blob: 4f90b1b51d91b27a03528b2fb343d4a1508a3cd8 [file] [log] [blame]
/*
* (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
*
* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/************************************************************************
* 1 March 2004 Travis B. Sawyer <tsawyer@sandburst.com>
* Adapted to current Das U-Boot source
***********************************************************************/
/************************************************************************
* OCOTEA.h - configuration for IBM 440GX Ref (Ocotea)
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
#define CONFIG_OCOTEA 1 /* Board is ebony */
#define CONFIG_440_GX 1 /* Specifc GX support */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* Disable-takes long time! */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000)
#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
#define CFG_TEMP_STACK_OCM 1
#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*
* Define here the location of the environment variables (FLASH or NVRAM).
* Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
* supported for backward compatibility.
*/
#if 1
#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
/*-----------------------------------------------------------------------
* NVRAM/RTC
*
* NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
* The DS1743 code assumes this condition (i.e. -- it assumes the base
* address for the RTC registers is:
*
* CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
*
*----------------------------------------------------------------------*/
#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */
#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */
#ifdef CFG_ENV_IS_IN_NVRAM
#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)
#endif /* CFG_ENV_IS_IN_NVRAM */
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_FLASH_ADDR0 0x5555
#define CFG_FLASH_ADDR1 0x2aaa
#define CFG_FLASH_WORD_SIZE unsigned char
#ifdef CFG_ENV_IS_IN_FLASH
#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif /* CFG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
#define SPD_EEPROM_ADDRESS {0x53,0x52} /* SPD i2c spd addresses */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=ocotea\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$(serverip):$(rootpath)\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs $(bootargs) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
":$(hostname):$(netdev):off panic=1\0" \
"addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm $(kernel_addr)\0" \
"flash_self=run ramargs addip addtty;" \
"bootm $(kernel_addr) $(ramdisk_addr)\0" \
"net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/ocotea/uImage\0" \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
"load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \
"setenv filesize;saveenv\0" \
"upd=run load;run update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 2
#define CONFIG_PHY2_ADDR 0x10
#define CONFIG_PHY3_ADDR 0x18
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_DIAG | \
CFG_CMD_ELF | \
CFG_CMD_I2C | \
CFG_CMD_IRQ | \
CFG_CMD_MII | \
CFG_CMD_NET | \
CFG_CMD_NFS | \
CFG_CMD_PCI | \
CFG_CMD_PING | \
CFG_CMD_REGINFO | \
CFG_CMD_SDRAM | \
CFG_CMD_SNTP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CFG_HZ 100 /* decrementer freq: 1 ms ticks */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
/* Board-specific PCI */
#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
#define CFG_PCI_TARGET_INIT /* let board init pci target */
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#endif /* __CONFIG_H */