blob: 9576bc1a20c1b2196618e46fd930c9e7ea02e117 [file] [log] [blame]
/*
* (C) Copyright 2012-2012 Henrik Nordstrom <henrik@henriknordstrom.net>
*
* (C) Copyright 2007-2011
* Allwinner Technology Co., Ltd. <www.allwinnertech.com>
* Tom Cubie <tangliang@allwinnertech.com>
*
* Configuration settings for the Allwinner sunxi series of boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SUNXI_COMMON_CONFIG_H
#define _SUNXI_COMMON_CONFIG_H
#include <linux/stringify.h>
#ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT
/*
* The U-Boot workarounds bugs in the outdated buggy sunxi-3.4 kernels at the
* expense of restricting some features, so the regular machine id values can
* be used.
*/
# define CONFIG_MACH_TYPE_COMPAT_REV 0
#else
/*
* A compatibility guard to prevent loading outdated buggy sunxi-3.4 kernels.
* Only sunxi-3.4 kernels with appropriate fixes applied are able to pass
* beyond the machine id check.
*/
# define CONFIG_MACH_TYPE_COMPAT_REV 1
#endif
/*
* High Level Configuration Options
*/
#define CONFIG_SUNXI /* sunxi family */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_THUMB_BUILD /* Thumbs mode to save space in SPL */
#endif
#include <asm/arch/cpu.h> /* get chip and board defs */
#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_DM_SERIAL)
# define CONFIG_DW_SERIAL
#endif
/*
* Display CPU information
*/
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_SYS_PROMPT "sunxi# "
/* Serial & console */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
/* ns16550 reg in the low bits of cpu reg */
#define CONFIG_SYS_NS16550_CLK 24000000
#ifndef CONFIG_DM_SERIAL
# define CONFIG_SYS_NS16550_REG_SIZE -4
# define CONFIG_SYS_NS16550_COM1 SUNXI_UART0_BASE
# define CONFIG_SYS_NS16550_COM2 SUNXI_UART1_BASE
# define CONFIG_SYS_NS16550_COM3 SUNXI_UART2_BASE
# define CONFIG_SYS_NS16550_COM4 SUNXI_UART3_BASE
# define CONFIG_SYS_NS16550_COM5 SUNXI_R_UART_BASE
#endif
/* CPU */
#define CONFIG_SYS_CACHELINE_SIZE 64
/*
* The DRAM Base differs between some models. We cannot use macros for the
* CONFIG_FOO defines which contain the DRAM base address since they end
* up unexpanded in include/autoconf.mk .
*
* So we have to have this #ifdef #else #endif block for these.
*/
#ifdef CONFIG_MACH_SUN9I
#define SDRAM_OFFSET(x) 0x2##x
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* default load address */
#define CONFIG_SYS_TEXT_BASE 0x2a000000
#define CONFIG_PRE_CON_BUF_ADDR 0x2f000000
#define CONFIG_SYS_SPL_MALLOC_START 0x2ff00000
#define CONFIG_SPL_BSS_START_ADDR 0x2ff80000
#else
#define SDRAM_OFFSET(x) 0x4##x
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define CONFIG_SYS_LOAD_ADDR 0x42000000 /* default load address */
#define CONFIG_SYS_TEXT_BASE 0x4a000000
#define CONFIG_PRE_CON_BUF_ADDR 0x4f000000
#define CONFIG_SYS_SPL_MALLOC_START 0x4ff00000
#define CONFIG_SPL_BSS_START_ADDR 0x4ff80000
#endif
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000 /* 512 KiB */
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000 /* 512 KiB */
#ifdef CONFIG_MACH_SUN9I
/*
* The A80's A1 sram starts at 0x00010000 rather then at 0x00000000 and is
* slightly bigger. Note that it is possible to map the first 32 KiB of the
* A1 at 0x00000000 like with older SoCs by writing 0x16aa0001 to the
* undocumented 0x008000e0 SYS_CTRL register. Where the 16aa is a key and
* the 1 actually activates the mapping of the first 32 KiB to 0x00000000.
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x10000
#define CONFIG_SYS_INIT_RAM_SIZE 0x0a000 /* 40 KiB */
#else
#define CONFIG_SYS_INIT_RAM_ADDR 0x0
#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* 32 KiB */
#endif
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_0 CONFIG_SYS_SDRAM_BASE
#define PHYS_SDRAM_0_SIZE 0x80000000 /* 2 GiB */
#ifdef CONFIG_AHCI
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SUNXI_AHCI
#define CONFIG_SYS_64BIT_LBA
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_CMD_SCSI
#endif
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_CMDLINE_TAG
#define CONFIG_INITRD_TAG
#define CONFIG_SERIAL_TAG
/* mmc config */
#if !defined(CONFIG_UART0_PORT_F)
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_CMD_MMC
#define CONFIG_MMC_SUNXI
#define CONFIG_MMC_SUNXI_SLOT 0
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0 /* first detected MMC controller */
#endif
/* 4MB of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_GENERIC_BOARD
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* standalone support */
#define CONFIG_STANDALONE_LOAD_ADDR CONFIG_SYS_LOAD_ADDR
/* baudrate */
#define CONFIG_BAUDRATE 115200
/* The stack sizes are set up in start.S using the settings below */
#define CONFIG_STACKSIZE (256 << 10) /* 256 KiB */
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* 512 KiB */
#define CONFIG_IDENT_STRING " Allwinner Technology"
#define CONFIG_ENV_OFFSET (544 << 10) /* (8 + 24 + 512) KiB */
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_FAT_WRITE /* enable write access */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_BOARD_LOAD_IMAGE
#define CONFIG_SPL_TEXT_BASE 0x20 /* sram start+header */
#define CONFIG_SPL_MAX_SIZE 0x5fe0 /* 24KB on sun4i/sun7i */
#define CONFIG_SPL_LIBDISK_SUPPORT
#if !defined(CONFIG_UART0_PORT_F)
#define CONFIG_SPL_MMC_SUPPORT
#endif
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/sunxi/u-boot-spl.lds"
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 80 /* 40KiB */
#define CONFIG_SPL_PAD_TO 32768 /* decimal for 'dd' */
/* end of 32 KiB in sram */
#define LOW_LEVEL_SRAM_STACK 0x00008000 /* End of sram */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
/* I2C */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER
#define CONFIG_SPL_I2C_SUPPORT
#endif
#if defined CONFIG_I2C0_ENABLE || defined CONFIG_I2C1_ENABLE || \
defined CONFIG_I2C2_ENABLE || defined CONFIG_I2C3_ENABLE || \
defined CONFIG_I2C4_ENABLE
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_SYS_I2C_SPEED 400000
#define CONFIG_SYS_I2C_SLAVE 0x7f
#define CONFIG_CMD_I2C
#endif
#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x00
/* We use pin names in Kconfig and sunxi_name_to_gpio() */
#define CONFIG_SOFT_I2C_GPIO_SDA soft_i2c_gpio_sda
#define CONFIG_SOFT_I2C_GPIO_SCL soft_i2c_gpio_scl
#ifndef __ASSEMBLY__
extern int soft_i2c_gpio_sda;
extern int soft_i2c_gpio_scl;
#endif
#define CONFIG_VIDEO_LCD_I2C_BUS 0 /* The lcd panel soft i2c is bus 0 */
#define CONFIG_SYS_SPD_BUS_NUM 1 /* And the axp209 i2c bus is bus 1 */
#else
#define CONFIG_SYS_SPD_BUS_NUM 0 /* The axp209 i2c bus is bus 0 */
#define CONFIG_VIDEO_LCD_I2C_BUS -1 /* NA, but necessary to compile */
#endif
/* PMU */
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || defined CONFIG_AXP221_POWER
#define CONFIG_SPL_POWER_SUPPORT
#endif
#ifndef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX 1 /* UART0 */
#endif
#if CONFIG_CONS_INDEX == 1
#ifdef CONFIG_MACH_SUN9I
#define OF_STDOUT_PATH "/soc/serial@07000000:115200"
#else
#define OF_STDOUT_PATH "/soc@01c00000/serial@01c28000:115200"
#endif
#elif CONFIG_CONS_INDEX == 2 && defined(CONFIG_MACH_SUN5I)
#define OF_STDOUT_PATH "/soc@01c00000/serial@01c28400:115200"
#elif CONFIG_CONS_INDEX == 3 && defined(CONFIG_MACH_SUN8I)
#define OF_STDOUT_PATH "/soc@01c00000/serial@01c28800:115200"
#elif CONFIG_CONS_INDEX == 5 && defined(CONFIG_MACH_SUN8I)
#define OF_STDOUT_PATH "/soc@01c00000/serial@01f02800:115200"
#else
#error Unsupported console port nr. Please fix stdout-path in sunxi-common.h.
#endif
/* GPIO */
#define CONFIG_SUNXI_GPIO
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_CMD_GPIO
#ifdef CONFIG_VIDEO
/*
* The amount of RAM to keep free at the top of RAM when relocating u-boot,
* to use as framebuffer. This must be a multiple of 4096.
*/
#define CONFIG_SUNXI_MAX_FB_SIZE (9 << 20)
/* Do we want to initialize a simple FB? */
#define CONFIG_VIDEO_DT_SIMPLEFB
#define CONFIG_VIDEO_SUNXI
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_STD_TIMINGS
#define CONFIG_I2C_EDID
/* allow both serial and cfb console. */
#define CONFIG_CONSOLE_MUX
/* stop x86 thinking in cfbconsole from trying to init a pc keyboard */
#define CONFIG_VGA_AS_SINGLE_DEVICE
/* To be able to hook simplefb into dt */
#ifdef CONFIG_VIDEO_DT_SIMPLEFB
#define CONFIG_OF_BOARD_SETUP
#endif
#endif /* CONFIG_VIDEO */
/* Ethernet support */
#ifdef CONFIG_SUNXI_EMAC
#define CONFIG_PHY_ADDR 1
#define CONFIG_MII /* MII PHY management */
#define CONFIG_PHYLIB
#endif
#ifdef CONFIG_SUNXI_GMAC
#define CONFIG_DW_AUTONEG
#define CONFIG_PHY_GIGE /* GMAC can use gigabit PHY */
#define CONFIG_PHY_ADDR 1
#define CONFIG_MII /* MII PHY management */
#define CONFIG_PHYLIB
#endif
#ifdef CONFIG_USB_EHCI
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_OHCI_SUNXI
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
#endif
#ifdef CONFIG_USB_MUSB_SUNXI
#define CONFIG_MUSB_HOST
#define CONFIG_MUSB_PIO_ONLY
#endif
#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_SUNXI
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#endif
#ifdef CONFIG_USB_KEYBOARD
#define CONFIG_CONSOLE_MUX
#define CONFIG_PREBOOT
#define CONFIG_SYS_STDIO_DEREGISTER
#define CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
#endif
#if !defined CONFIG_ENV_IS_IN_MMC && \
!defined CONFIG_ENV_IS_IN_NAND && \
!defined CONFIG_ENV_IS_IN_FAT && \
!defined CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_IS_NOWHERE
#endif
#define CONFIG_MISC_INIT_R
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#ifndef CONFIG_SPL_BUILD
#include <config_distro_defaults.h>
/* Enable pre-console buffer to get complete log on the VGA console */
#define CONFIG_PRE_CONSOLE_BUFFER
#define CONFIG_PRE_CON_BUF_SZ 4096 /* Aprox 2 80*25 screens */
/*
* 240M RAM (256M minimum minus space for the framebuffer),
* 32M uncompressed kernel, 16M compressed kernel, 1M fdt,
* 1M script, 1M pxe and the ramdisk at the end.
*/
#define MEM_LAYOUT_ENV_SETTINGS \
"bootm_size=0xf000000\0" \
"kernel_addr_r=" __stringify(SDRAM_OFFSET(2000000)) "\0" \
"fdt_addr_r=" __stringify(SDRAM_OFFSET(3000000)) "\0" \
"scriptaddr=" __stringify(SDRAM_OFFSET(3100000)) "\0" \
"pxefile_addr_r=" __stringify(SDRAM_OFFSET(3200000)) "\0" \
"ramdisk_addr_r=" __stringify(SDRAM_OFFSET(3300000)) "\0"
#ifdef CONFIG_MMC
#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
#else
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
#ifdef CONFIG_AHCI
#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
#else
#define BOOT_TARGET_DEVICES_SCSI(func)
#endif
#ifdef CONFIG_USB_EHCI
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_DEVICES_USB(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_MMC(func) \
BOOT_TARGET_DEVICES_SCSI(func) \
BOOT_TARGET_DEVICES_USB(func) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#ifdef CONFIG_USB_KEYBOARD
#define CONSOLE_STDIN_SETTINGS \
"preboot=usb start\0" \
"stdin=serial,usbkbd\0"
#else
#define CONSOLE_STDIN_SETTINGS \
"stdin=serial\0"
#endif
#ifdef CONFIG_VIDEO
#define CONSOLE_STDOUT_SETTINGS \
"stdout=serial,vga\0" \
"stderr=serial,vga\0"
#else
#define CONSOLE_STDOUT_SETTINGS \
"stdout=serial\0" \
"stderr=serial\0"
#endif
#define CONSOLE_ENV_SETTINGS \
CONSOLE_STDIN_SETTINGS \
CONSOLE_STDOUT_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
CONSOLE_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"console=ttyS0,115200\0" \
BOOTENV
#else /* ifndef CONFIG_SPL_BUILD */
#define CONFIG_EXTRA_ENV_SETTINGS
#endif
#endif /* _SUNXI_COMMON_CONFIG_H */