| /* |
| * Copyright (c) 2008 Nuovation System Designs, LLC |
| * Grant Erickson <gerickson@nuovations.com> |
| * |
| * (C) Copyright 2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /************************************************************************ |
| * kilauea.h - configuration for AMCC Kilauea (405EX) |
| ***********************************************************************/ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_KILAUEA 1 /* Board is Kilauea */ |
| #define CONFIG_405EX 1 /* Specifc 405EX support*/ |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFFA0000 |
| #endif |
| |
| /* |
| * CHIP_21 errata - you must set this to match your exact CPU, else your |
| * board will not boot. DO NOT enable this unless you have JTAG available |
| * for recovery, in the event you get it wrong. |
| * |
| * Kilauea uses the 405EX, while Haleakala uses the 405EXr. Either board |
| * may be equipped for security or not. You must look at the CPU part |
| * number to be sure what you have. |
| */ |
| /* #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY */ |
| /* #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY */ |
| /* #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY */ |
| /* #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY */ |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #define CONFIG_HOSTNAME kilauea |
| #include "amcc-common.h" |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ |
| #define CONFIG_BOARD_TYPES |
| #define CONFIG_BOARD_EMAC_COUNT |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_FLASH_BASE 0xFC000000 |
| #define CONFIG_SYS_NAND_ADDR 0xF8000000 |
| #define CONFIG_SYS_FPGA_BASE 0xF0000000 |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & Stack Pointer Configuration Options |
| * |
| * There are traditionally three options for the primordial |
| * (i.e. initial) stack usage on the 405-series: |
| * |
| * 1) On-chip Memory (OCM) (i.e. SRAM) |
| * 2) Data cache |
| * 3) SDRAM |
| * |
| * For the 405EX(r), there is no OCM, so we are left with (2) or (3) |
| * the latter of which is less than desireable since it requires |
| * setting up the SDRAM and ECC in assembly code. |
| * |
| * To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip |
| * select on the External Bus Controller (EBC) and then select a |
| * value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid, |
| * physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and |
| * select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid, |
| * physical SDRAM to use (3). |
| *-----------------------------------------------------------------------*/ |
| |
| #define CONFIG_SYS_INIT_DCACHE_CS 4 |
| |
| #if defined(CONFIG_SYS_INIT_DCACHE_CS) |
| #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */ |
| #endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ |
| |
| #define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * If the data cache is being used for the primordial stack and global |
| * data area, the POST word must be placed somewhere else. The General |
| * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves |
| * its compare and mask register contents across reset, so it is used |
| * for the POST word. |
| */ |
| |
| #if defined(CONFIG_SYS_INIT_DCACHE_CS) |
| # define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| # define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) |
| #else |
| # define CONFIG_SYS_INIT_EXTRA_SIZE 16 |
| # define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE) |
| # define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR |
| #endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| |
| /*----------------------------------------------------------------------- |
| * Environment |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH related |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif /* CONFIG_ENV_IS_IN_FLASH */ |
| |
| /*----------------------------------------------------------------------- |
| * NAND FLASH |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) |
| #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ |
| |
| /* |
| * CONFIG_PPC4xx_DDR_AUTOCALIBRATION |
| * |
| * Note: DDR Autocalibration Method_A scans the full range of possible PPC4xx |
| * SDRAM Controller DDR autocalibration values and takes a lot longer |
| * to run than Method_B. |
| * (See the Method_A and Method_B algorithm discription in the file: |
| * arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c) |
| * Define CONFIG_PPC4xx_DDR_METHOD_A to use DDR autocalibration Method_A |
| * |
| * DDR Autocalibration Method_B is the default. |
| */ |
| #define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ |
| #define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ |
| #undef CONFIG_PPC4xx_DDR_METHOD_A |
| |
| #define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE) |
| |
| /* DDR1/2 SDRAM Device Control Register Data Values */ |
| #define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) | \ |
| SDRAM_RXBAS_SDSZ_256MB | \ |
| SDRAM_RXBAS_SDAM_MODE7 | \ |
| SDRAM_RXBAS_SDBE_ENABLE) |
| #define CONFIG_SYS_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE |
| #define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE |
| #define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE |
| #define CONFIG_SYS_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \ |
| SDRAM_MCOPT1_8_BANKS | \ |
| SDRAM_MCOPT1_DDR2_TYPE | \ |
| SDRAM_MCOPT1_QDEP | \ |
| SDRAM_MCOPT1_DCOO_DISABLED) |
| #define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \ |
| SDRAM_MODT_EB0R_ENABLE) |
| #define CONFIG_SYS_SDRAM0_MODT1 0x00000000 |
| #define CONFIG_SYS_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \ |
| SDRAM_CODT_CKLZ_36OHM | \ |
| SDRAM_CODT_DQS_1_8_V_DDR2 | \ |
| SDRAM_CODT_IO_NMODE) |
| #define CONFIG_SYS_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560) |
| #define CONFIG_SYS_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(80) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP)) |
| #define CONFIG_SYS_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(3) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) |
| #define CONFIG_SYS_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL)) |
| #define CONFIG_SYS_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \ |
| SDRAM_INITPLR_IMA_ENCODE(0)) |
| #define CONFIG_SYS_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \ |
| JEDEC_MA_EMR_RTT_75OHM)) |
| #define CONFIG_SYS_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \ |
| JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ |
| JEDEC_MA_MR_BLEN_4 | \ |
| JEDEC_MA_MR_DLL_RESET)) |
| #define CONFIG_SYS_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(3) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ |
| SDRAM_INITPLR_IBA_ENCODE(0x0) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) |
| #define CONFIG_SYS_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(26) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) |
| #define CONFIG_SYS_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(26) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) |
| #define CONFIG_SYS_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(26) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) |
| #define CONFIG_SYS_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(26) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) |
| #define CONFIG_SYS_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \ |
| JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ |
| JEDEC_MA_MR_BLEN_4)) |
| #define CONFIG_SYS_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER | \ |
| JEDEC_MA_EMR_RDQS_DISABLE | \ |
| JEDEC_MA_EMR_DQS_DISABLE | \ |
| JEDEC_MA_EMR_RTT_DISABLED | \ |
| JEDEC_MA_EMR_ODS_NORMAL)) |
| #define CONFIG_SYS_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \ |
| SDRAM_INITPLR_IMWT_ENCODE(2) | \ |
| SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ |
| SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ |
| SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \ |
| JEDEC_MA_EMR_RDQS_DISABLE | \ |
| JEDEC_MA_EMR_DQS_DISABLE | \ |
| JEDEC_MA_EMR_RTT_DISABLED | \ |
| JEDEC_MA_EMR_ODS_NORMAL)) |
| #define CONFIG_SYS_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE) |
| #define CONFIG_SYS_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE) |
| #define CONFIG_SYS_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \ |
| SDRAM_RQDC_RQFD_ENCODE(56)) |
| #define CONFIG_SYS_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521) |
| #define CONFIG_SYS_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2) |
| #define CONFIG_SYS_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \ |
| SDRAM_DLCR_DLCS_CONT_DONE | \ |
| SDRAM_DLCR_DLCV_ENCODE(165)) |
| #define CONFIG_SYS_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV) |
| #define CONFIG_SYS_SDRAM0_WRDTR 0x00000000 |
| #define CONFIG_SYS_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \ |
| SDRAM_SDTR1_RTW_2_CLK | \ |
| SDRAM_SDTR1_RTRO_1_CLK) |
| #define CONFIG_SYS_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \ |
| SDRAM_SDTR2_WTR_2_CLK | \ |
| SDRAM_SDTR2_XSNR_32_CLK | \ |
| SDRAM_SDTR2_WPC_4_CLK | \ |
| SDRAM_SDTR2_RPC_2_CLK | \ |
| SDRAM_SDTR2_RP_3_CLK | \ |
| SDRAM_SDTR2_RRD_2_CLK) |
| #define CONFIG_SYS_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \ |
| SDRAM_SDTR3_RC_ENCODE(11) | \ |
| SDRAM_SDTR3_XCS | \ |
| SDRAM_SDTR3_RFC_ENCODE(26)) |
| #define CONFIG_SYS_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \ |
| SDRAM_MMODE_DCL_DDR2_4_0_CLK | \ |
| SDRAM_MMODE_BLEN_4) |
| #define CONFIG_SYS_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \ |
| SDRAM_MEMODE_RTT_75OHM) |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| |
| /* I2C bootstrap EEPROM */ |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52 |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 |
| #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 |
| |
| /* Standard DTT sensor configuration */ |
| #define CONFIG_DTT_DS1775 1 |
| #define CONFIG_DTT_SENSORS { 0 } |
| #define CONFIG_SYS_I2C_DTT_ADDR 0x48 |
| |
| /* RTC configuration */ |
| #define CONFIG_RTC_DS1338 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| |
| /*----------------------------------------------------------------------- |
| * Ethernet |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_M88E1111_PHY 1 |
| #define CONFIG_IBM_EMAC4_V4 1 |
| #define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII |
| #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ |
| |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| #define CONFIG_HAS_ETH0 1 |
| |
| #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ |
| #define CONFIG_PHY1_ADDR 2 |
| |
| /* Debug messages for the DDR autocalibration */ |
| #define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_PPC_OLD \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "logversion=2\0" \ |
| "kernel_addr=fc000000\0" \ |
| "fdt_addr=fc1e0000\0" \ |
| "ramdisk_addr=fc200000\0" \ |
| "pciconfighost=1\0" \ |
| "pcie_mode=RP:RP\0" \ |
| "" |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_CHIP_CONFIG |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_PCI |
| |
| #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY |
| |
| /* POST support */ |
| #define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ |
| CONFIG_SYS_POST_CPU | \ |
| CONFIG_SYS_POST_ETHER | \ |
| CONFIG_SYS_POST_I2C | \ |
| CONFIG_SYS_POST_MEMORY_ON | \ |
| CONFIG_SYS_POST_UART) |
| |
| /* Define here the base-addresses of the UARTs to test in POST */ |
| #define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ |
| CONFIG_SYS_NS16550_COM2 } |
| |
| #define CONFIG_LOGBUFFER |
| #define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE |
| |
| /*----------------------------------------------------------------------- |
| * PCIe stuff |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ |
| #define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ |
| |
| #define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */ |
| #define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */ |
| #define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ |
| |
| #define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */ |
| #define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */ |
| #define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ |
| |
| #define CONFIG_SYS_PCIE0_UTLBASE 0xef502000 |
| #define CONFIG_SYS_PCIE1_UTLBASE 0xef503000 |
| |
| /* base address of inbound PCIe window */ |
| #define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_NAND_CS 1 /* NAND chip connected to CSx */ |
| |
| /* Memory Bank 0 (NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x05806500 |
| #define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ |
| |
| /* Memory Bank 1 (NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB1AP 0x018003c0 |
| #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_ADDR | 0x1e000) |
| |
| /* Memory Bank 2 (FPGA) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_ENABLED | \ |
| EBC_BXAP_FWT_ENCODE(6) | \ |
| EBC_BXAP_BWT_ENCODE(1) | \ |
| EBC_BXAP_BCE_DISABLE | \ |
| EBC_BXAP_BCT_2TRANS | \ |
| EBC_BXAP_CSN_ENCODE(0) | \ |
| EBC_BXAP_OEN_ENCODE(0) | \ |
| EBC_BXAP_WBN_ENCODE(3) | \ |
| EBC_BXAP_WBF_ENCODE(1) | \ |
| EBC_BXAP_TH_ENCODE(4) | \ |
| EBC_BXAP_RE_DISABLED | \ |
| EBC_BXAP_SOR_DELAYED | \ |
| EBC_BXAP_BEM_WRITEONLY | \ |
| EBC_BXAP_PEN_DISABLED) |
| #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE | 0x18000) |
| |
| #define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */ |
| |
| /*----------------------------------------------------------------------- |
| * GPIO Setup |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \ |
| } \ |
| } |
| |
| /*----------------------------------------------------------------------- |
| * Some Kilauea stuff..., mainly fpga registers |
| */ |
| #define CONFIG_SYS_FPGA_REG_BASE CONFIG_SYS_FPGA_BASE |
| #define CONFIG_SYS_FPGA_FIFO_BASE (CONFIG_SYS_FPGA_BASE | (1 << 10)) |
| |
| /* interrupt */ |
| #define CONFIG_SYS_FPGA_SLIC0_R_DPRAM_INT 0x80000000 |
| #define CONFIG_SYS_FPGA_SLIC0_W_DPRAM_INT 0x40000000 |
| #define CONFIG_SYS_FPGA_SLIC1_R_DPRAM_INT 0x20000000 |
| #define CONFIG_SYS_FPGA_SLIC1_W_DPRAM_INT 0x10000000 |
| #define CONFIG_SYS_FPGA_PHY0_INT 0x08000000 |
| #define CONFIG_SYS_FPGA_PHY1_INT 0x04000000 |
| #define CONFIG_SYS_FPGA_SLIC0_INT 0x02000000 |
| #define CONFIG_SYS_FPGA_SLIC1_INT 0x01000000 |
| |
| /* DPRAM setting */ |
| /* 00: 32B; 01: 64B; 10: 128B; 11: 256B */ |
| #define CONFIG_SYS_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */ |
| #define CONFIG_SYS_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */ |
| #define CONFIG_SYS_FPGA_DPRAM_RW_TYPE 0x00080000 |
| #define CONFIG_SYS_FPGA_DPRAM_RST 0x00040000 |
| #define CONFIG_SYS_FPGA_UART0_FO 0x00020000 |
| #define CONFIG_SYS_FPGA_UART1_FO 0x00010000 |
| |
| /* loopback */ |
| #define CONFIG_SYS_FPGA_CHIPSIDE_LOOPBACK 0x00004000 |
| #define CONFIG_SYS_FPGA_LINESIDE_LOOPBACK 0x00008000 |
| #define CONFIG_SYS_FPGA_SLIC0_ENABLE 0x00002000 |
| #define CONFIG_SYS_FPGA_SLIC1_ENABLE 0x00001000 |
| #define CONFIG_SYS_FPGA_SLIC0_CS 0x00000800 |
| #define CONFIG_SYS_FPGA_SLIC1_CS 0x00000400 |
| #define CONFIG_SYS_FPGA_USER_LED0 0x00000200 |
| #define CONFIG_SYS_FPGA_USER_LED1 0x00000100 |
| |
| #define CONFIG_SYS_FPGA_MAGIC_MASK 0xffff0000 |
| #define CONFIG_SYS_FPGA_MAGIC 0xabcd0000 |
| #define CONFIG_SYS_FPGA_VER_MASK 0x0000ff00 |
| |
| #endif /* __CONFIG_H */ |