| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * board/renesas/ulcb/ulcb.c |
| * This file is ULCB board support. |
| * |
| * Copyright (C) 2017 Renesas Electronics Corporation |
| */ |
| |
| #include <common.h> |
| #include <malloc.h> |
| #include <netdev.h> |
| #include <dm.h> |
| #include <dm/platform_data/serial_sh.h> |
| #include <asm/processor.h> |
| #include <asm/mach-types.h> |
| #include <asm/io.h> |
| #include <linux/errno.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/gpio.h> |
| #include <asm/arch/gpio.h> |
| #include <asm/arch/rmobile.h> |
| #include <asm/arch/rcar-mstp.h> |
| #include <asm/arch/sh_sdhi.h> |
| #include <i2c.h> |
| #include <mmc.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define CPGWPCR 0xE6150904 |
| #define CPGWPR 0xE615090C |
| |
| #define CLK2MHZ(clk) (clk / 1000 / 1000) |
| void s_init(void) |
| { |
| struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; |
| struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; |
| |
| /* Watchdog init */ |
| writel(0xA5A5A500, &rwdt->rwtcsra); |
| writel(0xA5A5A500, &swdt->swtcsra); |
| |
| writel(0xA5A50000, CPGWPCR); |
| writel(0xFFFFFFFF, CPGWPR); |
| } |
| |
| #define GSX_MSTP112 BIT(12) /* 3DG */ |
| #define TMU0_MSTP125 BIT(25) /* secure */ |
| #define TMU1_MSTP124 BIT(24) /* non-secure */ |
| #define SCIF2_MSTP310 BIT(10) /* SCIF2 */ |
| #define DVFS_MSTP926 BIT(26) |
| #define HSUSB_MSTP704 BIT(4) /* HSUSB */ |
| |
| int board_early_init_f(void) |
| { |
| /* TMU0,1 */ /* which use ? */ |
| mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125 | TMU1_MSTP124); |
| |
| #if defined(CONFIG_SYS_I2C) && defined(CONFIG_SYS_I2C_SH) |
| /* DVFS for reset */ |
| mstp_clrbits_le32(MSTPSR9, SMSTPCR9, DVFS_MSTP926); |
| #endif |
| return 0; |
| } |
| |
| /* SYSC */ |
| /* R/- 32 Power status register 2(3DG) */ |
| #define SYSC_PWRSR2 0xE6180100 |
| /* -/W 32 Power resume control register 2 (3DG) */ |
| #define SYSC_PWRONCR2 0xE618010C |
| |
| /* HSUSB block registers */ |
| #define HSUSB_REG_LPSTS 0xE6590102 |
| #define HSUSB_REG_LPSTS_SUSPM_NORMAL BIT(14) |
| #define HSUSB_REG_UGCTRL2 0xE6590184 |
| #define HSUSB_REG_UGCTRL2_USB0SEL 0x30 |
| #define HSUSB_REG_UGCTRL2_USB0SEL_EHCI 0x10 |
| |
| int board_init(void) |
| { |
| /* adress of boot parameters */ |
| gd->bd->bi_boot_params = CONFIG_SYS_TEXT_BASE + 0x50000; |
| |
| /* USB1 pull-up */ |
| setbits_le32(PFC_PUEN6, PUEN_USB1_OVC | PUEN_USB1_PWEN); |
| |
| /* Configure the HSUSB block */ |
| mstp_clrbits_le32(MSTPSR7, SMSTPCR7, HSUSB_MSTP704); |
| /* Choice USB0SEL */ |
| clrsetbits_le32(HSUSB_REG_UGCTRL2, HSUSB_REG_UGCTRL2_USB0SEL, |
| HSUSB_REG_UGCTRL2_USB0SEL_EHCI); |
| /* low power status */ |
| setbits_le16(HSUSB_REG_LPSTS, HSUSB_REG_LPSTS_SUSPM_NORMAL); |
| |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| if (fdtdec_setup_mem_size_base() != 0) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| int dram_init_banksize(void) |
| { |
| fdtdec_setup_memory_banksize(); |
| |
| return 0; |
| } |