| menu "Power" |
| |
| source "drivers/power/domain/Kconfig" |
| |
| source "drivers/power/pmic/Kconfig" |
| |
| source "drivers/power/regulator/Kconfig" |
| |
| choice |
| prompt "Select Sunxi PMIC Variant" |
| depends on ARCH_SUNXI |
| default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 |
| default AXP818_POWER if MACH_SUN8I_A83T |
| default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I |
| |
| config SUNXI_NO_PMIC |
| bool "board without a pmic" |
| ---help--- |
| Select this for boards which do not use a PMIC. |
| |
| config AXP152_POWER |
| bool "axp152 pmic support" |
| depends on MACH_SUN5I |
| select CMD_POWEROFF |
| ---help--- |
| Select this to enable support for the axp152 pmic found on most |
| A10s boards. |
| |
| config AXP209_POWER |
| bool "axp209 pmic support" |
| depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| select CMD_POWEROFF |
| ---help--- |
| Select this to enable support for the axp209 pmic found on most |
| A10, A13 and A20 boards. |
| |
| config AXP221_POWER |
| bool "axp221 / axp223 pmic support" |
| depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 |
| select CMD_POWEROFF |
| ---help--- |
| Select this to enable support for the axp221/axp223 pmic found on most |
| A23 and A31 boards. |
| |
| config AXP809_POWER |
| bool "axp809 pmic support" |
| depends on MACH_SUN9I |
| select CMD_POWEROFF |
| ---help--- |
| Say y here to enable support for the axp809 pmic found on A80 boards. |
| |
| config AXP818_POWER |
| bool "axp818 pmic support" |
| depends on MACH_SUN8I_A83T |
| select CMD_POWEROFF |
| ---help--- |
| Say y here to enable support for the axp818 pmic found on |
| A83T dev board. |
| |
| config SY8106A_POWER |
| bool "SY8106A pmic support" |
| depends on MACH_SUNXI_H3_H5 |
| ---help--- |
| Select this to enable support for the SY8106A pmic found on some |
| H3 boards. |
| |
| endchoice |
| |
| config AXP_DCDC1_VOLT |
| int "axp pmic dcdc1 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 3300 if AXP818_POWER || MACH_SUN8I_R40 |
| default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to |
| disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for |
| generic 3.3V IO voltage for external devices like the lcd-panal and |
| sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to |
| save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T |
| dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally |
| powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. |
| |
| config AXP_DCDC2_VOLT |
| int "axp pmic dcdc2 voltage" |
| depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 900 if AXP818_POWER |
| default 1400 if AXP152_POWER || AXP209_POWER |
| default 1200 if MACH_SUN6I |
| default 1100 if MACH_SUN8I |
| default 0 if MACH_SUN9I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to |
| disable dcdc2. |
| On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. |
| On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. |
| On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. |
| On A80 boards dcdc2 powers the GPU and can be left off. |
| On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. |
| On R40 boards dcdc2 is VDD-CPU and should be 1.1V |
| |
| config AXP_DCDC3_VOLT |
| int "axp pmic dcdc3 voltage" |
| depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 900 if AXP809_POWER || AXP818_POWER |
| default 1500 if AXP152_POWER |
| default 1250 if AXP209_POWER |
| default 1100 if MACH_SUN8I_R40 |
| default 1200 if MACH_SUN6I || MACH_SUN8I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to |
| disable dcdc3. |
| On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and |
| should be 1.25V. |
| On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. |
| On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. |
| On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. |
| On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. |
| On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. |
| |
| config AXP_DCDC4_VOLT |
| int "axp pmic dcdc4 voltage" |
| depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 1250 if AXP152_POWER |
| default 1200 if MACH_SUN6I |
| default 0 if MACH_SUN8I |
| default 900 if MACH_SUN9I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to |
| disable dcdc4. |
| On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. |
| On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. |
| On A23 / A33 boards dcdc4 is unused and should be disabled. |
| On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. |
| On A83T boards dcdc4 is used for VDD-GPU. |
| |
| config AXP_DCDC5_VOLT |
| int "axp pmic dcdc5 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to |
| disable dcdc5. |
| On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and |
| should be 1.5V, 1.35V if DDR3L is used. |
| |
| config AXP_ALDO1_VOLT |
| int "axp pmic (a)ldo1 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 0 if MACH_SUN6I || MACH_SUN8I_R40 |
| default 1800 if MACH_SUN8I_A83T |
| default 3000 if MACH_SUN8I || MACH_SUN9I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to |
| disable aldo1. |
| On A31 boards aldo1 is often used to power the wifi module. |
| On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. |
| On A80 boards aldo1 powers the USB hosts and should be 3.0V. |
| On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and |
| should be 1.8V. |
| |
| config AXP_ALDO2_VOLT |
| int "axp pmic (a)ldo2 voltage" |
| depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 3000 if AXP152_POWER || AXP209_POWER |
| default 0 if MACH_SUN6I || MACH_SUN9I |
| default 1800 if MACH_SUN8I_A83T |
| default 2500 if MACH_SUN8I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to |
| disable aldo2. |
| On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. |
| On A31 boards aldo2 is typically unused and should be disabled. |
| On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. |
| On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. |
| On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. |
| On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, |
| LPDDR2, and the codec. It should be 1.8V. |
| |
| config AXP_ALDO3_VOLT |
| int "axp pmic (a)ldo3 voltage" |
| depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 0 if AXP209_POWER || MACH_SUN9I |
| default 3000 if MACH_SUN6I || MACH_SUN8I |
| ---help--- |
| Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to |
| disable aldo3. |
| On A10(s) / A13 / A20 boards aldo3 should be 2.8V. |
| On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should |
| be 3.0V. |
| On A80 boards aldo3 is normally not used. |
| On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be |
| 3.0V. |
| |
| config AXP_ALDO4_VOLT |
| int "axp pmic (a)ldo4 voltage" |
| depends on AXP209_POWER |
| default 0 if AXP209_POWER |
| ---help--- |
| Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to |
| disable aldo4. |
| On A10(s) / A13 / A20 boards aldo4 should be 2.8V. |
| |
| config AXP_DLDO1_VOLT |
| int "axp pmic dldo1 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to |
| disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used |
| to power the ethernet phy. On A23, A33 and A80 boards this is often |
| used to power the wifi. |
| |
| config AXP_DLDO2_VOLT |
| int "axp pmic dldo2 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 3000 if MACH_SUN9I |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to |
| disable dldo2. |
| On A80 boards dldo2 normally powers the PL pins and should be 3.0V. |
| |
| config AXP_DLDO3_VOLT |
| int "axp pmic dldo3 voltage" |
| depends on AXP221_POWER || AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to |
| disable dldo3. |
| |
| config AXP_DLDO4_VOLT |
| int "axp pmic dldo4 voltage" |
| depends on AXP221_POWER || AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to |
| disable dldo4. |
| |
| config AXP_ELDO1_VOLT |
| int "axp pmic eldo1 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to |
| disable eldo1. |
| |
| config AXP_ELDO2_VOLT |
| int "axp pmic eldo2 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to |
| disable eldo2. |
| |
| config AXP_ELDO3_VOLT |
| int "axp pmic eldo3 voltage" |
| depends on AXP221_POWER || AXP809_POWER || AXP818_POWER |
| default 3000 if MACH_SUN9I |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to |
| disable eldo3. On some A31(s) tablets it might be used to supply |
| 1.2V for the SSD2828 chip (converter of parallel LCD interface |
| into MIPI DSI). |
| On A80 boards it powers the PM pingroup and should be 3.0V. |
| |
| config AXP_FLDO1_VOLT |
| int "axp pmic fldo1 voltage" |
| depends on AXP818_POWER |
| default 0 if MACH_SUN8I_A83T |
| ---help--- |
| Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to |
| disable fldo1. |
| On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is |
| used. |
| |
| config AXP_FLDO2_VOLT |
| int "axp pmic fldo2 voltage" |
| depends on AXP818_POWER |
| default 900 if MACH_SUN8I_A83T |
| ---help--- |
| Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to |
| disable fldo2. |
| On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V. |
| |
| config AXP_FLDO3_VOLT |
| int "axp pmic fldo3 voltage" |
| depends on AXP818_POWER |
| default 0 |
| ---help--- |
| Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to |
| disable fldo3. |
| |
| config AXP_SW_ON |
| bool "axp pmic sw on" |
| depends on AXP809_POWER || AXP818_POWER |
| default n |
| ---help--- |
| Enable to turn on axp pmic sw. |
| |
| config SY8106A_VOUT1_VOLT |
| int "SY8106A pmic VOUT1 voltage" |
| depends on SY8106A_POWER |
| default 1200 |
| ---help--- |
| Set the voltage (mV) to program the SY8106A pmic VOUT1. This |
| is typically used to power the VDD-CPU and should be 1200mV. |
| Values can range from 680mV till 1950mV. |
| |
| endmenu |