include/configs/ls1043a_common.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2015 Freescale Semiconductor
  */

 #ifndef __LS1043A_COMMON_H
 #define __LS1043A_COMMON_H

 /* SPL build */
 #ifdef CONFIG_SPL_BUILD
 #define SPL_NO_FMAN
 #define SPL_NO_DSPI
 #define SPL_NO_PCIE
 #define SPL_NO_ENV
 #define SPL_NO_MISC
 #define SPL_NO_USB
 #define SPL_NO_SATA
 #define SPL_NO_QE
 #define SPL_NO_EEPROM
 #endif
 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
 #define SPL_NO_MMC
 #endif
 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
 #define SPL_NO_IFC
 #endif

 #define CONFIG_REMAKE_ELF
 #define CONFIG_FSL_LAYERSCAPE
 #define CONFIG_GICV2

 #include <asm/arch/stream_id_lsch2.h>
 #include <asm/arch/config.h>

 /* Link Definitions */
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

 #define CONFIG_SKIP_LOWLEVEL_INIT

 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL

 #define CPU_RELEASE_ADDR               secondary_boot_func

 /* Generic Timer Definitions */
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)

 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /* SD boot SPL */
 #ifdef CONFIG_SD_BOOT

 #define CONFIG_SPL_TEXT_BASE		0x10000000
 #define CONFIG_SPL_MAX_SIZE		0x17000
 #define CONFIG_SPL_STACK		0x1001e000
 #define CONFIG_SPL_PAD_TO		0x1d000

 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
 					CONFIG_SPL_BSS_MAX_SIZE)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #ifdef CONFIG_SECURE_BOOT
 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw u-boot image instead of fit image.
  */
 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif /* ifdef CONFIG_SECURE_BOOT */
 #endif

 /* NAND SPL */
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SPL_PBL_PAD
 #define CONFIG_SPL_TEXT_BASE		0x10000000
 #define CONFIG_SPL_MAX_SIZE		0x1a000
 #define CONFIG_SPL_STACK		0x1001d000
 #define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #ifdef CONFIG_SECURE_BOOT
 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
 #endif /* ifdef CONFIG_SECURE_BOOT */

 #ifdef CONFIG_U_BOOT_HDR_SIZE
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw u-boot image instead of fit image.
  */
 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */

 #endif

 /* IFC */
 #ifndef SPL_NO_IFC
 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_FSL_IFC
 /*
  * CONFIG_SYS_FLASH_BASE has the final address (core view)
  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
  */
 #define CONFIG_SYS_FLASH_BASE			0x60000000
 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000

 #ifdef CONFIG_MTD_NOR_FLASH
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
 #endif
 #endif
 #endif

 /* I2C */
 #define CONFIG_SYS_I2C

 /* PCIe */
 #ifndef SPL_NO_PCIE
 #define CONFIG_PCIE1		/* PCIE controller 1 */
 #define CONFIG_PCIE2		/* PCIE controller 2 */
 #define CONFIG_PCIE3		/* PCIE controller 3 */

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 #endif

 /* Command line configuration */

 /*  MMC  */
 #ifndef SPL_NO_MMC
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 #endif
 #endif

 /*  DSPI  */
 #ifndef SPL_NO_DSPI
 #define CONFIG_FSL_DSPI
 #ifdef CONFIG_FSL_DSPI
 #define CONFIG_DM_SPI_FLASH
 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
 #define CONFIG_SPI_FLASH_SST		/* cs1 */
 #define CONFIG_SPI_FLASH_EON		/* cs2 */
 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_SF_DEFAULT_BUS		1
 #define CONFIG_SF_DEFAULT_CS		0
 #endif
 #endif
 #endif

 /* FMan ucode */
 #ifndef SPL_NO_FMAN
 #define CONFIG_SYS_DPAA_FMAN
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_FM_MURAM_SIZE	0x60000

 #ifdef CONFIG_NAND_BOOT
 /* Store Fman ucode at offeset 0x900000(72 blocks). */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #define CONFIG_SYS_FMAN_FW_ADDR		(72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SD_BOOT)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
  * about 1MB (2040 blocks), Env is stored after the image, and the env size is
  * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 #define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
 #define CONFIG_SYS_QE_FW_ADDR		(512 * 0x4a08)
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 #define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
 #define CONFIG_ENV_SPI_BUS		0
 #define CONFIG_ENV_SPI_CS		0
 #define CONFIG_ENV_SPI_MAX_HZ		1000000
 #define CONFIG_ENV_SPI_MODE		0x03
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 /* FMan fireware Pre-load address */
 #define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
 #define CONFIG_SYS_QE_FW_ADDR		0x60940000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif
 #endif

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128

 #ifndef SPL_NO_MISC
 #ifndef CONFIG_SPL_BUILD
 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0)
 #include <config_distro_bootcmd.h>
 #endif

 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"fdt_high=0xffffffffffffffff\0"		\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"fdt_addr=0x64f00000\0"		 	\
 	"kernel_addr=0x61000000\0"		\
 	"scriptaddr=0x80000000\0"		\
 	"scripthdraddr=0x80080000\0"		\
 	"fdtheader_addr_r=0x80100000\0"		\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"		\
 	"fdt_addr_r=0x90000000\0"		\
 	"load_addr=0xa0000000\0"		\
 	"kernelheader_addr=0x60800000\0"	\
 	"kernel_size=0x2800000\0"		\
 	"kernelheader_size=0x40000\0"		\
 	"kernel_addr_sd=0x8000\0"		\
 	"kernel_size_sd=0x14000\0"		\
 	"kernelhdr_addr_sd=0x4000\0"		\
 	"kernelhdr_size_sd=0x10\0"		\
 	"console=ttyS0,115200\0"		\
 	"boot_os=y\0"				\
 	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"	\
 	BOOTENV					\
 	"boot_scripts=ls1043ardb_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1043ardb_bs.out\0"	\
 	"scan_dev_for_boot_part="		\
 		"part list ${devtype} ${devnum} devplist; "	\
 		"env exists devplist || setenv devplist 1; "	\
 		"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "			\
 				"${devnum}:${distro_bootpart} "	\
 				"bootfstype; then "		\
 				"run scan_dev_for_boot; "	\
 			"fi; "					\
 		"done\0"			\
 	"scan_dev_for_boot="					\
 		"echo Scanning ${devtype} "			\
 			"${devnum}:${distro_bootpart}...; "	\
 		"for prefix in ${boot_prefixes}; do "		\
 			"run scan_dev_for_scripts; "		\
 		"done;\0"					\
 	"boot_a_script="					\
 		"load ${devtype} ${devnum}:${distro_bootpart} "	\
 			"${scriptaddr} ${prefix}${script}; "	\
 		"env exists secureboot && load ${devtype} "	\
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} "	\
 			"&& esbc_validate ${scripthdraddr};"	\
 		"source ${scriptaddr}\0"			\
 	"qspi_bootcmd=echo Trying load from qspi..;"	\
 		"sf probe && sf read $load_addr "	\
 		"$kernel_addr $kernel_size; env exists secureboot "	\
 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"	\
 	"nor_bootcmd=echo Trying load from nor..;"	\
 		"cp.b $kernel_addr $load_addr "	\
 		"$kernel_size; env exists secureboot "	\
 		"&& cp.b $kernelheader_addr $kernelheader_addr_r "	\
 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 		"bootm $load_addr#$board\0"	    \
 	"sd_bootcmd=echo Trying load from SD ..;"       \
 		"mmcinfo; mmc read $load_addr "         \
 		"$kernel_addr_sd $kernel_size_sd && "     \
 		"env exists secureboot && mmc read $kernelheader_addr_r "		\
 		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
 		" && esbc_validate ${kernelheader_addr_r};"	\
 		"bootm $load_addr#$board\0"


 #undef CONFIG_BOOTCOMMAND
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "	\
 			   "env exists secureboot && esbc_halt;"
 #elif defined(CONFIG_SD_BOOT)
 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; "  \
 			   "env exists secureboot && esbc_halt;"
 #else
 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; "	\
 			   "env exists secureboot && esbc_halt;"
 #endif
 #endif

 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */

 #define CONFIG_SYS_MAXARGS		64	/* max command args */

 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

 #include <asm/arch/soc.h>

 #endif /* __LS1043A_COMMON_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright (C) 2015 Freescale Semiconductor
	*/

	#ifndef __LS1043A_COMMON_H
	#define __LS1043A_COMMON_H

	/* SPL build */
	#ifdef CONFIG_SPL_BUILD
	#define SPL_NO_FMAN
	#define SPL_NO_DSPI
	#define SPL_NO_PCIE
	#define SPL_NO_ENV
	#define SPL_NO_MISC
	#define SPL_NO_USB
	#define SPL_NO_SATA
	#define SPL_NO_QE
	#define SPL_NO_EEPROM
	#endif
	#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
	#define SPL_NO_MMC
	#endif
	#if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
	#define SPL_NO_IFC
	#endif

	#define CONFIG_REMAKE_ELF
	#define CONFIG_FSL_LAYERSCAPE
	#define CONFIG_GICV2

	#include <asm/arch/stream_id_lsch2.h>
	#include <asm/arch/config.h>

	/* Link Definitions */
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

	#define CONFIG_SKIP_LOWLEVEL_INIT

	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL

	#define CPU_RELEASE_ADDR secondary_boot_func

	/* Generic Timer Definitions */
	#define COUNTER_FREQUENCY 25000000 /* 25MHz */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)

	/* Serial Port */
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_serial_clock())

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/* SD boot SPL */
	#ifdef CONFIG_SD_BOOT

	#define CONFIG_SPL_TEXT_BASE 0x10000000
	#define CONFIG_SPL_MAX_SIZE 0x17000
	#define CONFIG_SPL_STACK 0x1001e000
	#define CONFIG_SPL_PAD_TO 0x1d000

	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
	CONFIG_SPL_BSS_MAX_SIZE)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#ifdef CONFIG_SECURE_BOOT
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw u-boot image instead of fit image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_SECURE_BOOT */
	#endif

	/* NAND SPL */
	#ifdef CONFIG_NAND_BOOT
	#define CONFIG_SPL_PBL_PAD
	#define CONFIG_SPL_TEXT_BASE 0x10000000
	#define CONFIG_SPL_MAX_SIZE 0x1a000
	#define CONFIG_SPL_STACK 0x1001d000
	#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#ifdef CONFIG_SECURE_BOOT
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	#endif /* ifdef CONFIG_SECURE_BOOT */

	#ifdef CONFIG_U_BOOT_HDR_SIZE
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw u-boot image instead of fit image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */

	#endif

	/* IFC */
	#ifndef SPL_NO_IFC
	#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_FSL_IFC
	/*
	* CONFIG_SYS_FLASH_BASE has the final address (core view)
	* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
	* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
	* CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
	*/
	#define CONFIG_SYS_FLASH_BASE 0x60000000
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000

	#ifdef CONFIG_MTD_NOR_FLASH
	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
	#endif
	#endif
	#endif

	/* I2C */
	#define CONFIG_SYS_I2C

	/* PCIe */
	#ifndef SPL_NO_PCIE
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */
	#define CONFIG_PCIE3 /* PCIE controller 3 */

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_SCAN_SHOW
	#endif
	#endif

	/* Command line configuration */

	/* MMC */
	#ifndef SPL_NO_MMC
	#ifdef CONFIG_MMC
	#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
	#endif
	#endif

	/* DSPI */
	#ifndef SPL_NO_DSPI
	#define CONFIG_FSL_DSPI
	#ifdef CONFIG_FSL_DSPI
	#define CONFIG_DM_SPI_FLASH
	#define CONFIG_SPI_FLASH_STMICRO /* cs0 */
	#define CONFIG_SPI_FLASH_SST /* cs1 */
	#define CONFIG_SPI_FLASH_EON /* cs2 */
	#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_SF_DEFAULT_BUS 1
	#define CONFIG_SF_DEFAULT_CS 0
	#endif
	#endif
	#endif

	/* FMan ucode */
	#ifndef SPL_NO_FMAN
	#define CONFIG_SYS_DPAA_FMAN
	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_SYS_FM_MURAM_SIZE 0x60000

	#ifdef CONFIG_NAND_BOOT
	/* Store Fman ucode at offeset 0x900000(72 blocks). */
	#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
	#define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
	#elif defined(CONFIG_SD_BOOT)
	/*
	* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
	* about 1MB (2040 blocks), Env is stored after the image, and the env size is
	* 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
	*/
	#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
	#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
	#define CONFIG_SYS_QE_FW_ADDR (512 * 0x4a08)
	#elif defined(CONFIG_QSPI_BOOT)
	#define CONFIG_SYS_QE_FW_IN_SPIFLASH
	#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
	#define CONFIG_ENV_SPI_BUS 0
	#define CONFIG_ENV_SPI_CS 0
	#define CONFIG_ENV_SPI_MAX_HZ 1000000
	#define CONFIG_ENV_SPI_MODE 0x03
	#else
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	/* FMan fireware Pre-load address */
	#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
	#define CONFIG_SYS_QE_FW_ADDR 0x60940000
	#endif
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
	#endif
	#endif

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 128

	#ifndef SPL_NO_MISC
	#ifndef CONFIG_SPL_BUILD
	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(USB, usb, 0)
	#include <config_distro_bootcmd.h>
	#endif

	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x61000000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"fdt_addr_r=0x90000000\0" \
	"load_addr=0xa0000000\0" \
	"kernelheader_addr=0x60800000\0" \
	"kernel_size=0x2800000\0" \
	"kernelheader_size=0x40000\0" \
	"kernel_addr_sd=0x8000\0" \
	"kernel_size_sd=0x14000\0" \
	"kernelhdr_addr_sd=0x4000\0" \
	"kernelhdr_size_sd=0x10\0" \
	"console=ttyS0,115200\0" \
	"boot_os=y\0" \
	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
	BOOTENV \
	"boot_scripts=ls1043ardb_boot.scr\0" \
	"boot_script_hdr=hdr_ls1043ardb_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"scan_dev_for_boot=" \
	"echo Scanning ${devtype} " \
	"${devnum}:${distro_bootpart}...; " \
	"for prefix in ${boot_prefixes}; do " \
	"run scan_dev_for_scripts; " \
	"done;\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size; env exists secureboot " \
	"&& sf read $kernelheader_addr_r $kernelheader_addr " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size; env exists secureboot " \
	"&& cp.b $kernelheader_addr $kernelheader_addr_r " \
	"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
	"bootm $load_addr#$board\0" \
	"sd_bootcmd=echo Trying load from SD ..;" \
	"mmcinfo; mmc read $load_addr " \
	"$kernel_addr_sd $kernel_size_sd && " \
	"env exists secureboot && mmc read $kernelheader_addr_r " \
	"$kernelhdr_addr_sd $kernelhdr_size_sd " \
	" && esbc_validate ${kernelheader_addr_r};" \
	"bootm $load_addr#$board\0"


	#undef CONFIG_BOOTCOMMAND
	#if defined(CONFIG_QSPI_BOOT) \|\| defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
	"env exists secureboot && esbc_halt;"
	#elif defined(CONFIG_SD_BOOT)
	#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
	"env exists secureboot && esbc_halt;"
	#else
	#define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \
	"env exists secureboot && esbc_halt;"
	#endif
	#endif

	/* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */

	#define CONFIG_SYS_MAXARGS 64 /* max command args */

	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#include <asm/arch/soc.h>

	#endif /* __LS1043A_COMMON_H */