAL 0x10 |
| |
| /* Switch flags at EC_MEMMAP_SWITCHES */ |
| #define EC_SWITCH_LID_OPEN 0x01 |
| #define EC_SWITCH_POWER_BUTTON_PRESSED 0x02 |
| #define EC_SWITCH_WRITE_PROTECT_DISABLED 0x04 |
| /* Was recovery requested via keyboard; now unused. */ |
| #define EC_SWITCH_IGNORE1 0x08 |
| /* Recovery requested via dedicated signal (from servo board) */ |
| #define EC_SWITCH_DEDICATED_RECOVERY 0x10 |
| /* Was fake developer mode switch; now unused. Remove in next refactor. */ |
| #define EC_SWITCH_IGNORE0 0x20 |
| |
| /* Host command interface flags */ |
| /* Host command interface supports LPC args (LPC interface only) */ |
| #define EC_HOST_CMD_FLAG_LPC_ARGS_SUPPORTED 0x01 |
| /* Host command interface supports version 3 protocol */ |
| #define EC_HOST_CMD_FLAG_VERSION_3 0x02 |
| |
| /* Wireless switch flags */ |
| #define EC_WIRELESS_SWITCH_ALL ~0x00 /* All flags */ |
| #define EC_WIRELESS_SWITCH_WLAN 0x01 /* WLAN radio */ |
| #define EC_WIRELESS_SWITCH_BLUETOOTH 0x02 /* Bluetooth radio */ |
| #define EC_WIRELESS_SWITCH_WWAN 0x04 /* WWAN power */ |
| #define EC_WIRELESS_SWITCH_WLAN_POWER 0x08 /* WLAN power */ |
| |
| /*****************************************************************************/ |
| /* |
| * ACPI commands |
| * |
| * These are valid ONLY on the ACPI command/data port. |
| */ |
| |
| /* |
| * ACPI Read Embedded Controller |
| * |
| * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). |
| * |
| * Use the following sequence: |
| * |
| * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD |
| * - Wait for EC_LPC_CMDR_PENDING bit to clear |
| * - Write address to EC_LPC_ADDR_ACPI_DATA |
| * - Wait for EC_LPC_CMDR_DATA bit to set |
| * - Read value from EC_LPC_ADDR_ACPI_DATA |
| */ |
| #define EC_CMD_ACPI_READ 0x0080 |
| |
| /* |
| * ACPI Write Embedded Controller |
| * |
| * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). |
| * |
| * Use the following sequence: |
| * |
| * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD |
| * - Wait for EC_LPC_CMDR_PENDING bit to clear |
| * - Write address to EC_LPC_ADDR_ACPI_DATA |
| * - Wait for EC_LPC_CMDR_PENDING bit to clear |
| * - Write value to EC_LPC_ADDR_ACPI_DATA |
| */ |
| #define EC_CMD_ACPI_WRITE 0x0081 |
| |
| /* |
| * ACPI Burst Enable Embedded Controller |
| * |
| * This enables burst mode on the EC to allow the host to issue several |
| * commands back-to-back. While in this mode, writes to mapped multi-byte |
| * data are locked out to ensure data consistency. |
| */ |
| #define EC_CMD_ACPI_BURST_ENABLE 0x0082 |
| |
| /* |
| * ACPI Burst Disable Embedded Controller |
| * |
| * This disables burst mode on the EC and stops preventing EC writes to mapped |
| * multi-byte data. |
| */ |
| #define EC_CMD_ACPI_BURST_DISABLE 0x0083 |
| |
| /* |
| * ACPI Query Embedded Controller |
| * |
| * This clears the lowest-order bit in the currently pending host events, and |
| * sets the result code to the 1-based index of the bit (event 0x00000001 = 1, |
| * event 0x80000000 = 32), or 0 if no event was pending. |
| */ |
| #define EC_CMD_ACPI_QUERY_EVENT 0x0084 |
| |
| /* Valid addresses in ACPI memory space, for read/write commands */ |
| |
| /* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */ |
| #define EC_ACPI_MEM_VERSION 0x00 |
| /* |
| * Test location; writing value here updates test compliment byte to (0xff - |
| * value). |
| */ |
| #define EC_ACPI_MEM_TEST 0x01 |
| /* Test compliment; writes here are ignored. */ |
| #define EC_ACPI_MEM_TEST_COMPLIMENT 0x02 |
| |
| /* Keyboard backlight brightness percent (0 - 100) */ |
| #define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03 |
| /* DPTF Target Fan Duty (0-100, 0xff for auto/none) */ |
| #define EC_ACPI_MEM_FAN_DUTY 0x04 |
| |
| /* |
| * DPTF temp thresholds. Any of the EC's temp sensors can have up to two |
| * independent thresholds attached to them. The current value of the ID |
| * register determines which sensor is affected by the THRESHOLD and COMMIT |
| * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme |
| * as the memory-mapped sensors. The COMMIT register applies those settings. |
| * |
| * The spec does not mandate any way to read back the threshold settings |
| * themselves, but when a threshold is crossed the AP needs a way to determine |
| * which sensor(s) are responsible. Each reading of the ID register clears and |
| * returns one sensor ID that has crossed one of its threshold (in either |
| * direction) since the last read. A value of 0xFF means "no new thresholds |
| * have tripped". Setting or enabling the thresholds for a sensor will clear |
| * the unread event count for that sensor. |
| */ |
| #define EC_ACPI_MEM_TEMP_ID 0x05 |
| #define EC_ACPI_MEM_TEMP_THRESHOLD 0x06 |
| #define EC_ACPI_MEM_TEMP_COMMIT 0x07 |
| /* |
| * Here are the bits for the COMMIT register: |
| * bit 0 selects the threshold index for the chosen sensor (0/1) |
| * bit 1 enables/disables the selected threshold (0 = off, 1 = on) |
| * Each write to the commit register affects one threshold. |
| */ |
| #define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0) |
| #define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1) |
| /* |
| * Example: |
| * |
| * Set the thresholds for sensor 2 to 50 C and 60 C: |
| * write 2 to [0x05] -- select temp sensor 2 |
| * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET |
| * write 0x2 to [0x07] -- enable threshold 0 with this value |
| * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET |
| * write 0x3 to [0x07] -- enable threshold 1 with this value |
| * |
| * Disable the 60 C threshold, leaving the 50 C threshold unchanged: |
| * write 2 to [0x05] -- select temp sensor 2 |
| * write 0x1 to [0x07] -- disable threshold 1 |
| */ |
| |
| /* DPTF battery charging current limit */ |
| #define EC_ACPI_MEM_CHARGING_LIMIT 0x08 |
| |
| /* Charging limit is specified in 64 mA steps */ |
| #define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64 |
| /* Value to disable DPTF battery charging limit */ |
| #define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff |
| |
| /* |
| * Report device orientation |
| * bit 0 device is tablet mode |
| */ |
| #define EC_ACPI_MEM_DEVICE_ORIENTATION 0x09 |
| #define EC_ACPI_MEM_DEVICE_TABLET_MODE 0x01 |
| |
| /* |
| * ACPI addresses 0x20 - 0xff map to EC_MEMMAP offset 0x00 - 0xdf. This data |
| * is read-only from the AP. Added in EC_ACPI_MEM_VERSION 2. |
| */ |
| #define EC_ACPI_MEM_MAPPED_BEGIN 0x20 |
| #define EC_ACPI_MEM_MAPPED_SIZE 0xe0 |
| |
| /* Current version of ACPI memory address space */ |
| #define EC_ACPI_MEM_VERSION_CURRENT 2 |
| |
| |
| /* |
| * This header file is used in coreboot both in C and ACPI code. The ACPI code |
| * is pre-processed to handle constants but the ASL compiler is unable to |
| * handle actual C code so keep it separate. |
| */ |
| #ifndef __ACPI__ |
| |
| /* |
| * Define __packed if someone hasn't beat us to it. Linux kernel style |
| * checking prefers __packed over __attribute__((packed)). |
| */ |
| #ifndef __packed |
| #define __packed __attribute__((packed)) |
| #endif |
| |
| #ifndef __aligned |
| #define __aligned(x) __attribute__((aligned(x))) |
| #endif |
| |
| /* |
| * Attributes for EC request and response packets. Just defining __packed |
| * results in inefficient assembly code on ARM, if the structure is actually |
| * 32-bit aligned, as it should be for all buffers. |
| * |
| * Be very careful when adding these to existing structures. They will round |
| * up the structure size to the specified boundary. |
| * |
| * Also be very careful to make that if a structure is included in some other |
| * parent structure that the alignment will still be true given the packing of |
| * the parent structure. This is particularly important if the sub-structure |
| * will be passed as a pointer to another function, since that function will |
| * not know about the misaligment caused by the parent structure's packing. |
| * |
| * Also be very careful using __packed - particularly when nesting non-packed |
| * structures inside packed ones. In fact, DO NOT use __packed directly; |
| * always use one of these attributes. |
| * |
| * Once everything is annotated properly, the following search strings should |
| * not return ANY matches in this file other than right here: |
| * |
| * "__packed" - generates inefficient code; all sub-structs must also be packed |
| * |
| * "struct [^_]" - all structs should be annotated, except for structs that are |
| * members of other structs/unions (and their original declarations should be |
| * annotated). |
| */ |
| #ifdef CONFIG_HOSTCMD_ALIGNED |
| |
| /* |
| * Packed structures where offset and size are always aligned to 1, 2, or 4 |
| * byte boundary. |
| */ |
| #define __ec_align1 __packed |
| #define __ec_align2 __packed __aligned(2) |
| #define __ec_align4 __packed __aligned(4) |
| |
| /* |
| * Packed structure which must be under-aligned, because its size is not a |
| * 4-byte multiple. This is sub-optimal because it forces byte-wise access |
| * of all multi-byte fields in it, even though they are themselves aligned. |
| * |
| * In theory, we could duplicate the structure with __aligned(4) for accessing |
| * its members, but use the __packed version for sizeof(). |
| */ |
| #define __ec_align_size1 __packed |
| |
| /* |
| * Packed structure which must be under-aligned, because its offset inside a |
| * parent structure is not a 4-byte multiple. |
| */ |
| #define __ec_align_offset1 __packed |
| #define __ec_align_offset2 __packed __aligned(2) |
| |
| /* |
| * Structures which are complicated enough that I'm skipping them on the first |
| * pass. They are effectively unchanged from their previous definitions. |
| * |
| * TODO(rspangler): Figure out what to do with these. It's likely necessary |
| * to work out the size and offset of each member and add explicit padding to |
| * maintain those. |
| */ |
| #define __ec_todo_packed __packed |
| #define __ec_todo_unpacked |
| |
| #else /* !CONFIG_HOSTCMD_ALIGNED */ |
| |
| /* |
| * Packed structures make no assumption about alignment, so they do inefficient |
| * byte-wise reads. |
| */ |
| #define __ec_align1 __packed |
| #define __ec_align2 __packed |
| #define __ec_align4 __packed |
| #define __ec_align_size1 __packed |
| #define __ec_align_offset1 __packed |
| #define __ec_align_offset2 __packed |
| #define __ec_todo_packed __packed |
| #define __ec_todo_unpacked |
| |
| #endif /* !CONFIG_HOSTCMD_ALIGNED */ |
| |
| /* LPC command status byte masks */ |
| /* EC has written a byte in the data register and host hasn't read it yet */ |
| #define EC_LPC_STATUS_TO_HOST 0x01 |
| /* Host has written a command/data byte and the EC hasn't read it yet */ |
| #define EC_LPC_STATUS_FROM_HOST 0x02 |
| /* EC is processing a command */ |
| #define EC_LPC_STATUS_PROCESSING 0x04 |
| /* Last write to EC was a command, not data */ |
| #define EC_LPC_STATUS_LAST_CMD 0x08 |
| /* EC is in burst mode */ |
| #define EC_LPC_STATUS_BURST_MODE 0x10 |
| /* SCI event is pending (requesting SCI query) */ |
| #define EC_LPC_STATUS_SCI_PENDING 0x20 |
| /* SMI event is pending (requesting SMI query) */ |
| #define EC_LPC_STATUS_SMI_PENDING 0x40 |
| /* (reserved) */ |
| #define EC_LPC_STATUS_RESERVED 0x80 |
| |
| /* |
| * EC is busy. This covers both the EC processing a command, and the host has |
| * written a new command but the EC hasn't picked it up yet. |
| */ |
| #define EC_LPC_STATUS_BUSY_MASK \ |
| (EC_LPC_STATUS_FROM_HOST | EC_LPC_STATUS_PROCESSING) |
| |
| /* Host command response codes (16-bit). Note that response codes should be |
| * stored in a uint16_t rather than directly in a value of this type. |
| */ |
| enum ec_status { |
| EC_RES_SUCCESS = 0, |
| EC_RES_INVALID_COMMAND = 1, |
| EC_RES_ERROR = 2, |
| EC_RES_INVALID_PARAM = 3, |
| EC_RES_ACCESS_DENIED = 4, |
| EC_RES_INVALID_RESPONSE = 5, |
| EC_RES_INVALID_VERSION = 6, |
| EC_RES_INVALID_CHECKSUM = 7, |
| EC_RES_IN_PROGRESS = 8, /* Accepted, command in progress */ |
| EC_RES_UNAVAILABLE = 9, /* No response available */ |
| EC_RES_TIMEOUT = 10, /* We got a timeout */ |
| EC_RES_OVERFLOW = 11, /* Table / data overflow */ |
| EC_RES_INVALID_HEADER = 12, /* Header contains invalid data */ |
| EC_RES_REQUEST_TRUNCATED = 13, /* Didn't get the entire request */ |
| EC_RES_RESPONSE_TOO_BIG = 14, /* Response was too big to handle */ |
| EC_RES_BUS_ERROR = 15, /* Communications bus error */ |
| EC_RES_BUSY = 16 /* Up but too busy. Should retry */ |
| }; |
| |
| /* |
| * Host event codes. Note these are 1-based, not 0-based, because ACPI query |
| * EC command uses code 0 to mean "no event pending". We explicitly specify |
| * each value in the enum listing so they won't change if we delete/insert an |
| * item or rearrange the list (it needs to be stable across platforms, not |
| * just within a single compiled instance). |
| */ |
| enum host_event_code { |
| EC_HOST_EVENT_LID_CLOSED = 1, |
| EC_HOST_EVENT_LID_OPEN = 2, |
| EC_HOST_EVENT_POWER_BUTTON = 3, |
| EC_HOST_EVENT_AC_CONNECTED = 4, |
| EC_HOST_EVENT_AC_DISCONNECTED = 5, |
| EC_HOST_EVENT_BATTERY_LOW = 6, |
| EC_HOST_EVENT_BATTERY_CRITICAL = 7, |
| EC_HOST_EVENT_BATTERY = 8, |
| EC_HOST_EVENT_THERMAL_THRESHOLD = 9, |
| /* Event generated by a device attached to the EC */ |
| EC_HOST_EVENT_DEVICE = 10, |
| EC_HOST_EVENT_THERMAL = 11, |
| EC_HOST_EVENT_USB_CHARGER = 12, |
| EC_HOST_EVENT_KEY_PRESSED = 13, |
| /* |
| * EC has finished initializing the host interface. The host can check |
| * for this event following sending a EC_CMD_REBOOT_EC command to |
| * determine when the EC is ready to accept subsequent commands. |
| */ |
| EC_HOST_EVENT_INTERFACE_READY = 14, |
| /* Keyboard recovery combo has been pressed */ |
| EC_HOST_EVENT_KEYBOARD_RECOVERY = 15, |
| |
| /* Shutdown due to thermal overload */ |
| EC_HOST_EVENT_THERMAL_SHUTDOWN = 16, |
| /* Shutdown due to battery level too low */ |
| EC_HOST_EVENT_BATTERY_SHUTDOWN = 17, |
| |
| /* Suggest that the AP throttle itself */ |
| EC_HOST_EVENT_THROTTLE_START = 18, |
| /* Suggest that the AP resume normal speed */ |
| EC_HOST_EVENT_THROTTLE_STOP = 19, |
| |
| /* Hang detect logic detected a hang and host event timeout expired */ |
| EC_HOST_EVENT_HANG_DETECT = 20, |
| /* Hang detect logic detected a hang and warm rebooted the AP */ |
| EC_HOST_EVENT_HANG_REBOOT = 21, |
| |
| /* PD MCU triggering host event */ |
| EC_HOST_EVENT_PD_MCU = 22, |
| |
| /* Battery Status flags have changed */ |
| EC_HOST_EVENT_BATTERY_STATUS = 23, |
| |
| /* EC encountered a panic, triggering a reset */ |
| EC_HOST_EVENT_PANIC = 24, |
| |
| /* Keyboard fastboot combo has been pressed */ |
| EC_HOST_EVENT_KEYBOARD_FASTBOOT = 25, |
| |
| /* EC RTC event occurred */ |
| EC_HOST_EVENT_RTC = 26, |
| |
| /* Emulate MKBP event */ |
| EC_HOST_EVENT_MKBP = 27, |
| |
| /* EC desires to change state of host-controlled USB mux */ |
| EC_HOST_EVENT_USB_MUX = 28, |
| |
| /* TABLET/LAPTOP mode event*/ |
| EC_HOST_EVENT_MODE_CHANGE = 29, |
| |
| /* Keyboard recovery combo with hardware reinitialization */ |
| EC_HOST_EVENT_KEYBOARD_RECOVERY_HW_REINIT = 30, |
| |
| /* |
| * Reserve this last bit to indicate that at least one bit in a |
| * secondary host event word is set. See crbug.com/633646. |
| */ |
| EC_HOST_EVENT_EXTENDED = 31, |
| |
| /* |
| * The high bit of the event mask is not used as a host event code. If |
| * it reads back as set, then the entire event mask should be |
| * considered invalid by the host. This can happen when reading the |
| * raw event status via EC_MEMMAP_HOST_EVENTS but the LPC interface is |
| * not initialized on the EC, or improperly configured on the host. |
| */ |
| EC_HOST_EVENT_INVALID = 32 |
| }; |
| /* Host event mask */ |
| #define EC_HOST_EVENT_MASK(event_code) (1ULL << ((event_code) - 1)) |
| |
| /* Arguments at EC_LPC_ADDR_HOST_ARGS */ |
| struct __ec_align4 ec_lpc_host_args { |
| uint8_t flags; |
| uint8_t command_version; |
| uint8_t data_size; |
| /* |
| * Checksum; sum of command + flags + command_version + data_size + |
| * all params/response data bytes. |
| */ |
| uint8_t checksum; |
| }; |
| |
| /* Flags for ec_lpc_host_args.flags */ |
| /* |
| * Args are from host. Data area at EC_LPC_ADDR_HOST_PARAM contains command |
| * params. |
| * |
| * If EC gets a command and this flag is not set, this is an old-style command. |
| * Command version is 0 and params from host are at EC_LPC_ADDR_OLD_PARAM with |
| * unknown length. EC must respond with an old-style response (that is, |
| * without setting EC_HOST_ARGS_FLAG_TO_HOST). |
| */ |
| #define EC_HOST_ARGS_FLAG_FROM_HOST 0x01 |
| /* |
| * Args are from EC. Data area at EC_LPC_ADDR_HOST_PARAM contains response. |
| * |
| * If EC responds to a command and this flag is not set, this is an old-style |
| * response. Command version is 0 and response data from EC is at |
| * EC_LPC_ADDR_OLD_PARAM with unknown length. |
| */ |
| #define EC_HOST_ARGS_FLAG_TO_HOST 0x02 |
| |
| /*****************************************************************************/ |
| /* |
| * Byte codes returned by EC over SPI interface. |
| * |
| * These can be used by the AP to debug the EC interface, and to determine |
| * when the EC is not in a state where it will ever get around to responding |
| * to the AP. |
| * |
| * Example of sequence of bytes read from EC for a current good transfer: |
| * 1. - - AP asserts chip select (CS#) |
| * 2. EC_SPI_OLD_READY - AP sends first byte(s) of request |
| * 3. - - EC starts handling CS# interrupt |
| * 4. EC_SPI_RECEIVING - AP sends remaining byte(s) of request |
| * 5. EC_SPI_PROCESSING - EC starts processing request; AP is clocking in |
| * bytes looking for EC_SPI_FRAME_START |
| * 6. - - EC finishes processing and sets up response |
| * 7. EC_SPI_FRAME_START - AP reads frame byte |
| * 8. (response packet) - AP reads response packet |
| * 9. EC_SPI_PAST_END - Any additional bytes read by AP |
| * 10 - - AP deasserts chip select |
| * 11 - - EC processes CS# interrupt and sets up DMA for |
| * next request |
| * |
| * If the AP is waiting for EC_SPI_FRAME_START and sees any value other than |
| * the following byte values: |
| * EC_SPI_OLD_READY |
| * EC_SPI_RX_READY |
| * EC_SPI_RECEIVING |
| * EC_SPI_PROCESSING |
| * |
| * Then the EC found an error in the request, or was not ready for the request |
| * and lost data. The AP should give up waiting for EC_SPI_FRAME_START, |
| * because the EC is unable to tell when the AP is done sending its request. |
| */ |
| |
| /* |
| * Framing byte which precedes a response packet from the EC. After sending a |
| * request, the AP will clock in bytes until it sees the framing byte, then |
| * clock in the response packet. |
| */ |
| #define EC_SPI_FRAME_START 0xec |
| |
| /* |
| * Padding bytes which are clocked out after the end of a response packet. |
| */ |
| #define EC_SPI_PAST_END 0xed |
| |
| /* |
| * EC is ready to receive, and has ignored the byte sent by the AP. EC expects |
| * that the AP will send a valid packet header (starting with |
| * EC_COMMAND_PROTOCOL_3) in the next 32 bytes. |
| */ |
| #define EC_SPI_RX_READY 0xf8 |
| |
| /* |
| * EC has started receiving the request from the AP, but hasn't started |
| * processing it yet. |
| */ |
| #define EC_SPI_RECEIVING 0xf9 |
| |
| /* EC has received the entire request from the AP and is processing it. */ |
| #define EC_SPI_PROCESSING 0xfa |
| |
| /* |
| * EC received bad data from the AP, such as a packet header with an invalid |
| * length. EC will ignore all data until chip select deasserts. |
| */ |
| #define EC_SPI_RX_BAD_DATA 0xfb |
| |
| /* |
| * EC received data from the AP before it was ready. That is, the AP asserted |
| * chip select and started clocking data before the EC was ready to receive it. |
| * EC will ignore all data until chip select deasserts. |
| */ |
| #define EC_SPI_NOT_READY 0xfc |
| |
| /* |
| * EC was ready to receive a request from the AP. EC has treated the byte sent |
| * by the AP as part of a request packet, or (for old-style ECs) is processing |
| * a fully received packet but is not ready to respond yet. |
| */ |
| #define EC_SPI_OLD_READY 0xfd |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Protocol version 2 for I2C and SPI send a request this way: |
| * |
| * 0 EC_CMD_VERSION0 + (command version) |
| * 1 Command number |
| * 2 Length of params = N |
| * 3..N+2 Params, if any |
| * N+3 8-bit checksum of bytes 0..N+2 |
| * |
| * The corresponding response is: |
| * |
| * 0 Result code (EC_RES_*) |
| * 1 Length of params = M |
| * 2..M+1 Params, if any |
| * M+2 8-bit checksum of bytes 0..M+1 |
| */ |
| #define EC_PROTO2_REQUEST_HEADER_BYTES 3 |
| #define EC_PROTO2_REQUEST_TRAILER_BYTES 1 |
| #define EC_PROTO2_REQUEST_OVERHEAD (EC_PROTO2_REQUEST_HEADER_BYTES + \ |
| EC_PROTO2_REQUEST_TRAILER_BYTES) |
| |
| #define EC_PROTO2_RESPONSE_HEADER_BYTES 2 |
| #define EC_PROTO2_RESPONSE_TRAILER_BYTES 1 |
| #define EC_PROTO2_RESPONSE_OVERHEAD (EC_PROTO2_RESPONSE_HEADER_BYTES + \ |
| EC_PROTO2_RESPONSE_TRAILER_BYTES) |
| |
| /* Parameter length was limited by the LPC interface */ |
| #define EC_PROTO2_MAX_PARAM_SIZE 0xfc |
| |
| /* Maximum request and response packet sizes for protocol version 2 */ |
| #define EC_PROTO2_MAX_REQUEST_SIZE (EC_PROTO2_REQUEST_OVERHEAD + \ |
| EC_PROTO2_MAX_PARAM_SIZE) |
| #define EC_PROTO2_MAX_RESPONSE_SIZE (EC_PROTO2_RESPONSE_OVERHEAD + \ |
| EC_PROTO2_MAX_PARAM_SIZE) |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Value written to legacy command port / prefix byte to indicate protocol |
| * 3+ structs are being used. Usage is bus-dependent. |
| */ |
| #define EC_COMMAND_PROTOCOL_3 0xda |
| |
| #define EC_HOST_REQUEST_VERSION 3 |
| |
| /* Version 3 request from host */ |
| struct __ec_align4 ec_host_request { |
| /* Structure version (=3) |
| * |
| * EC will return EC_RES_INVALID_HEADER if it receives a header with a |
| * version it doesn't know how to parse. |
| */ |
| uint8_t struct_version; |
| |
| /* |
| * Checksum of request and data; sum of all bytes including checksum |
| * should total to 0. |
| */ |
| uint8_t checksum; |
| |
| /* Command code */ |
| uint16_t command; |
| |
| /* Command version */ |
| uint8_t command_version; |
| |
| /* Unused byte in current protocol version; set to 0 */ |
| uint8_t reserved; |
| |
| /* Length of data which follows this header */ |
| uint16_t data_len; |
| }; |
| |
| #define EC_HOST_RESPONSE_VERSION 3 |
| |
| /* Version 3 response from EC */ |
| struct __ec_align4 ec_host_response { |
| /* Structure version (=3) */ |
| uint8_t struct_version; |
| |
| /* |
| * Checksum of response and data; sum of all bytes including checksum |
| * should total to 0. |
| */ |
| uint8_t checksum; |
| |
| /* Result code (EC_RES_*) */ |
| uint16_t result; |
| |
| /* Length of data which follows this header */ |
| uint16_t data_len; |
| |
| /* Unused bytes in current protocol version; set to 0 */ |
| uint16_t reserved; |
| }; |
| |
| /*****************************************************************************/ |
| /* |
| * Notes on commands: |
| * |
| * Each command is an 16-bit command value. Commands which take params or |
| * return response data specify structures for that data. If no structure is |
| * specified, the command does not input or output data, respectively. |
| * Parameter/response length is implicit in the structs. Some underlying |
| * communication protocols (I2C, SPI) may add length or checksum headers, but |
| * those are implementation-dependent and not defined here. |
| * |
| * All commands MUST be #defined to be 4-digit UPPER CASE hex values |
| * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work. |
| */ |
| |
| /*****************************************************************************/ |
| /* General / test commands */ |
| |
| /* |
| * Get protocol version, used to deal with non-backward compatible protocol |
| * changes. |
| */ |
| #define EC_CMD_PROTO_VERSION 0x0000 |
| |
| struct __ec_align4 ec_response_proto_version { |
| uint32_t version; |
| }; |
| |
| /* |
| * Hello. This is a simple command to test the EC is responsive to |
| * commands. |
| */ |
| #define EC_CMD_HELLO 0x0001 |
| |
| struct __ec_align4 ec_params_hello { |
| uint32_t in_data; /* Pass anything here */ |
| }; |
| |
| struct __ec_align4 ec_response_hello { |
| uint32_t out_data; /* Output will be in_data + 0x01020304 */ |
| }; |
| |
| /* Get version number */ |
| #define EC_CMD_GET_VERSION 0x0002 |
| |
| enum ec_current_image { |
| EC_IMAGE_UNKNOWN = 0, |
| EC_IMAGE_RO, |
| EC_IMAGE_RW |
| }; |
| |
| struct __ec_align4 ec_response_get_version { |
| /* Null-terminated version strings for RO, RW */ |
| char version_string_ro[32]; |
| char version_string_rw[32]; |
| char reserved[32]; /* Was previously RW-B string */ |
| uint32_t current_image; /* One of ec_current_image */ |
| }; |
| |
| /* Read test */ |
| #define EC_CMD_READ_TEST 0x0003 |
| |
| struct __ec_align4 ec_params_read_test { |
| uint32_t offset; /* Starting value for read buffer */ |
| uint32_t size; /* Size to read in bytes */ |
| }; |
| |
| struct __ec_align4 ec_response_read_test { |
| uint32_t data[32]; |
| }; |
| |
| /* |
| * Get build information |
| * |
| * Response is null-terminated string. |
| */ |
| #define EC_CMD_GET_BUILD_INFO 0x0004 |
| |
| /* Get chip info */ |
| #define EC_CMD_GET_CHIP_INFO 0x0005 |
| |
| struct __ec_align4 ec_response_get_chip_info { |
| /* Null-terminated strings */ |
| char vendor[32]; |
| char name[32]; |
| char revision[32]; /* Mask version */ |
| }; |
| |
| /* Get board HW version */ |
| #define EC_CMD_GET_BOARD_VERSION 0x0006 |
| |
| struct __ec_align2 ec_response_board_version { |
| uint16_t board_version; /* A monotonously incrementing number. */ |
| }; |
| |
| /* |
| * Read memory-mapped data. |
| * |
| * This is an alternate interface to memory-mapped data for bus protocols |
| * which don't support direct-mapped memory - I2C, SPI, etc. |
| * |
| * Response is params.size bytes of data. |
| */ |
| #define EC_CMD_READ_MEMMAP 0x0007 |
| |
| struct __ec_align1 ec_params_read_memmap { |
| uint8_t offset; /* Offset in memmap (EC_MEMMAP_*) */ |
| uint8_t size; /* Size to read in bytes */ |
| }; |
| |
| /* Read versions supported for a command */ |
| #define EC_CMD_GET_CMD_VERSIONS 0x0008 |
| |
| struct __ec_align1 ec_params_get_cmd_versions { |
| uint8_t cmd; /* Command to check */ |
| }; |
| |
| struct __ec_align2 ec_params_get_cmd_versions_v1 { |
| uint16_t cmd; /* Command to check */ |
| }; |
| |
| struct __ec_align4 ec_response_get_cmd_versions { |
| /* |
| * Mask of supported versions; use EC_VER_MASK() to compare with a |
| * desired version. |
| */ |
| uint32_t version_mask; |
| }; |
| |
| /* |
| * Check EC communications status (busy). This is needed on i2c/spi but not |
| * on lpc since it has its own out-of-band busy indicator. |
| * |
| * lpc must read the status from the command register. Attempting this on |
| * lpc will overwrite the args/parameter space and corrupt its data. |
| */ |
| #define EC_CMD_GET_COMMS_STATUS 0x0009 |
| |
| /* Avoid using ec_status which is for return values */ |
| enum ec_comms_status { |
| EC_COMMS_STATUS_PROCESSING = 1 << 0, /* Processing cmd */ |
| }; |
| |
| struct __ec_align4 ec_response_get_comms_status { |
| uint32_t flags; /* Mask of enum ec_comms_status */ |
| }; |
| |
| /* Fake a variety of responses, purely for testing purposes. */ |
| #define EC_CMD_TEST_PROTOCOL 0x000A |
| |
| /* Tell the EC what to send back to us. */ |
| struct __ec_align4 ec_params_test_protocol { |
| uint32_t ec_result; |
| uint32_t ret_len; |
| uint8_t buf[32]; |
| }; |
| |
| /* Here it comes... */ |
| struct __ec_align4 ec_response_test_protocol { |
| uint8_t buf[32]; |
| }; |
| |
| /* Get protocol information */ |
| #define EC_CMD_GET_PROTOCOL_INFO 0x000B |
| |
| /* Flags for ec_response_get_protocol_info.flags */ |
| /* EC_RES_IN_PROGRESS may be returned if a command is slow */ |
| #define EC_PROTOCOL_INFO_IN_PROGRESS_SUPPORTED (1 << 0) |
| |
| struct __ec_align4 ec_response_get_protocol_info { |
| /* Fields which exist if at least protocol version 3 supported */ |
| |
| /* Bitmask of protocol versions supported (1 << n means version n)*/ |
| uint32_t protocol_versions; |
| |
| /* Maximum request packet size, in bytes */ |
| uint16_t max_request_packet_size; |
| |
| /* Maximum response packet size, in bytes */ |
| uint16_t max_response_packet_size; |
| |
| /* Flags; see EC_PROTOCOL_INFO_* */ |
| uint32_t flags; |
| }; |
| |
| |
| /*****************************************************************************/ |
| /* Get/Set miscellaneous values */ |
| |
| /* The upper byte of .flags tells what to do (nothing means "get") */ |
| #define EC_GSV_SET 0x80000000 |
| |
| /* The lower three bytes of .flags identifies the parameter, if that has |
| meaning for an individual command. */ |
| #define EC_GSV_PARAM_MASK 0x00ffffff |
| |
| struct __ec_align4 ec_params_get_set_value { |
| uint32_t flags; |
| uint32_t value; |
| }; |
| |
| struct __ec_align4 ec_response_get_set_value { |
| uint32_t flags; |
| uint32_t value; |
| }; |
| |
| /* More than one command can use these structs to get/set parameters. */ |
| #define EC_CMD_GSV_PAUSE_IN_S5 0x000C |
| |
| /*****************************************************************************/ |
| /* List the features supported by the firmware */ |
| #define EC_CMD_GET_FEATURES 0x000D |
| |
| /* Supported features */ |
| enum ec_feature_code { |
| /* |
| * This image contains a limited set of features. Another image |
| * in RW partition may support more features. |
| */ |
| EC_FEATURE_LIMITED = 0, |
| /* |
| * Commands for probing/reading/writing/erasing the flash in the |
| * EC are present. |
| */ |
| EC_FEATURE_FLASH = 1, |
| /* |
| * Can control the fan speed directly. |
| */ |
| EC_FEATURE_PWM_FAN = 2, |
| /* |
| * Can control the intensity of the keyboard backlight. |
| */ |
| EC_FEATURE_PWM_KEYB = 3, |
| /* |
| * Support Google lightbar, introduced on Pixel. |
| */ |
| EC_FEATURE_LIGHTBAR = 4, |
| /* Control of LEDs */ |
| EC_FEATURE_LED = 5, |
| /* Exposes an interface to control gyro and sensors. |
| * The host goes through the EC to access these sensors. |
| * In addition, the EC may provide composite sensors, like lid angle. |
| */ |
| EC_FEATURE_MOTION_SENSE = 6, |
| /* The keyboard is controlled by the EC */ |
| EC_FEATURE_KEYB = 7, |
| /* The AP can use part of the EC flash as persistent storage. */ |
| EC_FEATURE_PSTORE = 8, |
| /* The EC monitors BIOS port 80h, and can return POST codes. */ |
| EC_FEATURE_PORT80 = 9, |
| /* |
| * Thermal management: include TMP specific commands. |
| * Higher level than direct fan control. |
| */ |
| EC_FEATURE_THERMAL = 10, |
| /* Can switch the screen backlight on/off */ |
| EC_FEATURE_BKLIGHT_SWITCH = 11, |
| /* Can switch the wifi module on/off */ |
| EC_FEATURE_WIFI_SWITCH = 12, |
| /* Monitor host events, through for example SMI or SCI */ |
| EC_FEATURE_HOST_EVENTS = 13, |
| /* The EC exposes GPIO commands to control/monitor connected devices. */ |
| EC_FEATURE_GPIO = 14, |
| /* The EC can send i2c messages to downstream devices. */ |
| EC_FEATURE_I2C = 15, |
| /* Command to control charger are included */ |
| EC_FEATURE_CHARGER = 16, |
| /* Simple battery support. */ |
| EC_FEATURE_BATTERY = 17, |
| /* |
| * Support Smart battery protocol |
| * (Common Smart Battery System Interface Specification) |
| */ |
| EC_FEATURE_SMART_BATTERY = 18, |
| /* EC can detect when the host hangs. */ |
| EC_FEATURE_HANG_DETECT = 19, |
| /* Report power information, for pit only */ |
| EC_FEATURE_PMU = 20, |
| /* Another Cros EC device is present downstream of this one */ |
| EC_FEATURE_SUB_MCU = 21, |
| /* Support USB Power delivery (PD) commands */ |
| EC_FEATURE_USB_PD = 22, |
| /* Control USB multiplexer, for audio through USB port for instance. */ |
| EC_FEATURE_USB_MUX = 23, |
| /* Motion Sensor code has an internal software FIFO */ |
| EC_FEATURE_MOTION_SENSE_FIFO = 24, |
| /* Support temporary secure vstore */ |
| EC_FEATURE_VSTORE = 25, |
| /* EC decides on USB-C SS mux state, muxes configured by host */ |
| EC_FEATURE_USBC_SS_MUX_VIRTUAL = 26, |
| /* EC has RTC feature that can be controlled by host commands */ |
| EC_FEATURE_RTC = 27, |
| /* The MCU exposes a Fingerprint sensor */ |
| EC_FEATURE_FINGERPRINT = 28, |
| /* The MCU exposes a Touchpad */ |
| EC_FEATURE_TOUCHPAD = 29, |
| /* The MCU has RWSIG task enabled */ |
| EC_FEATURE_RWSIG = 30, |
| /* EC has device events support */ |
| EC_FEATURE_DEVICE_EVENT = 31, |
| /* EC supports the unified wake masks for LPC/eSPI systems */ |
| EC_FEATURE_UNIFIED_WAKE_MASKS = 32, |
| /* EC supports 64-bit host events */ |
| EC_FEATURE_HOST_EVENT64 = 33, |
| /* EC runs code in RAM (not in place, a.k.a. XIP) */ |
| EC_FEATURE_EXEC_IN_RAM = 34, |
| /* EC supports CEC commands */ |
| EC_FEATURE_CEC = 35, |
| /* EC supports tight sensor timestamping. */ |
| EC_FEATURE_MOTION_SENSE_TIGHT_TIMESTAMPS = 36, |
| /* |
| * EC supports tablet mode detection aligned to Chrome and allows |
| * setting of threshold by host command using |
| * MOTIONSENSE_CMD_TABLET_MODE_LID_ANGLE. |
| */ |
| EC_FEATURE_REFINED_TABLET_MODE_HYSTERESIS = 37, |
| /* |
| * Early Firmware Selection ver.2. Enabled by CONFIG_VBOOT_EFS2. |
| * Note this is a RO feature. So, a query (EC_CMD_GET_FEATURES) should |
| * be sent to RO to be precise. |
| */ |
| EC_FEATURE_EFS2 = 38, |
| /* The MCU is a System Companion Processor (SCP). */ |
| EC_FEATURE_SCP = 39, |
| /* The MCU is an Integrated Sensor Hub */ |
| EC_FEATURE_ISH = 40, |
| /* New TCPMv2 TYPEC_ prefaced commands supported */ |
| EC_FEATURE_TYPEC_CMD = 41, |
| /* |
| * The EC will wait for direction from the AP to enter Type-C alternate |
| * modes or USB4. |
| */ |
| EC_FEATURE_TYPEC_REQUIRE_AP_MODE_ENTRY = 42, |
| /* |
| * The EC will wait for an acknowledge from the AP after setting the |
| * mux. |
| */ |
| EC_FEATURE_TYPEC_MUX_REQUIRE_AP_ACK = 43, |
| }; |
| |
| #define EC_FEATURE_MASK_0(event_code) BIT(event_code % 32) |
| #define EC_FEATURE_MASK_1(event_code) BIT(event_code - 32) |
| |
| struct ec_response_get_features { |
| uint32_t flags[2]; |
| } __ec_align4; |
| |
| /*****************************************************************************/ |
| /* Get the board's SKU ID from EC */ |
| #define EC_CMD_GET_SKU_ID 0x000E |
| |
| /* Set SKU ID from AP */ |
| #define EC_CMD_SET_SKU_ID 0x000F |
| |
| struct __ec_align4 ec_sku_id_info { |
| uint32_t sku_id; |
| }; |
| |
| /*****************************************************************************/ |
| /* Flash commands */ |
| |
| /* Get flash info */ |
| #define EC_CMD_FLASH_INFO 0x0010 |
| #define EC_VER_FLASH_INFO 2 |
| |
| /* Version 0 returns these fields */ |
| struct __ec_align4 ec_response_flash_info { |
| /* Usable flash size, in bytes */ |
| uint32_t flash_size; |
| /* |
| * Write block size. Write offset and size must be a multiple |
| * of this. |
| */ |
| uint32_t write_block_size; |
| /* |
| * Erase block size. Erase offset and size must be a multiple |
| * of this. |
| */ |
| uint32_t erase_block_size; |
| /* |
| * Protection block size. Protection offset and size must be a |
| * multiple of this. |
| */ |
| uint32_t protect_block_size; |
| }; |
| |
| /* Flags for version 1+ flash info command */ |
| /* EC flash erases bits to 0 instead of 1 */ |
| #define EC_FLASH_INFO_ERASE_TO_0 (1 << 0) |
| |
| /* Flash must be selected for read/write/erase operations to succeed. This may |
| * be necessary on a chip where write/erase can be corrupted by other board |
| * activity, or where the chip needs to enable some sort of programming voltage, |
| * or where the read/write/erase operations require cleanly suspending other |
| * chip functionality. */ |
| #define EC_FLASH_INFO_SELECT_REQUIRED (1 << 1) |
| |
| /* |
| * Version 1 returns the same initial fields as version 0, with additional |
| * fields following. |
| * |
| * gcc anonymous structs don't seem to get along with the __packed directive; |
| * if they did we'd define the version 0 structure as a sub-structure of this |
| * one. |
| * |
| * Version 2 supports flash banks of different sizes: |
| * The caller specified the number of banks it has preallocated |
| * (num_banks_desc) |
| * The EC returns the number of banks describing the flash memory. |
| * It adds banks descriptions up to num_banks_desc. |
| */ |
| struct __ec_align4 ec_response_flash_info_1 { |
| /* Version 0 fields; see above for description */ |
| uint32_t flash_size; |
| uint32_t write_block_size; |
| uint32_t erase_block_size; |
| uint32_t protect_block_size; |
| |
| /* Version 1 adds these fields: */ |
| /* |
| * Ideal write size in bytes. Writes will be fastest if size is |
| * exactly this and offset is a multiple of this. For example, an EC |
| * may have a write buffer which can do half-page operations if data is |
| * aligned, and a slower word-at-a-time write mode. |
| */ |
| uint32_t write_ideal_size; |
| |
| /* Flags; see EC_FLASH_INFO_* */ |
| uint32_t flags; |
| }; |
| |
| struct __ec_align4 ec_params_flash_info_2 { |
| /* Number of banks to describe */ |
| uint16_t num_banks_desc; |
| /* Reserved; set 0; ignore on read */ |
| uint8_t reserved[2]; |
| }; |
| |
| struct ec_flash_bank { |
| /* Number of sector is in this bank. */ |
| uint16_t count; |
| /* Size in power of 2 of each sector (8 --> 256 bytes) */ |
| uint8_t size_exp; |
| /* Minimal write size for the sectors in this bank */ |
| uint8_t write_size_exp; |
| /* Erase size for the sectors in this bank */ |
| uint8_t erase_size_exp; |
| /* Size for write protection, usually identical to erase size. */ |
| uint8_t protect_size_exp; |
| /* Reserved; set 0; ignore on read */ |
| uint8_t reserved[2]; |
| }; |
| |
| struct __ec_align4 ec_response_flash_info_2 { |
| /* Total flash in the EC. */ |
| uint32_t flash_size; |
| /* Flags; see EC_FLASH_INFO_* */ |
| uint32_t flags; |
| /* Maximum size to use to send data to write to the EC. */ |
| uint32_t write_ideal_size; |
| /* Number of banks present in the EC. */ |
| uint16_t num_banks_total; |
| /* Number of banks described in banks array. */ |
| uint16_t num_banks_desc; |
| struct ec_flash_bank banks[0]; |
| }; |
| |
| /* |
| * Read flash |
| * |
| * Response is params.size bytes of data. |
| */ |
| #define EC_CMD_FLASH_READ 0x0011 |
| |
| struct __ec_align4 ec_params_flash_read { |
| uint32_t offset; /* Byte offset to read */ |
| uint32_t size; /* Size to read in bytes */ |
| }; |
| |
| /* Write flash */ |
| #define EC_CMD_FLASH_WRITE 0x0012 |
| #define EC_VER_FLASH_WRITE 1 |
| |
| /* Version 0 of the flash command supported only 64 bytes of data */ |
| #define EC_FLASH_WRITE_VER0_SIZE 64 |
| |
| struct __ec_align4 ec_params_flash_write { |
| uint32_t offset; /* Byte offset to write */ |
| uint32_t size; /* Size to write in bytes */ |
| /* Followed by data to write */ |
| }; |
| |
| /* Erase flash */ |
| #define EC_CMD_FLASH_ERASE 0x0013 |
| |
| /* v0 */ |
| struct __ec_align4 ec_params_flash_erase { |
| uint32_t offset; /* Byte offset to erase */ |
| uint32_t size; /* Size to erase in bytes */ |
| }; |
| |
| |
| #define EC_VER_FLASH_WRITE 1 |
| /* v1 add async erase: |
| * subcommands can returns: |
| * EC_RES_SUCCESS : erased (see ERASE_SECTOR_ASYNC case below). |
| * EC_RES_INVALID_PARAM : offset/size are not aligned on a erase boundary. |
| * EC_RES_ERROR : other errors. |
| * EC_RES_BUSY : an existing erase operation is in progress. |
| * EC_RES_ACCESS_DENIED: Trying to erase running image. |
| * |
| * When ERASE_SECTOR_ASYNC returns EC_RES_SUCCESS, the operation is just |
| * properly queued. The user must call ERASE_GET_RESULT subcommand to get |
| * the proper result. |
| * When ERASE_GET_RESULT returns EC_RES_BUSY, the caller must wait and send |
| * ERASE_GET_RESULT again to get the result of ERASE_SECTOR_ASYNC. |
| * ERASE_GET_RESULT command may timeout on EC where flash access is not |
| * permitted while erasing. (For instance, STM32F4). |
| */ |
| enum ec_flash_erase_cmd { |
| FLASH_ERASE_SECTOR, /* Erase and wait for result */ |
| FLASH_ERASE_SECTOR_ASYNC, /* Erase and return immediately. */ |
| FLASH_ERASE_GET_RESULT, /* Ask for last erase result */ |
| }; |
| |
| struct __ec_align4 ec_params_flash_erase_v1 { |
| /* One of ec_flash_erase_cmd. */ |
| uint8_t cmd; |
| /* Pad byte; currently always contains 0 */ |
| uint8_t reserved; |
| /* No flags defined yet; set to 0 */ |
| uint16_t flag; |
| /* Same as v0 parameters. */ |
| struct ec_params_flash_erase params; |
| }; |
| |
| /* |
| * Get/set flash protection. |
| * |
| * If mask!=0, sets/clear the requested bits of flags. Depending on the |
| * firmware write protect GPIO, not all flags will take effect immediately; |
| * some flags require a subsequent hard reset to take effect. Check the |
| * returned flags bits to see what actually happened. |
| * |
| * If mask=0, simply returns the current flags state. |
| */ |
| #define EC_CMD_FLASH_PROTECT 0x0015 |
| #define EC_VER_FLASH_PROTECT 1 /* Command version 1 */ |
| |
| /* Flags for flash protection */ |
| /* RO flash code protected when the EC boots */ |
| #define EC_FLASH_PROTECT_RO_AT_BOOT (1 << 0) |
| /* |
| * RO flash code protected now. If this bit is set, at-boot status cannot |
| * be changed. |
| */ |
| #define EC_FLASH_PROTECT_RO_NOW (1 << 1) |
| /* Entire flash code protected now, until reboot. */ |
| #define EC_FLASH_PROTECT_ALL_NOW (1 << 2) |
| /* Flash write protect GPIO is asserted now */ |
| #define EC_FLASH_PROTECT_GPIO_ASSERTED (1 << 3) |
| /* Error - at least one bank of flash is stuck locked, and cannot be unlocked */ |
| #define EC_FLASH_PROTECT_ERROR_STUCK (1 << 4) |
| /* |
| * Error - flash protection is in inconsistent state. At least one bank of |
| * flash which should be protected is not protected. Usually fixed by |
| * re-requesting the desired flags, or by a hard reset if that fails. |
| */ |
| #define EC_FLASH_PROTECT_ERROR_INCONSISTENT (1 << 5) |
| /* Entire flash code protected when the EC boots */ |
| #define EC_FLASH_PROTECT_ALL_AT_BOOT (1 << 6) |
| /* RW flash code protected when the EC boots */ |
| #define EC_FLASH_PROTECT_RW_AT_BOOT (1 << 7) |
| /* RW flash code protected now. */ |
| #define EC_FLASH_PROTECT_RW_NOW (1 << 8) |
| /* Rollback information flash region protected when the EC boots */ |
| #define EC_FLASH_PROTECT_ROLLBACK_AT_BOOT (1 << 9) |
| /* Rollback information flash region protected now */ |
| #define EC_FLASH_PROTECT_ROLLBACK_NOW (1 << 10) |
| |
| struct __ec_align4 ec_params_flash_protect { |
| uint32_t mask; /* Bits in flags to apply */ |
| uint32_t flags; /* New flags to apply */ |
| }; |
| |
| struct __ec_align4 ec_response_flash_protect { |
| /* Current value of flash protect flags */ |
| uint32_t flags; |
| /* |
| * Flags which are valid on this platform. This allows the caller |
| * to distinguish between flags which aren't set vs. flags which can't |
| * be set on this platform. |
| */ |
| uint32_t valid_flags; |
| /* Flags which can be changed given the current protection state */ |
| uint32_t writable_flags; |
| }; |
| |
| /* |
| * Note: commands 0x14 - 0x19 version 0 were old commands to get/set flash |
| * write protect. These commands may be reused with version > 0. |
| */ |
| |
| /* Get the region offset/size */ |
| #define EC_CMD_FLASH_REGION_INFO 0x0016 |
| #define EC_VER_FLASH_REGION_INFO 1 |
| |
| enum ec_flash_region { |
| /* Region which holds read-only EC image */ |
| EC_FLASH_REGION_RO = 0, |
| /* Region which holds active rewritable EC image */ |
| EC_FLASH_REGION_ACTIVE, |
| /* |
| * Region which should be write-protected in the factory (a superset of |
| * EC_FLASH_REGION_RO) |
| */ |
| EC_FLASH_REGION_WP_RO, |
| /* Region which holds updatable image */ |
| EC_FLASH_REGION_UPDATE, |
| /* Number of regions */ |
| EC_FLASH_REGION_COUNT, |
| }; |
| |
| struct __ec_align4 ec_params_flash_region_info { |
| uint32_t region; /* enum ec_flash_region */ |
| }; |
| |
| struct __ec_align4 ec_response_flash_region_info { |
| uint32_t offset; |
| uint32_t size; |
| }; |
| |
| /* Read/write VbNvContext */ |
| #define EC_CMD_VBNV_CONTEXT 0x0017 |
| #define EC_VER_VBNV_CONTEXT 1 |
| #define EC_VBNV_BLOCK_SIZE 16 |
| #define EC_VBNV_BLOCK_SIZE_V2 64 |
| |
| enum ec_vbnvcontext_op { |
| EC_VBNV_CONTEXT_OP_READ, |
| EC_VBNV_CONTEXT_OP_WRITE, |
| }; |
| |
| struct __ec_align4 ec_params_vbnvcontext { |
| uint32_t op; |
| uint8_t block[EC_VBNV_BLOCK_SIZE_V2]; |
| }; |
| |
| struct __ec_align4 ec_response_vbnvcontext { |
| uint8_t block[EC_VBNV_BLOCK_SIZE_V2]; |
| }; |
| |
| |
| /* Get SPI flash information */ |
| #define EC_CMD_FLASH_SPI_INFO 0x0018 |
| |
| struct __ec_align1 ec_response_flash_spi_info { |
| /* JEDEC info from command 0x9F (manufacturer, memory type, size) */ |
| uint8_t jedec[3]; |
| |
| /* Pad byte; currently always contains 0 */ |
| uint8_t reserved0; |
| |
| /* Manufacturer / device ID from command 0x90 */ |
| uint8_t mfr_dev_id[2]; |
| |
| /* Status registers from command 0x05 and 0x35 */ |
| uint8_t sr1, sr2; |
| }; |
| |
| |
| /* Select flash during flash operations */ |
| #define EC_CMD_FLASH_SELECT 0x0019 |
| |
| struct __ec_align4 ec_params_flash_select { |
| /* 1 to select flash, 0 to deselect flash */ |
| uint8_t select; |
| }; |
| |
| /*****************************************************************************/ |
| /* PWM commands */ |
| |
| /* Get fan target RPM */ |
| #define EC_CMD_PWM_GET_FAN_TARGET_RPM 0x0020 |
| |
| struct __ec_align4 ec_response_pwm_get_fan_rpm { |
| uint32_t rpm; |
| }; |
| |
| /* Set target fan RPM */ |
| #define EC_CMD_PWM_SET_FAN_TARGET_RPM 0x0021 |
| |
| /* Version 0 of input params */ |
| struct __ec_align4 ec_params_pwm_set_fan_target_rpm_v0 { |
| uint32_t rpm; |
| }; |
| |
| /* Version 1 of input params */ |
| struct __ec_align_size1 ec_params_pwm_set_fan_target_rpm_v1 { |
| uint32_t rpm; |
| uint8_t fan_idx; |
| }; |
| |
| /* Get keyboard backlight */ |
| /* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */ |
| #define EC_CMD_PWM_GET_KEYBOARD_BACKLIGHT 0x0022 |
| |
| struct __ec_align1 ec_response_pwm_get_keyboard_backlight { |
| uint8_t percent; |
| uint8_t enabled; |
| }; |
| |
| /* Set keyboard backlight */ |
| /* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */ |
| #define EC_CMD_PWM_SET_KEYBOARD_BACKLIGHT 0x0023 |
| |
| struct __ec_align1 ec_params_pwm_set_keyboard_backlight { |
| uint8_t percent; |
| }; |
| |
| /* Set target fan PWM duty cycle */ |
| #define EC_CMD_PWM_SET_FAN_DUTY 0x0024 |
| |
| /* Version 0 of input params */ |
| struct __ec_align4 ec_params_pwm_set_fan_duty_v0 { |
| uint32_t percent; |
| }; |
| |
| /* Version 1 of input params */ |
| struct __ec_align_size1 ec_params_pwm_set_fan_duty_v1 { |
| uint32_t percent; |
| uint8_t fan_idx; |
| }; |
| |
| #define EC_CMD_PWM_SET_DUTY 0x0025 |
| /* 16 bit duty cycle, 0xffff = 100% */ |
| #define EC_PWM_MAX_DUTY 0xffff |
| |
| enum ec_pwm_type { |
| /* All types, indexed by board-specific enum pwm_channel */ |
| EC_PWM_TYPE_GENERIC = 0, |
| /* Keyboard backlight */ |
| EC_PWM_TYPE_KB_LIGHT, |
| /* Display backlight */ |
| EC_PWM_TYPE_DISPLAY_LIGHT, |
| EC_PWM_TYPE_COUNT, |
| }; |
| |
| struct __ec_align4 ec_params_pwm_set_duty { |
| uint16_t duty; /* Duty cycle, EC_PWM_MAX_DUTY = 100% */ |
| uint8_t pwm_type; /* ec_pwm_type */ |
| uint8_t index; /* Type-specific index, or 0 if unique */ |
| }; |
| |
| #define EC_CMD_PWM_GET_DUTY 0x0026 |
| |
| struct __ec_align1 ec_params_pwm_get_duty { |
| uint8_t pwm_type; /* ec_pwm_type */ |
| uint8_t index; /* Type-specific index, or 0 if unique */ |
| }; |
| |
| struct __ec_align2 ec_response_pwm_get_duty { |
| uint16_t duty; /* Duty cycle, EC_PWM_MAX_DUTY = 100% */ |
| }; |
| |
| /*****************************************************************************/ |
| /* |
| * Lightbar commands. This looks worse than it is. Since we only use one HOST |
| * command to say "talk to the lightbar", we put the "and tell it to do X" part |
| * into a subcommand. We'll make separate structs for subcommands with |
| * different input args, so that we know how much to expect. |
| */ |
| #define EC_CMD_LIGHTBAR_CMD 0x0028 |
| |
| struct __ec_todo_unpacked rgb_s { |
| uint8_t r, g, b; |
| }; |
| |
| #define LB_BATTERY_LEVELS 4 |
| /* List of tweakable parameters. NOTE: It's __packed so it can be sent in a |
| * host command, but the alignment is the same regardless. Keep it that way. |
| */ |
| struct __ec_todo_packed lightbar_params_v0 { |
| /* Timing */ |
| int32_t google_ramp_up; |
| int32_t google_ramp_down; |
| int32_t s3s0_ramp_up; |
| int32_t s0_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0a_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0s3_ramp_down; |
| int32_t s3_sleep_for; |
| int32_t s3_ramp_up; |
| int32_t s3_ramp_down; |
| |
| /* Oscillation */ |
| uint8_t new_s0; |
| uint8_t osc_min[2]; /* AC=0/1 */ |
| uint8_t osc_max[2]; /* AC=0/1 */ |
| uint8_t w_ofs[2]; /* AC=0/1 */ |
| |
| /* Brightness limits based on the backlight and AC. */ |
| uint8_t bright_bl_off_fixed[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_min[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_max[2]; /* AC=0/1 */ |
| |
| /* Battery level thresholds */ |
| uint8_t battery_threshold[LB_BATTERY_LEVELS - 1]; |
| |
| /* Map [AC][battery_level] to color index */ |
| uint8_t s0_idx[2][LB_BATTERY_LEVELS]; /* AP is running */ |
| uint8_t s3_idx[2][LB_BATTERY_LEVELS]; /* AP is sleeping */ |
| |
| /* Color palette */ |
| struct rgb_s color[8]; /* 0-3 are Google colors */ |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v1 { |
| /* Timing */ |
| int32_t google_ramp_up; |
| int32_t google_ramp_down; |
| int32_t s3s0_ramp_up; |
| int32_t s0_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0a_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0s3_ramp_down; |
| int32_t s3_sleep_for; |
| int32_t s3_ramp_up; |
| int32_t s3_ramp_down; |
| int32_t s5_ramp_up; |
| int32_t s5_ramp_down; |
| int32_t tap_tick_delay; |
| int32_t tap_gate_delay; |
| int32_t tap_display_time; |
| |
| /* Tap-for-battery params */ |
| uint8_t tap_pct_red; |
| uint8_t tap_pct_green; |
| uint8_t tap_seg_min_on; |
| uint8_t tap_seg_max_on; |
| uint8_t tap_seg_osc; |
| uint8_t tap_idx[3]; |
| |
| /* Oscillation */ |
| uint8_t osc_min[2]; /* AC=0/1 */ |
| uint8_t osc_max[2]; /* AC=0/1 */ |
| uint8_t w_ofs[2]; /* AC=0/1 */ |
| |
| /* Brightness limits based on the backlight and AC. */ |
| uint8_t bright_bl_off_fixed[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_min[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_max[2]; /* AC=0/1 */ |
| |
| /* Battery level thresholds */ |
| uint8_t battery_threshold[LB_BATTERY_LEVELS - 1]; |
| |
| /* Map [AC][battery_level] to color index */ |
| uint8_t s0_idx[2][LB_BATTERY_LEVELS]; /* AP is running */ |
| uint8_t s3_idx[2][LB_BATTERY_LEVELS]; /* AP is sleeping */ |
| |
| /* s5: single color pulse on inhibited power-up */ |
| uint8_t s5_idx; |
| |
| /* Color palette */ |
| struct rgb_s color[8]; /* 0-3 are Google colors */ |
| }; |
| |
| /* Lightbar command params v2 |
| * crbug.com/467716 |
| * |
| * lightbar_parms_v1 was too big for i2c, therefore in v2, we split them up by |
| * logical groups to make it more manageable ( < 120 bytes). |
| * |
| * NOTE: Each of these groups must be less than 120 bytes. |
| */ |
| |
| struct __ec_todo_packed lightbar_params_v2_timing { |
| /* Timing */ |
| int32_t google_ramp_up; |
| int32_t google_ramp_down; |
| int32_t s3s0_ramp_up; |
| int32_t s0_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0a_tick_delay[2]; /* AC=0/1 */ |
| int32_t s0s3_ramp_down; |
| int32_t s3_sleep_for; |
| int32_t s3_ramp_up; |
| int32_t s3_ramp_down; |
| int32_t s5_ramp_up; |
| int32_t s5_ramp_down; |
| int32_t tap_tick_delay; |
| int32_t tap_gate_delay; |
| int32_t tap_display_time; |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v2_tap { |
| /* Tap-for-battery params */ |
| uint8_t tap_pct_red; |
| uint8_t tap_pct_green; |
| uint8_t tap_seg_min_on; |
| uint8_t tap_seg_max_on; |
| uint8_t tap_seg_osc; |
| uint8_t tap_idx[3]; |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v2_oscillation { |
| /* Oscillation */ |
| uint8_t osc_min[2]; /* AC=0/1 */ |
| uint8_t osc_max[2]; /* AC=0/1 */ |
| uint8_t w_ofs[2]; /* AC=0/1 */ |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v2_brightness { |
| /* Brightness limits based on the backlight and AC. */ |
| uint8_t bright_bl_off_fixed[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_min[2]; /* AC=0/1 */ |
| uint8_t bright_bl_on_max[2]; /* AC=0/1 */ |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v2_thresholds { |
| /* Battery level thresholds */ |
| uint8_t battery_threshold[LB_BATTERY_LEVELS - 1]; |
| }; |
| |
| struct __ec_todo_packed lightbar_params_v2_colors { |
| /* Map [AC][battery_level] to color index */ |
| uint8_t s0_idx[2][LB_BATTERY_LEVELS]; /* AP is running */ |
| uint8_t s3_idx[2][LB_BATTERY_LEVELS]; /* AP is sleeping */ |
| |
| /* s5: single color pulse on inhibited power-up */ |
| uint8_t s5_idx; |
| |
| /* Color palette */ |
| struct rgb_s color[8]; /* 0-3 are Google colors */ |
| }; |
| |
| /* Lightbyte program. */ |
| #define EC_LB_PROG_LEN 192 |
| struct __ec_todo_unpacked lightbar_program { |
| uint8_t size; |
| uint8_t data[EC_LB_PROG_LEN]; |
| }; |
| |
| struct __ec_todo_packed ec_params_lightbar { |
| uint8_t cmd; /* Command (see enum lightbar_command) */ |
| union { |
| struct __ec_todo_unpacked { |
| /* no args */ |
| } dump, off, on, init, get_seq, get_params_v0, get_params_v1, |
| version, get_brightness, get_demo, suspend, resume, |
| get_params_v2_timing, get_params_v2_tap, |
| get_params_v2_osc, get_params_v2_bright, |
| get_params_v2_thlds, get_params_v2_colors; |
| |
| struct __ec_todo_unpacked { |
| uint8_t num; |
| } set_brightness, seq, demo; |
| |
| struct __ec_todo_unpacked { |
| uint8_t ctrl, reg, value; |
| } reg; |
| |
| struct __ec_todo_unpacked { |
| uint8_t led, red, green, blue; |
| } set_rgb; |
| |
| struct __ec_todo_unpacked { |
| uint8_t led; |
| } get_rgb; |
| |
| struct __ec_todo_unpacked { |
| uint8_t enable; |
| } manual_suspend_ctrl; |
| |
| struct lightbar_params_v0 set_params_v0; |
| struct lightbar_params_v1 set_params_v1; |
| |
| struct lightbar_params_v2_timing set_v2par_timing; |
| struct lightbar_params_v2_tap set_v2par_tap; |
| struct lightbar_params_v2_oscillation set_v2par_osc; |
| struct lightbar_params_v2_brightness set_v2par_bright; |
| struct lightbar_params_v2_thresholds set_v2par_thlds; |
| struct lightbar_params_v2_colors set_v2par_colors; |
| |
| struct lightbar_program set_program; |
| }; |
| }; |
| |
| struct __ec_todo_packed ec_response_lightbar { |
| union { |
| struct __ec_todo_unpacked { |
| struct __ec_todo_unpacked { |
| uint8_t reg; |
| uint8_t ic0; |
| uint8_t ic1; |
| } vals[23]; |
| } dump; |
| |
| struct __ec_todo_unpacked { |
| uint8_t num; |
| } get_seq, get_brightness, get_demo; |
| |
| struct lightbar_params_v0 get_params_v0; |
| struct lightbar_params_v1 get_params_v1; |
| |
| |
| struct lightbar_params_v2_timing get_params_v2_timing; |
| struct lightbar_params_v2_tap get_params_v2_tap; |
| struct lightbar_params_v2_oscillation get_params_v2_osc; |
| struct lightbar_params_v2_brightness get_params_v2_bright; |
| struct lightbar_params_v2_thresholds get_params_v2_thlds; |
| struct lightbar_params_v2_colors get_params_v2_colors; |
| |
| struct __ec_todo_unpacked { |
| uint32_t num; |
| uint32_t flags; |
| } version; |
| |
| struct __ec_todo_unpacked { |
| uint8_t red, green, blue; |
| } get_rgb; |
| |
| struct __ec_todo_unpacked { |
| /* no return params */ |
| } off, on, init, set_brightness, seq, reg, set_rgb, |
| demo, set_params_v0, set_params_v1, |
| set_program, manual_suspend_ctrl, suspend, resume, |
| set_v2par_timing, set_v2par_tap, |
| set_v2par_osc, set_v2par_bright, set_v2par_thlds, |
| set_v2par_colors; |
| }; |
| }; |
| |
| /* Lightbar commands */ |
| enum lightbar_command { |
| LIGHTBAR_CMD_DUMP = 0, |
| LIGHTBAR_CMD_OFF = 1, |
| LIGHTBAR_CMD_ON = 2, |
| LIGHTBAR_CMD_INIT = 3, |
| LIGHTBAR_CMD_SET_BRIGHTNESS = 4, |
| LIGHTBAR_CMD_SEQ = 5, |
| LIGHTBAR_CMD_REG = 6, |
| LIGHTBAR_CMD_SET_RGB = 7, |
| LIGHTBAR_CMD_GET_SEQ = 8, |
| LIGHTBAR_CMD_DEMO = 9, |
| LIGHTBAR_CMD_GET_PARAMS_V0 = 10, |
| LIGHTBAR_CMD_SET_PARAMS_V0 = 11, |
| LIGHTBAR_CMD_VERSION = 12, |
| LIGHTBAR_CMD_GET_BRIGHTNESS = 13, |
| LIGHTBAR_CMD_GET_RGB = 14, |
| LIGHTBAR_CMD_GET_DEMO = 15, |
| LIGHTBAR_CMD_GET_PARAMS_V1 = 16, |
| LIGHTBAR_CMD_SET_PARAMS_V1 = 17, |
| LIGHTBAR_CMD_SET_PROGRAM = 18, |
| LIGHTBAR_CMD_MANUAL_SUSPEND_CTRL = 19, |
| LIGHTBAR_CMD_SUSPEND = 20, |
| LIGHTBAR_CMD_RESUME = 21, |
| LIGHTBAR_CMD_GET_PARAMS_V2_TIMING = 22, |
| LIGHTBAR_CMD_SET_PARAMS_V2_TIMING = 23, |
| LIGHTBAR_CMD_GET_PARAMS_V2_TAP = 24, |
| LIGHTBAR_CMD_SET_PARAMS_V2_TAP = 25, |
| LIGHTBAR_CMD_GET_PARAMS_V2_OSCILLATION = 26, |
| LIGHTBAR_CMD_SET_PARAMS_V2_OSCILLATION = 27, |
| LIGHTBAR_CMD_GET_PARAMS_V2_BRIGHTNESS = 28, |
| LIGHTBAR_CMD_SET_PARAMS_V2_BRIGHTNESS = 29, |
| LIGHTBAR_CMD_GET_PARAMS_V2_THRESHOLDS = 30, |
| LIGHTBAR_CMD_SET_PARAMS_V2_THRESHOLDS = 31, |
| LIGHTBAR_CMD_GET_PARAMS_V2_COLORS = 32, |
| LIGHTBAR_CMD_SET_PARAMS_V2_COLORS = 33, |
| LIGHTBAR_NUM_CMDS |
| }; |
| |
| /*****************************************************************************/ |
| /* LED control commands */ |
| |
| #define EC_CMD_LED_CONTROL 0x0029 |
| |
| enum ec_led_id { |
| /* LED to indicate battery state of charge */ |
| EC_LED_ID_BATTERY_LED = 0, |
| /* |
| * LED to indicate system power state (on or in suspend). |
| * May be on power button or on C-panel. |
| */ |
| EC_LED_ID_POWER_LED, |
| /* LED on power adapter or its plug */ |
| EC_LED_ID_ADAPTER_LED, |
| /* LED to indicate left side */ |
| EC_LED_ID_LEFT_LED, |
| /* LED to indicate right side */ |
| EC_LED_ID_RIGHT_LED, |
| /* LED to indicate recovery mode with HW_REINIT */ |
| EC_LED_ID_RECOVERY_HW_REINIT_LED, |
| /* LED to indicate sysrq debug mode. */ |
| EC_LED_ID_SYSRQ_DEBUG_LED, |
| |
| EC_LED_ID_COUNT |
| }; |
| |
| /* LED control flags */ |
| #define EC_LED_FLAGS_QUERY (1 << 0) /* Query LED capability only */ |
| #define EC_LED_FLAGS_AUTO (1 << 1) /* Switch LED back to automatic control */ |
| |
| enum ec_led_colors { |
| EC_LED_COLOR_RED = 0, |
| EC_LED_COLOR_GREEN, |
| EC_LED_COLOR_BLUE, |
| EC_LED_COLOR_YELLOW, |
| EC_LED_COLOR_WHITE, |
| EC_LED_COLOR_AMBER, |
| |
| EC_LED_COLOR_COUNT |
| }; |
| |
| struct __ec_align1 ec_params_led_control { |
| uint8_t led_id; /* Which LED to control */ |
| uint8_t flags; /* Control flags */ |
| |
| uint8_t brightness[EC_LED_COLOR_COUNT]; |
| }; |
| |
| struct __ec_align1 ec_response_led_control { |
| /* |
| * Available brightness value range. |
| * |
| * Range 0 means color channel not present. |
| * Range 1 means on/off control. |
| * Other values means the LED is control by PWM. |
| */ |
| uint8_t brightness_range[EC_LED_COLOR_COUNT]; |
| }; |
| |
| /*****************************************************************************/ |
| /* Verified boot commands */ |
| |
| /* |
| * Note: command code 0x29 version 0 was VBOOT_CMD in Link EVT; it may be |
| * reused for other purposes with version > 0. |
| */ |
| |
| /* Verified boot hash command */ |
| #define EC_CMD_VBOOT_HASH 0x002A |
| |
| struct __ec_align4 ec_params_vboot_hash { |
| uint8_t cmd; /* enum ec_vboot_hash_cmd */ |
| uint8_t hash_type; /* enum ec_vboot_hash_type */ |
| uint8_t nonce_size; /* Nonce size; may be 0 */ |
| uint8_t reserved0; /* Reserved; set 0 */ |
| uint32_t offset; /* Offset in flash to hash */ |
| uint32_t size; /* Number of bytes to hash */ |
| uint8_t nonce_data[64]; /* Nonce data; ignored if nonce_size=0 */ |
| }; |
| |
| struct __ec_align4 ec_response_vboot_hash { |
| uint8_t status; /* enum ec_vboot_hash_status */ |
| uint8_t hash_type; /* enum ec_vboot_hash_type */ |
| uint8_t digest_size; /* Size of hash digest in bytes */ |
| uint8_t reserved0; /* Ignore; will be 0 */ |
| uint32_t offset; /* Offset in flash which was hashed */ |
| uint32_t size; /* Number of bytes hashed */ |
| uint8_t hash_digest[64]; /* Hash digest data */ |
| }; |
| |
| enum ec_vboot_hash_cmd { |
| EC_VBOOT_HASH_GET = 0, /* Get current hash status */ |
| EC_VBOOT_HASH_ABORT = 1, /* Abort calculating current hash */ |
| EC_VBOOT_HASH_START = 2, /* Start computing a new hash */ |
| EC_VBOOT_HASH_RECALC = 3, /* Synchronously compute a new hash */ |
| }; |
| |
| enum ec_vboot_hash_type { |
| EC_VBOOT_HASH_TYPE_SHA256 = 0, /* SHA-256 */ |
| }; |
| |
| enum ec_vboot_hash_status { |
| EC_VBOOT_HASH_STATUS_NONE = 0, /* No hash (not started, or aborted) */ |
| EC_VBOOT_HASH_STATUS_DONE = 1, /* Finished computing a hash */ |
| EC_VBOOT_HASH_STATUS_BUSY = 2, /* Busy computing a hash */ |
| }; |
| |
| /* |
| * Special values for offset for EC_VBOOT_HASH_START and EC_VBOOT_HASH_RECALC. |
| * If one of these is specified, the EC will automatically update offset and |
| * size to the correct values for the specified image (RO or RW). |
| */ |
| #define EC_VBOOT_HASH_OFFSET_RO 0xfffffffe |
| #define EC_VBOOT_HASH_OFFSET_ACTIVE 0xfffffffd |
| #define EC_VBOOT_HASH_OFFSET_UPDATE 0xfffffffc |
| |
| /*****************************************************************************/ |
| /* |
| * Motion sense commands. We'll make separate structs for sub-commands with |
| * different input args, so that we know how much to expect. |
| */ |
| #define EC_CMD_MOTION_SENSE_CMD 0x002B |
| |
| /* Motion sense commands */ |
| enum motionsense_command { |
| /* |
| * Dump command returns all motion sensor data including motion sense |
| * module flags and individual sensor flags. |
| */ |
| MOTIONSENSE_CMD_DUMP = 0, |
| |
| /* |
| * Info command returns data describing the details of a given sensor, |
| * including enum motionsensor_type, enum motionsensor_location, and |
| * enum motionsensor_chip. |
| */ |
| MOTIONSENSE_CMD_INFO = 1, |
| |
| /* |
| * EC Rate command is a setter/getter command for the EC sampling rate |
| * in milliseconds. |
| * It is per sensor, the EC run sample task at the minimum of all |
| * sensors EC_RATE. |
| * For sensors without hardware FIFO, EC_RATE should be equals to 1/ODR |
| * to collect all the sensor samples. |
| * For sensor with hardware FIFO, EC_RATE is used as the maximal delay |
| * to process of all motion sensors in milliseconds. |
| */ |
| MOTIONSENSE_CMD_EC_RATE = 2, |
| |
| /* |
| * Sensor ODR command is a setter/getter command for the output data |
| * rate of a specific motion sensor in millihertz. |
| */ |
| MOTIONSENSE_CMD_SENSOR_ODR = 3, |
| |
| /* |
| * Sensor range command is a setter/getter command for the range of |
| * a specified motion sensor in +/-G's or +/- deg/s. |
| */ |
| MOTIONSENSE_CMD_SENSOR_RANGE = 4, |
| |
| /* |
| * Setter/getter command for the keyboard wake angle. When the lid |
| * angle is greater than this value, keyboard wake is disabled in S3, |
| * and when the lid angle goes less than this value, keyboard wake is |
| * enabled. Note, the lid angle measurement is an approximate, |
| * un-calibrated value, hence the wake angle isn't exact. |
| */ |
| MOTIONSENSE_CMD_KB_WAKE_ANGLE = 5, |
| |
| /* |
| * Returns a single sensor data. |
| */ |
| MOTIONSENSE_CMD_DATA = 6, |
| |
| /* |
| * Return sensor fifo info. |
| */ |
| MOTIONSENSE_CMD_FIFO_INFO = 7, |
| |
| /* |
| * Insert a flush element in the fifo and return sensor fifo info. |
| * The host can use that element to synchronize its operation. |
| */ |
| MOTIONSENSE_CMD_FIFO_FLUSH = 8, |
| |
| /* |
| * Return a portion of the fifo. |
| */ |
| MOTIONSENSE_CMD_FIFO_READ = 9, |
| |
| /* |
| * Perform low level calibration. |
| * On sensors that support it, ask to do offset calibration. |
| */ |
| MOTIONSENSE_CMD_PERFORM_CALIB = 10, |
| |
| /* |
| * Sensor Offset command is a setter/getter command for the offset |
| * used for calibration. |
| * The offsets can be calculated by the host, or via |
| * PERFORM_CALIB command. |
| */ |
| MOTIONSENSE_CMD_SENSOR_OFFSET = 11, |
| |
| /* |
| * List available activities for a MOTION sensor. |
| * Indicates if they are enabled or disabled. |
| */ |
| MOTIONSENSE_CMD_LIST_ACTIVITIES = 12, |
| |
| /* |
| * Activity management |
| * Enable/Disable activity recognition. |
| */ |
| MOTIONSENSE_CMD_SET_ACTIVITY = 13, |
| |
| /* |
| * Lid Angle |
| */ |
| MOTIONSENSE_CMD_LID_ANGLE = 14, |
| |
| /* |
| * Allow the FIFO to trigger interrupt via MKBP events. |
| * By default the FIFO does not send interrupt to process the FIFO |
| * until the AP is ready or it is coming from a wakeup sensor. |
| */ |
| MOTIONSENSE_CMD_FIFO_INT_ENABLE = 15, |
| |
| /* |
| * Spoof the readings of the sensors. The spoofed readings can be set |
| * to arbitrary values, or will lock to the last read actual values. |
| */ |
| MOTIONSENSE_CMD_SPOOF = 16, |
| |
| /* Number of motionsense sub-commands. */ |
| MOTIONSENSE_NUM_CMDS |
| }; |
| |
| /* List of motion sensor types. */ |
| enum motionsensor_type { |
| MOTIONSENSE_TYPE_ACCEL = 0, |
| MOTIONSENSE_TYPE_GYRO = 1, |
| MOTIONSENSE_TYPE_MAG = 2, |
| MOTIONSENSE_TYPE_PROX = 3, |
| MOTIONSENSE_TYPE_LIGHT = 4, |
| MOTIONSENSE_TYPE_ACTIVITY = 5, |
| MOTIONSENSE_TYPE_BARO = 6, |
| MOTIONSENSE_TYPE_MAX, |
| }; |
| |
| /* List of motion sensor locations. */ |
| enum motionsensor_location { |
| MOTIONSENSE_LOC_BASE = 0, |
| MOTIONSENSE_LOC_LID = 1, |
| MOTIONSENSE_LOC_MAX, |
| }; |
| |
| /* List of motion sensor chips. */ |
| enum motionsensor_chip { |
| MOTIONSENSE_CHIP_KXCJ9 = 0, |
| MOTIONSENSE_CHIP_LSM6DS0 = 1, |
| MOTIONSENSE_CHIP_BMI160 = 2, |
| MOTIONSENSE_CHIP_SI1141 = 3, |
| MOTIONSENSE_CHIP_SI1142 = 4, |
| MOTIONSENSE_CHIP_SI1143 = 5, |
| MOTIONSENSE_CHIP_KX022 = 6, |
| MOTIONSENSE_CHIP_L3GD20H = 7, |
| MOTIONSENSE_CHIP_BMA255 = 8, |
| MOTIONSENSE_CHIP_BMP280 = 9, |
| MOTIONSENSE_CHIP_OPT3001 = 10, |
| }; |
| |
| struct __ec_todo_packed ec_response_motion_sensor_data { |
| /* Flags for each sensor. */ |
| uint8_t flags; |
| /* sensor number the data comes from */ |
| uint8_t sensor_num; |
| /* Each sensor is up to 3-axis. */ |
| union { |
| int16_t data[3]; |
| struct __ec_todo_packed { |
| uint16_t reserved; |
| uint32_t timestamp; |
| }; |
| struct __ec_todo_unpacked { |
| uint8_t activity; /* motionsensor_activity */ |
| uint8_t state; |
| int16_t add_info[2]; |
| }; |
| }; |
| }; |
| |
| /* Note: used in ec_response_get_next_data */ |
| struct __ec_todo_packed ec_response_motion_sense_fifo_info { |
| /* Size of the fifo */ |
| uint16_t size; |
| /* Amount of space used in the fifo */ |
| uint16_t count; |
| /* Timestamp recorded in us */ |
| uint32_t timestamp; |
| /* Total amount of vector lost */ |
| uint16_t total_lost; |
| /* Lost events since the last fifo_info, per sensors */ |
| uint16_t lost[0]; |
| }; |
| |
| struct __ec_todo_packed ec_response_motion_sense_fifo_data { |
| uint32_t number_data; |
| struct ec_response_motion_sensor_data data[0]; |
| }; |
| |
| /* List supported activity recognition */ |
| enum motionsensor_activity { |
| MOTIONSENSE_ACTIVITY_RESERVED = 0, |
| MOTIONSENSE_ACTIVITY_SIG_MOTION = 1, |
| MOTIONSENSE_ACTIVITY_DOUBLE_TAP = 2, |
| }; |
| |
| struct __ec_todo_unpacked ec_motion_sense_activity { |
| uint8_t sensor_num; |
| uint8_t activity; /* one of enum motionsensor_activity */ |
| uint8_t enable; /* 1: enable, 0: disable */ |
| uint8_t reserved; |
| uint16_t parameters[3]; /* activity dependent parameters */ |
| }; |
| |
| /* Module flag masks used for the dump sub-command. */ |
| #define MOTIONSENSE_MODULE_FLAG_ACTIVE (1<<0) |
| |
| /* Sensor flag masks used for the dump sub-command. */ |
| #define MOTIONSENSE_SENSOR_FLAG_PRESENT (1<<0) |
| |
| /* |
| * Flush entry for synchronization. |
| * data contains time stamp |
| */ |
| #define MOTIONSENSE_SENSOR_FLAG_FLUSH (1<<0) |
| #define MOTIONSENSE_SENSOR_FLAG_TIMESTAMP (1<<1) |
| #define MOTIONSENSE_SENSOR_FLAG_WAKEUP (1<<2) |
| #define MOTIONSENSE_SENSOR_FLAG_TABLET_MODE (1<<3) |
| |
| /* |
| * Send this value for the data element to only perform a read. If you |
| * send any other value, the EC will interpret it as data to set and will |
| * return the actual value set. |
| */ |
| #define EC_MOTION_SENSE_NO_VALUE -1 |
| |
| #define EC_MOTION_SENSE_INVALID_CALIB_TEMP 0x8000 |
| |
| /* MOTIONSENSE_CMD_SENSOR_OFFSET subcommand flag */ |
| /* Set Calibration information */ |
| #define MOTION_SENSE_SET_OFFSET 1 |
| |
| #define LID_ANGLE_UNRELIABLE 500 |
| |
| enum motionsense_spoof_mode { |
| /* Disable spoof mode. */ |
| MOTIONSENSE_SPOOF_MODE_DISABLE = 0, |
| |
| /* Enable spoof mode, but use provided component values. */ |
| MOTIONSENSE_SPOOF_MODE_CUSTOM, |
| |
| /* Enable spoof mode, but use the current sensor values. */ |
| MOTIONSENSE_SPOOF_MODE_LOCK_CURRENT, |
| |
| /* Query the current spoof mode status for the sensor. */ |
| MOTIONSENSE_SPOOF_MODE_QUERY, |
| }; |
| |
| struct __ec_todo_packed ec_params_motion_sense { |
| uint8_t cmd; |
| union { |
| /* Used for MOTIONSENSE_CMD_DUMP */ |
| struct __ec_todo_unpacked { |
| /* |
| * Maximal number of sensor the host is expecting. |
| * 0 means the host is only interested in the number |
| * of sensors controlled by the EC. |
| */ |
| uint8_t max_sensor_count; |
| } dump; |
| |
| /* |
| * Used for MOTIONSENSE_CMD_KB_WAKE_ANGLE. |
| */ |
| struct __ec_todo_unpacked { |
| /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. |
| * kb_wake_angle: angle to wakup AP. |
| */ |
| int16_t data; |
| } kb_wake_angle; |
| |
| /* Used for MOTIONSENSE_CMD_INFO, MOTIONSENSE_CMD_DATA |
| * and MOTIONSENSE_CMD_PERFORM_CALIB. */ |
| struct __ec_todo_unpacked { |
| uint8_t sensor_num; |
| } info, info_3, data, fifo_flush, perform_calib, |
| list_activities; |
| |
| /* |
| * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR |
| * and MOTIONSENSE_CMD_SENSOR_RANGE. |
| */ |
| struct __ec_todo_unpacked { |
| uint8_t sensor_num; |
| |
| /* Rounding flag, true for round-up, false for down. */ |
| uint8_t roundup; |
| |
| uint16_t reserved; |
| |
| /* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */ |
| int32_t data; |
| } ec_rate, sensor_odr, sensor_range; |
| |
| /* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */ |
| struct __ec_todo_packed { |
| uint8_t sensor_num; |
| |
| /* |
| * bit 0: If set (MOTION_SENSE_SET_OFFSET), set |
| * the calibration information in the EC. |
| * If unset, just retrieve calibration information. |
| */ |
| uint16_t flags; |
| |
| /* |
| * Temperature at calibration, in units of 0.01 C |
| * 0x8000: invalid / unknown. |
| * 0x0: 0C |
| * 0x7fff: +327.67C |
| */ |
| int16_t temp; |
| |
| /* |
| * Offset for calibration. |
| * Unit: |
| * Accelerometer: 1/1024 g |
| * Gyro: 1/1024 deg/s |
| * Compass: 1/16 uT |
| */ |
| int16_t offset[3]; |
| } sensor_offset; |
| |
| /* Used for MOTIONSENSE_CMD_FIFO_INFO */ |
| struct __ec_todo_unpacked { |
| } fifo_info; |
| |
| /* Used for MOTIONSENSE_CMD_FIFO_READ */ |
| struct __ec_todo_unpacked { |
| /* |
| * Number of expected vector to return. |
| * EC may return less or 0 if none available. |
| */ |
| uint32_t max_data_vector; |
| } fifo_read; |
| |
| struct ec_motion_sense_activity set_activity; |
| |
| /* Used for MOTIONSENSE_CMD_LID_ANGLE */ |
| struct __ec_todo_unpacked { |
| } lid_angle; |
| |
| /* Used for MOTIONSENSE_CMD_FIFO_INT_ENABLE */ |
| struct __ec_todo_unpacked { |
| /* |
| * 1: enable, 0 disable fifo, |
| * EC_MOTION_SENSE_NO_VALUE return value. |
| */ |
| int8_t enable; |
| } fifo_int_enable; |
| |
| /* Used for MOTIONSENSE_CMD_SPOOF */ |
| struct __ec_todo_packed { |
| uint8_t sensor_id; |
| |
| /* See enum motionsense_spoof_mode. */ |
| uint8_t spoof_enable; |
| |
| /* Ignored, used for alignment. */ |
| uint8_t reserved; |
| |
| /* Individual component values to spoof. */ |
| int16_t components[3]; |
| } spoof; |
| }; |
| }; |
| |
| struct __ec_todo_packed ec_response_motion_sense { |
| union { |
| /* Used for MOTIONSENSE_CMD_DUMP */ |
| struct __ec_todo_unpacked { |
| /* Flags representing the motion sensor module. */ |
| uint8_t module_flags; |
| |
| /* Number of sensors managed directly by the EC */ |
| uint8_t sensor_count; |
| |
| /* |
| * sensor data is truncated if response_max is too small |
| * for holding all the data. |
| */ |
| struct ec_response_motion_sensor_data sensor[0]; |
| } dump; |
| |
| /* Used for MOTIONSENSE_CMD_INFO. */ |
| struct __ec_todo_unpacked { |
| /* Should be element of enum motionsensor_type. */ |
| uint8_t type; |
| |
| /* Should be element of enum motionsensor_location. */ |
| uint8_t location; |
| |
| /* Should be element of enum motionsensor_chip. */ |
| uint8_t chip; |
| } info; |
| |
| /* Used for MOTIONSENSE_CMD_INFO version 3 */ |
| struct __ec_todo_unpacked { |
| /* Should be element of enum motionsensor_type. */ |
| uint8_t type; |
| |
| /* Should be element of enum motionsensor_location. */ |
| uint8_t location; |
| |
| /* Should be element of enum motionsensor_chip. */ |
| uint8_t chip; |
| |
| /* Minimum sensor sampling frequency */ |
| uint32_t min_frequency; |
| |
| /* Maximum sensor sampling frequency */ |
| uint32_t max_frequency; |
| |
| /* Max number of sensor events that could be in fifo */ |
| uint32_t fifo_max_event_count; |
| } info_3; |
| |
| /* Used for MOTIONSENSE_CMD_DATA */ |
| struct ec_response_motion_sensor_data data; |
| |
| /* |
| * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR, |
| * MOTIONSENSE_CMD_SENSOR_RANGE, |
| * MOTIONSENSE_CMD_KB_WAKE_ANGLE, |
| * MOTIONSENSE_CMD_FIFO_INT_ENABLE and |
| * MOTIONSENSE_CMD_SPOOF. |
| */ |
| struct __ec_todo_unpacked { |
| /* Current value of the parameter queried. */ |
| int32_t ret; |
| } ec_rate, sensor_odr, sensor_range, kb_wake_angle, |
| fifo_int_enable, spoof; |
| |
| /* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */ |
| struct __ec_todo_unpacked { |
| int16_t temp; |
| int16_t offset[3]; |
| } sensor_offset, perform_calib; |
| |
| struct ec_response_motion_sense_fifo_info fifo_info, fifo_flush; |
| |
| struct ec_response_motion_sense_fifo_data fifo_read; |
| |
| struct __ec_todo_packed { |
| uint16_t reserved; |
| uint32_t enabled; |
| uint32_t disabled; |
| } list_activities; |
| |
| struct __ec_todo_unpacked { |
| } set_activity; |
| |
| /* Used for MOTIONSENSE_CMD_LID_ANGLE */ |
| struct __ec_todo_unpacked { |
| /* |
| * Angle between 0 and 360 degree if available, |
| * LID_ANGLE_UNRELIABLE otherwise. |
| */ |
| uint16_t value; |
| } lid_angle; |
| }; |
| }; |
| |
| /*****************************************************************************/ |
| /* Force lid open command */ |
| |
| /* Make lid event always open */ |
| #define EC_CMD_FORCE_LID_OPEN 0x002C |
| |
| struct __ec_align1 ec_params_force_lid_open { |
| uint8_t enabled; |
| }; |
| |
| /*****************************************************************************/ |
| /* Configure the behavior of the power button */ |
| #define EC_CMD_CONFIG_POWER_BUTTON 0x002D |
| |
| enum ec_config_power_button_flags { |
| /* Enable/Disable power button pulses for x86 devices */ |
| EC_POWER_BUTTON_ENABLE_PULSE = (1 << 0), |
| }; |
| |
| struct __ec_align1 ec_params_config_power_button { |
| /* See enum ec_config_power_button_flags */ |
| uint8_t flags; |
| }; |
| |
| /*****************************************************************************/ |
| /* USB charging control commands */ |
| |
| /* Set USB port charging mode */ |
| #define EC_CMD_USB_CHARGE_SET_MODE 0x0030 |
| |
| struct __ec_align1 ec_params_usb_charge_set_mode { |
| uint8_t usb_port_id; |
| uint8_t mode; |
| }; |
| |
| /*****************************************************************************/ |
| /* Persistent storage for host */ |
| |
| /* Maximum bytes that can be read/written in a single command */ |
| #define EC_PSTORE_SIZE_MAX 64 |
| |
| /* Get persistent storage info */ |
| #define EC_CMD_PSTORE_INFO 0x0040 |
| |
| struct __ec_align4 ec_response_pstore_info { |
| /* Persistent storage size, in bytes */ |
| uint32_t pstore_size; |
| /* Access size; read/write offset and size must be a multiple of this */ |
| uint32_t access_size; |
| }; |
| |
| /* |
| * Read persistent storage |
| * |
| * Response is params.size bytes of data. |
| */ |
| #define EC_CMD_PSTORE_READ 0x0041 |
| |
| struct __ec_align4 ec_params_pstore_read { |
| uint32_t offset; /* Byte offset to read */ |
| uint32_t size; /* Size to read in bytes */ |
| }; |
| |
| /* Write persistent storage */ |
| #define EC_CMD_PSTORE_WRITE 0x0042 |
| |
| struct __ec_align4 ec_params_pstore_write { |
| uint32_t offset; /* Byte offset to write */ |
| uint32_t size; /* Size to write in bytes */ |
| uint8_t data[EC_PSTORE_SIZE_MAX]; |
| }; |
| |
| /*****************************************************************************/ |
| /* Real-time clock */ |
| |
| /* RTC params and response structures */ |
| struct __ec_align4 ec_params_rtc { |
| uint32_t time; |
| }; |
| |
| struct __ec_align4 ec_response_rtc { |
| uint32_t time; |
| }; |
| |
| /* These use ec_response_rtc */ |
| #define EC_CMD_RTC_GET_VALUE 0x0044 |
| #define EC_CMD_RTC_GET_ALARM 0x0045 |
| |
| /* These all use ec_params_rtc */ |
| #define EC_CMD_RTC_SET_VALUE 0x0046 |
| #define EC_CMD_RTC_SET_ALARM 0x0047 |
| |
| /* Pass as time param to SET_ALARM to clear the current alarm */ |
| #define EC_RTC_ALARM_CLEAR 0 |
| |
| /*****************************************************************************/ |
| /* Port80 log access */ |
| |
| /* Maximum entries that can be read/written in a single command */ |
| #define EC_PORT80_SIZE_MAX 32 |
| |
| /* Get last port80 code from previous boot */ |
| #define EC_CMD_PORT80_LAST_BOOT 0x0048 |
| #define EC_CMD_PORT80_READ 0x0048 |
| |
| enum ec_port80_subcmd { |
| EC_PORT80_GET_INFO = 0, |
| EC_PORT80_READ_BUFFER, |
| }; |
| |
| struct __ec_todo_packed ec_params_port80_read { |
| uint16_t subcmd; |
| union { |
| struct __ec_todo_unpacked { |
| uint32_t offset; |
| uint32_t num_entries; |
| } read_buffer; |
| }; |
| }; |
| |
| struct __ec_todo_packed ec_response_port80_read { |
| union { |
| struct __ec_todo_unpacked { |
| uint32_t writes; |
| uint32_t history_size; |
| uint32_t last_boot; |
| } get_info; |
| struct __ec_todo_unpacked { |
| uint16_t codes[EC_PORT80_SIZE_MAX]; |
| } data; |
| }; |
| }; |
| |
| struct __ec_align2 ec_response_port80_last_boot { |
| uint16_t code; |
| }; |
| |
| /*****************************************************************************/ |
| /* Temporary secure storage for host verified boot use */ |
| |
| /* Number of bytes in a vstore slot */ |
| #define EC_VSTORE_SLOT_SIZE 64 |
| |
| /* Maximum number of vstore slots */ |
| #define EC_VSTORE_SLOT_MAX 32 |
| |
| /* Get persistent storage info */ |
| #define EC_CMD_VSTORE_INFO 0x0049 |
| struct __ec_align_size1 ec_response_vstore_info { |
| /* Indicates which slots are locked */ |
| uint32_t slot_locked; |
| /* Total number of slots available */ |
| uint8_t slot_count; |
| }; |
| |
| /* |
| * Read temporary secure storage |
| * |
| * Response is EC_VSTORE_SLOT_SIZE bytes of data. |
| */ |
| #define EC_CMD_VSTORE_READ 0x004A |
| |
| struct __ec_align1 ec_params_vstore_read { |
| uint8_t slot; /* Slot to read from */ |
| }; |
| |
| struct __ec_align1 ec_response_vstore_read { |
| uint8_t data[EC_VSTORE_SLOT_SIZE]; |
| }; |
| |
| /* |
| * Write temporary secure storage and lock it. |
| */ |
| #define EC_CMD_VSTORE_WRITE 0x004B |
| |
| struct __ec_align1 ec_params_vstore_write { |
| uint8_t slot; /* Slot to write to */ |
| uint8_t data[EC_VSTORE_SLOT_SIZE]; |
| }; |
| |
| /*****************************************************************************/ |
| /* Thermal engine commands. Note that there are two implementations. We'll |
| * reuse the command number, but the data and behavior is incompatible. |
| * Version 0 is what originally shipped on Link. |
| * Version 1 separates the CPU thermal limits from the fan control. |
| */ |
| |
| #define EC_CMD_THERMAL_SET_THRESHOLD 0x0050 |
| #define EC_CMD_THERMAL_GET_THRESHOLD 0x0051 |
| |
| /* The version 0 structs are opaque. You have to know what they are for |
| * the get/set commands to make any sense. |
| */ |
| |
| /* Version 0 - set */ |
| struct __ec_align2 ec_params_thermal_set_threshold { |
| uint8_t sensor_type; |
| uint8_t threshold_id; |
| uint16_t value; |
| }; |
| |
| /* Version 0 - get */ |
| struct __ec_align1 ec_params_thermal_get_threshold { |
| uint8_t sensor_type; |
| uint8_t threshold_id; |
| }; |
| |
| struct __ec_align2 ec_response_thermal_get_threshold { |
| uint16_t value; |
| }; |
| |
| |
| /* The version 1 structs are visible. */ |
| enum ec_temp_thresholds { |
| EC_TEMP_THRESH_WARN = 0, |
| EC_TEMP_THRESH_HIGH, |
| EC_TEMP_THRESH_HALT, |
| |
| EC_TEMP_THRESH_COUNT |
| }; |
| |
| /* |
| * Thermal configuration for one temperature sensor. Temps are in degrees K. |
| * Zero values will be silently ignored by the thermal task. |
| * |
| * Note that this structure is a sub-structure of |
| * ec_params_thermal_set_threshold_v1, but maintains its alignment there. |
| */ |
| struct __ec_align4 ec_thermal_config { |
| uint32_t temp_host[EC_TEMP_THRESH_COUNT]; /* levels of hotness */ |
| uint32_t temp_fan_off; /* no active cooling needed */ |
| uint32_t temp_fan_max; /* max active cooling needed */ |
| }; |
| |
| /* Version 1 - get config for one sensor. */ |
| struct __ec_align4 ec_params_thermal_get_threshold_v1 { |
| uint32_t sensor_num; |
| }; |
| /* This returns a struct ec_thermal_config */ |
| |
| /* Version 1 - set config for one sensor. |
| * Use read-modify-write for best results! */ |
| struct __ec_align4 ec_params_thermal_set_threshold_v1 { |
| uint32_t sensor_num; |
| struct ec_thermal_config cfg; |
| }; |
| /* This returns no data */ |
| |
| /****************************************************************************/ |
| |
| /* Toggle automatic fan control */ |
| #define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x0052 |
| |
| /* Version 1 of input params */ |
| struct __ec_align1 ec_params_auto_fan_ctrl_v1 { |
| uint8_t fan_idx; |
| }; |
| |
| /* Get/Set TMP006 calibration data */ |
| #define EC_CMD_TMP006_GET_CALIBRATION 0x0053 |
| #define EC_CMD_TMP006_SET_CALIBRATION 0x0054 |
| |
| /* |
| * The original TMP006 calibration only needed four params, but now we need |
| * more. Since the algorithm is nothing but magic numbers anyway, we'll leave |
| * the params opaque. The v1 "get" response will include the algorithm number |
| * and how many params it requires. That way we can change the EC code without |
| * needing to update this file. We can also use a different algorithm on each |
| * sensor. |
| */ |
| |
| /* This is the same struct for both v0 and v1. */ |
| struct __ec_align1 ec_params_tmp006_get_calibration { |
| uint8_t index; |
| }; |
| |
| /* Version 0 */ |
| struct __ec_align4 ec_response_tmp006_get_calibration_v0 { |
| float s0; |
| float b0; |
| float b1; |
| float b2; |
| }; |
| |
| struct __ec_align4 ec_params_tmp006_set_calibration_v0 { |
| uint8_t index; |
| uint8_t reserved[3]; |
| float s0; |
| float b0; |
| float b1; |
| float b2; |
| }; |
| |
| /* Version 1 */ |
| struct __ec_align4 ec_response_tmp006_get_calibration_v1 { |
| uint8_t algorithm; |
| uint8_t num_params; |
| uint8_t reserved[2]; |
| float val[0]; |
| }; |
| |
| struct __ec_align4 ec_params_tmp006_set_calibration_v1 { |
| uint8_t index; |
| uint8_t algorithm; |
| uint8_t num_params; |
| uint8_t reserved; |
| float val[0]; |
| }; |
| |
| |
| /* Read raw TMP006 data */ |
| #define EC_CMD_TMP006_GET_RAW 0x0055 |
| |
| struct __ec_align1 ec_params_tmp006_get_raw { |
| uint8_t index; |
| }; |
| |
| struct __ec_align4 ec_response_tmp006_get_raw { |
| int32_t t; /* In 1/100 K */ |
| int32_t v; /* In nV */ |
| }; |
| |
| /*****************************************************************************/ |
| /* MKBP - Matrix KeyBoard Protocol */ |
| |
| /* |
| * Read key state |
| * |
| * Returns raw data for keyboard cols; see ec_response_mkbp_info.cols for |
| * expected response size. |
| * |
| * NOTE: This has been superseded by EC_CMD_MKBP_GET_NEXT_EVENT. If you wish |
| * to obtain the instantaneous state, use EC_CMD_MKBP_INFO with the type |
| * EC_MKBP_INFO_CURRENT and event EC_MKBP_EVENT_KEY_MATRIX. |
| */ |
| #define EC_CMD_MKBP_STATE 0x0060 |
| |
| /* |
| * Provide information about various MKBP things. See enum ec_mkbp_info_type. |
| */ |
| #define EC_CMD_MKBP_INFO 0x0061 |
| |
| struct __ec_align_size1 ec_response_mkbp_info { |
| uint32_t rows; |
| uint32_t cols; |
| /* Formerly "switches", which was 0. */ |
| uint8_t reserved; |
| }; |
| |
| struct __ec_align1 ec_params_mkbp_info { |
| uint8_t info_type; |
| uint8_t event_type; |
| }; |
| |
| enum ec_mkbp_info_type { |
| /* |
| * Info about the keyboard matrix: number of rows and columns. |
| * |
| * Returns struct ec_response_mkbp_info. |
| */ |
| EC_MKBP_INFO_KBD = 0, |
| |
| /* |
| * For buttons and switches, info about which specifically are |
| * supported. event_type must be set to one of the values in enum |
| * ec_mkbp_event. |
| * |
| * For EC_MKBP_EVENT_BUTTON and EC_MKBP_EVENT_SWITCH, returns a 4 byte |
| * bitmask indicating which buttons or switches are present. See the |
| * bit inidices below. |
| */ |
| EC_MKBP_INFO_SUPPORTED = 1, |
| |
| /* |
| * Instantaneous state of buttons and switches. |
| * |
| * event_type must be set to one of the values in enum ec_mkbp_event. |
| * |
| * For EC_MKBP_EVENT_KEY_MATRIX, returns uint8_t key_matrix[13] |
| * indicating the current state of the keyboard matrix. |
| * |
| * For EC_MKBP_EVENT_HOST_EVENT, return uint32_t host_event, the raw |
| * event state. |
| * |
| * For EC_MKBP_EVENT_BUTTON, returns uint32_t buttons, indicating the |
| * state of supported buttons. |
| * |
| * For EC_MKBP_EVENT_SWITCH, returns uint32_t switches, indicating the |
| * state of supported switches. |
| */ |
| EC_MKBP_INFO_CURRENT = 2, |
| }; |
| |
| /* Simulate key press */ |
| #define EC_CMD_MKBP_SIMULATE_KEY 0x0062 |
| |
| struct __ec_align1 ec_params_mkbp_simulate_key { |
| uint8_t col; |
| uint8_t row; |
| uint8_t pressed; |
| }; |
| |
| /* Configure keyboard scanning */ |
| #define EC_CMD_MKBP_SET_CONFIG 0x0064 |
| #define EC_CMD_MKBP_GET_CONFIG 0x0065 |
| |
| /* flags */ |
| enum mkbp_config_flags { |
| EC_MKBP_FLAGS_ENABLE = 1, /* Enable keyboard scanning */ |
| }; |
| |
| enum mkbp_config_valid { |
| EC_MKBP_VALID_SCAN_PERIOD = 1 << 0, |
| EC_MKBP_VALID_POLL_TIMEOUT = 1 << 1, |
| EC_MKBP_VALID_MIN_POST_SCAN_DELAY = 1 << 3, |
| EC_MKBP_VALID_OUTPUT_SETTLE = 1 << 4, |
| EC_MKBP_VALID_DEBOUNCE_DOWN = 1 << 5, |
| EC_MKBP_VALID_DEBOUNCE_UP = 1 << 6, |
| EC_MKBP_VALID_FIFO_MAX_DEPTH = 1 << 7, |
| }; |
| |
| /* |
| * Configuration for our key scanning algorithm. |
| * |
| * Note that this is used as a sub-structure of |
| * ec_{params/response}_mkbp_get_config. |
| */ |
| struct __ec_align_size1 ec_mkbp_config { |
| uint32_t valid_mask; /* valid fields */ |
| uint8_t flags; /* some flags (enum mkbp_config_flags) */ |
| uint8_t valid_flags; /* which flags are valid */ |
| uint16_t scan_period_us; /* period between start of scans */ |
| /* revert to interrupt mode after no activity for this long */ |
| uint32_t poll_timeout_us; |
| /* |
| * minimum post-scan relax time. Once we finish a scan we check |
| * the time until we are due to start the next one. If this time is |
| * shorter this field, we use this instead. |
| */ |
| uint16_t min_post_scan_delay_us; |
| /* delay between setting up output and waiting for it to settle */ |
| uint16_t output_settle_us; |
| uint16_t debounce_down_us; /* time for debounce on key down */ |
| uint16_t debounce_up_us; /* time for debounce on key up */ |
| /* maximum depth to allow for fifo (0 = no keyscan output) */ |
| uint8_t fifo_max_depth; |
| }; |
| |
| struct __ec_align_size1 ec_params_mkbp_set_config { |
| struct ec_mkbp_config config; |
| }; |
| |
| struct __ec_align_size1 ec_response_mkbp_get_config { |
| struct ec_mkbp_config config; |
| }; |
| |
| /* Run the key scan emulation */ |
| #define EC_CMD_KEYSCAN_SEQ_CTRL 0x0066 |
| |
| enum ec_keyscan_seq_cmd { |
| EC_KEYSCAN_SEQ_STATUS = 0, /* Get status information */ |
| EC_KEYSCAN_SEQ_CLEAR = 1, /* Clear sequence */ |
| EC_KEYSCAN_SEQ_ADD = 2, /* Add item to sequence */ |
| EC_KEYSCAN_SEQ_START = 3, /* Start running sequence */ |
| EC_KEYSCAN_SEQ_COLLECT = 4, /* Collect sequence summary data */ |
| }; |
| |
| enum ec_collect_flags { |
| /* |
| * Indicates this scan was processed by the EC. Due to timing, some |
| * scans may be skipped. |
| */ |
| EC_KEYSCAN_SEQ_FLAG_DONE = 1 << 0, |
| }; |
| |
| struct __ec_align1 ec_collect_item { |
| uint8_t flags; /* some flags (enum ec_collect_flags) */ |
| }; |
| |
| struct __ec_todo_packed ec_params_keyscan_seq_ctrl { |
| uint8_t cmd; /* Command to send (enum ec_keyscan_seq_cmd) */ |
| union { |
| struct __ec_align1 { |
| uint8_t active; /* still active */ |
| uint8_t num_items; /* number of items */ |
| /* Current item being presented */ |
| uint8_t cur_item; |
| } status; |
| struct __ec_todo_unpacked { |
| /* |
| * Absolute time for this scan, measured from the |
| * start of the sequence. |
| */ |
| uint32_t time_us; |
| uint8_t scan[0]; /* keyscan data */ |
| } add; |
| struct __ec_align1 { |
| uint8_t start_item; /* First item to return */ |
| uint8_t num_items; /* Number of items to return */ |
| } collect; |
| }; |
| }; |
| |
| struct __ec_todo_packed ec_result_keyscan_seq_ctrl { |
| union { |
| struct __ec_todo_unpacked { |
| uint8_t num_items; /* Number of items */ |
| /* Data for each item */ |
| struct ec_collect_item item[0]; |
| } collect; |
| }; |
| }; |
| |
| /* |
| * Get the next pending MKBP event. |
| * |
| * Returns EC_RES_UNAVAILABLE if there is no event pending. |
| */ |
| #define EC_CMD_GET_NEXT_EVENT 0x0067 |
| |
| enum ec_mkbp_event { |
| /* Keyboard matrix changed. The event data is the new matrix state. */ |
| EC_MKBP_EVENT_KEY_MATRIX = 0, |
| |
| /* New host event. The event data is 4 bytes of host event flags. */ |
| EC_MKBP_EVENT_HOST_EVENT = 1, |
| |
| /* New Sensor FIFO data. The event data is fifo_info structure. */ |
| EC_MKBP_EVENT_SENSOR_FIFO = 2, |
| |
| /* The state of the non-matrixed buttons have changed. */ |
| EC_MKBP_EVENT_BUTTON = 3, |
| |
| /* The state of the switches have changed. */ |
| EC_MKBP_EVENT_SWITCH = 4, |
| |
| /* New Fingerprint sensor event, the event data is fp_events bitmap. */ |
| EC_MKBP_EVENT_FINGERPRINT = 5, |
| |
| /* |
| * Sysrq event: send emulated sysrq. The event data is sysrq, |
| * corresponding to the key to be pressed. |
| */ |
| EC_MKBP_EVENT_SYSRQ = 6, |
| |
| /* Number of MKBP events */ |
| EC_MKBP_EVENT_COUNT, |
| }; |
| |
| union __ec_align_offset1 ec_response_get_next_data { |
| uint8_t key_matrix[13]; |
| |
| /* Unaligned */ |
| uint32_t host_event; |
| |
| struct __ec_todo_unpacked { |
| /* For aligning the fifo_info */ |
| uint8_t reserved[3]; |
| struct ec_response_motion_sense_fifo_info info; |
| } sensor_fifo; |
| |
| uint32_t buttons; |
| |
| uint32_t switches; |
| |
| uint32_t fp_events; |
| |
| uint32_t sysrq; |
| }; |
| |
| struct __ec_align1 ec_response_get_next_event { |
| uint8_t event_type; |
| /* Followed by event data if any */ |
| union ec_response_get_next_data data; |
| }; |
| |
| /* Bit indices for buttons and switches.*/ |
| /* Buttons */ |
| #define EC_MKBP_POWER_BUTTON 0 |
| #define EC_MKBP_VOL_UP 1 |
| #define EC_MKBP_VOL_DOWN 2 |
| #define EC_MKBP_RECOVERY 3 |
| |
| /* Switches */ |
| #define EC_MKBP_LID_OPEN 0 |
| #define EC_MKBP_TABLET_MODE 1 |
| |
| /* Run keyboard factory test scanning */ |
| #define EC_CMD_KEYBOARD_FACTORY_TEST 0x0068 |
| |
| struct __ec_align2 ec_response_keyboard_factory_test { |
| uint16_t shorted; /* Keyboard pins are shorted */ |
| }; |
| |
| /* Fingerprint events in 'fp_events' for EC_MKBP_EVENT_FINGERPRINT */ |
| #define EC_MKBP_FP_RAW_EVENT(fp_events) ((fp_events) & 0x00FFFFFF) |
| #define EC_MKBP_FP_FINGER_DOWN (1 << 29) |
| #define EC_MKBP_FP_FINGER_UP (1 << 30) |
| #define EC_MKBP_FP_IMAGE_READY (1 << 31) |
| |
| /*****************************************************************************/ |
| /* Temperature sensor commands */ |
| |
| /* Read temperature sensor info */ |
| #define EC_CMD_TEMP_SENSOR_GET_INFO 0x0070 |
| |
| struct __ec_align1 ec_params_temp_sensor_get_info { |
| uint8_t id; |
| }; |
| |
| struct __ec_align1 ec_response_temp_sensor_get_info { |
| char sensor_name[32]; |
| uint8_t sensor_type; |
| }; |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Note: host commands 0x80 - 0x87 are reserved to avoid conflict with ACPI |
| * commands accidentally sent to the wrong interface. See the ACPI section |
| * below. |
| */ |
| |
| /*****************************************************************************/ |
| /* Host event commands */ |
| |
| |
| /* Obsolete. New implementation should use EC_CMD_PROGRAM_HOST_EVENT instead */ |
| /* |
| * Host event mask params and response structures, shared by all of the host |
| * event commands below. |
| */ |
| struct __ec_align4 ec_params_host_event_mask { |
| uint32_t mask; |
| }; |
| |
| struct __ec_align4 ec_response_host_event_mask { |
| uint32_t mask; |
| }; |
| |
| /* These all use ec_response_host_event_mask */ |
| #define EC_CMD_HOST_EVENT_GET_B 0x0087 |
| #define EC_CMD_HOST_EVENT_GET_SMI_MASK 0x0088 |
| #define EC_CMD_HOST_EVENT_GET_SCI_MASK 0x0089 |
| #define EC_CMD_HOST_EVENT_GET_WAKE_MASK 0x008D |
| |
| /* These all use ec_params_host_event_mask */ |
| #define EC_CMD_HOST_EVENT_SET_SMI_MASK 0x008A |
| #define EC_CMD_HOST_EVENT_SET_SCI_MASK 0x008B |
| #define EC_CMD_HOST_EVENT_CLEAR 0x008C |
| #define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x008E |
| #define EC_CMD_HOST_EVENT_CLEAR_B 0x008F |
| |
| /* |
| * Unified host event programming interface - Should be used by newer versions |
| * of BIOS/OS to program host events and masks |
| */ |
| |
| struct __ec_align4 ec_params_host_event { |
| |
| /* Action requested by host - one of enum ec_host_event_action. */ |
| uint8_t action; |
| |
| /* |
| * Mask type that the host requested the action on - one of |
| * enum ec_host_event_mask_type. |
| */ |
| uint8_t mask_type; |
| |
| /* Set to 0, ignore on read */ |
| uint16_t reserved; |
| |
| /* Value to be used in case of set operations. */ |
| uint64_t value; |
| }; |
| |
| /* |
| * Response structure returned by EC_CMD_HOST_EVENT. |
| * Update the value on a GET request. Set to 0 on GET/CLEAR |
| */ |
| |
| struct __ec_align4 ec_response_host_event { |
| |
| /* Mask value in case of get operation */ |
| uint64_t value; |
| }; |
| |
| enum ec_host_event_action { |
| /* |
| * params.value is ignored. Value of mask_type populated |
| * in response.value |
| */ |
| EC_HOST_EVENT_GET, |
| |
| /* Bits in params.value are set */ |
| EC_HOST_EVENT_SET, |
| |
| /* Bits in params.value are cleared */ |
| EC_HOST_EVENT_CLEAR, |
| }; |
| |
| enum ec_host_event_mask_type { |
| |
| /* Main host event copy */ |
| EC_HOST_EVENT_MAIN, |
| |
| /* Copy B of host events */ |
| EC_HOST_EVENT_B, |
| |
| /* SCI Mask */ |
| EC_HOST_EVENT_SCI_MASK, |
| |
| /* SMI Mask */ |
| EC_HOST_EVENT_SMI_MASK, |
| |
| /* Mask of events that should be always reported in hostevents */ |
| EC_HOST_EVENT_ALWAYS_REPORT_MASK, |
| |
| /* Active wake mask */ |
| EC_HOST_EVENT_ACTIVE_WAKE_MASK, |
| |
| /* Lazy wake mask for S0ix */ |
| EC_HOST_EVENT_LAZY_WAKE_MASK_S0IX, |
| |
| /* Lazy wake mask for S3 */ |
| EC_HOST_EVENT_LAZY_WAKE_MASK_S3, |
| |
| /* Lazy wake mask for S5 */ |
| EC_HOST_EVENT_LAZY_WAKE_MASK_S5, |
| }; |
| |
| #define EC_CMD_HOST_EVENT 0x00A4 |
| |
| /*****************************************************************************/ |
| /* Switch commands */ |
| |
| /* Enable/disable LCD backlight */ |
| #define EC_CMD_SWITCH_ENABLE_BKLIGHT 0x0090 |
| |
| struct __ec_align1 ec_params_switch_enable_backlight { |
| uint8_t enabled; |
| }; |
| |
| /* Enable/disable WLAN/Bluetooth */ |
| #define EC_CMD_SWITCH_ENABLE_WIRELESS 0x0091 |
| #define EC_VER_SWITCH_ENABLE_WIRELESS 1 |
| |
| /* Version 0 params; no response */ |
| struct __ec_align1 ec_params_switch_enable_wireless_v0 { |
| uint8_t enabled; |
| }; |
| |
| /* Version 1 params */ |
| struct __ec_align1 ec_params_switch_enable_wireless_v1 { |
| /* Flags to enable now */ |
| uint8_t now_flags; |
| |
| /* Which flags to copy from now_flags */ |
| uint8_t now_mask; |
| |
| /* |
| * Flags to leave enabled in S3, if they're on at the S0->S3 |
| * transition. (Other flags will be disabled by the S0->S3 |
| * transition.) |
| */ |
| uint8_t suspend_flags; |
| |
| /* Which flags to copy from suspend_flags */ |
| uint8_t suspend_mask; |
| }; |
| |
| /* Version 1 response */ |
| struct __ec_align1 ec_response_switch_enable_wireless_v1 { |
| /* Flags to enable now */ |
| uint8_t now_flags; |
| |
| /* Flags to leave enabled in S3 */ |
| uint8_t suspend_flags; |
| }; |
| |
| /*****************************************************************************/ |
| /* GPIO commands. Only available on EC if write protect has been disabled. */ |
| |
| /* Set GPIO output value */ |
| #define EC_CMD_GPIO_SET 0x0092 |
| |
| struct __ec_align1 ec_params_gpio_set { |
| char name[32]; |
| uint8_t val; |
| }; |
| |
| /* Get GPIO value */ |
| #define EC_CMD_GPIO_GET 0x0093 |
| |
| /* Version 0 of input params and response */ |
| struct __ec_align1 ec_params_gpio_get { |
| char name[32]; |
| }; |
| |
| struct __ec_align1 ec_response_gpio_get { |
| uint8_t val; |
| }; |
| |
| /* Version 1 of input params and response */ |
| struct __ec_align1 ec_params_gpio_get_v1 { |
| uint8_t subcmd; |
| union { |
| struct __ec_align1 { |
| char name[32]; |
| } get_value_by_name; |
| struct __ec_align1 { |
| uint8_t index; |
| } get_info; |
| }; |
| }; |
| |
| struct __ec_todo_packed ec_response_gpio_get_v1 { |
| union { |
| struct __ec_align1 { |
| uint8_t val; |
| } get_value_by_name, get_count; |
| struct __ec_todo_unpacked { |
| uint8_t val; |
| char name[32]; |
| uint32_t flags; |
| } get_info; |
| }; |
| }; |
| |
| enum gpio_get_subcmd { |
| EC_GPIO_GET_BY_NAME = 0, |
| EC_GPIO_GET_COUNT = 1, |
| EC_GPIO_GET_INFO = 2, |
| }; |
| |
| /*****************************************************************************/ |
| /* I2C commands. Only available when flash write protect is unlocked. */ |
| |
| /* |
| * CAUTION: These commands are deprecated, and are not supported anymore in EC |
| * builds >= 8398.0.0 (see crosbug.com/p/23570). |
| * |
| * Use EC_CMD_I2C_PASSTHRU instead. |
| */ |
| |
| /* Read I2C bus */ |
| #define EC_CMD_I2C_READ 0x0094 |
| |
| struct __ec_align_size1 ec_params_i2c_read { |
| uint16_t addr; /* 8-bit address (7-bit shifted << 1) */ |
| uint8_t read_size; /* Either 8 or 16. */ |
| uint8_t port; |
| uint8_t offset; |
| }; |
| |
| struct __ec_align2 ec_response_i2c_read { |
| uint16_t data; |
| }; |
| |
| /* Write I2C bus */ |
| #define EC_CMD_I2C_WRITE 0x0095 |
| |
| struct __ec_align_size1 ec_params_i2c_write { |
| uint16_t data; |
| uint16_t addr; /* 8-bit address (7-bit shifted << 1) */ |
| uint8_t write_size; /* Either 8 or 16. */ |
| uint8_t port; |
| uint8_t offset; |
| }; |
| |
| /*****************************************************************************/ |
| /* Charge state commands. Only available when flash write protect unlocked. */ |
| |
| /* Force charge state machine to stop charging the battery or force it to |
| * discharge the battery. |
| */ |
| #define EC_CMD_CHARGE_CONTROL 0x0096 |
| #define EC_VER_CHARGE_CONTROL 1 |
| |
| enum ec_charge_control_mode { |
| CHARGE_CONTROL_NORMAL = 0, |
| CHARGE_CONTROL_IDLE, |
| CHARGE_CONTROL_DISCHARGE, |
| }; |
| |
| struct __ec_align4 ec_params_charge_control { |
| uint32_t mode; /* enum charge_control_mode */ |
| }; |
| |
| /*****************************************************************************/ |
| /* Console commands. Only available when flash write protect is unlocked. */ |
| |
| /* Snapshot console output buffer for use by EC_CMD_CONSOLE_READ. */ |
| #define EC_CMD_CONSOLE_SNAPSHOT 0x0097 |
| |
| /* |
| * Read data from the saved snapshot. If the subcmd parameter is |
| * CONSOLE_READ_NEXT, this will return data starting from the beginning of |
| * the latest snapshot. If it is CONSOLE_READ_RECENT, it will start from the |
| * end of the previous snapshot. |
| * |
| * The params are only looked at in version >= 1 of this command. Prior |
| * versions will just default to CONSOLE_READ_NEXT behavior. |
| * |
| * Response is null-terminated string. Empty string, if there is no more |
| * remaining output. |
| */ |
| #define EC_CMD_CONSOLE_READ 0x0098 |
| |
| enum ec_console_read_subcmd { |
| CONSOLE_READ_NEXT = 0, |
| CONSOLE_READ_RECENT |
| }; |
| |
| struct __ec_align1 ec_params_console_read_v1 { |
| uint8_t subcmd; /* enum ec_console_read_subcmd */ |
| }; |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Cut off battery power immediately or after the host has shut down. |
| * |
| * return EC_RES_INVALID_COMMAND if unsupported by a board/battery. |
| * EC_RES_SUCCESS if the command was successful. |
| * EC_RES_ERROR if the cut off command failed. |
| */ |
| #define EC_CMD_BATTERY_CUT_OFF 0x0099 |
| |
| #define EC_BATTERY_CUTOFF_FLAG_AT_SHUTDOWN (1 << 0) |
| |
| struct __ec_align1 ec_params_battery_cutoff { |
| uint8_t flags; |
| }; |
| |
| /*****************************************************************************/ |
| /* USB port mux control. */ |
| |
| /* |
| * Switch USB mux or return to automatic switching. |
| */ |
| #define EC_CMD_USB_MUX 0x009A |
| |
| struct __ec_align1 ec_params_usb_mux { |
| uint8_t mux; |
| }; |
| |
| /*****************************************************************************/ |
| /* LDOs / FETs control. */ |
| |
| enum ec_ldo_state { |
| EC_LDO_STATE_OFF = 0, /* the LDO / FET is shut down */ |
| EC_LDO_STATE_ON = 1, /* the LDO / FET is ON / providing power */ |
| }; |
| |
| /* |
| * Switch on/off a LDO. |
| */ |
| #define EC_CMD_LDO_SET 0x009B |
| |
| struct __ec_align1 ec_params_ldo_set { |
| uint8_t index; |
| uint8_t state; |
| }; |
| |
| /* |
| * Get LDO state. |
| */ |
| #define EC_CMD_LDO_GET 0x009C |
| |
| struct __ec_align1 ec_params_ldo_get { |
| uint8_t index; |
| }; |
| |
| struct __ec_align1 ec_response_ldo_get { |
| uint8_t state; |
| }; |
| |
| /*****************************************************************************/ |
| /* Power info. */ |
| |
| /* |
| * Get power info. |
| */ |
| #define EC_CMD_POWER_INFO 0x009D |
| |
| struct __ec_align4 ec_response_power_info { |
| uint32_t usb_dev_type; |
| uint16_t voltage_ac; |
| uint16_t voltage_system; |
| uint16_t current_system; |
| uint16_t usb_current_limit; |
| }; |
| |
| /*****************************************************************************/ |
| /* I2C passthru command */ |
| |
| #define EC_CMD_I2C_PASSTHRU 0x009E |
| |
| /* Read data; if not present, message is a write */ |
| #define EC_I2C_FLAG_READ (1 << 15) |
| |
| /* Mask for address */ |
| #define EC_I2C_ADDR_MASK 0x3ff |
| |
| #define EC_I2C_STATUS_NAK (1 << 0) /* Transfer was not acknowledged */ |
| #define EC_I2C_STATUS_TIMEOUT (1 << 1) /* Timeout during transfer */ |
| |
| /* Any error */ |
| #define EC_I2C_STATUS_ERROR (EC_I2C_STATUS_NAK | EC_I2C_STATUS_TIMEOUT) |
| |
| struct __ec_align2 ec_params_i2c_passthru_msg { |
| uint16_t addr_flags; /* I2C slave address (7 or 10 bits) and flags */ |
| uint16_t len; /* Number of bytes to read or write */ |
| }; |
| |
| struct __ec_align2 ec_params_i2c_passthru { |
| uint8_t port; /* I2C port number */ |
| uint8_t num_msgs; /* Number of messages */ |
| struct ec_params_i2c_passthru_msg msg[]; |
| /* Data to write for all messages is concatenated here */ |
| }; |
| |
| struct __ec_align1 ec_response_i2c_passthru { |
| uint8_t i2c_status; /* Status flags (EC_I2C_STATUS_...) */ |
| uint8_t num_msgs; /* Number of messages processed */ |
| uint8_t data[]; /* Data read by messages concatenated here */ |
| }; |
| |
| /*****************************************************************************/ |
| /* Power button hang detect */ |
| |
| #define EC_CMD_HANG_DETECT 0x009F |
| |
| /* Reasons to start hang detection timer */ |
| /* Power button pressed */ |
| #define EC_HANG_START_ON_POWER_PRESS (1 << 0) |
| |
| /* Lid closed */ |
| #define EC_HANG_START_ON_LID_CLOSE (1 << 1) |
| |
| /* Lid opened */ |
| #define EC_HANG_START_ON_LID_OPEN (1 << 2) |
| |
| /* Start of AP S3->S0 transition (booting or resuming from suspend) */ |
| #define EC_HANG_START_ON_RESUME (1 << 3) |
| |
| /* Reasons to cancel hang detection */ |
| |
| /* Power button released */ |
| #define EC_HANG_STOP_ON_POWER_RELEASE (1 << 8) |
| |
| /* Any host command from AP received */ |
| #define EC_HANG_STOP_ON_HOST_COMMAND (1 << 9) |
| |
| /* Stop on end of AP S0->S3 transition (suspending or shutting down) */ |
| #define EC_HANG_STOP_ON_SUSPEND (1 << 10) |
| |
| /* |
| * If this flag is set, all the other fields are ignored, and the hang detect |
| * timer is started. This provides the AP a way to start the hang timer |
| * without reconfiguring any of the other hang detect settings. Note that |
| * you must previously have configured the timeouts. |
| */ |
| #define EC_HANG_START_NOW (1 << 30) |
| |
| /* |
| * If this flag is set, all the other fields are ignored (including |
| * EC_HANG_START_NOW). This provides the AP a way to stop the hang timer |
| * without reconfiguring any of the other hang detect settings. |
| */ |
| #define EC_HANG_STOP_NOW (1 << 31) |
| |
| struct __ec_align4 ec_params_hang_detect { |
| /* Flags; see EC_HANG_* */ |
| uint32_t flags; |
| |
| /* Timeout in msec before generating host event, if enabled */ |
| uint16_t host_event_timeout_msec; |
| |
| /* Timeout in msec before generating warm reboot, if enabled */ |
| uint16_t warm_reboot_timeout_msec; |
| }; |
| |
| /*****************************************************************************/ |
| /* Commands for battery charging */ |
| |
| /* |
| * This is the single catch-all host command to exchange data regarding the |
| * charge state machine (v2 and up). |
| */ |
| #define EC_CMD_CHARGE_STATE 0x00A0 |
| |
| /* Subcommands for this host command */ |
| enum charge_state_command { |
| CHARGE_STATE_CMD_GET_STATE, |
| CHARGE_STATE_CMD_GET_PARAM, |
| CHARGE_STATE_CMD_SET_PARAM, |
| CHARGE_STATE_NUM_CMDS |
| }; |
| |
| /* |
| * Known param numbers are defined here. Ranges are reserved for board-specific |
| * params, which are handled by the particular implementations. |
| */ |
| enum charge_state_params { |
| CS_PARAM_CHG_VOLTAGE, /* charger voltage limit */ |
| CS_PARAM_CHG_CURRENT, /* charger current limit */ |
| CS_PARAM_CHG_INPUT_CURRENT, /* charger input current limit */ |
| CS_PARAM_CHG_STATUS, /* charger-specific status */ |
| CS_PARAM_CHG_OPTION, /* charger-specific options */ |
| CS_PARAM_LIMIT_POWER, /* |
| * Check if power is limited due to |
| * low battery and / or a weak external |
| * charger. READ ONLY. |
| */ |
| /* How many so far? */ |
| CS_NUM_BASE_PARAMS, |
| |
| /* Range for CONFIG_CHARGER_PROFILE_OVERRIDE params */ |
| CS_PARAM_CUSTOM_PROFILE_MIN = 0x10000, |
| CS_PARAM_CUSTOM_PROFILE_MAX = 0x1ffff, |
| |
| /* Other custom param ranges go here... */ |
| }; |
| |
| struct __ec_todo_packed ec_params_charge_state { |
| uint8_t cmd; /* enum charge_state_command */ |
| union { |
| struct __ec_align1 { |
| /* no args */ |
| } get_state; |
| |
| struct __ec_todo_unpacked { |
| uint32_t param; /* enum charge_state_param */ |
| } get_param; |
| |
| struct __ec_todo_unpacked { |
| uint32_t param; /* param to set */ |
| uint32_t value; /* value to set */ |
| } set_param; |
| }; |
| }; |
| |
| struct __ec_align4 ec_response_charge_state { |
| union { |
| struct __ec_align4 { |
| int ac; |
| int chg_voltage; |
| int chg_current; |
| int chg_input_current; |
| int batt_state_of_charge; |
| } get_state; |
| |
| struct __ec_align4 { |
| uint32_t value; |
| } get_param; |
| struct __ec_align4 { |
| /* no return values */ |
| } set_param; |
| }; |
| }; |
| |
| |
| /* |
| * Set maximum battery charging current. |
| */ |
| #define EC_CMD_CHARGE_CURRENT_LIMIT 0x00A1 |
| |
| struct __ec_align4 ec_params_current_limit { |
| uint32_t limit; /* in mA */ |
| }; |
| |
| /* |
| * Set maximum external voltage / current. |
| */ |
| #define EC_CMD_EXTERNAL_POWER_LIMIT 0x00A2 |
| |
| /* Command v0 is used only on Spring and is obsolete + unsupported */ |
| struct __ec_align2 ec_params_external_power_limit_v1 { |
| uint16_t current_lim; /* in mA, or EC_POWER_LIMIT_NONE to clear limit */ |
| uint16_t voltage_lim; /* in mV, or EC_POWER_LIMIT_NONE to clear limit */ |
| }; |
| |
| #define EC_POWER_LIMIT_NONE 0xffff |
| |
| /* |
| * Set maximum voltage & current of a dedicated charge port |
| */ |
| #define EC_CMD_OVERRIDE_DEDICATED_CHARGER_LIMIT 0x00A3 |
| |
| struct __ec_align2 ec_params_dedicated_charger_limit { |
| uint16_t current_lim; /* in mA */ |
| uint16_t voltage_lim; /* in mV */ |
| }; |
| |
| /*****************************************************************************/ |
| /* Hibernate/Deep Sleep Commands */ |
| |
| /* Set the delay before going into hibernation. */ |
| #define EC_CMD_HIBERNATION_DELAY 0x00A8 |
| |
| struct __ec_align4 ec_params_hibernation_delay { |
| /* |
| * Seconds to wait in G3 before hibernate. Pass in 0 to read the |
| * current settings without changing them. |
| */ |
| uint32_t seconds; |
| }; |
| |
| struct __ec_align4 ec_response_hibernation_delay { |
| /* |
| * The current time in seconds in which the system has been in the G3 |
| * state. This value is reset if the EC transitions out of G3. |
| */ |
| uint32_t time_g3; |
| |
| /* |
| * The current time remaining in seconds until the EC should hibernate. |
| * This value is also reset if the EC transitions out of G3. |
| */ |
| uint32_t time_remaining; |
| |
| /* |
| * The current time in seconds that the EC should wait in G3 before |
| * hibernating. |
| */ |
| uint32_t hibernate_delay; |
| }; |
| |
| /* Inform the EC when entering a sleep state */ |
| #define EC_CMD_HOST_SLEEP_EVENT 0x00A9 |
| |
| enum host_sleep_event { |
| HOST_SLEEP_EVENT_S3_SUSPEND = 1, |
| HOST_SLEEP_EVENT_S3_RESUME = 2, |
| HOST_SLEEP_EVENT_S0IX_SUSPEND = 3, |
| HOST_SLEEP_EVENT_S0IX_RESUME = 4 |
| }; |
| |
| struct __ec_align1 ec_params_host_sleep_event { |
| uint8_t sleep_event; |
| }; |
| |
| /*****************************************************************************/ |
| /* Device events */ |
| #define EC_CMD_DEVICE_EVENT 0x00AA |
| |
| enum ec_device_event { |
| EC_DEVICE_EVENT_TRACKPAD, |
| EC_DEVICE_EVENT_DSP, |
| EC_DEVICE_EVENT_WIFI, |
| }; |
| |
| enum ec_device_event_param { |
| /* Get and clear pending device events */ |
| EC_DEVICE_EVENT_PARAM_GET_CURRENT_EVENTS, |
| /* Get device event mask */ |
| EC_DEVICE_EVENT_PARAM_GET_ENABLED_EVENTS, |
| /* Set device event mask */ |
| EC_DEVICE_EVENT_PARAM_SET_ENABLED_EVENTS, |
| }; |
| |
| #define EC_DEVICE_EVENT_MASK(event_code) (1UL << (event_code % 32)) |
| |
| struct __ec_align_size1 ec_params_device_event { |
| uint32_t event_mask; |
| uint8_t param; |
| }; |
| |
| struct __ec_align4 ec_response_device_event { |
| uint32_t event_mask; |
| }; |
| |
| /*****************************************************************************/ |
| /* Smart battery pass-through */ |
| |
| /* Get / Set 16-bit smart battery registers */ |
| #define EC_CMD_SB_READ_WORD 0x00B0 |
| #define EC_CMD_SB_WRITE_WORD 0x00B1 |
| |
| /* Get / Set string smart battery parameters |
| * formatted as SMBUS "block". |
| */ |
| #define EC_CMD_SB_READ_BLOCK 0x00B2 |
| #define EC_CMD_SB_WRITE_BLOCK 0x00B3 |
| |
| struct __ec_align1 ec_params_sb_rd { |
| uint8_t reg; |
| }; |
| |
| struct __ec_align2 ec_response_sb_rd_word { |
| uint16_t value; |
| }; |
| |
| struct __ec_align1 ec_params_sb_wr_word { |
| uint8_t reg; |
| uint16_t value; |
| }; |
| |
| struct __ec_align1 ec_response_sb_rd_block { |
| uint8_t data[32]; |
| }; |
| |
| struct __ec_align1 ec_params_sb_wr_block { |
| uint8_t reg; |
| uint16_t data[32]; |
| }; |
| |
| /*****************************************************************************/ |
| /* Battery vendor parameters |
| * |
| * Get or set vendor-specific parameters in the battery. Implementations may |
| * differ between boards or batteries. On a set operation, the response |
| * contains the actual value set, which may be rounded or clipped from the |
| * requested value. |
| */ |
| |
| #define EC_CMD_BATTERY_VENDOR_PARAM 0x00B4 |
| |
| enum ec_battery_vendor_param_mode { |
| BATTERY_VENDOR_PARAM_MODE_GET = 0, |
| BATTERY_VENDOR_PARAM_MODE_SET, |
| }; |
| |
| struct __ec_align_size1 ec_params_battery_vendor_param { |
| uint32_t param; |
| uint32_t value; |
| uint8_t mode; |
| }; |
| |
| struct __ec_align4 ec_response_battery_vendor_param { |
| uint32_t value; |
| }; |
| |
| /*****************************************************************************/ |
| /* |
| * Smart Battery Firmware Update Commands |
| */ |
| #define EC_CMD_SB_FW_UPDATE 0x00B5 |
| |
| enum ec_sb_fw_update_subcmd { |
| EC_SB_FW_UPDATE_PREPARE = 0x0, |
| EC_SB_FW_UPDATE_INFO = 0x1, /*query sb info */ |
| EC_SB_FW_UPDATE_BEGIN = 0x2, /*check if protected */ |
| EC_SB_FW_UPDATE_WRITE = 0x3, /*check if protected */ |
| EC_SB_FW_UPDATE_END = 0x4, |
| EC_SB_FW_UPDATE_STATUS = 0x5, |
| EC_SB_FW_UPDATE_PROTECT = 0x6, |
| EC_SB_FW_UPDATE_MAX = 0x7, |
| }; |
| |
| #define SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE 32 |
| #define SB_FW_UPDATE_CMD_STATUS_SIZE 2 |
| #define SB_FW_UPDATE_CMD_INFO_SIZE 8 |
| |
| struct __ec_align4 ec_sb_fw_update_header { |
| uint16_t subcmd; /* enum ec_sb_fw_update_subcmd */ |
| uint16_t fw_id; /* firmware id */ |
| }; |
| |
| struct __ec_align4 ec_params_sb_fw_update { |
| struct ec_sb_fw_update_header hdr; |
| union { |
| /* EC_SB_FW_UPDATE_PREPARE = 0x0 */ |
| /* EC_SB_FW_UPDATE_INFO = 0x1 */ |
| /* EC_SB_FW_UPDATE_BEGIN = 0x2 */ |
| /* EC_SB_FW_UPDATE_END = 0x4 */ |
| /* EC_SB_FW_UPDATE_STATUS = 0x5 */ |
| /* EC_SB_FW_UPDATE_PROTECT = 0x6 */ |
| struct __ec_align4 { |
| /* no args */ |
| } dummy; |
| |
| /* EC_SB_FW_UPDATE_WRITE = 0x3 */ |
| struct __ec_align4 { |
| uint8_t data[SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE]; |
| } write; |
| }; |
| }; |
| |
| struct __ec_align1 ec_response_sb_fw_update { |
| union { |
| /* EC_SB_FW_UPDATE_INFO = 0x1 */ |
| struct __ec_align1 { |
| uint8_t data[SB_FW_UPDATE_CMD_INFO_SIZE]; |
| } info; |
| |
| /* EC_SB_FW_UPDATE_STATUS = 0x5 */ |
| struct __ec_align1 { |
| uint8_t data[SB_FW_UPDATE_CMD_STATUS_SIZE]; |
| } status; |
| }; |
| }; |
| |
| /* |
| * Entering Verified Boot Mode Command |
| * Default mode is VBOOT_MODE_NORMAL if EC did not receive this command. |
| * Valid Modes are: normal, developer, and recovery. |
| */ |
| #define EC_CMD_ENTERING_MODE 0x00B6 |
| |
| struct __ec_align4 ec_params_entering_mode { |
| int vboot_mode; |
| }; |
| |
| #define VBOOT_MODE_NORMAL 0 |
| #define VBOOT_MODE_DEVELOPER 1 |
| #define VBOOT_MODE_RECOVERY 2 |
| |
| /*****************************************************************************/ |
| /* |
| * I2C passthru protection command: Protects I2C tunnels against access on |
| * certain addresses (board-specific). |
| */ |
| #define EC_CMD_I2C_PASSTHRU_PROTECT 0x00B7 |
| |
| enum ec_i2c_passthru_protect_subcmd { |
| EC_CMD_I2C_PASSTHRU_PROTECT_STATUS = 0x0, |
| EC_CMD_I2C_PASSTHRU_PROTECT_ENABLE = 0x1, |
| }; |
| |
| struct __ec_align1 ec_params_i2c_passthru_protect { |
| uint8_t subcmd; |
| uint8_t port; /* I2C port number */ |
| }; |
| |
| struct __ec_align1 ec_response_i2c_passthru_protect { |
| uint8_t status; /* Status flags (0: unlocked, 1: locked) */ |
| }; |
| |
| /*****************************************************************************/ |
| /* System commands */ |
| |
| /* |
| * TODO(crosbug.com/p/23747): This is a confusing name, since it doesn't |
| * necessarily reboot the EC. Rename to "image" or something similar? |
| */ |
| #define EC_CMD_REBOOT_EC 0x00D2 |
| |
| /* Command */ |
| enum ec_reboot_cmd { |
| EC_REBOOT_CANCEL = 0, /* Cancel a pending reboot */ |
| EC_REBOOT_JUMP_RO = 1, /* Jump to RO without rebooting */ |
| EC_REBOOT_JUMP_RW = 2, /* Jump to RW without rebooting */ |
| /* (command 3 was jump to RW-B) */ |
| EC_REBOOT_COLD = 4, /* Cold-reboot */ |
| EC_REBOOT_DISABLE_JUMP = 5, /* Disable jump until next reboot */ |
| EC_REBOOT_HIBERNATE = 6, /* Hibernate EC */ |
| EC_REBOOT_HIBERNATE_CLEAR_AP_OFF = 7, /* and clears AP_OFF flag */ |
| }; |
| |
| /* Flags for ec_params_reboot_ec.reboot_flags */ |
| #define EC_REBOOT_FLAG_RESERVED0 (1 << 0) /* Was recovery request */ |
| #define EC_REBOOT_FLAG_ON_AP_SHUTDOWN (1 << 1) /* Reboot after AP shutdown */ |
| #define EC_REBOOT_FLAG_SWITCH_RW_SLOT (1 << 2) /* Switch RW slot */ |
| |
| struct __ec_align1 ec_params_reboot_ec { |
| uint8_t cmd; /* enum ec_reboot_cmd */ |
| uint8_t flags; /* See EC_REBOOT_FLAG_* */ |
| }; |
| |
| /* |
| * Get information on last EC panic. |
| * |
| * Returns variable-length platform-dependent panic information. See panic.h |
| * for details. |
| */ |
| #define EC_CMD_GET_PANIC_INFO 0x00D3 |
| |
| /*****************************************************************************/ |
| /* |
| * Special commands |
| * |
| * These do not follow the normal rules for commands. See each command for |
| * details. |
| */ |
| |
| /* |
| * Reboot NOW |
| * |
| * This command will work even when the EC LPC interface is busy, because the |
| * reboot command is processed at interrupt level. Note that when the EC |
| * reboots, the host will reboot too, so there is no response to this command. |
| * |
| * Use EC_CMD_REBOOT_EC to reboot the EC more politely. |
| */ |
| #define EC_CMD_REBOOT 0x00D1 /* Think "die" */ |
| |
| /* |
| * Resend last response (not supported on LPC). |
| * |
| * Returns EC_RES_UNAVAILABLE if there is no response available - for example, |
| * there was no previous command, or the previous command's response was too |
| * big to save. |
| */ |
| #define EC_CMD_RESEND_RESPONSE 0x00DB |
| |
| /* |
| * This header byte on a command indicate version 0. Any header byte less |
| * than this means that we are talking to an old EC which doesn't support |
| * versioning. In that case, we assume version 0. |
| * |
| * Header bytes greater than this indicate a later version. For example, |
| * EC_CMD_VERSION0 + 1 means we are using version 1. |
| * |
| * The old EC interface must not use commands 0xdc or higher. |
| */ |
| #define EC_CMD_VERSION0 0x00DC |
| |
| /*****************************************************************************/ |
| /* |
| * PD commands |
| * |
| * These commands are for PD MCU communication. |
| */ |
| |
| /* EC to PD MCU exchange status command */ |
| #define EC_CMD_PD_EXCHANGE_STATUS 0x0100 |
| #define EC_VER_PD_EXCHANGE_STATUS 2 |
| |
| enum pd_charge_state { |
| PD_CHARGE_NO_CHANGE = 0, /* Don't change charge state */ |
| PD_CHARGE_NONE, /* No charging allowed */ |
| PD_CHARGE_5V, /* 5V charging only */ |
| PD_CHARGE_MAX /* Charge at max voltage */ |
| }; |
| |
| /* Status of EC being sent to PD */ |
| #define EC_STATUS_HIBERNATING (1 << 0) |
| |
| struct __ec_align1 ec_params_pd_status { |
| uint8_t status; /* EC status */ |
| int8_t batt_soc; /* battery state of charge */ |
| uint8_t charge_state; /* charging state (from enum pd_charge_state) */ |
| }; |
| |
| /* Status of PD being sent back to EC */ |
| #define PD_STATUS_HOST_EVENT (1 << 0) /* Forward host event to AP */ |
| #define PD_STATUS_IN_RW (1 << 1) /* Running RW image */ |
| #define PD_STATUS_JUMPED_TO_IMAGE (1 << 2) /* Current image was jumped to */ |
| #define PD_STATUS_TCPC_ALERT_0 (1 << 3) /* Alert active in port 0 TCPC */ |
| #define PD_STATUS_TCPC_ALERT_1 (1 << 4) /* Alert active in port 1 TCPC */ |
| #define PD_STATUS_TCPC_ALERT_2 (1 << 5) /* Alert active in port 2 TCPC */ |
| #define PD_STATUS_TCPC_ALERT_3 (1 << 6) /* Alert active in port 3 TCPC */ |
| #define PD_STATUS_EC_INT_ACTIVE (PD_STATUS_TCPC_ALERT_0 | \ |
| PD_STATUS_TCPC_ALERT_1 | \ |
| PD_STATUS_HOST_EVENT) |
| struct __ec_align_size1 ec_response_pd_status { |
| uint32_t curr_lim_ma; /* input current limit */ |
| uint16_t status; /* PD MCU status */ |
| int8_t active_charge_port; /* active charging port */ |
| }; |
| |
| /* AP to PD MCU host event status command, cleared on read */ |
| #define EC_CMD_PD_HOST_EVENT_STATUS 0x0104 |
| |
| /* PD MCU host event status bits */ |
| #define PD_EVENT_UPDATE_DEVICE (1 << 0) |
| #define PD_EVENT_POWER_CHANGE (1 << 1) |
| #define PD_EVENT_IDENTITY_RECEIVED (1 << 2) |
| #define PD_EVENT_DATA_SWAP (1 << 3) |
| struct __ec_align4 ec_response_host_event_status { |
| uint32_t status; /* PD MCU host event status */ |
| }; |
| |
| /* Set USB type-C port role and muxes */ |
| #define EC_CMD_USB_PD_CONTROL 0x0101 |
| |
| enum usb_pd_control_role { |
| USB_PD_CTRL_ROLE_NO_CHANGE = 0, |
| USB_PD_CTRL_ROLE_TOGGLE_ON = 1, /* == AUTO */ |
| USB_PD_CTRL_ROLE_TOGGLE_OFF = 2, |
| USB_PD_CTRL_ROLE_FORCE_SINK = 3, |
| USB_PD_CTRL_ROLE_FORCE_SOURCE = 4, |
| USB_PD_CTRL_ROLE_COUNT |
| }; |
| |
| enum usb_pd_control_mux { |
| USB_PD_CTRL_MUX_NO_CHANGE = 0, |
| USB_PD_CTRL_MUX_NONE = 1, |
| USB_PD_CTRL_MUX_USB = 2, |
| USB_PD_CTRL_MUX_DP = 3, |
| USB_PD_CTRL_MUX_DOCK = 4, |
| USB_PD_CTRL_MUX_AUTO = 5, |
| USB_PD_CTRL_MUX_COUNT |
| }; |
| |
| enum usb_pd_control_swap { |
| USB_PD_CTRL_SWAP_NONE = 0, |
| USB_PD_CTRL_SWAP_DATA = 1, |
| USB_PD_CTRL_SWAP_POWER = 2, |
| USB_PD_CTRL_SWAP_VCONN = 3, |
| USB_PD_CTRL_SWAP_COUNT |
| }; |
| |
| struct __ec_align1 ec_params_usb_pd_control { |
| uint8_t port; |
| uint8_t role; |
| uint8_t mux; |
| uint8_t swap; |
| }; |
| |
| #define PD_CTRL_RESP_ENABLED_COMMS (1 << 0) /* Communication enabled */ |
| #define PD_CTRL_RESP_ENABLED_CONNECTED (1 << 1) /* Device connected */ |
| #define PD_CTRL_RESP_ENABLED_PD_CAPABLE (1 << 2) /* Partner is PD capable */ |
| |
| #define PD_CTRL_RESP_ROLE_POWER (1 << 0) /* 0=SNK/1=SRC */ |
| #define PD_CTRL_RESP_ROLE_DATA (1 << 1) /* 0=UFP/1=DFP */ |
| #define PD_CTRL_RESP_ROLE_VCONN (1 << 2) /* Vconn status */ |
| #define PD_CTRL_RESP_ROLE_DR_POWER (1 << 3) /* Partner is dualrole power */ |
| #define PD_CTRL_RESP_ROLE_DR_DATA (1 << 4) /* Partner is dualrole data */ |
| #define PD_CTRL_RESP_ROLE_USB_COMM (1 << 5) /* Partner USB comm capable */ |
| #define PD_CTRL_RESP_ROLE_EXT_POWERED (1 << 6) /* Partner externally powerd */ |
| |
| struct __ec_align1 ec_response_usb_pd_control { |
| uint8_t enabled; |
| uint8_t role; |
| uint8_t polarity; |
| uint8_t state; |
| }; |
| |
| struct __ec_align1 ec_response_usb_pd_control_v1 { |
| uint8_t enabled; |
| uint8_t role; |
| uint8_t polarity; |
| char state[32]; |
| }; |
| |
| #define EC_CMD_USB_PD_PORTS 0x0102 |
| |
| /* Maximum number of PD ports on a device, num_ports will be <= this */ |
| #define EC_USB_PD_MAX_PORTS 8 |
| |
| struct __ec_align1 ec_response_usb_pd_ports { |
| uint8_t num_ports; |
| }; |
| |
| #define EC_CMD_USB_PD_POWER_INFO 0x0103 |
| |
| #define PD_POWER_CHARGING_PORT 0xff |
| struct __ec_align1 ec_params_usb_pd_power_info { |
| uint8_t port; |
| }; |
| |
| enum usb_chg_type { |
| USB_CHG_TYPE_NONE, |
| USB_CHG_TYPE_PD, |
| USB_CHG_TYPE_C, |
| USB_CHG_TYPE_PROPRIETARY, |
| USB_CHG_TYPE_BC12_DCP, |
| USB_CHG_TYPE_BC12_CDP, |
| USB_CHG_TYPE_BC12_SDP, |
| USB_CHG_TYPE_OTHER, |
| USB_CHG_TYPE_VBUS, |
| USB_CHG_TYPE_UNKNOWN, |
| }; |
| enum usb_power_roles { |
| USB_PD_PORT_POWER_DISCONNECTED, |
| USB_PD_PORT_POWER_SOURCE, |
| USB_PD_PORT_POWER_SINK, |
| USB_PD_PORT_POWER_SINK_NOT_CHARGING, |
| }; |
| |
| struct __ec_align2 usb_chg_measures { |
| uint16_t voltage_max; |
| uint16_t voltage_now; |
| uint16_t current_max; |
| uint16_t current_lim; |
| }; |
| |
| struct __ec_align4 ec_response_usb_pd_power_info { |
| uint8_t role; |
| uint8_t type; |
| uint8_t dualrole; |
| uint8_t reserved1; |
| struct usb_chg_measures meas; |
| uint32_t max_power; |
| }; |
| |
| /* Write USB-PD device FW */ |
| #define EC_CMD_USB_PD_FW_UPDATE 0x0110 |
| |
| enum usb_pd_fw_update_cmds { |
| USB_PD_FW_REBOOT, |
| USB_PD_FW_FLASH_ERASE, |
| USB_PD_FW_FLASH_WRITE, |
| USB_PD_FW_ERASE_SIG, |
| }; |
| |
| struct __ec_align4 ec_params_usb_pd_fw_update { |
| uint16_t dev_id; |
| uint8_t cmd; |
| uint8_t port; |
| uint32_t size; /* Size to write in bytes */ |
| /* Followed by data to write */ |
| }; |
| |
| /* Write USB-PD Accessory RW_HASH table entry */ |
| #define EC_CMD_USB_PD_RW_HASH_ENTRY 0x0111 |
| /* RW hash is first 20 bytes of SHA-256 of RW section */ |
| #define PD_RW_HASH_SIZE 20 |
| struct __ec_align1 ec_params_usb_pd_rw_hash_entry { |
| uint16_t dev_id; |
| uint8_t dev_rw_hash[PD_RW_HASH_SIZE]; |
| uint8_t reserved; /* For alignment of current_image |
| * TODO(rspangler) but it's not aligned! |
| * Should have been reserved[2]. */ |
| uint32_t current_image; /* One of ec_current_image */ |
| }; |
| |
| /* Read USB-PD Accessory info */ |
| #define EC_CMD_USB_PD_DEV_INFO 0x0112 |
| |
| struct __ec_align1 ec_params_usb_pd_info_request { |
| uint8_t port; |
| }; |
| |
| /* Read USB-PD Device discovery info */ |
| #define EC_CMD_USB_PD_DISCOVERY 0x0113 |
| struct __ec_align_size1 ec_params_usb_pd_discovery_entry { |
| uint16_t vid; /* USB-IF VID */ |
| uint16_t pid; /* USB-IF PID */ |
| uint8_t ptype; /* product type (hub,periph,cable,ama) */ |
| }; |
| |
| /* Override default charge behavior */ |
| #define EC_CMD_PD_CHARGE_PORT_OVERRIDE 0x0114 |
| |
| /* Negative port parameters have special meaning */ |
| enum usb_pd_override_ports { |
| OVERRIDE_DONT_CHARGE = -2, |
| OVERRIDE_OFF = -1, |
| /* [0, CONFIG_USB_PD_PORT_COUNT): Port# */ |
| }; |
| |
| struct __ec_align2 ec_params_charge_port_override { |
| int16_t override_port; /* Override port# */ |
| }; |
| |
| /* Read (and delete) one entry of PD event log */ |
| #define EC_CMD_PD_GET_LOG_ENTRY 0x0115 |
| |
| struct __ec_align4 ec_response_pd_log { |
| uint32_t timestamp; /* relative timestamp in milliseconds */ |
| uint8_t type; /* event type : see PD_EVENT_xx below */ |
| uint8_t size_port; /* [7:5] port number [4:0] payload size in bytes */ |
| uint16_t data; /* type-defined data payload */ |
| uint8_t payload[0]; /* optional additional data payload: 0..16 bytes */ |
| }; |
| |
| |
| /* The timestamp is the microsecond counter shifted to get about a ms. */ |
| #define PD_LOG_TIMESTAMP_SHIFT 10 /* 1 LSB = 1024us */ |
| |
| #define PD_LOG_SIZE_MASK 0x1f |
| #define PD_LOG_PORT_MASK 0xe0 |
| #define PD_LOG_PORT_SHIFT 5 |
| #define PD_LOG_PORT_SIZE(port, size) (((port) << PD_LOG_PORT_SHIFT) | \ |
| ((size) & PD_LOG_SIZE_MASK)) |
| #define PD_LOG_PORT(size_port) ((size_port) >> PD_LOG_PORT_SHIFT) |
| #define PD_LOG_SIZE(size_port) ((size_port) & PD_LOG_SIZE_MASK) |
| |
| /* PD event log : entry types */ |
| /* PD MCU events */ |
| #define PD_EVENT_MCU_BASE 0x00 |
| #define PD_EVENT_MCU_CHARGE (PD_EVENT_MCU_BASE+0) |
| #define PD_EVENT_MCU_CONNECT (PD_EVENT_MCU_BASE+1) |
| /* Reserved for custom board event */ |
| #define PD_EVENT_MCU_BOARD_CUSTOM (PD_EVENT_MCU_BASE+2) |
| /* PD generic accessory events */ |
| #define PD_EVENT_ACC_BASE 0x20 |
| #define PD_EVENT_ACC_RW_FAIL (PD_EVENT_ACC_BASE+0) |
| #define PD_EVENT_ACC_RW_ERASE (PD_EVENT_ACC_BASE+1) |
| /* PD power supply events */ |
| #define PD_EVENT_PS_BASE 0x40 |
| #define PD_EVENT_PS_FAULT (PD_EVENT_PS_BASE+0) |
| /* PD video dongles events */ |
| #define PD_EVENT_VIDEO_BASE 0x60 |
| #define PD_EVENT_VIDEO_DP_MODE (PD_EVENT_VIDEO_BASE+0) |
| #define PD_EVENT_VIDEO_CODEC (PD_EVENT_VIDEO_BASE+1) |
| /* Returned in the "type" field, when there is no entry available */ |
| #define PD_EVENT_NO_ENTRY 0xff |
| |
| /* |
| * PD_EVENT_MCU_CHARGE event definition : |
| * the payload is "struct usb_chg_measures" |
| * the data field contains the port state flags as defined below : |
| */ |
| /* Port partner is a dual role device */ |
| #define CHARGE_FLAGS_DUAL_ROLE (1 << 15) |
| /* Port is the pending override port */ |
| #define CHARGE_FLAGS_DELAYED_OVERRIDE (1 << 14) |
| /* Port is the override port */ |
| #define CHARGE_FLAGS_OVERRIDE (1 << 13) |
| /* Charger type */ |
| #define CHARGE_FLAGS_TYPE_SHIFT 3 |
| #define CHARGE_FLAGS_TYPE_MASK (0xf << CHARGE_FLAGS_TYPE_SHIFT) |
| /* Power delivery role */ |
| #define CHARGE_FLAGS_ROLE_MASK (7 << 0) |
| |
| /* |
| * PD_EVENT_PS_FAULT data field flags definition : |
| */ |
| #define PS_FAULT_OCP 1 |
| #define PS_FAULT_FAST_OCP 2 |
| #define PS_FAULT_OVP 3 |
| #define PS_FAULT_DISCH 4 |
| |
| /* |
| * PD_EVENT_VIDEO_CODEC payload is "struct mcdp_info". |
| */ |
| struct __ec_align4 mcdp_version { |
| uint8_t major; |
| uint8_t minor; |
| uint16_t build; |
| }; |
| |
| struct __ec_align4 mcdp_info { |
| uint8_t family[2]; |
| uint8_t chipid[2]; |
| struct mcdp_version irom; |
| struct mcdp_version fw; |
| }; |
| |
| /* struct mcdp_info field decoding */ |
| #define MCDP_CHIPID(chipid) ((chipid[0] << 8) | chipid[1]) |
| #define MCDP_FAMILY(family) ((family[0] << 8) | family[1]) |
| |
| /* Get/Set USB-PD Alternate mode info */ |
| #define EC_CMD_USB_PD_GET_AMODE 0x0116 |
| struct __ec_align_size1 ec_params_usb_pd_get_mode_request { |
| uint16_t svid_idx; /* SVID index to get */ |
| uint8_t port; /* port */ |
| }; |
| |
| struct __ec_align4 ec_params_usb_pd_get_mode_response { |
| uint16_t svid; /* SVID */ |
| uint16_t opos; /* Object Position */ |
| uint32_t vdo[6]; /* Mode VDOs */ |
| }; |
| |
| #define EC_CMD_USB_PD_SET_AMODE 0x0117 |
| |
| enum pd_mode_cmd { |
| PD_EXIT_MODE = 0, |
| PD_ENTER_MODE = 1, |
| /* Not a command. Do NOT remove. */ |
| PD_MODE_CMD_COUNT, |
| }; |
| |
| struct __ec_align4 ec_params_usb_pd_set_mode_request { |
| uint32_t cmd; /* enum pd_mode_cmd */ |
| uint16_t svid; /* SVID to set */ |
| uint8_t opos; /* Object Position */ |
| uint8_t port; /* port */ |
| }; |
| |
| /* Ask the PD MCU to record a log of a requested type */ |
| #define EC_CMD_PD_WRITE_LOG_ENTRY 0x0118 |
| |
| struct __ec_align1 ec_params_pd_write_log_entry { |
| uint8_t type; /* event type : see PD_EVENT_xx above */ |
| uint8_t port; /* port#, or 0 for events unrelated to a given port */ |
| }; |
| |
| |
| /* Control USB-PD chip */ |
| #define EC_CMD_PD_CONTROL 0x0119 |
| |
| enum ec_pd_control_cmd { |
| PD_SUSPEND = 0, /* Suspend the PD chip (EC: stop talking to PD) */ |
| PD_RESUME, /* Resume the PD chip (EC: start talking to PD) */ |
| PD_RESET, /* Force reset the PD chip */ |
| PD_CONTROL_DISABLE /* Disable further calls to this command */ |
| }; |
| |
| struct __ec_align1 ec_params_pd_control { |
| uint8_t chip; /* chip id (should be 0) */ |
| uint8_t subcmd; |
| }; |
| |
| /* Get info about USB-C SS muxes */ |
| #define EC_CMD_USB_PD_MUX_INFO 0x011A |
| |
| struct __ec_align1 ec_params_usb_pd_mux_info { |
| uint8_t port; /* USB-C port number */ |
| }; |
| |
| /* Flags representing mux state */ |
| #define USB_PD_MUX_USB_ENABLED (1 << 0) |
| #define USB_PD_MUX_DP_ENABLED (1 << 1) |
| #define USB_PD_MUX_POLARITY_INVERTED (1 << 2) |
| #define USB_PD_MUX_HPD_IRQ (1 << 3) |
| |
| struct __ec_align1 ec_response_usb_pd_mux_info { |
| uint8_t flags; /* USB_PD_MUX_*-encoded USB mux state */ |
| }; |
| |
| #define EC_CMD_PD_CHIP_INFO 0x011B |
| |
| struct __ec_align1 ec_params_pd_chip_info { |
| uint8_t port; /* USB-C port number */ |
| uint8_t renew; /* Force renewal */ |
| }; |
| |
| struct __ec_align2 ec_response_pd_chip_info { |
| uint16_t vendor_id; |
| uint16_t product_id; |
| uint16_t device_id; |
| union { |
| uint8_t fw_version_string[8]; |
| uint64_t fw_version_number; |
| }; |
| }; |
| |
| /* Run RW signature verification and get status */ |
| #define EC_CMD_RWSIG_CHECK_STATUS 0x011C |
| |
| struct __ec_align4 ec_response_rwsig_check_status { |
| uint32_t status; |
| }; |
| |
| /* For controlling RWSIG task */ |
| #define EC_CMD_RWSIG_ACTION 0x011D |
| |
| enum rwsig_action { |
| RWSIG_ACTION_ABORT = 0, /* Abort RWSIG and prevent jumping */ |
| RWSIG_ACTION_CONTINUE = 1, /* Jump to RW immediately */ |
| }; |
| |
| struct __ec_align4 ec_params_rwsig_action { |
| uint32_t action; |
| }; |
| |
| /* Run verification on a slot */ |
| #define EC_CMD_EFS_VERIFY 0x011E |
| |
| struct __ec_align1 ec_params_efs_verify { |
| uint8_t region; /* enum ec_flash_region */ |
| }; |
| |
| /* |
| * Retrieve info from Cros Board Info store. Response is based on the data |
| * type. Integers return a uint32. Strings return a string, using the response |
| * size to determine how big it is. |
| */ |
| #define EC_CMD_GET_CROS_BOARD_INFO 0x011F |
| /* |
| * Write info into Cros Board Info on EEPROM. Write fails if the board has |
| * hardware write-protect enabled. |
| */ |
| #define EC_CMD_SET_CROS_BOARD_INFO 0x0120 |
| |
| enum cbi_data_tag { |
| CBI_TAG_BOARD_VERSION = 0, /* uint16_t or uint8_t[] = {minor,major} */ |
| CBI_TAG_OEM_ID = 1, /* uint8_t */ |
| CBI_TAG_SKU_ID = 2, /* uint8_t */ |
| CBI_TAG_COUNT, |
| }; |
| |
| /* |
| * Flags to control read operation |
| * |
| * RELOAD: Invalidate cache and read data from EEPROM. Useful to verify |
| * write was successful without reboot. |
| */ |
| #define CBI_GET_RELOAD (1 << 0) |
| |
| struct __ec_align4 ec_params_get_cbi { |
| uint32_t type; /* enum cbi_data_tag */ |
| uint32_t flag; /* CBI_GET_* */ |
| }; |
| |
| /* |
| * Flags to control write behavior. |
| * |
| * NO_SYNC: Makes EC update data in RAM but skip writing to EEPROM. It's |
| * useful when writing multiple fields in a row. |
| * INIT: Needs to be set when creating a new CBI from scratch. All fields |
| * will be initialized to zero first. |
| */ |
| #define CBI_SET_NO_SYNC (1 << 0) |
| #define CBI_SET_INIT (1 << 1) |
| |
| struct __ec_align1 ec_params_set_cbi { |
| uint32_t tag; /* enum cbi_data_tag */ |
| uint32_t flag; /* CBI_SET_* */ |
| uint32_t size; /* Data size */ |
| uint8_t data[]; /* For string and raw data */ |
| }; |
| |
| /*****************************************************************************/ |
| /* The command range 0x200-0x2FF is reserved for Rotor. */ |
| |
| /*****************************************************************************/ |
| /* |
| * Reserve a range of host commands for the CR51 firmware. |
| */ |
| #define EC_CMD_CR51_BASE 0x0300 |
| #define EC_CMD_CR51_LAST 0x03FF |
| |
| /*****************************************************************************/ |
| /* Fingerprint MCU commands: range 0x0400-0x040x */ |
| |
| /* Fingerprint SPI sensor passthru command: prototyping ONLY */ |
| #define EC_CMD_FP_PASSTHRU 0x0400 |
| |
| #define EC_FP_FLAG_NOT_COMPLETE 0x1 |
| |
| struct __ec_align2 ec_params_fp_passthru { |
| uint16_t len; /* Number of bytes to write then read */ |
| uint16_t flags; /* EC_FP_FLAG_xxx */ |
| uint8_t data[]; /* Data to send */ |
| }; |
| |
| /* Fingerprint sensor configuration command: prototyping ONLY */ |
| #define EC_CMD_FP_SENSOR_CONFIG 0x0401 |
| |
| #define EC_FP_SENSOR_CONFIG_MAX_REGS 16 |
| |
| struct __ec_align2 ec_params_fp_sensor_config { |
| uint8_t count; /* Number of setup registers */ |
| /* |
| * the value to send to each of the 'count' setup registers |
| * is stored in the 'data' array for 'len' bytes just after |
| * the previous one. |
| */ |
| uint8_t len[EC_FP_SENSOR_CONFIG_MAX_REGS]; |
| uint8_t data[]; |
| }; |
| |
| /* Configure the Fingerprint MCU behavior */ |
| #define EC_CMD_FP_MODE 0x0402 |
| |
| /* Put the sensor in its lowest power mode */ |
| #define FP_MODE_DEEPSLEEP (1<<0) |
| /* Wait to see a finger on the sensor */ |
| #define FP_MODE_FINGER_DOWN (1<<1) |
| /* Poll until the finger has left the sensor */ |
| #define FP_MODE_FINGER_UP (1<<2) |
| /* Capture the current finger image */ |
| #define FP_MODE_CAPTURE (1<<3) |
| /* special value: don't change anything just read back current mode */ |
| #define FP_MODE_DONT_CHANGE (1<<31) |
| |
| struct __ec_align4 ec_params_fp_mode { |
| uint32_t mode; /* as defined by FP_MODE_ constants */ |
| /* TBD */ |
| }; |
| |
| struct __ec_align4 ec_response_fp_mode { |
| uint32_t mode; /* as defined by FP_MODE_ constants */ |
| /* TBD */ |
| }; |
| |
| /* Retrieve Fingerprint sensor information */ |
| #define EC_CMD_FP_INFO 0x0403 |
| |
| struct __ec_align2 ec_response_fp_info { |
| /* Sensor identification */ |
| uint32_t vendor_id; |
| uint32_t product_id; |
| uint32_t model_id; |
| uint32_t version; |
| /* Image frame characteristics */ |
| uint32_t frame_size; |
| uint32_t pixel_format; /* using V4L2_PIX_FMT_ */ |
| uint16_t width; |
| uint16_t height; |
| uint16_t bpp; |
| }; |
| |
| /* Get the last captured finger frame: TODO: will be AES-encrypted */ |
| #define EC_CMD_FP_FRAME 0x0404 |
| |
| struct __ec_align4 ec_params_fp_frame { |
| uint32_t offset; |
| uint32_t size; |
| }; |
| |
| /*****************************************************************************/ |
| /* Touchpad MCU commands: range 0x0500-0x05FF */ |
| |
| /* Perform touchpad self test */ |
| #define EC_CMD_TP_SELF_TEST 0x0500 |
| |
| /* Get number of frame types, and the size of each type */ |
| #define EC_CMD_TP_FRAME_INFO 0x0501 |
| |
| struct __ec_align4 ec_response_tp_frame_info { |
| uint32_t n_frames; |
| uint32_t frame_sizes[0]; |
| }; |
| |
| /* Create a snapshot of current frame readings */ |
| #define EC_CMD_TP_FRAME_SNAPSHOT 0x0502 |
| |
| /* Read the frame */ |
| #define EC_CMD_TP_FRAME_GET 0x0503 |
| |
| struct __ec_align4 ec_params_tp_frame_get { |
| uint32_t frame_index; |
| uint32_t offset; |
| uint32_t size; |
| }; |
| |
| /*****************************************************************************/ |
| /* |
| * Reserve a range of host commands for board-specific, experimental, or |
| * special purpose features. These can be (re)used without updating this file. |
| * |
| * CAUTION: Don't go nuts with this. Shipping products should document ALL |
| * their EC commands for easier development, testing, debugging, and support. |
| * |
| * All commands MUST be #defined to be 4-digit UPPER CASE hex values |
| * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work. |
| * |
| * In your experimental code, you may want to do something like this: |
| * |
| * #define EC_CMD_MAGIC_FOO 0x0000 |
| * #define EC_CMD_MAGIC_BAR 0x0001 |
| * #define EC_CMD_MAGIC_HEY 0x0002 |
| * |
| * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_FOO, magic_foo_handler, |
| * EC_VER_MASK(0); |
| * |
| * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_BAR, magic_bar_handler, |
| * EC_VER_MASK(0); |
| * |
| * DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_HEY, magic_hey_handler, |
| * EC_VER_MASK(0); |
| */ |
| #define EC_CMD_BOARD_SPECIFIC_BASE 0x3E00 |
| #define EC_CMD_BOARD_SPECIFIC_LAST 0x3FFF |
| |
| /* |
| * Given the private host command offset, calculate the true private host |
| * command value. |
| */ |
| #define EC_PRIVATE_HOST_COMMAND_VALUE(command) \ |
| (EC_CMD_BOARD_SPECIFIC_BASE + (command)) |
| |
| /*****************************************************************************/ |
| /* |
| * Passthru commands |
| * |
| * Some platforms have sub-processors chained to each other. For example. |
| * |
| * AP <--> EC <--> PD MCU |
| * |
| * The top 2 bits of the command number are used to indicate which device the |
| * command is intended for. Device 0 is always the device receiving the |
| * command; other device mapping is board-specific. |
| * |
| * When a device receives a command to be passed to a sub-processor, it passes |
| * it on with the device number set back to 0. This allows the sub-processor |
| * to remain blissfully unaware of whether the command originated on the next |
| * device up the chain, or was passed through from the AP. |
| * |
| * In the above example, if the AP wants to send command 0x0002 to the PD MCU, |
| * AP sends command 0x4002 to the EC |
| * EC sends command 0x0002 to the PD MCU |
| * EC forwards PD MCU response back to the AP |
| */ |
| |
| /* Offset and max command number for sub-device n */ |
| #define EC_CMD_PASSTHRU_OFFSET(n) (0x4000 * (n)) |
| #define EC_CMD_PASSTHRU_MAX(n) (EC_CMD_PASSTHRU_OFFSET(n) + 0x3fff) |
| |
| /*****************************************************************************/ |
| /* |
| * Deprecated constants. These constants have been renamed for clarity. The |
| * meaning and size has not changed. Programs that use the old names should |
| * switch to the new names soon, as the old names may not be carried forward |
| * forever. |
| */ |
| #define EC_HOST_PARAM_SIZE EC_PROTO2_MAX_PARAM_SIZE |
| #define EC_LPC_ADDR_OLD_PARAM EC_HOST_CMD_REGION1 |
| #define EC_OLD_PARAM_SIZE EC_HOST_CMD_REGION_SIZE |
| |
| #endif /* !__ACPI__ && !__KERNEL__ */ |
| |
| #endif /* __CROS_EC_COMMANDS_H */ |