| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2017 Andes Technology Corporation |
| * Rick Chen, Andes Technology Corporation <rick@andestech.com> |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define RISCV_MMODE_TIMERBASE 0xe6000000 |
| #define RISCV_MMODE_TIMER_FREQ 60000000 |
| |
| #define RISCV_SMODE_TIMER_FREQ 60000000 |
| |
| /* |
| * CPU and Board Configuration Options |
| */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| /* |
| * Physical Memory Map |
| */ |
| #define PHYS_SDRAM_0 0x00000000 /* SDRAM Bank #1 */ |
| #define PHYS_SDRAM_1 \ |
| (PHYS_SDRAM_0 + PHYS_SDRAM_0_SIZE) /* SDRAM Bank #2 */ |
| #define PHYS_SDRAM_0_SIZE 0x20000000 /* 512 MB */ |
| #define PHYS_SDRAM_1_SIZE 0x20000000 /* 512 MB */ |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_0 |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #ifndef CONFIG_DM_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE -4 |
| #endif |
| #define CONFIG_SYS_NS16550_CLK 19660800 |
| |
| /* Init Stack Pointer */ |
| |
| /* support JEDEC */ |
| #define PHYS_FLASH_1 0x88000000 /* BANK 0 */ |
| #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, } |
| |
| /* max number of memory banks */ |
| /* |
| * There are 4 banks supported for this Controller, |
| * but we have only 1 bank connected to flash on board |
| */ |
| #define CONFIG_SYS_FLASH_BANKS_SIZES {0x4000000} |
| |
| /* max number of sectors on one chip */ |
| #define CONFIG_FLASH_SECTOR_SIZE (0x10000*2) |
| |
| /* environments */ |
| |
| /* SPI FLASH */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 16 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| |
| /* Initial Memory map for Linux*/ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) |
| /* Increase max gunzip size */ |
| |
| /* Support autoboot from RAM (kernel image is loaded via debug port) */ |
| #define KERNEL_IMAGE_ADDR "0x2000000 " |
| #define BOOTENV_DEV_NAME_RAM(devtypeu, devtypel, instance) \ |
| "ram " |
| #define BOOTENV_DEV_RAM(devtypeu, devtypel, instance) \ |
| "bootcmd_ram=" \ |
| "booti " \ |
| KERNEL_IMAGE_ADDR \ |
| "- $fdtcontroladdr\0" |
| |
| /* When we use RAM as ENV */ |
| |
| /* Enable distro boot */ |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(MMC, mmc, 0) \ |
| func(DHCP, dhcp, na) \ |
| func(RAM, ram, na) |
| #include <config_distro_bootcmd.h> |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "kernel_addr_r=0x00080000\0" \ |
| "pxefile_addr_r=0x01f00000\0" \ |
| "scriptaddr=0x01f00000\0" \ |
| "fdt_addr_r=0x02000000\0" \ |
| "ramdisk_addr_r=0x02800000\0" \ |
| BOOTENV |
| |
| #endif /* __CONFIG_H */ |