include/configs/ZPC1900.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2003-2005 Arabella Software Ltd.
  * Yuli Barcohen <yuli@arabellasw.com>
  *
  * U-Boot configuration for Zephyr Engineering ZPC.1900 board.
  * This port was developed and tested on Revision C board.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_ZPC1900		1	/* ...on Zephyr ZPC.1900 board */

 #define	CONFIG_SYS_TEXT_BASE	0xFE000000

 #define CPU_ID_STR		"MPC8265"
 #define CONFIG_CPM2		1	/* Has a CPM2 */

 /* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
 #define CONFIG_ENV_OVERWRITE

 /*
  * Select serial console configuration
  *
  * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
  * for SCC).
  */
 #define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
 #undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
 #undef	CONFIG_CONS_NONE		/* It's not on external UART */
 #define CONFIG_CONS_INDEX	1	/* SMC1 is used for console  */

 /*
  * Select ethernet configuration
  *
  * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
  * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
  * SCC, 1-3 for FCC)
  *
  * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
  * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
  * must be unset.
  */
 #undef	CONFIG_ETHER_ON_SCC		/* Ethernet is not on SCC */
 #define CONFIG_ETHER_ON_FCC		/* Ethernet is on FCC     */
 #undef	CONFIG_ETHER_NONE		/* No external Ethernet   */

 #ifdef CONFIG_ETHER_ON_FCC

 #define CONFIG_ETHER_INDEX	2	/* FCC2 is used for Ethernet */

 #if (CONFIG_ETHER_INDEX == 2)
 /*
  * - Rx clock is CLK13
  * - Tx clock is CLK14
  * - Select bus for bd/buffers (see 28-13)
  * - Full duplex
  */
 # define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
 # define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
 # define CONFIG_SYS_CPMFCR_RAMTYPE	0
 # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)

 #endif /* CONFIG_ETHER_INDEX */

 #define CONFIG_MII			/* MII PHY management        */
 #define CONFIG_BITBANGMII		/* Bit-banged MDIO interface */
 /*
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		2	/* Port C */
 #define MDIO_DECLARE		volatile ioport_t *iop = ioport_addr ( \
 					(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
 #define MDC_DECLARE		MDIO_DECLARE

 #define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
 #define MDIO_READ		((iop->pdat &  0x00400000) != 0)

 #define MDIO(bit)		if(bit) iop->pdat |=  0x00400000; \
 				else	iop->pdat &= ~0x00400000

 #define MDC(bit)		if(bit) iop->pdat |=  0x00200000; \
 				else	iop->pdat &= ~0x00200000

 #define MIIDELAY		udelay(1)

 #endif /* CONFIG_ETHER_ON_FCC */

 #ifndef CONFIG_8260_CLKIN
 #define CONFIG_8260_CLKIN	66666666	/* in Hz */
 #endif

 #define CONFIG_BAUDRATE		38400


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING


 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 #define CONFIG_BOOTCOMMAND	"dhcp;bootm"	/* autoboot command */
 #define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=:::::eth0:dhcp"

 #if defined(CONFIG_CMD_KGDB)
 #undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
 #define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
 #undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
 #define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
 #endif

 #define CONFIG_BZIP2	/* include support for bzip2 compressed images */
 #undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size  */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size  */

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x03800000	/* 1 ... 56 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x400000	/* default load address */

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_SIZE		64

 #define CONFIG_SYS_IMMR		0xF0000000
 #define CONFIG_SYS_LSDRAM_BASE		0xFC000000
 #define CONFIG_SYS_FLASH_BASE		0xFE000000
 #define CONFIG_SYS_BCSR		0xFEA00000
 #define CONFIG_SYS_EEPROM		0xFEB00000
 #define CONFIG_SYS_FLSIMM_BASE		0xFF000000

 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of flash banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	32	/* max num of sects on one chip */

 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE }

 #define BCSR_PCI_MODE		0x01

 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /* Hard reset configuration word */
 #define CONFIG_SYS_HRCW_MASTER		(HRCW_EBM | HRCW_BPS01| HRCW_CIP          |\
 				 HRCW_L2CPC10 | HRCW_DPPC00 | HRCW_ISB100 |\
 				 HRCW_BMS | HRCW_LBPC00 | HRCW_APPC10     |\
 				 HRCW_MODCK_H0111                          \
 				) /* 0x16848207 */
 /* No slaves */
 #define CONFIG_SYS_HRCW_SLAVE1		0
 #define CONFIG_SYS_HRCW_SLAVE2		0
 #define CONFIG_SYS_HRCW_SLAVE3		0
 #define CONFIG_SYS_HRCW_SLAVE4		0
 #define CONFIG_SYS_HRCW_SLAVE5		0
 #define CONFIG_SYS_HRCW_SLAVE6		0
 #define CONFIG_SYS_HRCW_SLAVE7		0

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve 4 MB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 #if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM)
 #define CONFIG_ENV_IS_IN_NVRAM	1
 #endif

 #ifdef CONFIG_ENV_IS_IN_FLASH
 #  define CONFIG_ENV_SECT_SIZE	0x10000
 #  define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #else
 #  define CONFIG_ENV_ADDR		(CONFIG_SYS_EEPROM + 0x400)
 #  define CONFIG_ENV_SIZE		0x1000
 #  define CONFIG_SYS_NVRAM_ACCESS_ROUTINE
 #endif

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 #define CONFIG_SYS_HID0_INIT		(HID0_ICFI)
 #define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE)

 #define CONFIG_SYS_HID2		0

 #define CONFIG_SYS_SIUMCR		0x42200000
 #define CONFIG_SYS_SYPCR		0xFFFFFFC3
 #define CONFIG_SYS_BCR			0x90000000
 #define CONFIG_SYS_SCCR		SCCR_DFBRG01

 #define CONFIG_SYS_RMR			RMR_CSRE
 #define CONFIG_SYS_TMCNTSC		(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
 #define CONFIG_SYS_PISCR		(PISCR_PS|PISCR_PTF|PISCR_PTE)
 #define CONFIG_SYS_RCCR		0

 #define CONFIG_SYS_PSDMR		/* 0x834DA43B */0x014DA43A
 #define CONFIG_SYS_PSRT		0x0F/* 0x0C */
 #define CONFIG_SYS_LSDMR		0x0085A562
 #define CONFIG_SYS_LSRT		0x0F
 #define CONFIG_SYS_MPTPR		0x4000

 #define CONFIG_SYS_PSDRAM_BR		(CONFIG_SYS_SDRAM_BASE | 0x00000041)
 #define CONFIG_SYS_PSDRAM_OR		0xFC0028C0
 #define CONFIG_SYS_LSDRAM_BR		(CONFIG_SYS_LSDRAM_BASE | 0x00001861)
 #define CONFIG_SYS_LSDRAM_OR		0xFF803480

 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | 0x00000801)
 #define CONFIG_SYS_OR0_PRELIM		0xFFE00856
 #define CONFIG_SYS_BR5_PRELIM		(CONFIG_SYS_EEPROM | 0x00000801)
 #define CONFIG_SYS_OR5_PRELIM		0xFFFF03F6
 #define CONFIG_SYS_BR6_PRELIM		(CONFIG_SYS_FLSIMM_BASE | 0x00001801)
 #define CONFIG_SYS_OR6_PRELIM		0xFF000856
 #define CONFIG_SYS_BR7_PRELIM		(CONFIG_SYS_BCSR | 0x00000801)
 #define CONFIG_SYS_OR7_PRELIM		0xFFFF83F6

 #define CONFIG_SYS_RESET_ADDRESS	0xC0000000

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2003-2005 Arabella Software Ltd.
	* Yuli Barcohen <yuli@arabellasw.com>
	*
	* U-Boot configuration for Zephyr Engineering ZPC.1900 board.
	* This port was developed and tested on Revision C board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_ZPC1900 1 /* ...on Zephyr ZPC.1900 board */

	#define CONFIG_SYS_TEXT_BASE 0xFE000000

	#define CPU_ID_STR "MPC8265"
	#define CONFIG_CPM2 1 /* Has a CPM2 */

	/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
	#define CONFIG_ENV_OVERWRITE

	/*
	* Select serial console configuration
	*
	* If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
	* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
	* for SCC).
	*/
	#define CONFIG_CONS_ON_SMC /* Console is on SMC */
	#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
	#undef CONFIG_CONS_NONE /* It's not on external UART */
	#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */

	/*
	* Select ethernet configuration
	*
	* If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
	* then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
	* SCC, 1-3 for FCC)
	*
	* If CONFIG_ETHER_NONE is defined, then either the ethernet routines
	* must be defined elsewhere (as for the console), or CONFIG_CMD_NET
	* must be unset.
	*/
	#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
	#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
	#undef CONFIG_ETHER_NONE /* No external Ethernet */

	#ifdef CONFIG_ETHER_ON_FCC

	#define CONFIG_ETHER_INDEX 2 /* FCC2 is used for Ethernet */

	#if (CONFIG_ETHER_INDEX == 2)
	/*
	* - Rx clock is CLK13
	* - Tx clock is CLK14
	* - Select bus for bd/buffers (see 28-13)
	* - Full duplex
	*/
	# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 \| CMXFCR_RF2CS_MSK \| CMXFCR_TF2CS_MSK)
	# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 \| CMXFCR_TF2CS_CLK14)
	# define CONFIG_SYS_CPMFCR_RAMTYPE 0
	# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE \| FCC_PSMR_LPB)

	#endif /* CONFIG_ETHER_INDEX */

	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
	/*
	* GPIO pins used for bit-banged MII communications
	*/
	#define MDIO_PORT 2 /* Port C */
	#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
	(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
	#define MDC_DECLARE MDIO_DECLARE

	#define MDIO_ACTIVE (iop->pdir \|= 0x00400000)
	#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
	#define MDIO_READ ((iop->pdat & 0x00400000) != 0)

	#define MDIO(bit) if(bit) iop->pdat \|= 0x00400000; \
	else iop->pdat &= ~0x00400000

	#define MDC(bit) if(bit) iop->pdat \|= 0x00200000; \
	else iop->pdat &= ~0x00200000

	#define MIIDELAY udelay(1)

	#endif /* CONFIG_ETHER_ON_FCC */

	#ifndef CONFIG_8260_CLKIN
	#define CONFIG_8260_CLKIN 66666666 /* in Hz */
	#endif

	#define CONFIG_BAUDRATE 38400


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_PING


	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	#define CONFIG_BOOTCOMMAND "dhcp;bootm" /* autoboot command */
	#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=:::::eth0:dhcp"

	#if defined(CONFIG_CMD_KGDB)
	#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
	#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
	#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
	#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
	#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
	#endif

	#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
	#undef CONFIG_WATCHDOG /* disable platform specific watchdog */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x03800000 /* 1 ... 56 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_SIZE 64

	#define CONFIG_SYS_IMMR 0xF0000000
	#define CONFIG_SYS_LSDRAM_BASE 0xFC000000
	#define CONFIG_SYS_FLASH_BASE 0xFE000000
	#define CONFIG_SYS_BCSR 0xFEA00000
	#define CONFIG_SYS_EEPROM 0xFEB00000
	#define CONFIG_SYS_FLSIMM_BASE 0xFF000000

	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */

	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE }

	#define BCSR_PCI_MODE 0x01

	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/* Hard reset configuration word */
	#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM \| HRCW_BPS01\| HRCW_CIP \|\
	HRCW_L2CPC10 \| HRCW_DPPC00 \| HRCW_ISB100 \|\
	HRCW_BMS \| HRCW_LBPC00 \| HRCW_APPC10 \|\
	HRCW_MODCK_H0111 \
	) /* 0x16848207 */
	/* No slaves */
	#define CONFIG_SYS_HRCW_SLAVE1 0
	#define CONFIG_SYS_HRCW_SLAVE2 0
	#define CONFIG_SYS_HRCW_SLAVE3 0
	#define CONFIG_SYS_HRCW_SLAVE4 0
	#define CONFIG_SYS_HRCW_SLAVE5 0
	#define CONFIG_SYS_HRCW_SLAVE6 0
	#define CONFIG_SYS_HRCW_SLAVE7 0

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM)
	#define CONFIG_ENV_IS_IN_NVRAM 1
	#endif

	#ifdef CONFIG_ENV_IS_IN_FLASH
	# define CONFIG_ENV_SECT_SIZE 0x10000
	# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#else
	# define CONFIG_ENV_ADDR (CONFIG_SYS_EEPROM + 0x400)
	# define CONFIG_ENV_SIZE 0x1000
	# define CONFIG_SYS_NVRAM_ACCESS_ROUTINE
	#endif

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	#define CONFIG_SYS_HID0_INIT (HID0_ICFI)
	#define CONFIG_SYS_HID0_FINAL (HID0_ICE \| HID0_IFEM \| HID0_ABE)

	#define CONFIG_SYS_HID2 0

	#define CONFIG_SYS_SIUMCR 0x42200000
	#define CONFIG_SYS_SYPCR 0xFFFFFFC3
	#define CONFIG_SYS_BCR 0x90000000
	#define CONFIG_SYS_SCCR SCCR_DFBRG01

	#define CONFIG_SYS_RMR RMR_CSRE
	#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC\|TMCNTSC_ALR\|TMCNTSC_TCF\|TMCNTSC_TCE)
	#define CONFIG_SYS_PISCR (PISCR_PS\|PISCR_PTF\|PISCR_PTE)
	#define CONFIG_SYS_RCCR 0

	#define CONFIG_SYS_PSDMR /* 0x834DA43B */0x014DA43A
	#define CONFIG_SYS_PSRT 0x0F/* 0x0C */
	#define CONFIG_SYS_LSDMR 0x0085A562
	#define CONFIG_SYS_LSRT 0x0F
	#define CONFIG_SYS_MPTPR 0x4000

	#define CONFIG_SYS_PSDRAM_BR (CONFIG_SYS_SDRAM_BASE \| 0x00000041)
	#define CONFIG_SYS_PSDRAM_OR 0xFC0028C0
	#define CONFIG_SYS_LSDRAM_BR (CONFIG_SYS_LSDRAM_BASE \| 0x00001861)
	#define CONFIG_SYS_LSDRAM_OR 0xFF803480

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| 0x00000801)
	#define CONFIG_SYS_OR0_PRELIM 0xFFE00856
	#define CONFIG_SYS_BR5_PRELIM (CONFIG_SYS_EEPROM \| 0x00000801)
	#define CONFIG_SYS_OR5_PRELIM 0xFFFF03F6
	#define CONFIG_SYS_BR6_PRELIM (CONFIG_SYS_FLSIMM_BASE \| 0x00001801)
	#define CONFIG_SYS_OR6_PRELIM 0xFF000856
	#define CONFIG_SYS_BR7_PRELIM (CONFIG_SYS_BCSR \| 0x00000801)
	#define CONFIG_SYS_OR7_PRELIM 0xFFFF83F6

	#define CONFIG_SYS_RESET_ADDRESS 0xC0000000

	#endif /* __CONFIG_H */