arch/arm/dts/fsl-ls1028a-rdb.dts

// SPDX-License-Identifier: GPL-2.0+ OR X11
/*
 * NXP ls1028ARDB device tree source
 *
 * Copyright 2019 NXP
 *
 */

/dts-v1/;

#include "fsl-ls1028a.dtsi"

/ {
	model = "NXP Layerscape 1028a RDB Board";
	compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
	aliases {
		spi0 = &fspi;
		eth0 = &enetc0;
		eth1 = &enetc2;
		eth2 = &mscc_felix_port0;
		eth3 = &mscc_felix_port1;
		eth4 = &mscc_felix_port2;
		eth5 = &mscc_felix_port3;
	};
};

&dspi0 {
	status = "okay";
};

&dspi1 {
	status = "okay";
};

&dspi2 {
	status = "okay";
};

&esdhc0 {
	status = "okay";
};

&esdhc1 {
	status = "okay";
	mmc-hs200-1_8v;
};

&fspi {
	status = "okay";

	mt35xu02g0: flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "jedec,spi-nor";
		spi-max-frequency = <50000000>;
		reg = <0>;
		spi-rx-bus-width = <8>;
		spi-tx-bus-width = <1>;
	};
};

&i2c0 {
	status = "okay";
	u-boot,dm-pre-reloc;

	 i2c-mux@77 {

		compatible = "nxp,pca9547";
		reg = <0x77>;
		#address-cells = <1>;
		#size-cells = <0>;

		i2c@3 {
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x3>;

			rtc@51 {
				compatible = "pcf2127-rtc";
				reg = <0x51>;
			};
		};
	};
};

&i2c1 {
	status = "okay";
};

&i2c2 {
	status = "okay";
};

&i2c3 {
	status = "okay";
};

&i2c4 {
	status = "okay";
};

&i2c5 {
	status = "okay";
};

&i2c6 {
	status = "okay";
};

&i2c7 {
	status = "okay";
};

&sata {
	status = "okay";
};

&serial0 {
	status = "okay";
};

&serial1 {
	status = "okay";
};

&usb1 {
	status = "okay";
};

&usb2 {
	status = "okay";
};

&enetc0 {
	status = "okay";
	phy-mode = "sgmii";
	phy-handle = <&rdb_phy0>;
};

&enetc2 {
	status = "okay";
};

&mscc_felix {
	status = "okay";
};

&mscc_felix_port0 {
	label = "swp0";
	phy-handle = <&sw_phy0>;
	phy-mode = "qsgmii";
	status = "okay";
};

&mscc_felix_port1 {
	label = "swp1";
	phy-handle = <&sw_phy1>;
	phy-mode = "qsgmii";
	status = "okay";
};

&mscc_felix_port2 {
	label = "swp2";
	phy-handle = <&sw_phy2>;
	phy-mode = "qsgmii";
	status = "okay";
};

&mscc_felix_port3 {
	label = "swp3";
	phy-handle = <&sw_phy3>;
	phy-mode = "qsgmii";
	status = "okay";
};

&mscc_felix_port4 {
	ethernet = <&enetc2>;
	status = "okay";
};

&mdio0 {
	status = "okay";
	rdb_phy0: phy@2 {
		reg = <2>;
	};

	/* VSC8514 QSGMII PHY */
	sw_phy0: phy@10 {
		reg = <0x10>;
	};

	sw_phy1: phy@11 {
		reg = <0x11>;
	};

	sw_phy2: phy@12 {
		reg = <0x12>;
	};

	sw_phy3: phy@13 {
		reg = <0x13>;
	};
};