| /* |
| * (C) Copyright 2006-2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_ALPR 1 /* Board is ebony */ |
| #define CONFIG_440GX 1 /* Specifc GX support */ |
| #define CONFIG_440 1 /* ... PPC440 family */ |
| #define CONFIG_4xx 1 /* ... PPC4xx family */ |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| #define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ |
| #undef CFG_DRAM_TEST /* Disable-takes long time! */ |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ |
| #define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ |
| #define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ |
| #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ |
| #define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ |
| #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ |
| #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ |
| #define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ |
| #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 |
| #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 |
| #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 |
| |
| |
| #define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) |
| #define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & stack pointer (placed in internal SRAM) |
| *----------------------------------------------------------------------*/ |
| #define CFG_TEMP_STACK_OCM 1 |
| #define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE |
| #define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ |
| #define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ |
| #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) |
| #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR |
| |
| #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #undef CFG_EXT_SERIAL_CLOCK |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_UART1_CONSOLE /* define for uart1 as console */ |
| |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| /*----------------------------------------------------------------------- |
| * FLASH related |
| *----------------------------------------------------------------------*/ |
| #define CFG_FLASH_CFI 1 /* The flash is CFI compatible */ |
| #define CFG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ |
| |
| #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| |
| #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------*/ |
| #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ |
| #undef CONFIG_SDRAM_ECC /* enable ECC support */ |
| #define CFG_SDRAM_TABLE { \ |
| {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ |
| {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C EEPROM (PCF8594C) |
| *----------------------------------------------------------------------*/ |
| #define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ |
| #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CFG_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ |
| /* 8 byte page write mode using */ |
| /* last 3 bits of the address */ |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ |
| #define CFG_EEPROM_PAGE_WRITE_ENABLE |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \"run kernelx\" to boot the system;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth3\0" \ |
| "hostname=alpr\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath} ${init}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ |
| "mem=193M\0" \ |
| "flash_nfs=run nfsargs addip addtty;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip addtty;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ |
| "bootm\0" \ |
| "rootpath=/opt/projects/alpr/nfs_root\0" \ |
| "bootfile=/alpr/uImage\0" \ |
| "kernel_addr=fff00000\0" \ |
| "ramdisk_addr=fff10000\0" \ |
| "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ |
| "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ |
| "cp.b 100000 fffc0000 40000;" \ |
| "setenv filesize;saveenv\0" \ |
| "upd=run load;run update\0" \ |
| "ethprime=ppc_4xx_eth3\0" \ |
| "ethact=ppc_4xx_eth3\0" \ |
| "autoload=no\0" \ |
| "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ |
| "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ |
| "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ |
| "rootfstype=jffs2 init=/sbin/init\0" \ |
| "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ |
| ";bootm 200000\0" \ |
| "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ |
| "addtty;bootm 200000\0" \ |
| "kernel1=setenv actkernel 'kernel1';run load_fpga " \ |
| "kernel1_mtd\0" \ |
| "kernel2=setenv actkernel 'kernel2';run load_fpga " \ |
| "kernel2_mtd\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run kernel2" |
| |
| #define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ |
| #define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ |
| #define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ |
| #define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_HAS_ETH3 |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ |
| |
| #define CONFIG_NETCONSOLE /* include NetConsole support */ |
| |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ |
| CFG_CMD_ASKENV | \ |
| CFG_CMD_DHCP | \ |
| CFG_CMD_DIAG | \ |
| CFG_CMD_EEPROM | \ |
| CFG_CMD_ELF | \ |
| CFG_CMD_I2C | \ |
| CFG_CMD_IRQ | \ |
| CFG_CMD_MII | \ |
| CFG_CMD_NET | \ |
| CFG_CMD_NFS | \ |
| CFG_CMD_PCI | \ |
| CFG_CMD_PING | \ |
| CFG_CMD_FPGA | \ |
| CFG_CMD_NAND | \ |
| CFG_CMD_REGINFO) |
| |
| /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ |
| #include <cmd_confdefs.h> |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_ALT_MEMTEST 1 /* Enable more extensive memtest*/ |
| #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_LOOPW 1 /* enable loopw command */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| #define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| /* General PCI */ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ |
| #define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ |
| |
| /* Board-specific PCI */ |
| #define CFG_PCI_TARGET_INIT /* let board init pci target */ |
| #define CFG_PCI_MASTER_INIT |
| |
| #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ |
| #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ |
| |
| /*----------------------------------------------------------------------- |
| * FPGA stuff |
| *-----------------------------------------------------------------------*/ |
| #define CONFIG_FPGA CFG_ALTERA_CYCLON2 |
| #define CFG_FPGA_CHECK_CTRLC |
| #define CFG_FPGA_PROG_FEEDBACK |
| #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in |
| Reihe geschaltet -> sollte gehen, |
| aufpassen mit Datasize ist jetzt |
| halt doppelt so gross ... Seite 306 |
| ist das mit den multiple Device in PS |
| Mode erklaert ...*/ |
| |
| /* FPGA program pin configuration */ |
| #define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ |
| #define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */ |
| #define CFG_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ |
| #define CFG_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ |
| #define CFG_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ |
| |
| #define CFG_GPIO_SEL_DPR 14 /* cpu output */ |
| #define CFG_GPIO_SEL_AVR 15 /* cpu output */ |
| #define CFG_GPIO_PROG_EN 23 /* cpu output */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for GPIO setup |
| *-----------------------------------------------------------------------*/ |
| #define CFG_GPIO_SHUTDOWN (0x80000000 >> 6) |
| #define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9) |
| #define CFG_GPIO_EREADY (0x80000000 >> 26) |
| #define CFG_GPIO_REV0 (0x80000000 >> 14) |
| #define CFG_GPIO_REV1 (0x80000000 >> 15) |
| |
| /*----------------------------------------------------------------------- |
| * NAND-FLASH stuff |
| *-----------------------------------------------------------------------*/ |
| #define CFG_MAX_NAND_DEVICE 4 |
| #define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE |
| #define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ |
| #define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \ |
| CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 } |
| #define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| *----------------------------------------------------------------------*/ |
| #define CFG_FLASH CFG_FLASH_BASE |
| |
| /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ |
| #define CFG_EBC_PB0AP 0x92015480 |
| #define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ |
| |
| /* Memory Bank 1 (NAND-FLASH) initialization */ |
| #define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ |
| #define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ |
| #define CFG_CACHELINE_SIZE 32 /* ... */ |
| #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| #endif /* __CONFIG_H */ |