blob: 470f64d5a7489684dbaec11a07b002d79d672d98 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Copyright 2022 Toradex
*/
#ifndef __VERDIN_IMX8MP_H
#define __VERDIN_IMX8MP_H
#include <asm/arch/imx-regs.h>
#include <linux/sizes.h>
#define CONFIG_SPL_MAX_SIZE (152 * 1024)
#define CONFIG_SYS_MONITOR_LEN SZ_512K
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_STACK 0x960000
#define CONFIG_SPL_BSS_START_ADDR 0x0098fc00
#define CONFIG_SPL_BSS_MAX_SIZE SZ_1K
#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_512K
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR 0x184000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#define CONFIG_POWER_PCA9450
#define CONFIG_SYS_I2C
#endif /* CONFIG_SPL_BUILD */
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_FEC_MXC_PHYADDR 7
#define PHY_ANEG_TIMEOUT 20000
#endif /* CONFIG_CMD_NET */
#define MEM_LAYOUT_ENV_SETTINGS \
"fdt_addr_r=0x43000000\0" \
"kernel_addr_r=0x40000000\0" \
"ramdisk_addr_r=0x46400000\0" \
"scriptaddr=0x46000000\0"
/* Enable Distro Boot */
#ifndef CONFIG_SPL_BUILD
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 2) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#else
#define BOOTENV
#endif
#if defined(CONFIG_TDX_EASY_INSTALLER)
# define BOOT_SCRIPT "boot-tezi.scr"
#else
# define BOOT_SCRIPT "boot.scr"
#endif
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
BOOTENV \
MEM_LAYOUT_ENV_SETTINGS \
"bootcmd_mfg=fastboot 0\0" \
"boot_file=Image\0" \
"boot_scripts=" BOOT_SCRIPT "\0" \
"boot_script_dhcp=" BOOT_SCRIPT "\0" \
"console=ttymxc2\0" \
"fdt_board=dev\0" \
"initrd_addr=0x43800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"setup=setenv setupargs console=${console},${baudrate} console=tty1 " \
"consoleblank=0 earlycon\0" \
"update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
"if test \"$confirm\" = \"y\"; then " \
"setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt " \
"${blkcnt} / 0x200; mmc dev 2 1; mmc write ${loadaddr} 0x0 " \
"${blkcnt}; fi\0"
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE SZ_512K
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_SYS_BOOTM_LEN SZ_64M /* Increase max gunzip size */
/* i.MX 8M Plus supports max. 8GB memory in two albeit concecutive banks */
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE (SZ_2G + SZ_1G)
#define PHYS_SDRAM_2 0x100000000
#define PHYS_SDRAM_2_SIZE (SZ_4G + SZ_1G)
/* UART */
#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(3)
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE SZ_2K
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#endif /* __VERDIN_IMX8MP_H */