blob: 3c4ba095e4e71bbcc9d6e85e94c33a58602a203a [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
*
* Configuration settings for the SolidRun mx6 based boards
*/
#ifndef __MX6CUBOXI_CONFIG_H
#define __MX6CUBOXI_CONFIG_H
#include <linux/stringify.h>
#include "mx6_common.h"
/* MMC Configs */
#define CFG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
/* Framebuffer */
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
/* USB */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/* Command definition */
#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_EXTRA_ENV_SETTINGS \
"som_rev=undefined\0" \
"has_emmc=undefined\0" \
"fdtfile=undefined\0" \
"fdt_addr_r=0x18000000\0" \
"fdt_addr=0x18000000\0" \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"pxefile_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"scriptaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"ramdisk_addr_r=0x13000000\0" \
"ramdiskaddr=0x13000000\0" \
"initrd_high=0xffffffff\0" \
"ip_dyn=yes\0" \
"console=ttymxc0\0" \
"bootm_size=0x10000000\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"finduuid=part uuid mmc 1:1 uuid\0" \
"update_sd_firmware=" \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if mmc dev ${mmcdev}; then " \
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
"findfdt="\
"if test ${board_rev} = MX6Q; then " \
"setenv fdtprefix imx6q; fi; " \
"if test ${board_rev} = MX6DL; then " \
"setenv fdtprefix imx6dl; fi; " \
"if test ${som_rev} = V15; then " \
"setenv fdtsuffix -som-v15; fi; " \
"if test ${has_emmc} = yes; then " \
"setenv emmcsuffix -emmc; fi; " \
"if test ${board_name} = HUMMINGBOARD2 ; then " \
"setenv fdtfile ${fdtprefix}-hummingboard2${emmcsuffix}${fdtsuffix}.dtb; fi; " \
"if test ${board_name} = HUMMINGBOARD ; then " \
"setenv fdtfile ${fdtprefix}-hummingboard${emmcsuffix}${fdtsuffix}.dtb; fi; " \
"if test ${board_name} = CUBOXI ; then " \
"setenv fdtfile ${fdtprefix}-cubox-i${emmcsuffix}${fdtsuffix}.dtb; fi; " \
"if test ${fdtfile} = undefined; then " \
"echo WARNING: Could not determine dtb to use; fi; \0" \
BOOTENV
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 2) \
func(SATA, sata, 0) \
func(USB, usb, 0) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
/* Physical Memory Map */
#define CFG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
/* Environment organization */
#endif /* __MX6CUBOXI_CONFIG_H */