| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ |
| */ |
| |
| #include <dt-bindings/bus/ti-sysc.h> |
| #include <dt-bindings/clock/omap4.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/pinctrl/omap.h> |
| #include <dt-bindings/clock/omap4.h> |
| |
| / { |
| compatible = "ti,omap4430", "ti,omap4"; |
| interrupt-parent = <&wakeupgen>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| chosen { }; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| next-level-cache = <&L2>; |
| reg = <0x0>; |
| |
| clocks = <&dpll_mpu_ck>; |
| clock-names = "cpu"; |
| |
| clock-latency = <300000>; /* From omap-cpufreq driver */ |
| }; |
| cpu@1 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| next-level-cache = <&L2>; |
| reg = <0x1>; |
| }; |
| }; |
| |
| /* |
| * Note that 4430 needs cross trigger interface (CTI) supported |
| * before we can configure the interrupts. This means sampling |
| * events are not supported for pmu. Note that 4460 does not use |
| * CTI, see also 4460.dtsi. |
| */ |
| pmu { |
| compatible = "arm,cortex-a9-pmu"; |
| ti,hwmods = "debugss"; |
| }; |
| |
| gic: interrupt-controller@48241000 { |
| compatible = "arm,cortex-a9-gic"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x48241000 0x1000>, |
| <0x48240100 0x0100>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| L2: l2-cache-controller@48242000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x48242000 0x1000>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| local-timer@48240600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| clocks = <&mpu_periphclk>; |
| reg = <0x48240600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| wakeupgen: interrupt-controller@48281000 { |
| compatible = "ti,omap4-wugen-mpu"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x48281000 0x1000>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| /* |
| * The soc node represents the soc top level view. It is used for IPs |
| * that are not memory mapped in the MPU view or for the MPU itself. |
| */ |
| soc { |
| compatible = "ti,omap-infra"; |
| mpu { |
| compatible = "ti,omap4-mpu"; |
| ti,hwmods = "mpu"; |
| sram = <&ocmcram>; |
| }; |
| |
| dsp { |
| compatible = "ti,omap3-c64"; |
| }; |
| |
| iva { |
| compatible = "ti,ivahd"; |
| ti,hwmods = "iva"; |
| }; |
| }; |
| |
| /* |
| * XXX: Use a flat representation of the OMAP4 interconnect. |
| * The real OMAP interconnect network is quite complex. |
| * Since it will not bring real advantage to represent that in DT for |
| * the moment, just use a fake OCP bus entry to represent the whole bus |
| * hierarchy. |
| */ |
| ocp { |
| compatible = "ti,omap4-l3-noc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; |
| reg = <0x44000000 0x1000>, |
| <0x44800000 0x2000>, |
| <0x45000000 0x1000>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| |
| l4_wkup: interconnect@4a300000 { |
| }; |
| |
| l4_cfg: interconnect@4a000000 { |
| }; |
| |
| l4_per: interconnect@48000000 { |
| }; |
| |
| l4_abe: interconnect@40100000 { |
| }; |
| |
| ocmcram: sram@40304000 { |
| compatible = "mmio-sram"; |
| reg = <0x40304000 0xa000>; /* 40k */ |
| }; |
| |
| gpmc: gpmc@50000000 { |
| compatible = "ti,omap4430-gpmc"; |
| reg = <0x50000000 0x1000>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 4>; |
| dma-names = "rxtx"; |
| gpmc,num-cs = <8>; |
| gpmc,num-waitpins = <4>; |
| ti,hwmods = "gpmc"; |
| ti,no-idle-on-init; |
| clocks = <&l3_div_ck>; |
| clock-names = "fck"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| target-module@52000000 { |
| compatible = "ti,sysc-omap4", "ti,sysc"; |
| ti,hwmods = "iss"; |
| reg = <0x52000000 0x4>, |
| <0x52000010 0x4>; |
| reg-names = "rev", "sysc"; |
| ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>; |
| ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| ti,sysc-delay-us = <2>; |
| clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x52000000 0x1000000>; |
| |
| /* No child device binding, driver in staging */ |
| }; |
| |
| target-module@55082000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x55082000 0x4>, |
| <0x55082010 0x4>, |
| <0x55082014 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| clocks = <&ducati_clkctrl OMAP4_IPU_CLKCTRL 0>; |
| clock-names = "fck"; |
| resets = <&prm_core 2>; |
| reset-names = "rstctrl"; |
| ranges = <0x0 0x55082000 0x100>; |
| #size-cells = <1>; |
| #address-cells = <1>; |
| |
| mmu_ipu: mmu@0 { |
| compatible = "ti,omap4-iommu"; |
| reg = <0x0 0x100>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| #iommu-cells = <0>; |
| ti,iommu-bus-err-back; |
| }; |
| }; |
| |
| target-module@4012c000 { |
| compatible = "ti,sysc-omap4", "ti,sysc"; |
| reg = <0x4012c000 0x4>, |
| <0x4012c010 0x4>; |
| reg-names = "rev", "sysc"; |
| ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| clocks = <&abe_clkctrl OMAP4_SLIMBUS1_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */ |
| <0x4902c000 0x4902c000 0x1000>; /* L3 */ |
| |
| /* No child device binding or driver in mainline */ |
| }; |
| |
| dmm@4e000000 { |
| compatible = "ti,omap4-dmm"; |
| reg = <0x4e000000 0x800>; |
| interrupts = <0 113 0x4>; |
| ti,hwmods = "dmm"; |
| }; |
| |
| emif1: emif@4c000000 { |
| compatible = "ti,emif-4d"; |
| reg = <0x4c000000 0x100>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "emif1"; |
| ti,no-idle-on-init; |
| phy-type = <1>; |
| hw-caps-read-idle-ctrl; |
| hw-caps-ll-interface; |
| hw-caps-temp-alert; |
| }; |
| |
| emif2: emif@4d000000 { |
| compatible = "ti,emif-4d"; |
| reg = <0x4d000000 0x100>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "emif2"; |
| ti,no-idle-on-init; |
| phy-type = <1>; |
| hw-caps-read-idle-ctrl; |
| hw-caps-ll-interface; |
| hw-caps-temp-alert; |
| }; |
| |
| aes1_target: target-module@4b501000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x4b501080 0x4>, |
| <0x4b501084 0x4>, |
| <0x4b501088 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| ti,syss-mask = <1>; |
| /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ |
| clocks = <&l4_secure_clkctrl OMAP4_AES1_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x4b501000 0x1000>; |
| |
| aes1: aes@0 { |
| compatible = "ti,omap4-aes"; |
| reg = <0 0xa0>; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 111>, <&sdma 110>; |
| dma-names = "tx", "rx"; |
| }; |
| }; |
| |
| aes2_target: target-module@4b701000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x4b701080 0x4>, |
| <0x4b701084 0x4>, |
| <0x4b701088 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| ti,syss-mask = <1>; |
| /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ |
| clocks = <&l4_secure_clkctrl OMAP4_AES2_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x4b701000 0x1000>; |
| |
| aes2: aes@0 { |
| compatible = "ti,omap4-aes"; |
| reg = <0 0xa0>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 114>, <&sdma 113>; |
| dma-names = "tx", "rx"; |
| }; |
| }; |
| |
| sham_target: target-module@4b100000 { |
| compatible = "ti,sysc-omap3-sham", "ti,sysc"; |
| reg = <0x4b100100 0x4>, |
| <0x4b100110 0x4>, |
| <0x4b100114 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,syss-mask = <1>; |
| /* Domains (P, C): l4per_pwrdm, l4_secure_clkdm */ |
| clocks = <&l4_secure_clkctrl OMAP4_SHA2MD5_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x4b100000 0x1000>; |
| |
| sham: sham@0 { |
| compatible = "ti,omap4-sham"; |
| reg = <0 0x300>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&sdma 119>; |
| dma-names = "rx"; |
| }; |
| }; |
| |
| abb_mpu: regulator-abb-mpu { |
| compatible = "ti,abb-v2"; |
| regulator-name = "abb_mpu"; |
| #address-cells = <0>; |
| #size-cells = <0>; |
| ti,tranxdone-status-mask = <0x80>; |
| clocks = <&sys_clkin_ck>; |
| ti,settling-time = <50>; |
| ti,clock-cycles = <16>; |
| |
| status = "disabled"; |
| }; |
| |
| abb_iva: regulator-abb-iva { |
| compatible = "ti,abb-v2"; |
| regulator-name = "abb_iva"; |
| #address-cells = <0>; |
| #size-cells = <0>; |
| ti,tranxdone-status-mask = <0x80000000>; |
| clocks = <&sys_clkin_ck>; |
| ti,settling-time = <50>; |
| ti,clock-cycles = <16>; |
| |
| status = "disabled"; |
| }; |
| |
| target-module@56000000 { |
| compatible = "ti,sysc-omap4", "ti,sysc"; |
| reg = <0x5600fe00 0x4>, |
| <0x5600fe10 0x4>; |
| reg-names = "rev", "sysc"; |
| ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>, |
| <SYSC_IDLE_SMART_WKUP>; |
| clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x56000000 0x2000000>; |
| |
| /* |
| * Closed source PowerVR driver, no child device |
| * binding or driver in mainline |
| */ |
| }; |
| |
| /* |
| * DSS is only using l3 mapping without l4 as noted in the TRM |
| * "10.1.3 DSS Register Manual" for omap4460. |
| */ |
| target-module@58000000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x58000000 4>, |
| <0x58000014 4>; |
| reg-names = "rev", "syss"; |
| ti,syss-mask = <1>; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 0>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>; |
| clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x58000000 0x1000000>; |
| |
| dss: dss@0 { |
| compatible = "ti,omap4-dss"; |
| reg = <0 0x80>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0x1000000>; |
| |
| target-module@1000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x1000 0x4>, |
| <0x1010 0x4>, |
| <0x1014 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-midle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| SYSC_OMAP2_ENAWAKEUP | |
| SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,syss-mask = <1>; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "fck", "sys_clk"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1000 0x1000>; |
| |
| dispc@0 { |
| compatible = "ti,omap4-dispc"; |
| reg = <0 0x1000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; |
| clock-names = "fck"; |
| }; |
| }; |
| |
| target-module@2000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x2000 0x4>, |
| <0x2010 0x4>, |
| <0x2014 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,syss-mask = <1>; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "fck", "sys_clk"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x2000 0x1000>; |
| |
| rfbi: encoder@0 { |
| reg = <0 0x1000>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, <&l3_div_ck>; |
| clock-names = "fck", "ick"; |
| }; |
| }; |
| |
| target-module@3000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x3000 0x4>; |
| reg-names = "rev"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "sys_clk"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x3000 0x1000>; |
| |
| venc: encoder@0 { |
| compatible = "ti,omap4-venc"; |
| reg = <0 0x1000>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 11>; |
| clock-names = "fck"; |
| }; |
| }; |
| |
| target-module@4000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x4000 0x4>, |
| <0x4010 0x4>, |
| <0x4014 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| SYSC_OMAP2_ENAWAKEUP | |
| SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,syss-mask = <1>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x4000 0x1000>; |
| |
| dsi1: encoder@0 { |
| compatible = "ti,omap4-dsi"; |
| reg = <0 0x200>, |
| <0x200 0x40>, |
| <0x300 0x20>; |
| reg-names = "proto", "phy", "pll"; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| }; |
| |
| target-module@5000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x5000 0x4>, |
| <0x5010 0x4>, |
| <0x5014 0x4>; |
| reg-names = "rev", "sysc", "syss"; |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>, |
| <SYSC_IDLE_SMART>; |
| ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY | |
| SYSC_OMAP2_ENAWAKEUP | |
| SYSC_OMAP2_SOFTRESET | |
| SYSC_OMAP2_AUTOIDLE)>; |
| ti,syss-mask = <1>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x5000 0x1000>; |
| |
| dsi2: encoder@0 { |
| compatible = "ti,omap4-dsi"; |
| reg = <0 0x200>, |
| <0x200 0x40>, |
| <0x300 0x20>; |
| reg-names = "proto", "phy", "pll"; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "fck", "sys_clk"; |
| }; |
| }; |
| |
| target-module@6000 { |
| compatible = "ti,sysc-omap4", "ti,sysc"; |
| reg = <0x6000 0x4>, |
| <0x6010 0x4>; |
| reg-names = "rev", "sysc"; |
| /* |
| * Has SYSC_IDLE_SMART and SYSC_IDLE_SMART_WKUP |
| * but HDMI audio will fail with them. |
| */ |
| ti,sysc-sidle = <SYSC_IDLE_FORCE>, |
| <SYSC_IDLE_NO>; |
| ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 8>; |
| clock-names = "fck", "dss_clk"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x6000 0x2000>; |
| |
| hdmi: encoder@0 { |
| compatible = "ti,omap4-hdmi"; |
| reg = <0 0x200>, |
| <0x200 0x100>, |
| <0x300 0x100>, |
| <0x400 0x1000>; |
| reg-names = "wp", "pll", "phy", "core"; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| clocks = <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 9>, |
| <&l3_dss_clkctrl OMAP4_DSS_CORE_CLKCTRL 10>; |
| clock-names = "fck", "sys_clk"; |
| dmas = <&sdma 76>; |
| dma-names = "audio_tx"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| #include "omap4-l4.dtsi" |
| #include "omap4-l4-abe.dtsi" |
| #include "omap44xx-clocks.dtsi" |
| |
| &prm { |
| prm_tesla: prm@400 { |
| compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; |
| reg = <0x400 0x100>; |
| #reset-cells = <1>; |
| }; |
| |
| prm_core: prm@700 { |
| compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; |
| reg = <0x700 0x100>; |
| #reset-cells = <1>; |
| }; |
| |
| prm_ivahd: prm@f00 { |
| compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; |
| reg = <0xf00 0x100>; |
| #reset-cells = <1>; |
| }; |
| |
| prm_device: prm@1b00 { |
| compatible = "ti,omap4-prm-inst", "ti,omap-prm-inst"; |
| reg = <0x1b00 0x40>; |
| #reset-cells = <1>; |
| }; |
| }; |