blob: 8bbb1aef2ee226aeff98feda073d1558ff55612b [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
#include <dt-bindings/reset/stm32mp1-resets.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
clock-frequency = <650000000>;
device_type = "cpu";
reg = <0>;
operating-points-v2 = <&cpu0_opp_table>;
nvmem-cells = <&part_number_otp>;
nvmem-cell-names = "part_number";
};
};
cpu0_opp_table: cpu0-opp-table {
compatible = "operating-points-v2";
opp-shared;
opp-650000000 {
opp-hz = /bits/ 64 <650000000>;
opp-microvolt = <1200000>;
opp-supported-hw = <0x1>;
};
opp-800000000 {
opp-hz = /bits/ 64 <800000000>;
opp-microvolt = <1350000>;
opp-supported-hw = <0x2>;
};
};
arm-pmu {
compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>;
interrupt-parent = <&intc>;
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
};
intc: interrupt-controller@a0021000 {
compatible = "arm,cortex-a7-gic";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0xa0021000 0x1000>,
<0xa0022000 0x2000>;
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&intc>;
};
clocks {
clk_hse: clk-hse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
};
clk_lse: clk-lse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
};
clk_lsi: clk-lsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32000>;
};
clk_csi: clk-csi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <4000000>;
};
};
thermal-zones {
cpu_thermal: cpu-thermal {
polling-delay-passive = <0>;
polling-delay = <0>;
thermal-sensors = <&dts>;
trips {
cpu_alert1: cpu-alert1 {
temperature = <85000>;
hysteresis = <0>;
type = "passive";
};
cpu-crit {
temperature = <120000>;
hysteresis = <0>;
type = "critical";
};
};
cooling-maps {
};
};
};
booster: regulator-booster {
compatible = "st,stm32mp1-booster";
st,syscfg = <&syscfg>;
status = "disabled";
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
ranges;
timers2: timer@40000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40000000 0x400>;
clocks = <&rcc TIM2_K>;
clock-names = "int";
dmas = <&dmamux1 18 0x400 0x1>,
<&dmamux1 19 0x400 0x1>,
<&dmamux1 20 0x400 0x1>,
<&dmamux1 21 0x400 0x1>,
<&dmamux1 22 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4", "up";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@1 {
compatible = "st,stm32h7-timer-trigger";
reg = <1>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
timers3: timer@40001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40001000 0x400>;
clocks = <&rcc TIM3_K>;
clock-names = "int";
dmas = <&dmamux1 23 0x400 0x1>,
<&dmamux1 24 0x400 0x1>,
<&dmamux1 25 0x400 0x1>,
<&dmamux1 26 0x400 0x1>,
<&dmamux1 27 0x400 0x1>,
<&dmamux1 28 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@2 {
compatible = "st,stm32h7-timer-trigger";
reg = <2>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
timers4: timer@40002000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40002000 0x400>;
clocks = <&rcc TIM4_K>;
clock-names = "int";
dmas = <&dmamux1 29 0x400 0x1>,
<&dmamux1 30 0x400 0x1>,
<&dmamux1 31 0x400 0x1>,
<&dmamux1 32 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@3 {
compatible = "st,stm32h7-timer-trigger";
reg = <3>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
timers5: timer@40003000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40003000 0x400>;
clocks = <&rcc TIM5_K>;
clock-names = "int";
dmas = <&dmamux1 55 0x400 0x1>,
<&dmamux1 56 0x400 0x1>,
<&dmamux1 57 0x400 0x1>,
<&dmamux1 58 0x400 0x1>,
<&dmamux1 59 0x400 0x1>,
<&dmamux1 60 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@4 {
compatible = "st,stm32h7-timer-trigger";
reg = <4>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
timers6: timer@40004000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40004000 0x400>;
clocks = <&rcc TIM6_K>;
clock-names = "int";
dmas = <&dmamux1 69 0x400 0x1>;
dma-names = "up";
status = "disabled";
timer@5 {
compatible = "st,stm32h7-timer-trigger";
reg = <5>;
status = "disabled";
};
};
timers7: timer@40005000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40005000 0x400>;
clocks = <&rcc TIM7_K>;
clock-names = "int";
dmas = <&dmamux1 70 0x400 0x1>;
dma-names = "up";
status = "disabled";
timer@6 {
compatible = "st,stm32h7-timer-trigger";
reg = <6>;
status = "disabled";
};
};
timers12: timer@40006000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40006000 0x400>;
clocks = <&rcc TIM12_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@11 {
compatible = "st,stm32h7-timer-trigger";
reg = <11>;
status = "disabled";
};
};
timers13: timer@40007000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40007000 0x400>;
clocks = <&rcc TIM13_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@12 {
compatible = "st,stm32h7-timer-trigger";
reg = <12>;
status = "disabled";
};
};
timers14: timer@40008000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40008000 0x400>;
clocks = <&rcc TIM14_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@13 {
compatible = "st,stm32h7-timer-trigger";
reg = <13>;
status = "disabled";
};
};
lptimer1: timer@40009000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x40009000 0x400>;
interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LPTIM1_K>;
clock-names = "mux";
wakeup-source;
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@0 {
compatible = "st,stm32-lptimer-trigger";
reg = <0>;
status = "disabled";
};
counter {
compatible = "st,stm32-lptimer-counter";
status = "disabled";
};
};
spi2: spi@4000b000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x4000b000 0x400>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI2_K>;
resets = <&rcc SPI2_R>;
dmas = <&dmamux1 39 0x400 0x05>,
<&dmamux1 40 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
i2s2: audio-controller@4000b000 {
compatible = "st,stm32h7-i2s";
#sound-dai-cells = <0>;
reg = <0x4000b000 0x400>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 39 0x400 0x01>,
<&dmamux1 40 0x400 0x01>;
dma-names = "rx", "tx";
status = "disabled";
};
spi3: spi@4000c000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x4000c000 0x400>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI3_K>;
resets = <&rcc SPI3_R>;
dmas = <&dmamux1 61 0x400 0x05>,
<&dmamux1 62 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
i2s3: audio-controller@4000c000 {
compatible = "st,stm32h7-i2s";
#sound-dai-cells = <0>;
reg = <0x4000c000 0x400>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 61 0x400 0x01>,
<&dmamux1 62 0x400 0x01>;
dma-names = "rx", "tx";
status = "disabled";
};
spdifrx: audio-controller@4000d000 {
compatible = "st,stm32h7-spdifrx";
#sound-dai-cells = <0>;
reg = <0x4000d000 0x400>;
clocks = <&rcc SPDIF_K>;
clock-names = "kclk";
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 93 0x400 0x01>,
<&dmamux1 94 0x400 0x01>;
dma-names = "rx", "rx-ctrl";
status = "disabled";
};
usart2: serial@4000e000 {
compatible = "st,stm32h7-uart";
reg = <0x4000e000 0x400>;
interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART2_K>;
wakeup-source;
dmas = <&dmamux1 43 0x400 0x15>,
<&dmamux1 44 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
usart3: serial@4000f000 {
compatible = "st,stm32h7-uart";
reg = <0x4000f000 0x400>;
interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART3_K>;
wakeup-source;
dmas = <&dmamux1 45 0x400 0x15>,
<&dmamux1 46 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
uart4: serial@40010000 {
compatible = "st,stm32h7-uart";
reg = <0x40010000 0x400>;
interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART4_K>;
wakeup-source;
dmas = <&dmamux1 63 0x400 0x15>,
<&dmamux1 64 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
uart5: serial@40011000 {
compatible = "st,stm32h7-uart";
reg = <0x40011000 0x400>;
interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART5_K>;
wakeup-source;
dmas = <&dmamux1 65 0x400 0x15>,
<&dmamux1 66 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
i2c1: i2c@40012000 {
compatible = "st,stm32mp15-i2c";
reg = <0x40012000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C1_K>;
resets = <&rcc I2C1_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x1>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
i2c2: i2c@40013000 {
compatible = "st,stm32mp15-i2c";
reg = <0x40013000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C2_K>;
resets = <&rcc I2C2_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x2>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
i2c3: i2c@40014000 {
compatible = "st,stm32mp15-i2c";
reg = <0x40014000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C3_K>;
resets = <&rcc I2C3_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x4>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
i2c5: i2c@40015000 {
compatible = "st,stm32mp15-i2c";
reg = <0x40015000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C5_K>;
resets = <&rcc I2C5_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x10>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
cec: cec@40016000 {
compatible = "st,stm32-cec";
reg = <0x40016000 0x400>;
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc CEC_K>, <&rcc CEC>;
clock-names = "cec", "hdmi-cec";
status = "disabled";
};
dac: dac@40017000 {
compatible = "st,stm32h7-dac-core";
reg = <0x40017000 0x400>;
clocks = <&rcc DAC12>;
clock-names = "pclk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dac1: dac@1 {
compatible = "st,stm32-dac";
#io-channel-cells = <1>;
reg = <1>;
status = "disabled";
};
dac2: dac@2 {
compatible = "st,stm32-dac";
#io-channel-cells = <1>;
reg = <2>;
status = "disabled";
};
};
uart7: serial@40018000 {
compatible = "st,stm32h7-uart";
reg = <0x40018000 0x400>;
interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART7_K>;
wakeup-source;
dmas = <&dmamux1 79 0x400 0x15>,
<&dmamux1 80 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
uart8: serial@40019000 {
compatible = "st,stm32h7-uart";
reg = <0x40019000 0x400>;
interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART8_K>;
wakeup-source;
dmas = <&dmamux1 81 0x400 0x15>,
<&dmamux1 82 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
timers1: timer@44000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44000000 0x400>;
clocks = <&rcc TIM1_K>;
clock-names = "int";
dmas = <&dmamux1 11 0x400 0x1>,
<&dmamux1 12 0x400 0x1>,
<&dmamux1 13 0x400 0x1>,
<&dmamux1 14 0x400 0x1>,
<&dmamux1 15 0x400 0x1>,
<&dmamux1 16 0x400 0x1>,
<&dmamux1 17 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4",
"up", "trig", "com";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@0 {
compatible = "st,stm32h7-timer-trigger";
reg = <0>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
timers8: timer@44001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44001000 0x400>;
clocks = <&rcc TIM8_K>;
clock-names = "int";
dmas = <&dmamux1 47 0x400 0x1>,
<&dmamux1 48 0x400 0x1>,
<&dmamux1 49 0x400 0x1>,
<&dmamux1 50 0x400 0x1>,
<&dmamux1 51 0x400 0x1>,
<&dmamux1 52 0x400 0x1>,
<&dmamux1 53 0x400 0x1>;
dma-names = "ch1", "ch2", "ch3", "ch4",
"up", "trig", "com";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@7 {
compatible = "st,stm32h7-timer-trigger";
reg = <7>;
status = "disabled";
};
counter {
compatible = "st,stm32-timer-counter";
status = "disabled";
};
};
usart6: serial@44003000 {
compatible = "st,stm32h7-uart";
reg = <0x44003000 0x400>;
interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART6_K>;
wakeup-source;
dmas = <&dmamux1 71 0x400 0x15>,
<&dmamux1 72 0x400 0x11>;
dma-names = "rx", "tx";
status = "disabled";
};
spi1: spi@44004000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44004000 0x400>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI1_K>;
resets = <&rcc SPI1_R>;
dmas = <&dmamux1 37 0x400 0x05>,
<&dmamux1 38 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
i2s1: audio-controller@44004000 {
compatible = "st,stm32h7-i2s";
#sound-dai-cells = <0>;
reg = <0x44004000 0x400>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 37 0x400 0x01>,
<&dmamux1 38 0x400 0x01>;
dma-names = "rx", "tx";
status = "disabled";
};
spi4: spi@44005000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44005000 0x400>;
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI4_K>;
resets = <&rcc SPI4_R>;
dmas = <&dmamux1 83 0x400 0x05>,
<&dmamux1 84 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
timers15: timer@44006000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44006000 0x400>;
clocks = <&rcc TIM15_K>;
clock-names = "int";
dmas = <&dmamux1 105 0x400 0x1>,
<&dmamux1 106 0x400 0x1>,
<&dmamux1 107 0x400 0x1>,
<&dmamux1 108 0x400 0x1>;
dma-names = "ch1", "up", "trig", "com";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@14 {
compatible = "st,stm32h7-timer-trigger";
reg = <14>;
status = "disabled";
};
};
timers16: timer@44007000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44007000 0x400>;
clocks = <&rcc TIM16_K>;
clock-names = "int";
dmas = <&dmamux1 109 0x400 0x1>,
<&dmamux1 110 0x400 0x1>;
dma-names = "ch1", "up";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@15 {
compatible = "st,stm32h7-timer-trigger";
reg = <15>;
status = "disabled";
};
};
timers17: timer@44008000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44008000 0x400>;
clocks = <&rcc TIM17_K>;
clock-names = "int";
dmas = <&dmamux1 111 0x400 0x1>,
<&dmamux1 112 0x400 0x1>;
dma-names = "ch1", "up";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
#pwm-cells = <3>;
status = "disabled";
};
timer@16 {
compatible = "st,stm32h7-timer-trigger";
reg = <16>;
status = "disabled";
};
};
spi5: spi@44009000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44009000 0x400>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI5_K>;
resets = <&rcc SPI5_R>;
dmas = <&dmamux1 85 0x400 0x05>,
<&dmamux1 86 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
sai1: sai@4400a000 {
compatible = "st,stm32h7-sai";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x4400a000 0x400>;
reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
resets = <&rcc SAI1_R>;
status = "disabled";
sai1a: audio-controller@4400a004 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-a";
reg = <0x4 0x20>;
clocks = <&rcc SAI1_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 87 0x400 0x01>;
status = "disabled";
};
sai1b: audio-controller@4400a024 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-b";
reg = <0x24 0x20>;
clocks = <&rcc SAI1_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 88 0x400 0x01>;
status = "disabled";
};
};
sai2: sai@4400b000 {
compatible = "st,stm32h7-sai";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x4400b000 0x400>;
reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
resets = <&rcc SAI2_R>;
status = "disabled";
sai2a: audio-controller@4400b004 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-a";
reg = <0x4 0x20>;
clocks = <&rcc SAI2_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 89 0x400 0x01>;
status = "disabled";
};
sai2b: audio-controller@4400b024 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-b";
reg = <0x24 0x20>;
clocks = <&rcc SAI2_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 90 0x400 0x01>;
status = "disabled";
};
};
sai3: sai@4400c000 {
compatible = "st,stm32h7-sai";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x4400c000 0x400>;
reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
resets = <&rcc SAI3_R>;
status = "disabled";
sai3a: audio-controller@4400c004 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-a";
reg = <0x04 0x20>;
clocks = <&rcc SAI3_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 113 0x400 0x01>;
status = "disabled";
};
sai3b: audio-controller@4400c024 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-b";
reg = <0x24 0x20>;
clocks = <&rcc SAI3_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 114 0x400 0x01>;
status = "disabled";
};
};
dfsdm: dfsdm@4400d000 {
compatible = "st,stm32mp1-dfsdm";
reg = <0x4400d000 0x800>;
clocks = <&rcc DFSDM_K>;
clock-names = "dfsdm";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dfsdm0: filter@0 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <0>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 101 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm1: filter@1 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <1>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 102 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm2: filter@2 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <2>;
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 103 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm3: filter@3 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <3>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 104 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm4: filter@4 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <4>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 91 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm5: filter@5 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <5>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 92 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
};
dma1: dma-controller@48000000 {
compatible = "st,stm32-dma";
reg = <0x48000000 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA1>;
resets = <&rcc DMA1_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dma2: dma-controller@48001000 {
compatible = "st,stm32-dma";
reg = <0x48001000 0x400>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA2>;
resets = <&rcc DMA2_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dmamux1: dma-router@48002000 {
compatible = "st,stm32h7-dmamux";
reg = <0x48002000 0x40>;
#dma-cells = <3>;
dma-requests = <128>;
dma-masters = <&dma1 &dma2>;
dma-channels = <16>;
clocks = <&rcc DMAMUX>;
resets = <&rcc DMAMUX_R>;
};
adc: adc@48003000 {
compatible = "st,stm32mp1-adc-core";
reg = <0x48003000 0x400>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc ADC12>, <&rcc ADC12_K>;
clock-names = "bus", "adc";
interrupt-controller;
st,syscfg = <&syscfg>;
#interrupt-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
adc1: adc@0 {
compatible = "st,stm32mp1-adc";
#io-channel-cells = <1>;
reg = <0x0>;
interrupt-parent = <&adc>;
interrupts = <0>;
dmas = <&dmamux1 9 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
adc2: adc@100 {
compatible = "st,stm32mp1-adc";
#io-channel-cells = <1>;
reg = <0x100>;
interrupt-parent = <&adc>;
interrupts = <1>;
dmas = <&dmamux1 10 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
};
sdmmc3: mmc@48004000 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00253180>;
reg = <0x48004000 0x400>;
interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SDMMC3_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC3_R>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
clocks = <&rcc USBO_K>;
clock-names = "otg";
resets = <&rcc USBO_R>;
reset-names = "dwc2";
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
g-rx-fifo-size = <512>;
g-np-tx-fifo-size = <32>;
g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
dr_mode = "otg";
otg-rev = <0x200>;
usb33d-supply = <&usb33>;
status = "disabled";
};
hwspinlock: hwspinlock@4c000000 {
compatible = "st,stm32-hwspinlock";
#hwlock-cells = <1>;
reg = <0x4c000000 0x400>;
clocks = <&rcc HSEM>;
clock-names = "hwspinlock";
};
ipcc: mailbox@4c001000 {
compatible = "st,stm32mp1-ipcc";
#mbox-cells = <1>;
reg = <0x4c001000 0x400>;
st,proc-id = <0>;
interrupts-extended =
<&exti 61 1>,
<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "rx", "tx";
clocks = <&rcc IPCC>;
wakeup-source;
status = "disabled";
};
dcmi: dcmi@4c006000 {
compatible = "st,stm32-dcmi";
reg = <0x4c006000 0x400>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
resets = <&rcc CAMITF_R>;
clocks = <&rcc DCMI>;
clock-names = "mclk";
dmas = <&dmamux1 75 0x400 0x01>;
dma-names = "tx";
status = "disabled";
};
rcc: rcc@50000000 {
compatible = "st,stm32mp1-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
clock-names = "hse", "hsi", "csi", "lse", "lsi";
clocks = <&clk_hse>, <&clk_hsi>, <&clk_csi>,
<&clk_lse>, <&clk_lsi>;
};
pwr_regulators: pwr@50001000 {
compatible = "st,stm32mp1,pwr-reg";
reg = <0x50001000 0x10>;
reg11: reg11 {
regulator-name = "reg11";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
reg18: reg18 {
regulator-name = "reg18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
usb33: usb33 {
regulator-name = "usb33";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
pwr_mcu: pwr_mcu@50001014 {
compatible = "st,stm32mp151-pwr-mcu", "syscon";
reg = <0x50001014 0x4>;
};
exti: interrupt-controller@5000d000 {
compatible = "st,stm32mp1-exti", "syscon";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000d000 0x400>;
};
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
clocks = <&rcc SYSCFG>;
};
lptimer2: timer@50021000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x50021000 0x400>;
interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LPTIM2_K>;
clock-names = "mux";
wakeup-source;
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@1 {
compatible = "st,stm32-lptimer-trigger";
reg = <1>;
status = "disabled";
};
counter {
compatible = "st,stm32-lptimer-counter";
status = "disabled";
};
};
lptimer3: timer@50022000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x50022000 0x400>;
interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LPTIM3_K>;
clock-names = "mux";
wakeup-source;
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@2 {
compatible = "st,stm32-lptimer-trigger";
reg = <2>;
status = "disabled";
};
};
lptimer4: timer@50023000 {
compatible = "st,stm32-lptimer";
reg = <0x50023000 0x400>;
interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LPTIM4_K>;
clock-names = "mux";
wakeup-source;
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
};
lptimer5: timer@50024000 {
compatible = "st,stm32-lptimer";
reg = <0x50024000 0x400>;
interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LPTIM5_K>;
clock-names = "mux";
wakeup-source;
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
};
vrefbuf: vrefbuf@50025000 {
compatible = "st,stm32-vrefbuf";
reg = <0x50025000 0x8>;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <2500000>;
clocks = <&rcc VREF>;
status = "disabled";
};
sai4: sai@50027000 {
compatible = "st,stm32h7-sai";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x50027000 0x400>;
reg = <0x50027000 0x4>, <0x500273f0 0x10>;
interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
resets = <&rcc SAI4_R>;
status = "disabled";
sai4a: audio-controller@50027004 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-a";
reg = <0x04 0x20>;
clocks = <&rcc SAI4_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 99 0x400 0x01>;
status = "disabled";
};
sai4b: audio-controller@50027024 {
#sound-dai-cells = <0>;
compatible = "st,stm32-sai-sub-b";
reg = <0x24 0x20>;
clocks = <&rcc SAI4_K>;
clock-names = "sai_ck";
dmas = <&dmamux1 100 0x400 0x01>;
status = "disabled";
};
};
dts: thermal@50028000 {
compatible = "st,stm32-thermal";
reg = <0x50028000 0x100>;
interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc TMPSENS>;
clock-names = "pclk";
#thermal-sensor-cells = <0>;
status = "disabled";
};
hash1: hash@54002000 {
compatible = "st,stm32f756-hash";
reg = <0x54002000 0x400>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc HASH1>;
resets = <&rcc HASH1_R>;
dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
dma-names = "in";
dma-maxburst = <2>;
status = "disabled";
};
rng1: rng@54003000 {
compatible = "st,stm32-rng";
reg = <0x54003000 0x400>;
clocks = <&rcc RNG1_K>;
resets = <&rcc RNG1_R>;
status = "disabled";
};
mdma1: dma-controller@58000000 {
compatible = "st,stm32h7-mdma";
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
resets = <&rcc MDMA_R>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
};
fmc: memory-controller@58002000 {
#address-cells = <2>;
#size-cells = <1>;
compatible = "st,stm32mp1-fmc2-ebi";
reg = <0x58002000 0x1000>;
clocks = <&rcc FMC_K>;
resets = <&rcc FMC_R>;
status = "disabled";
ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
<1 0 0x64000000 0x04000000>, /* EBI CS 2 */
<2 0 0x68000000 0x04000000>, /* EBI CS 3 */
<3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
<4 0 0x80000000 0x10000000>; /* NAND */
nand-controller@4,0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32mp1-fmc2-nfc";
reg = <4 0x00000000 0x1000>,
<4 0x08010000 0x1000>,
<4 0x08020000 0x1000>,
<4 0x01000000 0x1000>,
<4 0x09010000 0x1000>,
<4 0x09020000 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
<&mdma1 20 0x2 0x12000a08 0x0 0x0>,
<&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
dma-names = "tx", "rx", "ecc";
status = "disabled";
};
};
qspi: spi@58003000 {
compatible = "st,stm32f469-qspi";
reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
reg-names = "qspi", "qspi_mm";
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
<&mdma1 22 0x2 0x10100008 0x0 0x0>;
dma-names = "tx", "rx";
clocks = <&rcc QSPI_K>;
resets = <&rcc QSPI_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
sdmmc1: mmc@58005000 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00253180>;
reg = <0x58005000 0x1000>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SDMMC1_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC1_R>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
sdmmc2: mmc@58007000 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00253180>;
reg = <0x58007000 0x1000>;
interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SDMMC2_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC2_R>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
crc1: crc@58009000 {
compatible = "st,stm32f7-crc";
reg = <0x58009000 0x400>;
clocks = <&rcc CRC1>;
status = "disabled";
};
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
reg = <0x5800a000 0x2000>;
reg-names = "stmmaceth";
interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
clock-names = "stmmaceth",
"mac-clk-tx",
"mac-clk-rx",
"eth-ck",
"ptp_ref",
"ethstp";
clocks = <&rcc ETHMAC>,
<&rcc ETHTX>,
<&rcc ETHRX>,
<&rcc ETHCK_K>,
<&rcc ETHPTP_K>,
<&rcc ETHSTP>;
st,syscon = <&syscfg 0x4>;
snps,mixed-burst;
snps,pbl = <2>;
snps,en-tx-lpi-clockgating;
snps,axi-config = <&stmmac_axi_config_0>;
snps,tso;
status = "disabled";
stmmac_axi_config_0: stmmac-axi-config {
snps,wr_osr_lmt = <0x7>;
snps,rd_osr_lmt = <0x7>;
snps,blen = <0 0 0 0 16 8 4>;
};
};
usbh_ohci: usb@5800c000 {
compatible = "generic-ohci";
reg = <0x5800c000 0x1000>;
clocks = <&usbphyc>, <&rcc USBH>;
resets = <&rcc USBH_R>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
usbh_ehci: usb@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&usbphyc>, <&rcc USBH>;
resets = <&rcc USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
companion = <&usbh_ohci>;
status = "disabled";
};
ltdc: display-controller@5a001000 {
compatible = "st,stm32-ltdc";
reg = <0x5a001000 0x400>;
interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LTDC_PX>;
clock-names = "lcd";
resets = <&rcc LTDC_R>;
status = "disabled";
port {
#address-cells = <1>;
#size-cells = <0>;
};
};
iwdg2: watchdog@5a002000 {
compatible = "st,stm32mp1-iwdg";
reg = <0x5a002000 0x400>;
clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
clock-names = "pclk", "lsi";
status = "disabled";
};
usbphyc: usbphyc@5a006000 {
#address-cells = <1>;
#size-cells = <0>;
#clock-cells = <0>;
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc USBPHY_K>;
resets = <&rcc USBPHY_R>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
status = "disabled";
usbphyc_port0: usb-phy@0 {
#phy-cells = <0>;
reg = <0>;
};
usbphyc_port1: usb-phy@1 {
#phy-cells = <1>;
reg = <1>;
};
};
usart1: serial@5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART1_K>;
wakeup-source;
status = "disabled";
};
spi6: spi@5c001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x5c001000 0x400>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI6_K>;
resets = <&rcc SPI6_R>;
dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
<&mdma1 35 0x0 0x40002 0x0 0x0>;
dma-names = "rx", "tx";
status = "disabled";
};
i2c4: i2c@5c002000 {
compatible = "st,stm32mp15-i2c";
reg = <0x5c002000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C4_K>;
resets = <&rcc I2C4_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x8>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
rtc: rtc@5c004000 {
compatible = "st,stm32mp1-rtc";
reg = <0x5c004000 0x400>;
clocks = <&rcc RTCAPB>, <&rcc RTC>;
clock-names = "pclk", "rtc_ck";
interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
bsec: efuse@5c005000 {
compatible = "st,stm32mp15-bsec";
reg = <0x5c005000 0x400>;
#address-cells = <1>;
#size-cells = <1>;
part_number_otp: part_number_otp@4 {
reg = <0x4 0x1>;
};
ts_cal1: calib@5c {
reg = <0x5c 0x2>;
};
ts_cal2: calib@5e {
reg = <0x5e 0x2>;
};
};
i2c6: i2c@5c009000 {
compatible = "st,stm32mp15-i2c";
reg = <0x5c009000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C6_K>;
resets = <&rcc I2C6_R>;
#address-cells = <1>;
#size-cells = <0>;
st,syscfg-fmp = <&syscfg 0x4 0x20>;
wakeup-source;
i2c-analog-filter;
status = "disabled";
};
tamp: tamp@5c00a000 {
compatible = "st,stm32-tamp", "syscon", "simple-mfd";
reg = <0x5c00a000 0x400>;
};
/*
* Break node order to solve dependency probe issue between
* pinctrl and exti.
*/
pinctrl: pinctrl@50002000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,stm32mp157-pinctrl";
ranges = <0 0x50002000 0xa400>;
interrupt-parent = <&exti>;
st,syscfg = <&exti 0x60 0xff>;
pins-are-numbered;
gpioa: gpio@50002000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x0 0x400>;
clocks = <&rcc GPIOA>;
st,bank-name = "GPIOA";
status = "disabled";
};
gpiob: gpio@50003000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x400>;
clocks = <&rcc GPIOB>;
st,bank-name = "GPIOB";
status = "disabled";
};
gpioc: gpio@50004000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x400>;
clocks = <&rcc GPIOC>;
st,bank-name = "GPIOC";
status = "disabled";
};
gpiod: gpio@50005000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x400>;
clocks = <&rcc GPIOD>;
st,bank-name = "GPIOD";
status = "disabled";
};
gpioe: gpio@50006000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x400>;
clocks = <&rcc GPIOE>;
st,bank-name = "GPIOE";
status = "disabled";
};
gpiof: gpio@50007000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x400>;
clocks = <&rcc GPIOF>;
st,bank-name = "GPIOF";
status = "disabled";
};
gpiog: gpio@50008000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x6000 0x400>;
clocks = <&rcc GPIOG>;
st,bank-name = "GPIOG";
status = "disabled";
};
gpioh: gpio@50009000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x7000 0x400>;
clocks = <&rcc GPIOH>;
st,bank-name = "GPIOH";
status = "disabled";
};
gpioi: gpio@5000a000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x8000 0x400>;
clocks = <&rcc GPIOI>;
st,bank-name = "GPIOI";
status = "disabled";
};
gpioj: gpio@5000b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x9000 0x400>;
clocks = <&rcc GPIOJ>;
st,bank-name = "GPIOJ";
status = "disabled";
};
gpiok: gpio@5000c000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0xa000 0x400>;
clocks = <&rcc GPIOK>;
st,bank-name = "GPIOK";
status = "disabled";
};
};
pinctrl_z: pinctrl@54004000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,stm32mp157-z-pinctrl";
ranges = <0 0x54004000 0x400>;
pins-are-numbered;
interrupt-parent = <&exti>;
st,syscfg = <&exti 0x60 0xff>;
gpioz: gpio@54004000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0 0x400>;
clocks = <&rcc GPIOZ>;
st,bank-name = "GPIOZ";
st,bank-ioport = <11>;
status = "disabled";
};
};
};
mlahb: ahb {
compatible = "st,mlahb", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dma-ranges = <0x00000000 0x38000000 0x10000>,
<0x10000000 0x10000000 0x60000>,
<0x30000000 0x30000000 0x60000>;
m4_rproc: m4@10000000 {
compatible = "st,stm32mp1-m4";
reg = <0x10000000 0x40000>,
<0x30000000 0x40000>,
<0x38000000 0x10000>;
resets = <&rcc MCU_R>;
st,syscfg-holdboot = <&rcc 0x10C 0x1>;
st,syscfg-tz = <&rcc 0x000 0x1>;
st,syscfg-pdds = <&pwr_mcu 0x0 0x1>;
st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
status = "disabled";
};
};
};