blob: f07669374d703673a4961a22c8bcf9ef99bf497f [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* PCIe driver for Marvell MVEBU SoCs
*
* Based on Barebox drivers/pci/pci-mvebu.c
*
* Ported to U-Boot by:
* Anton Schubert <anton.schubert@gmx.de>
* Stefan Roese <sr@denx.de>
* Pali Rohár <pali@kernel.org>
*/
#include <common.h>
#include <dm.h>
#include <log.h>
#include <malloc.h>
#include <dm/device-internal.h>
#include <dm/lists.h>
#include <dm/of_access.h>
#include <pci.h>
#include <reset.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/mbus.h>
#include <linux/sizes.h>
/* PCIe unit register offsets */
#define MVPCIE_ROOT_PORT_PCI_CFG_OFF 0x0000
#define MVPCIE_ROOT_PORT_PCI_EXP_OFF 0x0060
#define MVPCIE_BAR_LO_OFF(n) (0x0010 + ((n) << 3))
#define MVPCIE_BAR_HI_OFF(n) (0x0014 + ((n) << 3))
#define MVPCIE_BAR_CTRL_OFF(n) (0x1804 + (((n) - 1) * 4))
#define MVPCIE_WIN04_CTRL_OFF(n) (0x1820 + ((n) << 4))
#define MVPCIE_WIN04_BASE_OFF(n) (0x1824 + ((n) << 4))
#define MVPCIE_WIN04_REMAP_OFF(n) (0x182c + ((n) << 4))
#define MVPCIE_WIN5_CTRL_OFF 0x1880
#define MVPCIE_WIN5_BASE_OFF 0x1884
#define MVPCIE_WIN5_REMAP_OFF 0x188c
#define MVPCIE_CONF_ADDR_OFF 0x18f8
#define MVPCIE_CONF_DATA_OFF 0x18fc
#define MVPCIE_CTRL_OFF 0x1a00
#define MVPCIE_CTRL_RC_MODE BIT(1)
#define MVPCIE_STAT_OFF 0x1a04
#define MVPCIE_STAT_BUS (0xff << 8)
#define MVPCIE_STAT_DEV (0x1f << 16)
#define MVPCIE_STAT_LINK_DOWN BIT(0)
#define LINK_WAIT_RETRIES 100
#define LINK_WAIT_TIMEOUT 1000
struct mvebu_pcie {
struct pci_controller hose;
void __iomem *base;
void __iomem *membase;
struct resource mem;
void __iomem *iobase;
struct resource io;
u32 intregs;
u32 port;
u32 lane;
bool is_x4;
int devfn;
int sec_busno;
char name[16];
unsigned int mem_target;
unsigned int mem_attr;
unsigned int io_target;
unsigned int io_attr;
u32 cfgcache[(0x3c - 0x10) / 4];
};
static inline bool mvebu_pcie_link_up(struct mvebu_pcie *pcie)
{
u32 val;
val = readl(pcie->base + MVPCIE_STAT_OFF);
return !(val & MVPCIE_STAT_LINK_DOWN);
}
static void mvebu_pcie_wait_for_link(struct mvebu_pcie *pcie)
{
int retries;
/* check if the link is up or not */
for (retries = 0; retries < LINK_WAIT_RETRIES; retries++) {
if (mvebu_pcie_link_up(pcie)) {
printf("%s: Link up\n", pcie->name);
return;
}
udelay(LINK_WAIT_TIMEOUT);
}
printf("%s: Link down\n", pcie->name);
}
static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie *pcie, int busno)
{
u32 stat;
stat = readl(pcie->base + MVPCIE_STAT_OFF);
stat &= ~MVPCIE_STAT_BUS;
stat |= busno << 8;
writel(stat, pcie->base + MVPCIE_STAT_OFF);
}
static void mvebu_pcie_set_local_dev_nr(struct mvebu_pcie *pcie, int devno)
{
u32 stat;
stat = readl(pcie->base + MVPCIE_STAT_OFF);
stat &= ~MVPCIE_STAT_DEV;
stat |= devno << 16;
writel(stat, pcie->base + MVPCIE_STAT_OFF);
}
static inline struct mvebu_pcie *hose_to_pcie(struct pci_controller *hose)
{
return container_of(hose, struct mvebu_pcie, hose);
}
static bool mvebu_pcie_valid_addr(struct mvebu_pcie *pcie,
int busno, int dev, int func)
{
/* On the root bus is only one PCI Bridge */
if (busno == 0 && (dev != 0 || func != 0))
return false;
/* Access to other buses is possible when link is up */
if (busno != 0 && !mvebu_pcie_link_up(pcie))
return false;
/* On secondary bus can be only one PCIe device */
if (busno == pcie->sec_busno && dev != 0)
return false;
return true;
}
static int mvebu_pcie_read_config(const struct udevice *bus, pci_dev_t bdf,
uint offset, ulong *valuep,
enum pci_size_t size)
{
struct mvebu_pcie *pcie = dev_get_plat(bus);
int busno = PCI_BUS(bdf) - dev_seq(bus);
u32 addr, data;
debug("PCIE CFG read: (b,d,f)=(%2d,%2d,%2d) ",
PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
if (!mvebu_pcie_valid_addr(pcie, busno, PCI_DEV(bdf), PCI_FUNC(bdf))) {
debug("- out of range\n");
*valuep = pci_get_ff(size);
return 0;
}
/*
* The configuration space of the PCI Bridge on the root bus (zero) is
* of Type 0 but the BAR registers (including ROM BAR) don't have the
* same meaning as in the PCIe specification. Therefore do not access
* BAR registers and non-common registers (those which have different
* meaning for Type 0 and Type 1 config space) of the PCI Bridge and
* instead read their content from driver virtual cfgcache[].
*/
if (busno == 0 && ((offset >= 0x10 && offset < 0x34) ||
(offset >= 0x38 && offset < 0x3c))) {
data = pcie->cfgcache[(offset - 0x10) / 4];
debug("(addr,size,val)=(0x%04x, %d, 0x%08x) from cfgcache\n",
offset, size, data);
*valuep = pci_conv_32_to_size(data, offset, size);
return 0;
}
/*
* PCI bridge is device 0 at the root bus (zero) but mvebu has it
* mapped on secondary bus with device number 1.
*/
if (busno == 0)
addr = PCI_CONF1_EXT_ADDRESS(pcie->sec_busno, 1, 0, offset);
else
addr = PCI_CONF1_EXT_ADDRESS(busno, PCI_DEV(bdf), PCI_FUNC(bdf), offset);
/* write address */
writel(addr, pcie->base + MVPCIE_CONF_ADDR_OFF);
/* read data */
switch (size) {
case PCI_SIZE_8:
data = readb(pcie->base + MVPCIE_CONF_DATA_OFF + (offset & 3));
break;
case PCI_SIZE_16:
data = readw(pcie->base + MVPCIE_CONF_DATA_OFF + (offset & 2));
break;
case PCI_SIZE_32:
data = readl(pcie->base + MVPCIE_CONF_DATA_OFF);
break;
default:
return -EINVAL;
}
if (busno == 0 && (offset & ~3) == (PCI_HEADER_TYPE & ~3)) {
/*
* Change Header Type of PCI Bridge device to Type 1
* (0x01, used by PCI Bridges) because mvebu reports
* Type 0 (0x00, used by Upstream and Endpoint devices).
*/
data = pci_conv_size_to_32(data, 0, offset, size);
data &= ~0x007f0000;
data |= PCI_HEADER_TYPE_BRIDGE << 16;
data = pci_conv_32_to_size(data, offset, size);
}
debug("(addr,size,val)=(0x%04x, %d, 0x%08x)\n", offset, size, data);
*valuep = data;
return 0;
}
static int mvebu_pcie_write_config(struct udevice *bus, pci_dev_t bdf,
uint offset, ulong value,
enum pci_size_t size)
{
struct mvebu_pcie *pcie = dev_get_plat(bus);
int busno = PCI_BUS(bdf) - dev_seq(bus);
u32 addr, data;
debug("PCIE CFG write: (b,d,f)=(%2d,%2d,%2d) ",
PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
debug("(addr,size,val)=(0x%04x, %d, 0x%08lx)\n", offset, size, value);
if (!mvebu_pcie_valid_addr(pcie, busno, PCI_DEV(bdf), PCI_FUNC(bdf))) {
debug("- out of range\n");
return 0;
}
/*
* As explained in mvebu_pcie_read_config(), PCI Bridge Type 1 specific
* config registers are not available, so we write their content only
* into driver virtual cfgcache[].
* And as explained in mvebu_pcie_probe(), mvebu has its own specific
* way for configuring secondary bus number.
*/
if (busno == 0 && ((offset >= 0x10 && offset < 0x34) ||
(offset >= 0x38 && offset < 0x3c))) {
debug("Writing to cfgcache only\n");
data = pcie->cfgcache[(offset - 0x10) / 4];
data = pci_conv_size_to_32(data, value, offset, size);
/* mvebu PCI bridge does not have configurable bars */
if ((offset & ~3) == PCI_BASE_ADDRESS_0 ||
(offset & ~3) == PCI_BASE_ADDRESS_1 ||
(offset & ~3) == PCI_ROM_ADDRESS1)
data = 0x0;
pcie->cfgcache[(offset - 0x10) / 4] = data;
/* mvebu has its own way how to set PCI secondary bus number */
if (offset == PCI_SECONDARY_BUS ||
(offset == PCI_PRIMARY_BUS && size != PCI_SIZE_8)) {
pcie->sec_busno = (data >> 8) & 0xff;
mvebu_pcie_set_local_bus_nr(pcie, pcie->sec_busno);
debug("Secondary bus number was changed to %d\n",
pcie->sec_busno);
}
return 0;
}
/*
* PCI bridge is device 0 at the root bus (zero) but mvebu has it
* mapped on secondary bus with device number 1.
*/
if (busno == 0)
addr = PCI_CONF1_EXT_ADDRESS(pcie->sec_busno, 1, 0, offset);
else
addr = PCI_CONF1_EXT_ADDRESS(busno, PCI_DEV(bdf), PCI_FUNC(bdf), offset);
/* write address */
writel(addr, pcie->base + MVPCIE_CONF_ADDR_OFF);
/* write data */
switch (size) {
case PCI_SIZE_8:
writeb(value, pcie->base + MVPCIE_CONF_DATA_OFF + (offset & 3));
break;
case PCI_SIZE_16:
writew(value, pcie->base + MVPCIE_CONF_DATA_OFF + (offset & 2));
break;
case PCI_SIZE_32:
writel(value, pcie->base + MVPCIE_CONF_DATA_OFF);
break;
default:
return -EINVAL;
}
return 0;
}
/*
* Setup PCIE BARs and Address Decode Wins:
* BAR[0] -> internal registers
* BAR[1] -> covers all DRAM banks
* BAR[2] -> disabled
* WIN[0-3] -> DRAM bank[0-3]
*/
static void mvebu_pcie_setup_wins(struct mvebu_pcie *pcie)
{
const struct mbus_dram_target_info *dram = mvebu_mbus_dram_info();
u32 size;
int i;
/* First, disable and clear BARs and windows. */
for (i = 1; i < 3; i++) {
writel(0, pcie->base + MVPCIE_BAR_CTRL_OFF(i));
writel(0, pcie->base + MVPCIE_BAR_LO_OFF(i));
writel(0, pcie->base + MVPCIE_BAR_HI_OFF(i));
}
for (i = 0; i < 5; i++) {
writel(0, pcie->base + MVPCIE_WIN04_CTRL_OFF(i));
writel(0, pcie->base + MVPCIE_WIN04_BASE_OFF(i));
writel(0, pcie->base + MVPCIE_WIN04_REMAP_OFF(i));
}
writel(0, pcie->base + MVPCIE_WIN5_CTRL_OFF);
writel(0, pcie->base + MVPCIE_WIN5_BASE_OFF);
writel(0, pcie->base + MVPCIE_WIN5_REMAP_OFF);
/* Setup windows for DDR banks. Count total DDR size on the fly. */
size = 0;
for (i = 0; i < dram->num_cs; i++) {
const struct mbus_dram_window *cs = dram->cs + i;
writel(cs->base & 0xffff0000,
pcie->base + MVPCIE_WIN04_BASE_OFF(i));
writel(0, pcie->base + MVPCIE_WIN04_REMAP_OFF(i));
writel(((cs->size - 1) & 0xffff0000) |
(cs->mbus_attr << 8) |
(dram->mbus_dram_target_id << 4) | 1,
pcie->base + MVPCIE_WIN04_CTRL_OFF(i));
size += cs->size;
}
/* Round up 'size' to the nearest power of two. */
if ((size & (size - 1)) != 0)
size = 1 << fls(size);
/* Setup BAR[1] to all DRAM banks. */
writel(dram->cs[0].base | 0xc, pcie->base + MVPCIE_BAR_LO_OFF(1));
writel(0, pcie->base + MVPCIE_BAR_HI_OFF(1));
writel(((size - 1) & 0xffff0000) | 0x1,
pcie->base + MVPCIE_BAR_CTRL_OFF(1));
/* Setup BAR[0] to internal registers. */
writel(pcie->intregs, pcie->base + MVPCIE_BAR_LO_OFF(0));
writel(0, pcie->base + MVPCIE_BAR_HI_OFF(0));
}
/* Only enable PCIe link, do not setup it */
static int mvebu_pcie_enable_link(struct mvebu_pcie *pcie, ofnode node)
{
struct reset_ctl rst;
int ret;
ret = reset_get_by_index_nodev(node, 0, &rst);
if (ret == -ENOENT) {
return 0;
} else if (ret < 0) {
printf("%s: cannot get reset controller: %d\n", pcie->name, ret);
return ret;
}
ret = reset_request(&rst);
if (ret) {
printf("%s: cannot request reset controller: %d\n", pcie->name, ret);
return ret;
}
ret = reset_deassert(&rst);
reset_free(&rst);
if (ret) {
printf("%s: cannot enable PCIe port: %d\n", pcie->name, ret);
return ret;
}
return 0;
}
/* Setup PCIe link but do not enable it */
static void mvebu_pcie_setup_link(struct mvebu_pcie *pcie)
{
u32 reg;
/* Setup PCIe controller to Root Complex mode */
reg = readl(pcie->base + MVPCIE_CTRL_OFF);
reg |= MVPCIE_CTRL_RC_MODE;
writel(reg, pcie->base + MVPCIE_CTRL_OFF);
/*
* Set Maximum Link Width to X1 or X4 in Root Port's PCIe Link
* Capability register. This register is defined by PCIe specification
* as read-only but this mvebu controller has it as read-write and must
* be set to number of SerDes PCIe lanes (1 or 4). If this register is
* not set correctly then link with endpoint card is not established.
*/
reg = readl(pcie->base + MVPCIE_ROOT_PORT_PCI_EXP_OFF + PCI_EXP_LNKCAP);
reg &= ~PCI_EXP_LNKCAP_MLW;
reg |= (pcie->is_x4 ? 4 : 1) << 4;
writel(reg, pcie->base + MVPCIE_ROOT_PORT_PCI_EXP_OFF + PCI_EXP_LNKCAP);
}
static int mvebu_pcie_probe(struct udevice *dev)
{
struct mvebu_pcie *pcie = dev_get_plat(dev);
struct udevice *ctlr = pci_get_controller(dev);
struct pci_controller *hose = dev_get_uclass_priv(ctlr);
u32 reg;
/*
* Change Class Code of PCI Bridge device to PCI Bridge (0x600400)
* because default value is Memory controller (0x508000) which
* U-Boot cannot recognize as P2P Bridge.
*
* Note that this mvebu PCI Bridge does not have compliant Type 1
* Configuration Space. Header Type is reported as Type 0 and it
* has format of Type 0 config space.
*
* Moreover Type 0 BAR registers (ranges 0x10 - 0x28 and 0x30 - 0x34)
* have the same format in Marvell's specification as in PCIe
* specification, but their meaning is totally different and they do
* different things: they are aliased into internal mvebu registers
* (e.g. MVPCIE_BAR_LO_OFF) and these should not be changed or
* reconfigured by pci device drivers.
*
* So our driver converts Type 0 config space to Type 1 and reports
* Header Type as Type 1. Access to BAR registers and to non-existent
* Type 1 registers is redirected to the virtual cfgcache[] buffer,
* which avoids changing unrelated registers.
*/
reg = readl(pcie->base + MVPCIE_ROOT_PORT_PCI_CFG_OFF + PCI_CLASS_REVISION);
reg &= ~0xffffff00;
reg |= (PCI_CLASS_BRIDGE_PCI << 8) << 8;
writel(reg, pcie->base + MVPCIE_ROOT_PORT_PCI_CFG_OFF + PCI_CLASS_REVISION);
/*
* mvebu uses local bus number and local device number to determinate
* type of config request. Type 0 is used if target bus number equals
* local bus number and target device number differs from local device
* number. Type 1 is used if target bus number differs from local bus
* number. And when target bus number equals local bus number and
* target device equals local device number then request is routed to
* PCI Bridge which represent local PCIe Root Port.
*
* It means that PCI root and secondary buses shares one bus number
* which is configured via local bus number. Determination if config
* request should go to root or secondary bus is done based on local
* device number.
*
* PCIe is point-to-point bus, so at secondary bus is always exactly one
* device with number 0. So set local device number to 1, it would not
* conflict with any device on secondary bus number and will ensure that
* accessing secondary bus and all buses behind secondary would work
* automatically and correctly. Therefore this configuration of local
* device number implies that setting of local bus number configures
* secondary bus number. Set it to 0 as U-Boot CONFIG_PCI_PNP code will
* later configure it via config write requests to the correct value.
* mvebu_pcie_write_config() catches config write requests which tries
* to change secondary bus number and correctly updates local bus number
* based on new secondary bus number.
*
* With this configuration is PCI Bridge available at secondary bus as
* device number 1. But it must be available at root bus (zero) as device
* number 0. So in mvebu_pcie_read_config() and mvebu_pcie_write_config()
* functions rewrite address to the real one when accessing the root bus.
*/
mvebu_pcie_set_local_bus_nr(pcie, 0);
mvebu_pcie_set_local_dev_nr(pcie, 1);
/*
* Kirkwood arch code already maps mbus windows for PCIe IO and MEM.
* So skip calling mvebu_mbus_add_window_by_id() function as it would
* fail on error "conflicts with another window" which means conflict
* with existing PCIe window mappings.
*/
#ifndef CONFIG_ARCH_KIRKWOOD
if (resource_size(&pcie->mem) &&
mvebu_mbus_add_window_by_id(pcie->mem_target, pcie->mem_attr,
(phys_addr_t)pcie->mem.start,
resource_size(&pcie->mem))) {
printf("%s: unable to add mbus window for mem at %08x+%08x\n",
pcie->name,
(u32)pcie->mem.start, (unsigned)resource_size(&pcie->mem));
pcie->mem.start = 0;
pcie->mem.end = -1;
}
if (resource_size(&pcie->io) &&
mvebu_mbus_add_window_by_id(pcie->io_target, pcie->io_attr,
(phys_addr_t)pcie->io.start,
resource_size(&pcie->io))) {
printf("%s: unable to add mbus window for IO at %08x+%08x\n",
pcie->name,
(u32)pcie->io.start, (unsigned)resource_size(&pcie->io));
pcie->io.start = 0;
pcie->io.end = -1;
}
#endif
/* Setup windows and configure host bridge */
mvebu_pcie_setup_wins(pcie);
/* PCI memory space */
pci_set_region(hose->regions + 0, pcie->mem.start,
pcie->mem.start, resource_size(&pcie->mem), PCI_REGION_MEM);
hose->region_count = 1;
if (resource_size(&pcie->mem)) {
pci_set_region(hose->regions + hose->region_count,
pcie->mem.start, pcie->mem.start,
resource_size(&pcie->mem),
PCI_REGION_MEM);
hose->region_count++;
}
if (resource_size(&pcie->io)) {
pci_set_region(hose->regions + hose->region_count,
pcie->io.start, pcie->io.start,
resource_size(&pcie->io),
PCI_REGION_IO);
hose->region_count++;
}
/* PCI Bridge support 32-bit I/O and 64-bit prefetch mem addressing */
pcie->cfgcache[(PCI_IO_BASE - 0x10) / 4] =
PCI_IO_RANGE_TYPE_32 | (PCI_IO_RANGE_TYPE_32 << 8);
pcie->cfgcache[(PCI_PREF_MEMORY_BASE - 0x10) / 4] =
PCI_PREF_RANGE_TYPE_64 | (PCI_PREF_RANGE_TYPE_64 << 16);
mvebu_pcie_wait_for_link(pcie);
return 0;
}
#define DT_FLAGS_TO_TYPE(flags) (((flags) >> 24) & 0x03)
#define DT_TYPE_IO 0x1
#define DT_TYPE_MEM32 0x2
#define DT_CPUADDR_TO_TARGET(cpuaddr) (((cpuaddr) >> 56) & 0xFF)
#define DT_CPUADDR_TO_ATTR(cpuaddr) (((cpuaddr) >> 48) & 0xFF)
static int mvebu_get_tgt_attr(ofnode node, int devfn,
unsigned long type,
unsigned int *tgt,
unsigned int *attr)
{
const int na = 3, ns = 2;
const __be32 *range;
int rlen, nranges, rangesz, pna, i;
*tgt = -1;
*attr = -1;
range = ofnode_get_property(node, "ranges", &rlen);
if (!range)
return -EINVAL;
/*
* Linux uses of_n_addr_cells() to get the number of address cells
* here. Currently this function is only available in U-Boot when
* CONFIG_OF_LIVE is enabled. Until this is enabled for MVEBU in
* general, lets't hardcode the "pna" value in the U-Boot code.
*/
pna = 2; /* hardcoded for now because of lack of of_n_addr_cells() */
rangesz = pna + na + ns;
nranges = rlen / sizeof(__be32) / rangesz;
for (i = 0; i < nranges; i++, range += rangesz) {
u32 flags = of_read_number(range, 1);
u32 slot = of_read_number(range + 1, 1);
u64 cpuaddr = of_read_number(range + na, pna);
unsigned long rtype;
if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_IO)
rtype = IORESOURCE_IO;
else if (DT_FLAGS_TO_TYPE(flags) == DT_TYPE_MEM32)
rtype = IORESOURCE_MEM;
else
continue;
/*
* The Linux code used PCI_SLOT() here, which expects devfn
* in bits 7..0. PCI_DEV() in U-Boot is similar to PCI_SLOT(),
* only expects devfn in 15..8, where its saved in this driver.
*/
if (slot == PCI_DEV(devfn) && type == rtype) {
*tgt = DT_CPUADDR_TO_TARGET(cpuaddr);
*attr = DT_CPUADDR_TO_ATTR(cpuaddr);
return 0;
}
}
return -ENOENT;
}
static int mvebu_pcie_port_parse_dt(ofnode node, ofnode parent, struct mvebu_pcie *pcie)
{
struct fdt_pci_addr pci_addr;
const u32 *addr;
u32 num_lanes;
int ret = 0;
int len;
/* Get port number, lane number and memory target / attr */
if (ofnode_read_u32(node, "marvell,pcie-port",
&pcie->port)) {
ret = -ENODEV;
goto err;
}
if (ofnode_read_u32(node, "marvell,pcie-lane", &pcie->lane))
pcie->lane = 0;
sprintf(pcie->name, "pcie%d.%d", pcie->port, pcie->lane);
if (!ofnode_read_u32(node, "num-lanes", &num_lanes) && num_lanes == 4)
pcie->is_x4 = true;
/* devfn is in bits [15:8], see PCI_DEV usage */
ret = ofnode_read_pci_addr(node, FDT_PCI_SPACE_CONFIG, "reg", &pci_addr);
if (ret < 0) {
printf("%s: property \"reg\" is invalid\n", pcie->name);
goto err;
}
pcie->devfn = pci_addr.phys_hi & 0xff00;
ret = mvebu_get_tgt_attr(parent, pcie->devfn,
IORESOURCE_MEM,
&pcie->mem_target, &pcie->mem_attr);
if (ret < 0) {
printf("%s: cannot get tgt/attr for mem window\n", pcie->name);
goto err;
}
ret = mvebu_get_tgt_attr(parent, pcie->devfn,
IORESOURCE_IO,
&pcie->io_target, &pcie->io_attr);
if (ret < 0) {
printf("%s: cannot get tgt/attr for IO window\n", pcie->name);
goto err;
}
/* Parse PCIe controller register base from DT */
addr = ofnode_get_property(node, "assigned-addresses", &len);
if (!addr) {
printf("%s: property \"assigned-addresses\" not found\n", pcie->name);
ret = -FDT_ERR_NOTFOUND;
goto err;
}
pcie->base = (void *)(u32)ofnode_translate_address(node, addr);
pcie->intregs = (u32)pcie->base - fdt32_to_cpu(addr[2]);
return 0;
err:
return ret;
}
static const struct dm_pci_ops mvebu_pcie_ops = {
.read_config = mvebu_pcie_read_config,
.write_config = mvebu_pcie_write_config,
};
static struct driver pcie_mvebu_drv = {
.name = "pcie_mvebu",
.id = UCLASS_PCI,
.ops = &mvebu_pcie_ops,
.probe = mvebu_pcie_probe,
.plat_auto = sizeof(struct mvebu_pcie),
};
/*
* Use a MISC device to bind the n instances (child nodes) of the
* PCIe base controller in UCLASS_PCI.
*/
static int mvebu_pcie_bind(struct udevice *parent)
{
struct mvebu_pcie **ports_pcie;
struct mvebu_pcie *pcie;
struct uclass_driver *drv;
struct udevice *dev;
struct resource mem;
struct resource io;
int ports_count, i;
ofnode *ports_nodes;
ofnode subnode;
/* Lookup pci driver */
drv = lists_uclass_lookup(UCLASS_PCI);
if (!drv) {
puts("Cannot find PCI driver\n");
return -ENOENT;
}
ports_count = ofnode_get_child_count(dev_ofnode(parent));
ports_pcie = calloc(ports_count, sizeof(*ports_pcie));
ports_nodes = calloc(ports_count, sizeof(*ports_nodes));
if (!ports_pcie || !ports_nodes) {
free(ports_pcie);
free(ports_nodes);
return -ENOMEM;
}
ports_count = 0;
#ifdef CONFIG_ARCH_KIRKWOOD
mem.start = KW_DEFADR_PCI_MEM;
mem.end = KW_DEFADR_PCI_MEM + KW_DEFADR_PCI_MEM_SIZE - 1;
io.start = KW_DEFADR_PCI_IO;
io.end = KW_DEFADR_PCI_IO + KW_DEFADR_PCI_IO_SIZE - 1;
#else
mem.start = MBUS_PCI_MEM_BASE;
mem.end = MBUS_PCI_MEM_BASE + MBUS_PCI_MEM_SIZE - 1;
io.start = MBUS_PCI_IO_BASE;
io.end = MBUS_PCI_IO_BASE + MBUS_PCI_IO_SIZE - 1;
#endif
/* First phase: Fill mvebu_pcie struct for each port */
ofnode_for_each_subnode(subnode, dev_ofnode(parent)) {
if (!ofnode_is_available(subnode))
continue;
pcie = calloc(1, sizeof(*pcie));
if (!pcie)
continue;
if (mvebu_pcie_port_parse_dt(subnode, dev_ofnode(parent), pcie) < 0) {
free(pcie);
continue;
}
/*
* MVEBU PCIe controller needs MEMORY and I/O BARs to be mapped
* into SoCs address space. Each controller will map 128M of MEM
* and 64K of I/O space when registered.
*/
if (resource_size(&mem) >= SZ_128M) {
pcie->mem.start = mem.start;
pcie->mem.end = mem.start + SZ_128M - 1;
mem.start += SZ_128M;
} else {
printf("%s: unable to assign mbus window for mem\n", pcie->name);
pcie->mem.start = 0;
pcie->mem.end = -1;
}
if (resource_size(&io) >= SZ_64K) {
pcie->io.start = io.start;
pcie->io.end = io.start + SZ_64K - 1;
io.start += SZ_64K;
} else {
printf("%s: unable to assign mbus window for io\n", pcie->name);
pcie->io.start = 0;
pcie->io.end = -1;
}
ports_pcie[ports_count] = pcie;
ports_nodes[ports_count] = subnode;
ports_count++;
}
/* Second phase: Setup all PCIe links (do not enable them yet) */
for (i = 0; i < ports_count; i++)
mvebu_pcie_setup_link(ports_pcie[i]);
/* Third phase: Enable all PCIe links and create for each UCLASS_PCI device */
for (i = 0; i < ports_count; i++) {
pcie = ports_pcie[i];
subnode = ports_nodes[i];
/*
* PCIe link can be enabled only after all PCIe links were
* properly configured. This is because more PCIe links shares
* one enable bit and some PCIe links cannot be enabled
* individually.
*/
if (mvebu_pcie_enable_link(pcie, subnode) < 0) {
free(pcie);
continue;
}
/* Create child device UCLASS_PCI and bind it */
device_bind(parent, &pcie_mvebu_drv, pcie->name, pcie, subnode,
&dev);
}
free(ports_pcie);
free(ports_nodes);
return 0;
}
static const struct udevice_id mvebu_pcie_ids[] = {
{ .compatible = "marvell,armada-xp-pcie" },
{ .compatible = "marvell,armada-370-pcie" },
{ .compatible = "marvell,kirkwood-pcie" },
{ }
};
U_BOOT_DRIVER(pcie_mvebu_base) = {
.name = "pcie_mvebu_base",
.id = UCLASS_MISC,
.of_match = mvebu_pcie_ids,
.bind = mvebu_pcie_bind,
};