| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * (C) Copyright 2012 Stephen Warren |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| */ |
| |
| #include <common.h> |
| #include <cpu_func.h> |
| #include <asm/io.h> |
| #include <asm/arch/base.h> |
| #include <asm/arch/wdog.h> |
| #include <efi_loader.h> |
| |
| #define RESET_TIMEOUT 10 |
| |
| /* |
| * The Raspberry Pi firmware uses the RSTS register to know which partiton |
| * to boot from. The partiton value is spread into bits 0, 2, 4, 6, 8, 10. |
| * Partiton 63 is a special partition used by the firmware to indicate halt. |
| */ |
| #define BCM2835_WDOG_RSTS_RASPBERRYPI_HALT 0x555 |
| |
| /* max ticks timeout */ |
| #define BCM2835_WDOG_MAX_TIMEOUT 0x000fffff |
| |
| void hw_watchdog_disable(void) {} |
| |
| __efi_runtime_data struct bcm2835_wdog_regs *wdog_regs; |
| |
| static void __efi_runtime |
| __reset_cpu(struct bcm2835_wdog_regs *wdog_regs, ulong ticks) |
| { |
| uint32_t rstc, timeout; |
| |
| if (ticks == 0) { |
| hw_watchdog_disable(); |
| timeout = RESET_TIMEOUT; |
| } else |
| timeout = ticks & BCM2835_WDOG_MAX_TIMEOUT; |
| |
| rstc = readl(&wdog_regs->rstc); |
| rstc &= ~BCM2835_WDOG_RSTC_WRCFG_MASK; |
| rstc |= BCM2835_WDOG_RSTC_WRCFG_FULL_RESET; |
| |
| writel(BCM2835_WDOG_PASSWORD | timeout, &wdog_regs->wdog); |
| writel(BCM2835_WDOG_PASSWORD | rstc, &wdog_regs->rstc); |
| } |
| |
| void reset_cpu(ulong ticks) |
| { |
| struct bcm2835_wdog_regs *regs = |
| (struct bcm2835_wdog_regs *)BCM2835_WDOG_PHYSADDR; |
| |
| __reset_cpu(regs, 0); |
| } |
| |
| #ifdef CONFIG_EFI_LOADER |
| |
| void __efi_runtime EFIAPI efi_reset_system( |
| enum efi_reset_type reset_type, |
| efi_status_t reset_status, |
| unsigned long data_size, void *reset_data) |
| { |
| u32 val; |
| |
| if (reset_type == EFI_RESET_COLD || |
| reset_type == EFI_RESET_WARM || |
| reset_type == EFI_RESET_PLATFORM_SPECIFIC) { |
| __reset_cpu(wdog_regs, 0); |
| } else if (reset_type == EFI_RESET_SHUTDOWN) { |
| /* |
| * We set the watchdog hard reset bit here to distinguish this reset |
| * from the normal (full) reset. bootcode.bin will not reboot after a |
| * hard reset. |
| */ |
| val = readl(&wdog_regs->rsts); |
| val |= BCM2835_WDOG_PASSWORD; |
| val |= BCM2835_WDOG_RSTS_RASPBERRYPI_HALT; |
| writel(val, &wdog_regs->rsts); |
| __reset_cpu(wdog_regs, 0); |
| } |
| |
| while (1) { } |
| } |
| |
| efi_status_t efi_reset_system_init(void) |
| { |
| wdog_regs = (struct bcm2835_wdog_regs *)BCM2835_WDOG_PHYSADDR; |
| return efi_add_runtime_mmio(&wdog_regs, sizeof(*wdog_regs)); |
| } |
| |
| #endif |