| /* |
| * U-boot - Configuration file for BF561 EZKIT board |
| */ |
| |
| #ifndef __CONFIG_EZKIT561_H__ |
| #define __CONFIG_EZKIT561_H__ |
| |
| #include <asm/blackfin-config-pre.h> |
| |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMDLINE_EDITING 1 |
| #define CONFIG_BAUDRATE 57600 |
| /* Set default serial console for bf537 */ |
| #define CONFIG_UART_CONSOLE 0 |
| #define CONFIG_EZKIT561 1 |
| #define CONFIG_BOOTDELAY 5 |
| |
| #define CONFIG_PANIC_HANG 1 |
| |
| #define CONFIG_BFIN_CPU bf561-0.3 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS |
| |
| /* This sets the default state of the cache on U-Boot's boot */ |
| #define CONFIG_ICACHE_ON |
| #define CONFIG_DCACHE_ON |
| |
| /* |
| * Board settings |
| */ |
| #define CONFIG_DRIVER_SMC91111 1 |
| #define CONFIG_SMC91111_BASE 0x2C010300 |
| #define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024) |
| #define CONFIG_SMC_USE_32_BIT 1 |
| #define CONFIG_MISC_INIT_R 1 |
| |
| /* |
| * Clock settings |
| */ |
| |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 30000000 |
| /* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ |
| /* 1=CLKIN/2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ |
| /* 1=bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* CONFIG_VCO_MULT controls what the multiplier of the PLL is */ |
| /* Values can range from 1-64 */ |
| #define CONFIG_VCO_MULT 20 |
| /* CONFIG_CCLK_DIV controls what the core clock divider is */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 5 |
| /* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ |
| /* Values can range from 2-65535 */ |
| /* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ |
| #define CONFIG_SPI_BAUD 2 |
| #define CONFIG_SPI_BAUD_INITBLOCK 4 |
| |
| /* |
| * Network settings |
| */ |
| #if (CONFIG_DRIVER_SMC91111) |
| #define CONFIG_IPADDR 192.168.0.15 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_GATEWAYIP 192.168.0.1 |
| #define CONFIG_SERVERIP 192.168.0.2 |
| #define CONFIG_HOSTNAME ezkit561 |
| #define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs |
| #endif /* CONFIG_DRIVER_SMC91111 */ |
| |
| /* |
| * Flash settings |
| */ |
| |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| #define CONFIG_SYS_FLASH_CFI_AMD_RESET |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_SYS_FLASH_BASE 0x20000000 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */ |
| #define CONFIG_ENV_ADDR 0x20020000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ |
| /* JFFS Partition offset set */ |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 |
| /* 512k reserved for u-boot */ |
| #define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 |
| |
| /* |
| * SDRAM settings & memory map |
| */ |
| |
| #define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ |
| #define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ |
| #define CONFIG_MEM_MT48LC16M16A2TG_75 1 |
| |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */ |
| |
| #define CONFIG_LOADADDR 0x01000000 /* default load address */ |
| #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN) |
| |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN) |
| |
| #define CONFIG_SYS_GBL_DATA_SIZE 0x4000 |
| #define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4) |
| #define CONFIG_STACKSIZE (128*1024) /* regular stack */ |
| |
| #if ( CONFIG_CLKIN_HALF == 0 ) |
| #define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) |
| #else |
| #define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) |
| #endif |
| |
| #if (CONFIG_PLL_BYPASS == 0) |
| #define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) |
| #define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) |
| #else |
| #define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ |
| #define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ |
| #endif |
| |
| /* |
| * Command settings |
| */ |
| |
| #define CONFIG_SYS_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */ |
| /* only perform a configuration */ |
| /* lookup from the BOOTP/DHCP server */ |
| /* but not try to load any image */ |
| /* using TFTP */ |
| #define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */ |
| /* currently its disabled */ |
| #define CONFIG_BOOTCOMMAND "run ramboot" |
| #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" |
| |
| #if (CONFIG_DRIVER_SMC91111) |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ |
| "$(rootpath) console=ttyBF0,57600\0" \ |
| "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ |
| "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ |
| "ramboot=tftpboot $(loadaddr) linux; " \ |
| "run ramargs; run addip; bootelf\0" \ |
| "nfsboot=tftpboot $(loadaddr) linux; " \ |
| "run nfsargs; run addip; bootelf\0" \ |
| "update=tftpboot $(loadaddr) u-boot.bin; " \ |
| "protect off 0x20000000 0x2003FFFF; " \ |
| "erase 0x20000000 0x2003FFFF; " \ |
| "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ |
| "" |
| #else |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ |
| "flashboot=bootm 0x20100000\0" \ |
| "" |
| #endif |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_JFFS2 |
| |
| #if defined(CONFIG_DRIVER_SMC91111) |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #endif |
| |
| /* |
| * Console settings |
| */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| #define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_LOADS_ECHO 1 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */ |
| #define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ |
| |
| /* |
| * FLASH organization and environment definitions |
| */ |
| #define CONFIG_EBIU_SDRRC_VAL 0x306 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x91114d |
| #define CONFIG_EBIU_SDBCTL_VAL 0x15 |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0x3F |
| #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 |
| |
| #include <asm/blackfin-config-post.h> |
| |
| #endif /* __CONFIG_EZKIT561_H__ */ |