blob: 2bdd55329d05f06cec70cc607f662eeeeaa2dbe2 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2015 Stefan Roese <sr@denx.de>
*/
#include <common.h>
#include <i2c.h>
#include <init.h>
#include <miiphy.h>
#include <net.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <linux/bitops.h>
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
#include <../serdes/a38x/high_speed_env_spec.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Those values and defines are taken from the Marvell U-Boot version
* "u-boot-2013.01-2014_T3.0"
*/
#define DB_GP_88F68XX_GPP_OUT_ENA_LOW \
(~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \
BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \
BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31)))
#define DB_GP_88F68XX_GPP_OUT_ENA_MID \
(~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \
BIT(16) | BIT(17) | BIT(18)))
#define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0
#define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x0
#define DB_GP_88F68XX_GPP_POL_LOW 0x0
#define DB_GP_88F68XX_GPP_POL_MID 0x0
/* IO expander on Marvell GP board includes e.g. fan enabling */
struct marvell_io_exp {
u8 chip;
u8 addr;
u8 val;
};
static struct marvell_io_exp io_exp[] = {
{ 0x20, 6, 0x20 }, /* Configuration registers: Bit on --> Input bits */
{ 0x20, 7, 0xC3 }, /* Configuration registers: Bit on --> Input bits */
{ 0x20, 2, 0x1D }, /* Output Data, register#0 */
{ 0x20, 3, 0x18 }, /* Output Data, register#1 */
{ 0x21, 6, 0xC3 }, /* Configuration registers: Bit on --> Input bits */
{ 0x21, 7, 0x31 }, /* Configuration registers: Bit on --> Input bits */
{ 0x21, 2, 0x08 }, /* Output Data, register#0 */
{ 0x21, 3, 0xC0 } /* Output Data, register#1 */
};
static struct serdes_map board_serdes_map[] = {
{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
};
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
{
*serdes_map_array = board_serdes_map;
*count = ARRAY_SIZE(board_serdes_map);
return 0;
}
/*
* Define the DDR layout / topology here in the board file. This will
* be used by the DDR3 init code in the SPL U-Boot version to configure
* the DDR3 controller.
*/
static struct mv_ddr_topology_map board_topology_map = {
DEBUG_LEVEL_ERROR,
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
{ { { {0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0} },
SPEED_BIN_DDR_1866L, /* speed_bin */
MV_DDR_DEV_WIDTH_8BIT, /* memory_width */
MV_DDR_DIE_CAP_4GBIT, /* mem_size */
MV_DDR_FREQ_800, /* frequency */
0, 0, /* cas_wl cas_l */
MV_DDR_TEMP_LOW, /* temperature */
MV_DDR_TIM_DEFAULT} }, /* timing */
BUS_MASK_32BIT, /* Busses mask */
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
{ {0} }, /* raw spd data */
{0} /* timing parameters */
};
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
{
/* Return the board topology as defined in the board code */
return &board_topology_map;
}
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
writel(0x11244011, MVEBU_MPP_BASE + 0x08);
writel(0x22222111, MVEBU_MPP_BASE + 0x0c);
writel(0x22200002, MVEBU_MPP_BASE + 0x10);
writel(0x30042022, MVEBU_MPP_BASE + 0x14);
writel(0x55550555, MVEBU_MPP_BASE + 0x18);
writel(0x00005550, MVEBU_MPP_BASE + 0x1c);
/* Set GPP Out value */
writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
/* Set GPP Polarity */
writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
/* Set GPP Out Enable */
writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
return 0;
}
int board_init(void)
{
int i;
/* adress of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
/* Init I2C IO expanders */
for (i = 0; i < ARRAY_SIZE(io_exp); i++)
i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
return 0;
}
int checkboard(void)
{
puts("Board: Marvell DB-88F6820-GP\n");
return 0;
}
int board_eth_init(struct bd_info *bis)
{
cpu_eth_init(bis); /* Built in controller(s) come first */
return pci_eth_init(bis);
}