| /* |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include <dt-bindings/clock/rk3036-cru.h> |
| #include "skeleton.dtsi" |
| |
| / { |
| compatible = "rockchip,rk3036"; |
| |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| gpio0 = &gpio0; |
| gpio1 = &gpio1; |
| gpio2 = &gpio2; |
| i2c1 = &i2c1; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| mmc0 = &emmc; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x60000000 0x40000000>; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a7-pmu"; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "rockchip,rk3036-smp"; |
| |
| cpu0: cpu@f00 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf00>; |
| operating-points = < |
| /* KHz uV */ |
| 816000 1000000 |
| >; |
| #cooling-cells = <2>; /* min followed by max */ |
| clock-latency = <40000>; |
| clocks = <&cru ARMCLK>; |
| resets = <&cru SRST_CORE0>; |
| }; |
| cpu1: cpu@f01 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf01>; |
| resets = <&cru SRST_CORE1>; |
| }; |
| }; |
| |
| amba { |
| compatible = "arm,amba-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| pdma: pdma@20078000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0x20078000 0x4000>; |
| arm,pl330-broken-no-flushp; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| clocks = <&cru ACLK_DMAC2>; |
| clock-names = "apb_pclk"; |
| }; |
| }; |
| |
| xin24m: oscillator { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xin24m"; |
| #clock-cells = <0>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| arm,cpu-registers-not-fw-configured; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| clock-frequency = <24000000>; |
| }; |
| |
| cru: clock-controller@20000000 { |
| compatible = "rockchip,rk3036-cru"; |
| reg = <0x20000000 0x1000>; |
| rockchip,grf = <&grf>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| assigned-clocks = <&cru PLL_GPLL>; |
| assigned-clock-rates = <594000000>; |
| }; |
| |
| uart0: serial@20060000 { |
| compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; |
| reg = <0x20060000 0x100>; |
| interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; |
| clock-names = "baudclk", "apb_pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; |
| }; |
| |
| uart1: serial@20064000 { |
| compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; |
| reg = <0x20064000 0x100>; |
| interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; |
| clock-names = "baudclk", "apb_pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_xfer>; |
| }; |
| |
| uart2: serial@20068000 { |
| compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; |
| reg = <0x20068000 0x100>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; |
| clock-names = "baudclk", "apb_pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_xfer>; |
| }; |
| |
| pwm0: pwm@20050000 { |
| compatible = "rockchip,rk2928-pwm"; |
| reg = <0x20050000 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm0_pin>; |
| clocks = <&cru PCLK_PWM>; |
| clock-names = "pwm"; |
| status = "disabled"; |
| }; |
| |
| pwm1: pwm@20050010 { |
| compatible = "rockchip,rk2928-pwm"; |
| reg = <0x20050010 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm1_pin>; |
| clocks = <&cru PCLK_PWM>; |
| clock-names = "pwm"; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@20050020 { |
| compatible = "rockchip,rk2928-pwm"; |
| reg = <0x20050020 0x10>; |
| #pwm-cells = <3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm2_pin>; |
| clocks = <&cru PCLK_PWM>; |
| clock-names = "pwm"; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@20050030 { |
| compatible = "rockchip,rk2928-pwm"; |
| reg = <0x20050030 0x10>; |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm3_pin>; |
| clocks = <&cru PCLK_PWM>; |
| clock-names = "pwm"; |
| status = "disabled"; |
| }; |
| |
| sram: sram@10080000 { |
| compatible = "rockchip,rk3036-smp-sram", "mmio-sram"; |
| reg = <0x10080000 0x2000>; |
| }; |
| |
| gic: interrupt-controller@10139000 { |
| compatible = "arm,gic-400"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| |
| reg = <0x10139000 0x1000>, |
| <0x1013a000 0x1000>, |
| <0x1013c000 0x2000>, |
| <0x1013e000 0x2000>; |
| interrupts = <GIC_PPI 9 0xf04>; |
| }; |
| |
| grf: syscon@20008000 { |
| compatible = "rockchip,rk3036-grf", "syscon"; |
| reg = <0x20008000 0x1000>; |
| }; |
| |
| usb_otg: usb@10180000 { |
| compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", |
| "snps,dwc2"; |
| reg = <0x10180000 0x40000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_OTG0>; |
| clock-names = "otg"; |
| dr_mode = "otg"; |
| g-np-tx-fifo-size = <16>; |
| g-rx-fifo-size = <275>; |
| g-tx-fifo-size = <256 128 128 64 64 32>; |
| g-use-dma; |
| status = "disabled"; |
| }; |
| |
| usb_host: usb@101c0000 { |
| compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", |
| "snps,dwc2"; |
| reg = <0x101c0000 0x40000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_OTG1>; |
| clock-names = "otg"; |
| dr_mode = "host"; |
| status = "disabled"; |
| }; |
| |
| emmc: dwmmc@1021c000 { |
| compatible = "rockchip,rk3288-dw-mshc"; |
| clock-frequency = <37500000>; |
| clock-freq-min-max = <400000 37500000>; |
| clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, |
| <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; |
| dmas = <&pdma 12>; |
| dma-names = "rx-tx"; |
| fifo-depth = <0x100>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x1021c000 0x4000>; |
| broken-cd; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| disable-wp; |
| non-removable; |
| num-slots = <1>; |
| default-sample-phase = <158>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; |
| }; |
| |
| pinctrl: pinctrl { |
| compatible = "rockchip,rk3036-pinctrl"; |
| rockchip,grf = <&grf>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio0: gpio0@2007c000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x2007c000 0x100>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio1@20080000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x20080000 0x100>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO1>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio2@20084000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0x20084000 0x100>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO2>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pcfg_pull_up: pcfg-pull-up { |
| bias-pull-up; |
| }; |
| |
| pcfg_pull_down: pcfg-pull-down { |
| bias-pull-down; |
| }; |
| |
| pcfg_pull_none: pcfg-pull-none { |
| bias-disable; |
| }; |
| |
| emmc { |
| /* |
| * We run eMMC at max speed; bump up drive strength. |
| * We also have external pulls, so disable the internal ones. |
| */ |
| emmc_clk: emmc-clk { |
| rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none>; |
| }; |
| |
| emmc_cmd: emmc-cmd { |
| rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_none>; |
| }; |
| |
| emmc_bus8: emmc-bus8 { |
| rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>, |
| <1 25 RK_FUNC_2 &pcfg_pull_none>, |
| <1 26 RK_FUNC_2 &pcfg_pull_none>, |
| <1 27 RK_FUNC_2 &pcfg_pull_none>; |
| /* |
| <1 28 RK_FUNC_2 &pcfg_pull_up>, |
| <1 29 RK_FUNC_2 &pcfg_pull_up>, |
| <1 30 RK_FUNC_2 &pcfg_pull_up>, |
| <1 31 RK_FUNC_2 &pcfg_pull_up>; |
| */ |
| }; |
| }; |
| |
| uart0 { |
| uart0_xfer: uart0-xfer { |
| rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_none>, |
| <0 17 RK_FUNC_1 &pcfg_pull_none>; |
| }; |
| |
| uart0_cts: uart0-cts { |
| rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_none>; |
| }; |
| |
| uart0_rts: uart0-rts { |
| rockchip,pins = <0 19 RK_FUNC_1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| uart1 { |
| uart1_xfer: uart1-xfer { |
| rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_none>, |
| <2 23 RK_FUNC_1 &pcfg_pull_none>; |
| }; |
| /* no rts / cts for uart1 */ |
| }; |
| |
| uart2 { |
| uart2_xfer: uart2-xfer { |
| rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>, |
| <1 19 RK_FUNC_2 &pcfg_pull_none>; |
| }; |
| /* no rts / cts for uart2 */ |
| }; |
| |
| pwm0 { |
| pwm0_pin: pwm0-pin { |
| rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm1 { |
| pwm1_pin: pwm1-pin { |
| rockchip,pins = <0 1 RK_FUNC_2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm2 { |
| pwm2_pin: pwm2-pin { |
| rockchip,pins = <0 1 2 &pcfg_pull_none>; |
| }; |
| }; |
| |
| pwm3 { |
| pwm3_pin: pwm3-pin { |
| rockchip,pins = <0 27 1 &pcfg_pull_none>; |
| }; |
| }; |
| |
| i2c1 { |
| i2c1_xfer: i2c1-xfer { |
| rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>, |
| <0 3 RK_FUNC_1 &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| i2c1: i2c@20056000 { |
| compatible = "rockchip,rk3288-i2c"; |
| reg = <0x20056000 0x1000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-names = "i2c"; |
| clocks = <&cru PCLK_I2C1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_xfer>; |
| status = "disabled"; |
| }; |
| }; |