| /* |
| * (C) Copyright 2006-2008 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * (C) Copyright 2006 |
| * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com |
| * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * sequoia.h - configuration for Sequoia & Rainier boards |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| /* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */ |
| #ifndef CONFIG_RAINIER |
| #define CONFIG_440EPX 1 /* Specific PPC440EPx */ |
| #define CONFIG_HOSTNAME sequoia |
| #else |
| #define CONFIG_440GRX 1 /* Specific PPC440GRx */ |
| #define CONFIG_HOSTNAME rainier |
| #endif |
| #define CONFIG_440 1 /* ... PPC440 family */ |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFF80000 |
| #endif |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #include "amcc-common.h" |
| |
| /* Detect Sequoia PLL input clock automatically via CPLD bit */ |
| #define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_BCSR_BASE + 3) & 0x80) ? \ |
| 33333333 : 33000000) |
| |
| /* |
| * Define this if you want support for video console with radeon 9200 pci card |
| * Also set CONFIG_SYS_TEXT_BASE to 0xFFF80000 in board/amcc/sequoia/config.mk in this case |
| */ |
| |
| #ifdef CONFIG_VIDEO |
| /* |
| * 44x dcache supported is working now on sequoia, but we don't enable |
| * it yet since it needs further testing |
| */ |
| #define CONFIG_4xx_DCACHE /* enable dcache */ |
| #endif |
| |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the actual |
| * resources get mapped (not physical addresses). |
| */ |
| #define CONFIG_SYS_TLB_FOR_BOOT_FLASH 0x0003 |
| #define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 |
| #define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ |
| #define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */ |
| #define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ |
| #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE |
| #define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ |
| #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ |
| #define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 |
| #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 |
| #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 |
| |
| #define CONFIG_SYS_USB2D0_BASE 0xe0000100 |
| #define CONFIG_SYS_USB_DEVICE 0xe0000000 |
| #define CONFIG_SYS_USB_HOST 0xe0000400 |
| #define CONFIG_SYS_BCSR_BASE 0xc0000000 |
| |
| /* |
| * Initial RAM & stack pointer |
| */ |
| /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ |
| |
| /* |
| * Environment |
| */ |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_ENV_IS_NOWHERE /* Store env in memory only */ |
| #define CONFIG_ENV_SIZE (8 << 10) |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environ vars */ |
| #endif |
| |
| #if defined(CONFIG_CMD_FLASH) |
| /* |
| * FLASH related |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ |
| #endif /* CONFIG_CMD_FLASH */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif |
| |
| /* |
| * DDR SDRAM |
| */ |
| #define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ |
| #if !defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ |
| #endif |
| #define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ |
| /* 440EPx errata CHIP 11 */ |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| |
| /* I2C bootstrap EEPROM */ |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52 |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 |
| #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 |
| |
| /* I2C SYSMON (LM75, AD7414 is almost compatible) */ |
| #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ |
| #define CONFIG_DTT_AD7414 1 /* use AD7414 */ |
| #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ |
| #define CONFIG_SYS_DTT_MAX_TEMP 70 |
| #define CONFIG_SYS_DTT_LOW_TEMP -30 |
| #define CONFIG_SYS_DTT_HYSTERESIS 3 |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_PPC_OLD \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=FC000000\0" \ |
| "ramdisk_addr=FC180000\0" \ |
| "" |
| |
| #define CONFIG_M88E1111_PHY 1 |
| #define CONFIG_IBM_EMAC4_V4 1 |
| #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ |
| |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ |
| #define CONFIG_PHY1_ADDR 1 |
| |
| /* USB */ |
| #ifdef CONFIG_440EPX |
| #ifdef CONFIG_USB_EHCI_HCD |
| #define CONFIG_USB_EHCI_PPC4XX |
| #define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_EHCI_MMIO_BIG_ENDIAN |
| #define CONFIG_EHCI_DESC_BIG_ENDIAN |
| #else /* CONFIG_USB_EHCI_HCD */ |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_SYS_OHCI_BE_CONTROLLER |
| |
| #undef CONFIG_SYS_USB_OHCI_BOARD_INIT |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 |
| #endif |
| |
| /* Comment this out to enable USB 1.1 device */ |
| #define USB_2_0_DEVICE |
| |
| #endif /* CONFIG_440EPX */ |
| |
| /* Partitions */ |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_DTT |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_SDRAM |
| |
| #ifdef CONFIG_440EPX |
| #endif |
| |
| #ifndef CONFIG_RAINIER |
| #define CONFIG_SYS_POST_FPU_ON CONFIG_SYS_POST_FPU |
| #else |
| #define CONFIG_SYS_POST_FPU_ON 0 |
| #endif |
| |
| /* |
| * Don't run the memory POST on the NAND-booting version. It will |
| * overwrite part of the U-Boot image which is already loaded from NAND |
| * to SDRAM. |
| */ |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_SYS_POST_MEMORY_ON 0 |
| #else |
| #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY |
| #endif |
| |
| /* POST support */ |
| #define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ |
| CONFIG_SYS_POST_CPU | \ |
| CONFIG_SYS_POST_ETHER | \ |
| CONFIG_SYS_POST_FPU_ON | \ |
| CONFIG_SYS_POST_I2C | \ |
| CONFIG_SYS_POST_MEMORY_ON | \ |
| CONFIG_SYS_POST_SPR | \ |
| CONFIG_SYS_POST_UART) |
| |
| #define CONFIG_LOGBUFFER |
| #define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| /* |
| * PCI stuff |
| */ |
| /* General PCI */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ |
| /* CONFIG_SYS_PCI_MEMBASE */ |
| /* Board-specific PCI */ |
| #define CONFIG_SYS_PCI_TARGET_INIT |
| #define CONFIG_SYS_PCI_MASTER_INIT |
| #define CONFIG_SYS_PCI_BOARD_FIXUP_IRQ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ |
| #define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* |
| * On Sequoia CS0 and CS3 are switched when configuring for NAND booting |
| */ |
| #if !defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */ |
| /* Memory Bank 0 (NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x03017200 |
| #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) |
| |
| /* Memory Bank 3 (NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x018003c0 |
| #define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1c000) |
| #else |
| #define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ |
| /* Memory Bank 3 (NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x03017200 |
| #define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH_BASE | 0xda000) |
| |
| /* Memory Bank 0 (NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x018003c0 |
| #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) |
| #endif |
| |
| /* Memory Bank 2 (CPLD) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x24814580 |
| #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x38000) |
| |
| #define CONFIG_SYS_BCSR5_PCI66EN 0x80 |
| |
| /* |
| * NAND FLASH |
| */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) |
| #define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ |
| |
| /* |
| * PPC440 GPIO Configuration |
| */ |
| /* test-only: take GPIO init from pcs440ep ???? in config file */ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO14 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO28 USB2D_TXVALID */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ |
| }, \ |
| { \ |
| /* GPIO Core 1 */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_8PIN_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_CTS_N EBC_DATA(0) UART3_SIN*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_8PIN_DTR_N UART1_SOUT */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_8PIN_RI_N UART1_SIN */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ |
| } \ |
| } |
| |
| #ifdef CONFIG_VIDEO |
| #define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */ |
| #define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */ |
| #define VIDEO_IO_OFFSET 0xe8000000 |
| #define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET |
| #define CONFIG_VIDEO_LOGO |
| #define CONFIG_SPLASH_SCREEN |
| #endif |
| |
| #endif /* __CONFIG_H */ |