| menuconfig SPI |
| bool "SPI Support" |
| |
| if SPI |
| |
| config DM_SPI |
| bool "Enable Driver Model for SPI drivers" |
| depends on DM |
| help |
| Enable driver model for SPI. The SPI slave interface |
| (spi_setup_slave(), spi_xfer(), etc.) is then implemented by |
| the SPI uclass. Drivers provide methods to access the SPI |
| buses that they control. The uclass interface is defined in |
| include/spi.h. The existing spi_slave structure is attached |
| as 'parent data' to every slave on each bus. Slaves |
| typically use driver-private data instead of extending the |
| spi_slave structure. |
| |
| if DM_SPI |
| |
| config SPI_MEM |
| bool "SPI memory extension" |
| help |
| Enable this option if you want to enable the SPI memory extension. |
| This extension is meant to simplify interaction with SPI memories |
| by providing an high-level interface to send memory-like commands. |
| |
| config ALTERA_SPI |
| bool "Altera SPI driver" |
| help |
| Enable the Altera SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Altera |
| IP core. Please find details on the "Embedded Peripherals IP |
| User Guide" of Altera. |
| |
| config ATCSPI200_SPI |
| bool "Andestech ATCSPI200 SPI driver" |
| help |
| Enable the Andestech ATCSPI200 SPI driver. This driver can be |
| used to access the SPI flash on AE3XX and AE250 platforms embedding |
| this Andestech IP core. |
| |
| config ATH79_SPI |
| bool "Atheros SPI driver" |
| depends on ARCH_ATH79 |
| help |
| Enable the Atheros ar7xxx/ar9xxx SoC SPI driver, it was used |
| to access SPI NOR flash and other SPI peripherals. This driver |
| uses driver model and requires a device tree binding to operate. |
| please refer to doc/device-tree-bindings/spi/spi-ath79.txt. |
| |
| config ATMEL_SPI |
| bool "Atmel SPI driver" |
| default y if ARCH_AT91 |
| help |
| This enables driver for the Atmel SPI Controller, present on |
| many AT91 (ARM) chips. This driver can be used to access |
| the SPI Flash, such as AT25DF321. |
| |
| config BCM63XX_HSSPI |
| bool "BCM63XX HSSPI driver" |
| depends on ARCH_BMIPS |
| help |
| Enable the BCM6328 HSSPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Broadcom |
| SPI core. |
| |
| config BCM63XX_SPI |
| bool "BCM6348 SPI driver" |
| depends on ARCH_BMIPS |
| help |
| Enable the BCM6348/BCM6358 SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding these Broadcom |
| SPI cores. |
| |
| config BCMSTB_SPI |
| bool "BCMSTB SPI driver" |
| help |
| Enable the Broadcom set-top box SPI driver. This driver can |
| be used to access the SPI flash on platforms embedding this |
| Broadcom SPI core. |
| |
| config CADENCE_QSPI |
| bool "Cadence QSPI driver" |
| help |
| Enable the Cadence Quad-SPI (QSPI) driver. This driver can be |
| used to access the SPI NOR flash on platforms embedding this |
| Cadence IP core. |
| |
| config DESIGNWARE_SPI |
| bool "Designware SPI driver" |
| help |
| Enable the Designware SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Designware |
| IP core. |
| |
| config EXYNOS_SPI |
| bool "Samsung Exynos SPI driver" |
| help |
| Enable the Samsung Exynos SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Samsung |
| Exynos IP core. |
| |
| config FSL_DSPI |
| bool "Freescale DSPI driver" |
| help |
| Enable the Freescale DSPI driver. This driver can be used to |
| access the SPI NOR flash and SPI Data flash on platforms embedding |
| this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms |
| use this driver. |
| |
| config ICH_SPI |
| bool "Intel ICH SPI driver" |
| help |
| Enable the Intel ICH SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Intel |
| ICH IP core. |
| |
| config MVEBU_A3700_SPI |
| bool "Marvell Armada 3700 SPI driver" |
| select CLK_ARMADA_3720 |
| help |
| Enable the Marvell Armada 3700 SPI driver. This driver can be |
| used to access the SPI NOR flash on platforms embedding this |
| Marvell IP core. |
| |
| config PIC32_SPI |
| bool "Microchip PIC32 SPI driver" |
| depends on MACH_PIC32 |
| help |
| Enable the Microchip PIC32 SPI driver. This driver can be used |
| to access the SPI NOR flash, MMC-over-SPI on platforms based on |
| Microchip PIC32 family devices. |
| |
| config RENESAS_RPC_SPI |
| bool "Renesas RPC SPI driver" |
| depends on RCAR_GEN3 |
| help |
| Enable the Renesas RPC SPI driver, used to access SPI NOR flash |
| on Renesas RCar Gen3 SoCs. This uses driver model and requires a |
| device tree binding to operate. |
| |
| config ROCKCHIP_SPI |
| bool "Rockchip SPI driver" |
| help |
| Enable the Rockchip SPI driver, used to access SPI NOR flash and |
| other SPI peripherals (such as the Chrome OS EC) on Rockchip SoCs. |
| This uses driver model and requires a device tree binding to |
| operate. |
| |
| config SANDBOX_SPI |
| bool "Sandbox SPI driver" |
| depends on SANDBOX && DM |
| help |
| Enable SPI support for sandbox. This is an emulation of a real SPI |
| bus. Devices can be attached to the bus using the device tree |
| which specifies the driver to use. As an example, see this device |
| tree fragment from sandbox.dts. It shows that the SPI bus has a |
| single flash device on chip select 0 which is emulated by the driver |
| for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c. |
| |
| spi@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| compatible = "sandbox,spi"; |
| cs-gpios = <0>, <&gpio_a 0>; |
| flash@0 { |
| reg = <0>; |
| compatible = "spansion,m25p16", "sandbox,spi-flash"; |
| spi-max-frequency = <40000000>; |
| sandbox,filename = "spi.bin"; |
| }; |
| }; |
| |
| config STM32_QSPI |
| bool "STM32F7 QSPI driver" |
| depends on STM32F7 |
| help |
| Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be |
| used to access the SPI NOR flash chips on platforms embedding |
| this ST IP core. |
| |
| config SUN4I_SPI |
| bool "Allwinner A10 SoCs SPI controller" |
| help |
| SPI driver for Allwinner sun4i, sun5i and sun7i SoCs |
| |
| config TEGRA114_SPI |
| bool "nVidia Tegra114 SPI driver" |
| help |
| Enable the nVidia Tegra114 SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this nVidia Tegra114 |
| IP core. |
| |
| This controller is different than the older SoCs SPI controller and |
| also register interface get changed with this controller. |
| |
| config TEGRA20_SFLASH |
| bool "nVidia Tegra20 Serial Flash controller driver" |
| help |
| Enable the nVidia Tegra20 Serial Flash controller driver. This driver |
| can be used to access the SPI NOR flash on platforms embedding this |
| nVidia Tegra20 IP core. |
| |
| config TEGRA20_SLINK |
| bool "nVidia Tegra20/Tegra30 SLINK driver" |
| help |
| Enable the nVidia Tegra20/Tegra30 SLINK driver. This driver can |
| be used to access the SPI NOR flash on platforms embedding this |
| nVidia Tegra20/Tegra30 IP cores. |
| |
| config TEGRA210_QSPI |
| bool "nVidia Tegra210 QSPI driver" |
| help |
| Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver |
| be used to access SPI chips on platforms embedding this |
| NVIDIA Tegra210 IP core. |
| |
| config XILINX_SPI |
| bool "Xilinx SPI driver" |
| help |
| Enable the Xilinx SPI driver from the Xilinx EDK. This SPI |
| controller support 8 bit SPI transfers only, with or w/o FIFO. |
| For more info on Xilinx SPI Register Definitions and Overview |
| see driver file - drivers/spi/xilinx_spi.c |
| |
| config ZYNQ_SPI |
| bool "Zynq SPI driver" |
| depends on ARCH_ZYNQ || ARCH_ZYNQMP |
| help |
| Enable the Zynq SPI driver. This driver can be used to |
| access the SPI NOR flash on platforms embedding this Zynq |
| SPI IP core. |
| |
| config ZYNQ_QSPI |
| bool "Zynq QSPI driver" |
| depends on ARCH_ZYNQ |
| help |
| Enable the Zynq Quad-SPI (QSPI) driver. This driver can be |
| used to access the SPI NOR flash on platforms embedding this |
| Zynq QSPI IP core. This IP is used to connect the flash in |
| 4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel. |
| |
| config ZYNQMP_GQSPI |
| bool "Configure ZynqMP Generic QSPI" |
| depends on ARCH_ZYNQMP |
| help |
| This option is used to enable ZynqMP QSPI controller driver which |
| is used to communicate with qspi flash devices. |
| |
| endif # if DM_SPI |
| |
| config SOFT_SPI |
| bool "Soft SPI driver" |
| help |
| Enable Soft SPI driver. This driver is to use GPIO simulate |
| the SPI protocol. |
| |
| config CF_SPI |
| bool "ColdFire SPI driver" |
| help |
| Enable the ColdFire SPI driver. This driver can be used on |
| some m68k SoCs. |
| |
| config FSL_ESPI |
| bool "Freescale eSPI driver" |
| help |
| Enable the Freescale eSPI driver. This driver can be used to |
| access the SPI interface and SPI NOR flash on platforms embedding |
| this Freescale eSPI IP core. |
| |
| config FSL_QSPI |
| bool "Freescale QSPI driver" |
| help |
| Enable the Freescale Quad-SPI (QSPI) driver. This driver can be |
| used to access the SPI NOR flash on platforms embedding this |
| Freescale IP core. |
| |
| config DAVINCI_SPI |
| bool "Davinci & Keystone SPI driver" |
| depends on ARCH_DAVINCI || ARCH_KEYSTONE |
| help |
| Enable the Davinci SPI driver |
| |
| config SH_SPI |
| bool "SuperH SPI driver" |
| help |
| Enable the SuperH SPI controller driver. This driver can be used |
| on various SuperH SoCs, such as SH7757. |
| |
| config SH_QSPI |
| bool "Renesas Quad SPI driver" |
| help |
| Enable the Renesas Quad SPI controller driver. This driver can be |
| used on Renesas SoCs. |
| |
| config TI_QSPI |
| bool "TI QSPI driver" |
| help |
| Enable the TI Quad-SPI (QSPI) driver for DRA7xx and AM43xx evms. |
| This driver support spi flash single, quad and memory reads. |
| |
| config KIRKWOOD_SPI |
| bool "Marvell Kirkwood SPI Driver" |
| help |
| Enable support for SPI on various Marvell SoCs, such as |
| Kirkwood and Armada 375. |
| |
| config LPC32XX_SSP |
| bool "LPC32XX SPI Driver" |
| help |
| Enable support for SPI on LPC32xx |
| |
| config MPC8XX_SPI |
| bool "MPC8XX SPI Driver" |
| depends on MPC8xx |
| help |
| Enable support for SPI on MPC8XX |
| |
| config MPC8XXX_SPI |
| bool "MPC8XXX SPI Driver" |
| help |
| Enable support for SPI on the MPC8XXX PowerPC SoCs. |
| |
| config MXC_SPI |
| bool "MXC SPI Driver" |
| help |
| Enable the MXC SPI controller driver. This driver can be used |
| on various i.MX SoCs such as i.MX31/35/51/6/7. |
| |
| config MXS_SPI |
| bool "MXS SPI Driver" |
| help |
| Enable the MXS SPI controller driver. This driver can be used |
| on the i.MX23 and i.MX28 SoCs. |
| |
| config OMAP3_SPI |
| bool "McSPI driver for OMAP" |
| help |
| SPI master controller for OMAP24XX and later Multichannel SPI |
| (McSPI). This driver be used to access SPI chips on platforms |
| embedding this OMAP3 McSPI IP core. |
| |
| endif # menu "SPI Support" |