blob: 87bf105f385d4c12bee6d038c0ba50e2e588124c [file] [log] [blame]
/*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/dma.h>
#include <asm/mach-imx/hab.h>
#include <asm/mach-imx/rdc-sema.h>
#include <asm/arch/imx-rdc.h>
#include <asm/arch/crm_regs.h>
#include <dm.h>
#include <imx_thermal.h>
#if defined(CONFIG_IMX_THERMAL)
static const struct imx_thermal_plat imx7_thermal_plat = {
.regs = (void *)ANATOP_BASE_ADDR,
.fuse_bank = 3,
.fuse_word = 3,
};
U_BOOT_DEVICE(imx7_thermal) = {
.name = "imx_thermal",
.platdata = &imx7_thermal_plat,
};
#endif
#if CONFIG_IS_ENABLED(IMX_RDC)
/*
* In current design, if any peripheral was assigned to both A7 and M4,
* it will receive ipg_stop or ipg_wait when any of the 2 platforms enter
* low power mode. So M4 sleep will cause some peripherals fail to work
* at A7 core side. At default, all resources are in domain 0 - 3.
*
* There are 26 peripherals impacted by this IC issue:
* SIM2(sim2/emvsim2)
* SIM1(sim1/emvsim1)
* UART1/UART2/UART3/UART4/UART5/UART6/UART7
* SAI1/SAI2/SAI3
* WDOG1/WDOG2/WDOG3/WDOG4
* GPT1/GPT2/GPT3/GPT4
* PWM1/PWM2/PWM3/PWM4
* ENET1/ENET2
* Software Workaround:
* Here we setup some resources to domain 0 where M4 codes will move
* the M4 out of this domain. Then M4 is not able to access them any longer.
* This is a workaround for ic issue. So the peripherals are not shared
* by them. This way requires the uboot implemented the RDC driver and
* set the 26 IPs above to domain 0 only. M4 code will assign resource
* to its own domain, if it want to use the resource.
*/
static rdc_peri_cfg_t const resources[] = {
(RDC_PER_SIM1 | RDC_DOMAIN(0)),
(RDC_PER_SIM2 | RDC_DOMAIN(0)),
(RDC_PER_UART1 | RDC_DOMAIN(0)),
(RDC_PER_UART2 | RDC_DOMAIN(0)),
(RDC_PER_UART3 | RDC_DOMAIN(0)),
(RDC_PER_UART4 | RDC_DOMAIN(0)),
(RDC_PER_UART5 | RDC_DOMAIN(0)),
(RDC_PER_UART6 | RDC_DOMAIN(0)),
(RDC_PER_UART7 | RDC_DOMAIN(0)),
(RDC_PER_SAI1 | RDC_DOMAIN(0)),
(RDC_PER_SAI2 | RDC_DOMAIN(0)),
(RDC_PER_SAI3 | RDC_DOMAIN(0)),
(RDC_PER_WDOG1 | RDC_DOMAIN(0)),
(RDC_PER_WDOG2 | RDC_DOMAIN(0)),
(RDC_PER_WDOG3 | RDC_DOMAIN(0)),
(RDC_PER_WDOG4 | RDC_DOMAIN(0)),
(RDC_PER_GPT1 | RDC_DOMAIN(0)),
(RDC_PER_GPT2 | RDC_DOMAIN(0)),
(RDC_PER_GPT3 | RDC_DOMAIN(0)),
(RDC_PER_GPT4 | RDC_DOMAIN(0)),
(RDC_PER_PWM1 | RDC_DOMAIN(0)),
(RDC_PER_PWM2 | RDC_DOMAIN(0)),
(RDC_PER_PWM3 | RDC_DOMAIN(0)),
(RDC_PER_PWM4 | RDC_DOMAIN(0)),
(RDC_PER_ENET1 | RDC_DOMAIN(0)),
(RDC_PER_ENET2 | RDC_DOMAIN(0)),
};
static void isolate_resource(void)
{
imx_rdc_setup_peripherals(resources, ARRAY_SIZE(resources));
}
#endif
#if defined(CONFIG_SECURE_BOOT)
struct imx_sec_config_fuse_t const imx_sec_config_fuse = {
.bank = 1,
.word = 3,
};
#endif
/*
* OCOTP_TESTER3[9:8] (see Fusemap Description Table offset 0x440)
* defines a 2-bit SPEED_GRADING
*/
#define OCOTP_TESTER3_SPEED_SHIFT 8
#define OCOTP_TESTER3_SPEED_800MHZ 0
#define OCOTP_TESTER3_SPEED_500MHZ 1
#define OCOTP_TESTER3_SPEED_1GHZ 2
#define OCOTP_TESTER3_SPEED_1P2GHZ 3
u32 get_cpu_speed_grade_hz(void)
{
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[1];
struct fuse_bank1_regs *fuse =
(struct fuse_bank1_regs *)bank->fuse_regs;
uint32_t val;
val = readl(&fuse->tester3);
val >>= OCOTP_TESTER3_SPEED_SHIFT;
val &= 0x3;
switch(val) {
case OCOTP_TESTER3_SPEED_800MHZ:
return 800000000;
case OCOTP_TESTER3_SPEED_500MHZ:
return 500000000;
case OCOTP_TESTER3_SPEED_1GHZ:
return 1000000000;
case OCOTP_TESTER3_SPEED_1P2GHZ:
return 1200000000;
}
return 0;
}
/*
* OCOTP_TESTER3[7:6] (see Fusemap Description Table offset 0x440)
* defines a 2-bit SPEED_GRADING
*/
#define OCOTP_TESTER3_TEMP_SHIFT 6
u32 get_cpu_temp_grade(int *minc, int *maxc)
{
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[1];
struct fuse_bank1_regs *fuse =
(struct fuse_bank1_regs *)bank->fuse_regs;
uint32_t val;
val = readl(&fuse->tester3);
val >>= OCOTP_TESTER3_TEMP_SHIFT;
val &= 0x3;
if (minc && maxc) {
if (val == TEMP_AUTOMOTIVE) {
*minc = -40;
*maxc = 125;
} else if (val == TEMP_INDUSTRIAL) {
*minc = -40;
*maxc = 105;
} else if (val == TEMP_EXTCOMMERCIAL) {
*minc = -20;
*maxc = 105;
} else {
*minc = 0;
*maxc = 95;
}
}
return val;
}
static bool is_mx7d(void)
{
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[1];
struct fuse_bank1_regs *fuse =
(struct fuse_bank1_regs *)bank->fuse_regs;
int val;
val = readl(&fuse->tester4);
if (val & 1)
return false;
else
return true;
}
u32 get_cpu_rev(void)
{
struct mxc_ccm_anatop_reg *ccm_anatop = (struct mxc_ccm_anatop_reg *)
ANATOP_BASE_ADDR;
u32 reg = readl(&ccm_anatop->digprog);
u32 type = (reg >> 16) & 0xff;
if (!is_mx7d())
type = MXC_CPU_MX7S;
reg &= 0xff;
return (type << 12) | reg;
}
#ifdef CONFIG_REVISION_TAG
u32 __weak get_board_rev(void)
{
return get_cpu_rev();
}
#endif
/* enable all periherial can be accessed in nosec mode */
static void init_csu(void)
{
int i = 0;
for (i = 0; i < CSU_NUM_REGS; i++)
writel(CSU_INIT_SEC_LEVEL0, CSU_IPS_BASE_ADDR + i * 4);
}
static void imx_enet_mdio_fixup(void)
{
struct iomuxc_gpr_base_regs *gpr_regs =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
/*
* The management data input/output (MDIO) requires open-drain,
* i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
* this feature. So to TO1.1, need to enable open drain by setting
* bits GPR0[8:7].
*/
if (soc_rev() >= CHIP_REV_1_1) {
setbits_le32(&gpr_regs->gpr[0],
IOMUXC_GPR_GPR0_ENET_MDIO_OPEN_DRAIN_MASK);
}
}
int arch_cpu_init(void)
{
init_aips();
init_csu();
/* Disable PDE bit of WMCR register */
imx_set_wdog_powerdown(false);
imx_enet_mdio_fixup();
#ifdef CONFIG_APBH_DMA
/* Start APBH DMA */
mxs_dma_init();
#endif
#if CONFIG_IS_ENABLED(IMX_RDC)
isolate_resource();
#endif
return 0;
}
#ifdef CONFIG_ARCH_MISC_INIT
int arch_misc_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
if (is_mx7d())
env_set("soc", "imx7d");
else
env_set("soc", "imx7s");
#endif
return 0;
}
#endif
#ifdef CONFIG_SERIAL_TAG
void get_board_serial(struct tag_serialnr *serialnr)
{
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[0];
struct fuse_bank0_regs *fuse =
(struct fuse_bank0_regs *)bank->fuse_regs;
serialnr->low = fuse->tester0;
serialnr->high = fuse->tester1;
}
#endif
#if defined(CONFIG_FEC_MXC)
void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
{
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[9];
struct fuse_bank9_regs *fuse =
(struct fuse_bank9_regs *)bank->fuse_regs;
if (0 == dev_id) {
u32 value = readl(&fuse->mac_addr1);
mac[0] = (value >> 8);
mac[1] = value;
value = readl(&fuse->mac_addr0);
mac[2] = value >> 24;
mac[3] = value >> 16;
mac[4] = value >> 8;
mac[5] = value;
} else {
u32 value = readl(&fuse->mac_addr2);
mac[0] = value >> 24;
mac[1] = value >> 16;
mac[2] = value >> 8;
mac[3] = value;
value = readl(&fuse->mac_addr1);
mac[4] = value >> 24;
mac[5] = value >> 16;
}
}
#endif
#ifdef CONFIG_IMX_BOOTAUX
int arch_auxiliary_core_up(u32 core_id, u32 boot_private_data)
{
u32 stack, pc;
struct src *src_reg = (struct src *)SRC_BASE_ADDR;
if (!boot_private_data)
return 1;
stack = *(u32 *)boot_private_data;
pc = *(u32 *)(boot_private_data + 4);
/* Set the stack and pc to M4 bootROM */
writel(stack, M4_BOOTROM_BASE_ADDR);
writel(pc, M4_BOOTROM_BASE_ADDR + 4);
/* Enable M4 */
clrsetbits_le32(&src_reg->m4rcr, SRC_M4RCR_M4C_NON_SCLR_RST_MASK,
SRC_M4RCR_ENABLE_M4_MASK);
return 0;
}
int arch_auxiliary_core_check_up(u32 core_id)
{
uint32_t val;
struct src *src_reg = (struct src *)SRC_BASE_ADDR;
val = readl(&src_reg->m4rcr);
if (val & 0x00000001)
return 0; /* assert in reset */
return 1;
}
#endif
void set_wdog_reset(struct wdog_regs *wdog)
{
u32 reg = readw(&wdog->wcr);
/*
* Output WDOG_B signal to reset external pmic or POR_B decided by
* the board desgin. Without external reset, the peripherals/DDR/
* PMIC are not reset, that may cause system working abnormal.
*/
reg = readw(&wdog->wcr);
reg |= 1 << 3;
/*
* WDZST bit is write-once only bit. Align this bit in kernel,
* otherwise kernel code will have no chance to set this bit.
*/
reg |= 1 << 0;
writew(reg, &wdog->wcr);
}
/*
* cfg_val will be used for
* Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
* After reset, if GPR10[28] is 1, ROM will copy GPR9[25:0]
* to SBMR1, which will determine the boot device.
*/
const struct boot_mode soc_boot_modes[] = {
{"ecspi1:0", MAKE_CFGVAL(0x00, 0x60, 0x00, 0x00)},
{"ecspi1:1", MAKE_CFGVAL(0x40, 0x62, 0x00, 0x00)},
{"ecspi1:2", MAKE_CFGVAL(0x80, 0x64, 0x00, 0x00)},
{"ecspi1:3", MAKE_CFGVAL(0xc0, 0x66, 0x00, 0x00)},
{"weim", MAKE_CFGVAL(0x00, 0x50, 0x00, 0x00)},
{"qspi1", MAKE_CFGVAL(0x10, 0x40, 0x00, 0x00)},
/* 4 bit bus width */
{"usdhc1", MAKE_CFGVAL(0x10, 0x10, 0x00, 0x00)},
{"usdhc2", MAKE_CFGVAL(0x10, 0x14, 0x00, 0x00)},
{"usdhc3", MAKE_CFGVAL(0x10, 0x18, 0x00, 0x00)},
{"mmc1", MAKE_CFGVAL(0x10, 0x20, 0x00, 0x00)},
{"mmc2", MAKE_CFGVAL(0x10, 0x24, 0x00, 0x00)},
{"mmc3", MAKE_CFGVAL(0x10, 0x28, 0x00, 0x00)},
{NULL, 0},
};
enum boot_device get_boot_device(void)
{
struct bootrom_sw_info **p =
(struct bootrom_sw_info **)ROM_SW_INFO_ADDR;
enum boot_device boot_dev = SD1_BOOT;
u8 boot_type = (*p)->boot_dev_type;
u8 boot_instance = (*p)->boot_dev_instance;
switch (boot_type) {
case BOOT_TYPE_SD:
boot_dev = boot_instance + SD1_BOOT;
break;
case BOOT_TYPE_MMC:
boot_dev = boot_instance + MMC1_BOOT;
break;
case BOOT_TYPE_NAND:
boot_dev = NAND_BOOT;
break;
case BOOT_TYPE_QSPI:
boot_dev = QSPI_BOOT;
break;
case BOOT_TYPE_WEIM:
boot_dev = WEIM_NOR_BOOT;
break;
case BOOT_TYPE_SPINOR:
boot_dev = SPI_NOR_BOOT;
break;
default:
break;
}
return boot_dev;
}
#ifdef CONFIG_ENV_IS_IN_MMC
__weak int board_mmc_get_env_dev(int devno)
{
return CONFIG_SYS_MMC_ENV_DEV;
}
int mmc_get_env_dev(void)
{
struct bootrom_sw_info **p =
(struct bootrom_sw_info **)ROM_SW_INFO_ADDR;
int devno = (*p)->boot_dev_instance;
u8 boot_type = (*p)->boot_dev_type;
/* If not boot from sd/mmc, use default value */
if ((boot_type != BOOT_TYPE_SD) && (boot_type != BOOT_TYPE_MMC))
return CONFIG_SYS_MMC_ENV_DEV;
return board_mmc_get_env_dev(devno);
}
#endif
void s_init(void)
{
#if !defined CONFIG_SPL_BUILD
/* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
asm volatile(
"mrc p15, 0, r0, c1, c0, 1\n"
"orr r0, r0, #1 << 6\n"
"mcr p15, 0, r0, c1, c0, 1\n");
#endif
/* clock configuration. */
clock_init();
return;
}
void reset_misc(void)
{
#ifdef CONFIG_VIDEO_MXS
lcdif_power_down();
#endif
}