| ====================================================================== |
| Changes since U-Boot 1.0.1: |
| ====================================================================== |
| |
| * Some code cleanup |
| |
| * Patch by Josef Baumgartner, 10 Feb 2004: |
| Fixes for Coldfire port |
| |
| * Patch by Brad Kemp, 11 Feb 2004: |
| Fix CFI flash driver problems |
| |
| * Make sure to use a bus clock divider of 2 only when running TQM8xxM |
| modules at CPU clock frequencies above 66 MHz. |
| |
| * Optimize flash programming speed for LWMON (by another 100% :-) |
| |
| * Patch by Jian Zhang, 3 Feb 2004: |
| - Changed the incorrect FAT12BUFSIZE |
| - data_begin in fsdata can be negative. Changed it to be short. |
| |
| * Patches by Stephan Linz, 30 Jan 2004: |
| 1: - board/altera/common/flash.c:flash_erase(): |
| o allow interrupts befor get_timer() call |
| o check-up each erased sector and avoid unexpected timeouts |
| - board/altera/dk1c20/dk1s10.c:board_early_init_f(): |
| o enclose sevenseg_set() in cpp condition |
| - remove the ASMI configuration for DK1S10_standard_32 (never present) |
| - fix some typed in mistakes in the NIOS documentation |
| 2: - split DK1C20 configuration into several header files: |
| o two new files for each NIOS CPU description |
| o U-Boot related part is remaining in DK1C20.h |
| 3: - split DK1S10 configuration into several header files: |
| o two new files for each NIOS CPU description |
| o U-Boot related part is remaining in DK1S10.h |
| 4: - Add support for the Microtronix Linux Development Kit |
| NIOS CPU configuration at the Altera Nios Development Kit, |
| Stratix Edition (DK-1S10) |
| 5: - Add documentation for the Altera Nios Development Kit, |
| Stratix Edition (DK-1S10) |
| 6: - Add support for the Nios Serial Peripharel Interface (SPI) |
| (master only) |
| 7: - Add support for the common U-Boot SPI framework at |
| RTC driver DS1306 |
| |
| * Patch by Rahul Shanbhag, 28 Jan 2004: |
| Fix flash protection/locking handling for OMAP1610 innovator board. |
| |
| * Patch by Rolf Peukert, 28 Jan 2004: |
| fix flash write problems on CSB226 board (write with 32 bit bus width) |
| |
| * Patches by Mark Jonas, 16 Jan 2004: |
| - fix rounding error when calculating baudrates for MPC5200 PSCs |
| - make sure CFG_RAMBOOT and CFG_LOWBOOT are not enabled at the same |
| time which is not supported |
| |
| * Patch by Yuli Barcohen, 26 Jan 2004: |
| Allow bzip2 compression for small memory footprint boards |
| |
| * Patch by Brad Kemp, 21 Jan 2004: |
| Add support for CFI flash driver for both the Intel and the AMD |
| command sets. |
| |
| * Patch by Travis Sawyer, 20 Jan 2004: |
| Fix pci bridge auto enumeration of sibling p2p bridges. |
| |
| * Patch by Tolunay Orkun, 12 Jan 2004: |
| Add some delays as needed for Intel LXT971A PHY support |
| |
| * Patches by Stephan Linz, 09 Jan 2004: |
| - avoid warning: unused variable `piop' in board/altera/common/sevenseg.c |
| - make DK1C20 board configuration related to ASMI conform to |
| documentation |
| |
| * Patch by Anders Larsen, 09 Jan 2004: |
| |
| ARM memory layout fixes: the abort-stack is now set up in the |
| correct RAM area, and the BSS is zeroed out as it should be. |
| |
| Furthermore, the magic variables 'armboot_end' and 'armboot_end_data' |
| of the linker scripts are replaced by '__bss_start' and '_end', |
| resp., which is a further step to eliminate unnecessary differences |
| between the implementation of the CPU architectures. |
| |
| * Patch by liang a lei, 9 Jan 2004: |
| Fix Intel 28F128J3 ID in include/flash.h |
| |
| * Patch by Masami Komiya, 09 Jan 2004: |
| add support for TB0229 board (NEC VR4131 MIPS processor) |
| |
| * Patch by Leon Kukovec, 12 Dec 2003: |
| changed extern __inline__ into static __inline__ in |
| include/linux/byteorder/swab.h |
| |
| * Patch by Travis Sawyer, 30 Dec 2003: |
| Add support for IBM PPC440GX. Multiple EMAC Ethernet devices, |
| select MDI port based on enabled EMAC device. |
| Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX |
| base PrPMC board. |
| |
| * Patch by Wolter Kamphuis, 15 Dec 2003: |
| made CONFIG_SILENT_CONSOLE usable on all architectures |
| |
| * Disable date command on TQM866M - there is no RTC on MPC866 |
| |
| * Fix variable CPU clock for MPC859/866 systems for low CPU clocks |
| |
| * Implement adaptive SDRAM timing configuration based on actual CPU |
| clock frequency for INCA-IP; fix problem with board hanging when |
| switching from 150MHz to 100MHz |
| |
| * Add PCMCIA CS support for BMS2003 board |
| |
| * Add variable CPU clock for MPC859/866 systems (so far only TQM866M): |
| see doc/README.MPC866 for details; |
| implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866; |
| calculate CPU clock frequency from PLL register values. |
| |
| * Add support for 128 MB RAM on TQM8xxL/M modules |
| |
| * Fix PS/2 keyboard problem caused by statically initialized variable |
| pointing to a location in flash |
| |
| * Fix INCA-IP clock calculation: 400/3 = 133.3 MHz, not 130. |
| |
| * The PS/2 mux on the BMS2003 board needs 450 ms after power on |
| before we can access it; add delay in case we are faster (with no |
| CF card inserted) |
| |
| * Cleanup of some init functions |
| |
| * Make sure SCC Ethernet is always stopped by the time we boot Linux |
| to avoid Linux crashes by early packets coming in. |
| |
| * Accelerate flash accesses on LWMON board by using buffered writes |
| |
| * Fix typo in Makefile; |
| fix problem with PARTNUM detection |
| |
| * Patch by Reinhard Meyer, 09 Jan 2004: |
| - add RTC support for MPC5200 based boards (requires RTC_XTAL) |
| |
| * Add support for IDE LED on BMS2003 board |
| (exclusive with status LED!) |
| |
| * Add support for PS/2 keyboard (used with PS/2 multiplexor on |
| BMS2003 board) |
| |
| * Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004: |
| Add common files for "emk" boards |
| |
| * Add a common get_ram_size() function and modify the the |
| board-specific files to invoke that common implementation. |
| |
| ====================================================================== |
| Changes for U-Boot 1.0.1: |
| ====================================================================== |
| |
| * Set default clock for INCA-IP to 150 MHz |
| |
| * Make BMS2003 use a separate config file to avoid #ifdef mess; |
| add I2C support; add support for DS1337 RTC |
| |
| * Add CompactFlash support for BMS2003 board |
| |
| * Add support for status LED on BMS2003 board |
| |
| * Patch by Scott McNutt, 02 Jan 2004: |
| Add support for the Nios Active Serial Memory Interface (ASMI) |
| on Cyclone devices |
| |
| * Patch by Andrea Marson, 16 Dec 2003: |
| Add support for the PPChameleon ME and HI modules |
| |
| * Patch by Yuli Barcohen, 22 Dec 2003: |
| Add support for Motorola DUET ADS board (MPC87x/88x) |
| |
| * Patch by Robert Schwebel, 15 Dec 2003: |
| add support for cramfs (uses JFFS2 command interface) |
| |
| * Patches by Stephan Linz, 11 Dec 2003: |
| - more documentation for NIOS port |
| - new struct nios_pio_t, struct nios_spi_t |
| - Reconfiguration for NIOS Development Kit DK1C20: |
| o move board related code from board/dk1c20 |
| to board/altera/dk1c20 |
| o create a new common source path board/altera/common |
| and move generic flash access stuff into it |
| o change/expand configuration file DK1C20.h |
| - Add support for NIOS Development Kit DK1S10 |
| - Add status LED support for NIOS systems |
| - Add dual 7-segment LED support for Altera NIOS DevKits |
| |
| * Patch by Ronen Shitrit, 10 Dec 2003: |
| Add support for the Marvell DB64360 / DB64460 development boards |
| |
| * Patch by Detlev Zundel, 10 Dec 2003: |
| fix dependency problem in examples/Makefile |
| |
| * Patch by Denis Peter, 8 Dec 2003 |
| - add support for the PATI board (MPC555) |
| - add SPI support for the MPC5xx |
| |
| * Patch by Anders Larsen, 08 Dec 2003: |
| add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG |
| to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target; |
| cleanup some redundand #defines |
| |
| * Patch by André Schwarz, 8 Dec 2003: |
| fixes for Davicom DM9102A Ethernet Chip (#define CONFIG_TULIP_FIX_DAVICOM): |
| - TX and RX deskriptors must be quad-word aligned |
| - does not work with only one TX deskriptor |
| - standard reset method does not work |
| |
| * Patch by Masami Komiya, 08 Dec 2003: |
| add RTL8139 ethernet driver |
| |
| * Patches by Ed Okerson, 07 Dec 2003: |
| - fix ethernet for the AU1x00 processors in little-endian mode. |
| - extend memsetup.S for the AU1x00 processors in BE and LE modes |
| |
| * Minor code cleanup (coding style) |
| |
| * Patch by Reinhard Meyer, 30 Dec 2003: |
| - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE, |
| - added CONFIG_PHY_ADDR to include/configs/IceCube.h, |
| - turned debug print of PHY registers into a function (called in two places) |
| - added support for EMK MPC5200 based modules |
| |
| * Fix MPC8xx PLPRCR_MFD_SHIFT typo |
| |
| * Add support for TQM866M modules |
| |
| * Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash) |
| |
| * Fix a few compiler warnings |
| |
| * Patch by Reinhard Meyer, 28 Dec 2003: |
| Add initial support for TOP5200 board |
| |
| * Make CPU clock on ICA-IP board controllable by a "cpuclk" |
| environment variable which can set to "100", "133", or "150". The |
| CPU clock will be configured accordingly upon next reboot. Other |
| values are ignored. In case of an invalid or undefined "cpuclk" |
| value, the compile-time default CPU clock speed will be used. |
| |
| * Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory |
| window that is used to access the UART registers by the Linux driver) |
| |
| * Patch by Reinhard Meyer, 20 Dec 2003: |
| Fix clock calculation for the MPC5200 for higher clock frequencies |
| (above 2**32 / 10 = 429.5 MHz). |
| |
| * Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration |
| |
| * Fix IceCube CLKIN configuration (it's 33.000000MHz) |
| |
| * Add new configuration for IceCube board with DDR memory |
| |
| * Update TRAB memory configurations |
| |
| * Add JFFS2 support for INCA-IP board |
| |
| * Patch by Bill Hargen, 09 Dec 2003: |
| - BUBINGA405EP: changed flash driver to protect top sector containing |
| first instruction. |
| - BUBINGA405EP: configured "eeprom" command to access boot config EEPROM. |
| - BUBINGA405EP: fixed PLL init (init chip selects before FPGA/NVRAM access). |
| - 405EP: fixed SPD-based SDRAM init (only use banks 0 and 1). |
| - 405EP: added/fixed support for "reginfo" command. |
| - 4xx: removed spurious MII error messages on "mii info" command. |
| |
| * Patch by Bernhard Kuhn, 28 Nov 2003: |
| add support for Coldfire CPU |
| add support for Motorola M5272C3 and M5282EVB boards |
| |
| * Patch by Pierre Aubert, 24 Nov 2003: |
| - add a return value for the fpga command |
| - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT |
| is defined. If ide_preinit fails, ide_init is aborted. |
| - fix an endianess problem in fat.h |
| |
| * Patch by Wolter Kamphuis, 05 Dec 2003: |
| Add support for SNMC's QS850/QS823/QS860T boards |
| |
| * Patch by Yuli Barcohen, 3 Dec 2003: |
| "revive" U-Boot support for old Motorola MPC860ADS board |
| |
| * Patch by Cam(ilo?), 03 Dec 2003: |
| make examples build even with broken Montavista objcopy |
| |
| * Patch by Pavel Bartusek, 27 Nov 2003: |
| fix conversion problem with "bootretry" evironment variable |
| |
| * Patch by Andre Schwarz, 24 Nov 2003: |
| add support for mvblue (mvBlueLYNX and mvBlueBOX) boards |
| |
| * Patch by Pavel Bartusek, 21 Nov 2003: |
| set ZMII bridge speed on 440 |
| |
| * Patch by Anders Larsen, 17 Nov 2003: |
| Fix mismatched #ifdef / #endif in include/asm-arm/arch-pxa/hardware.h |
| |
| * Patches by David Müller, 14 Nov 2003: |
| - board/mpl/common/common_util.c |
| * implement support for BZIP2 compressed images |
| * various cleanups (printf -> puts, ...) |
| - board/mpl/common/flash.c |
| * report correct errors to upper layers |
| * check the erase fail and VPP low bits in status reg |
| - board/mpl/vcma9/cmd_vcma9.c |
| - board/mpl/vcma9/flash.c |
| * various cleanups (printf -> puts, ...) |
| - common/cmd_usb.c |
| * fix typo in comment |
| - cpu/arm920t/usb_ohci.c |
| * support for S3C2410 is missing in #if line |
| - drivers/cs8900.c |
| * reinit some registers in case of error (cable missing, ...) |
| - fs/fat/fat.c |
| * support for USB/MMC devices is missing in #if line |
| - include/configs/MIP405.h |
| - include/configs/PIP405.h |
| * enable BZIP2 support |
| * enlarge malloc space to 1MiB because of BZIP2 support |
| - include/configs/VCMA9.h |
| * enable BZIP2 support |
| * enlarge malloc space to 1MiB because of BZIP2 support |
| * enable USB support |
| - lib_arm/armlinux.c |
| * change calling convention of ARM Linux kernel as |
| described on http://www.arm.linux.org.uk/developer/booting.php |
| |
| * Patch by Thomas Lange, 14 Nov 2003: |
| Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to |
| support all these AMD boards. |
| |
| * Patch by Thomas Lange, 14 Nov 2003: |
| Workaround for mips au1x00 physical memory accesses (the au1x00 |
| uses a 36 bit bus internally and cannot access physical memory |
| directly. Use the uncached SDRAM address instead of the physical |
| one.) |
| |
| * Patch by Xue Ligong (Joe), 13 Nov 2003: |
| add Realtek 8019 ethernet driver |
| |
| * Patch by Yuli Barcohen, 13 Nov 2003: |
| MPC826xADS/PQ2FADS cleanup |
| |
| * Patch by Anders Larsen, 12 Nov 2003: |
| Update README to mark the PORTIO commands non-standard |
| |
| * Patch by Nicolas Lacressonnière, 12 Nov 2003: |
| update for for Atmel AT91RM9200DK development kit: |
| - support for environment variables in DataFlash |
| - Atmel DataFlash AT45DB1282 support |
| |
| * Patch by Jeff Carr, 11 Nov 2003: |
| add support for new version of 8270 processors |
| |
| * Patches by George G. Davis, 05 Nov 2003: |
| - only pass the ARM linux initrd tag to the kernel when an initrd |
| is actually present |
| - update omap1510inn configuration file |
| |
| * Patches by Stephan Linz, 3 Nov 2003: |
| - more endianess fixes for LAN91C111 driver |
| - CFG_HZ configuration patch for NIOS Cyclone board |
| |
| * Patch by Stephan Linz, 28 Oct 2003: |
| fix PHY_INT_REG vs. PHY_MASK_REG bug in drivers/smc91111.c |
| |
| * Patch by Steven Scholz, 20 Oct 2003: |
| - make "mii info <addr>" show infor for PHY at "addr" only |
| - Endian fix for miiphy_info() |
| |
| * Patch by Gleb Natapov, 19 Sep 2003: |
| Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c |
| |
| * Patch by Anders Larsen, 17 Sep 2003: |
| Bring ARM memory layout in sync with the documentation: |
| stack and malloc-heap are now located _below_ the U-Boot code |
| |
| * Accelerate booting on TRAB board: read and check autoupdate image |
| headers first instead of always reading the whole images. |
| |
| * Fix type in MPC5XXX code (pointed out by Victor Wren) |
| |
| * Enabled password check on RMU board |
| |
| * Fix configuration problem with IceCube in LOWBOOT configuration: |
| envrionment got embedded, corrupting the image layout. |
| |
| * Fix NEC display names (it's 6440 [for 640x480], not 6640). |
| |
| * Added BMS2003 board |
| add support for NEC NL6448BC33-54. 10.4", 640x480 TFT display |
| |
| * Fix flash driver for TRAB board (must use Unlock Bypass Reset |
| command to exit Unlock Bypass Mode); adjust timings for flash, SRAM |
| and CPLD |
| |
| * Use "-fPIC" instead of "-mrelocatable" to prevent problems with |
| recent tools |
| |
| * Add checksum verification to 'imls' command |
| |
| * Add bd_info fields needed for 4xx Linux I2C driver |
| |
| * Patch by Martin Krause, 4 Nov. 2003: |
| Fix error in cmd_vfd.c (TRAB board: "vfd /1" shows now only one Bitmap) |
| |
| * Print used network interface when CONFIG_NET_MULTI is set |
| |
| * Patch by Bernhard Kuhn, 28 Oct 2003: |
| Add low boot support for MPC5200 |
| |
| * Fix problem with dual PCMCIA support (NSCU) |
| |
| * Fix MPC5200 I2C initialization function |
| |
| ====================================================================== |
| Changes for U-Boot 1.0.0: |
| ====================================================================== |
| |
| * Fix parameter passing to standalone images with bootm command |
| |
| * Patch by Kyle Harris, 30 Oct 2003: |
| Fix build errors for ixdp425 board |
| |
| * Patch by David M. Horn, 29 Oct 2003: |
| Fixes to build under CYGWIN |
| |
| * Get IceCube MGT5100 working (again) |
| |
| * Fix problems in memory test on some boards (which was not |
| non-destructive as intended) |
| |
| * Patch by Gary Jennejohn, 28 Oct 2003: |
| Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack |
| to prevent stack overflow on ARM systems |
| |
| * Patch by Stephan Linz, 28 Oct 2003: |
| fix init sequence error for NIOS port |
| |
| * Allow lowercase spelling for IceCube_5200; support MPC5200LITE name |
| |
| * Add CONFIG_VERSION_VARIABLE to TRAB configuration |
| |
| * Patch by Xiao Xianghua, 23 Oct 2003: |
| small patch for mpc85xx |
| |
| * Fix small problem in MPC5200 I2C driver |
| |
| * Fix FCC3 support on ATC board |
| |
| * Correct header printing for multi-image files in do_bootm() |
| |
| * Make CONFIG_SILENT_CONSOLE work with CONFIG_AUTOBOOT_KEYED |
| |
| * Fix PCI problems on PPChameleon board |
| |
| * Patch by Steven Scholz, 18 Oct 2003: |
| Fix AT91RM9200 ethernet driver |
| |
| * Patch by Nye Liu, 17 Oct 2003: |
| Fix typo in include/mpc8xx.h |
| |
| * Patch by Richard Woodruff, 16 Oct 03: |
| Fixes for cpu/arm925/interrupt.c |
| - Initialize timestamp & lastdec vars. |
| - fix timestamp overflows. |
| - fix lastdec overflow. |
| - smarter normalization to allow udelay() below 1ms to work. |
| |
| * Patch by Scott McNutt, 16 Oct |
| add networking support for the Altera Nios Development Kit, |
| Cyclone Edition (DK-1C20) |
| |
| * Patch by Jon Diekema, 14 Oct 2003: |
| add hint about doc/README.silent to README file |
| |
| * Add CompactFlash support for NSCU |
| |
| * Fix PCI problems on PPChameleonEVB |
| |
| * TRAB auto-update: Base decision if we have to strip the image |
| header on image type as encoded in the header |
| (include image type patch by Martin Krause, 17 Oct 2003) |
| |
| * Patches by Xianghua Xiao, 15 Oct 2003: |
| |
| - Added Motorola CPU 8540/8560 support (cpu/85xx) |
| - Added Motorola MPC8540ADS board support (board/mpc8540ads) |
| - Added Motorola MPC8560ADS board support (board/mpc8560ads) |
| |
| * Fix flash timings on TRAB board |
| |
| * Make sure HUSH is initialized for running auto-update scripts |
| |
| * Make 5200 reset command _really_ reset the board, without running |
| any other code after it |
| |
| * Fix errors with flash erase when range spans across banks |
| that are mapped in reverse order |
| |
| * Fix flash mapping and display on P3G4 board |
| |
| * Patch by Kyle Harris, 15 Jul 2003: |
| - add support for Intel IXP425 CPU |
| - add support for IXDP425 eval board |
| |
| * Added config option CONFIG_SILENT_CONSOLE. See doc/README.silent |
| for more information |
| |
| * Patch by Steven Scholz, 10 Oct 2003 |
| - Add support for Altera FPGA ACEX1K |
| |
| * Patches by Thomas Lange, 09 Oct 2003: |
| - fix cmd_ide.c for non ppc boards (read/write functions did not |
| add ATA base address) |
| - fix for shannon board |
| - #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code |
| - Endian swap ATA identity for all big endian CPUs, not just PPC |
| - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize |
| args to linux |
| - add support for dbau1x00 board (MIPS32) |
| |
| * Patch by Sangmoon Kim, 07 Oct 2003: |
| add support for debris board |
| |
| * Patch by Martin Krause, 09 Oct 2003: |
| Fixes for TRAB board |
| - /board/trab/rs485.c: correct baudrate |
| - /board/trab/cmd_trab.c: bug fix for problem with timer overflow in |
| udelay(); fix some timing problems with adc controller |
| - /board/trab/trab_fkt.c: add new commands: gain, eeprom and power; |
| modify commands: touch and buzzer |
| |
| * Disable CONFIG_SUPPORT_VFAT when used with CONFIG_AUTO_UPDATE |
| (quick & dirty workaround for rogue pointer problem in get_vfatname()); |
| Use direct function calls for auto_update instead of hush commands |
| |
| * Patch by Scott McNutt, 04 Oct 2003: |
| - add support for Altera Nios-32 CPU |
| - add support for Nios Cyclone Development Kit (DK-1C20) |
| |
| * Patch by Steven Scholz, 29 Sep 2003: |
| - A second parameter for bootm overwrites the load address for |
| "Standalone Application" images. |
| - bootm sets environment variable "filesize" to the resulting |
| (uncompressed) data length for "Standalone Application" images |
| when autostart is set to "no". Now you can do something like |
| if bootm $fpgadata $some_free_ram ; then |
| fpga load 0 $some_free_ram $filesize |
| fi |
| |
| * Patch by Denis Peter, 25 Sept 2003: |
| add support for the MIP405 Rev. C board |
| |
| * Patch by Yuli Barcohen, 25 Sep 2003: |
| add support for Zephyr Engineering ZPC.1900 board |
| |
| * Patch by Anders Larsen, 23 Sep 2003: |
| add CMD_PORTIO to CFG_CMD_NONSTD (commands in question are only |
| implemented for the x86 architecture) |
| |
| * Patch by Sangmoon Kim, 23 Sep 2003: |
| fix pll_pci_to_mem_multiplier table for MPC8245 |
| |
| * Patch by Anders Larsen, 22 Sep 2003: |
| enable timed autoboot on PXA |
| |
| * Patch by David Müller, 22 Sep 2003: |
| - add $(CFLAGS) to "-print-libgcc-filename" so compiler driver |
| returns correct libgcc file path |
| - "latency" reduction of busy-loop waiting to improve "U-Boot" boot |
| time on s3c24x0 systems |
| |
| * Patch by Jon Diekema, 19 Sep 2003: |
| - Add CFG_FAULT_ECHO_LINK_DOWN option to echo the inverted Ethernet |
| link state to the fault LED. |
| - In NetLoop, make the Fault LED reflect the link status. The link |
| status gets updated on entry, and on timeouts. |
| |
| * Patch by Anders Larsen, 18 Sep 2003: |
| allow mkimage to build and run on Cygwin-hosted systems |
| |
| * Patch by Frank Müller, 18 Sep 2003: |
| use bi_intfreq instead of bi_busfreq to compute fec_mii_speed in |
| cpu/mpc8xx/fec.c |
| |
| * Patch by Pantelis Antoniou, 16 Sep 2003: |
| add tool to compute fileds in the PLPRCR register for MPC86x |
| |
| * Use IH_TYPE_FILESYSTEM for TRAB "disk" images. |
| |
| * Fix build problems under FreeBSD |
| |
| * Add generic filesystem image type |
| |
| * Make fatload set filesize environment variable |
| |
| * enable basic / medium / high-end configurations for PPChameleonEVB |
| board; fix NAND code |
| |
| * enable TFTP client code to specify to the server the desired |
| timeout value (see RFC-2349) |
| |
| * Improve SDRAM setup for TRAB board |
| |
| * Suppress all output with splashscreen configured only if "splashimage" |
| is set |
| |
| * Fix problems with I2C support for mpc5200 |
| |
| * Adapt TRAB configuration and auto_update to new memory layout |
| |
| * Add configuration for wtk board |
| |
| * Add support for the Sharp LQ065T9DR51U LCD display |
| |
| * Patch by Rune Torgersen, 17 Sep 2003: |
| - Fixes for MPC8266 default config |
| - Allow eth_loopback_test() on 8260 to use a subset of the FCC's |
| |
| * Patches by Jon Diekema, 17 Sep 2003: |
| - update README (SHOW_BOOT_PROGRESS values for cmd_nand.c and |
| env_common.c) |
| - sbc8260 tweaks |
| - adjust "help" output |
| |
| * Patches by Anders Larsen, 17 Sep 2003: |
| - fix spelling errors |
| - set GD_FLG_DEVINIT flag only after device function pointers |
| are valid |
| - Allow CFG_ALT_MEMTEST on systems where address zero isn't |
| writeable |
| - enable 3.rd UART (ST-UART) on PXA(XScale) CPUs |
| - trigger watchdog while waiting in serial driver |
| |
| * Add auto-update code for TRAB board using USB memory sticks, |
| support new configuration with more memory |
| |
| * disable MPC5200 bus pipelining as workaround for bus contention |
| |
| * Modify XLB arbiter priorities on MPC5200 so all devices use same |
| priority; configure critical interrupts to be handled like external |
| interrupts |
| |
| * Make IPB clock on MGT5100/MPC5200 configurable in board config file; |
| go back to 66 MHz for stability |
| |
| * Patches by Jon Diekema, 15 Sep 2003: |
| - add description for missing CFG_CMD_* entries in the README file |
| - sacsng tweaks |
| |
| * Patch by Gleb Natapov, 14 Sep 2003: |
| enable watchdog support for all MPC824x boards that have a watchdog |
| |
| * On MPC5200, restrict FEC to a maximum of 10 Mbps to work around the |
| "Non-octet Aligned Frame" errors we see at 100 Mbps |
| |
| * Patch by Sharad Gupta, 14 Sep 2003: |
| fix SPR numbers for upper BAT register ([ID]BAT[4-7][UL]) |
| |
| * Patch by llandre, 11 Sep 2003: |
| update configuration for PPChameleonEVB board |
| |
| * Patch by David Müller, 13 Sep 2003: |
| various changes to VCMA9 board specific files |
| |
| * Add I2C support for MGT5100 / MPC5200 |
| |
| * Patch by Rune Torgersen, 11 Sep 2003: |
| Changed default memory option on MPC8266ADS to NOT be Page Based |
| Interleave, since this doesn't work very well with the standard |
| 16MB DIMM |
| |
| * Patch by George G. Davis, 12 Sep 2003: |
| fix Makefile settings for sk98 driver |
| |
| * Patch by Stefan Roese, 12 Sep 2003: |
| - new boards added: DP405, HUB405, PLU405, VOH405 |
| - some esd boards updated |
| - cpu/ppc4xx/sdram.c: disable memory controller before setting |
| first values |
| - cpu/ppc4xx/405_pci.c: set vendor id on PPC405EP systems |
| |
| * Patch by Martin Krause, 11 Sep 2003: |
| add burn-in tests for TRAB board |
| |
| * Enable instruction cache on MPC5200 board |
| |
| * Patch by Denis Peter, 11 Sep 2003: |
| - fix USB data pointer assignment for bulk only transfer. |
| - prevent to display erased directories in FAT filesystem. |
| |
| * Change output format for NAND flash - make it look like for other |
| memory, too |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.8: |
| ====================================================================== |
| |
| * Add I2C and RTC support for RMU board |
| |
| * Patches by Denis Peter, 9 Sep 2003: |
| add FAT support for IDE, SCSI and USB |
| |
| * Patches by Gleb Natapov, 2 Sep 2003: |
| - cleanup of POST code for unsupported architectures |
| - MPC824x locks way0 of data cache for use as initial RAM; |
| this patch unlocks it after relocation to RAM and invalidates |
| the locked entries. |
| |
| * Patch by Gleb Natapov, 30 Aug 2003: |
| new I2C driver for mpc107 bridge. Now works from flash. |
| |
| * Patch by Dave Ellis, 11 Aug 2003: |
| - JFFS2: fix typo in common/cmd_jffs2.c |
| - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option |
| - JFFS2: remove node version 0 warning |
| - JFFS2: accept JFFS2 PADDING nodes |
| - SXNI855T: add AM29LV800 support |
| - SXNI855T: move environment from EEPROM to flash |
| - SXNI855T: boot from JFFS2 in NOR or NAND flash |
| |
| * Patch by Bill Hargen, 11 Aug 2003: |
| fixes for I2C on MPC8240 |
| - fix i2c_write routine |
| - fix iprobe command |
| - eliminates use of global variables, plus dead code, cleanup. |
| |
| * Add support for USB Mass Storage Devices (BBB) |
| (tested with USB memory sticks only) |
| |
| * Avoid flicker on TRAB's VFD |
| |
| * Add support for SK98xx driver |
| |
| * Add PCI support for SL8245 board |
| |
| * Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB) |
| or 1 x AM29LV652 (two LV065 in one chip = 16 MB); |
| Run IPB at 133 Mhz; adjust the MII clock frequency accordingly |
| |
| * Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz) |
| to allow for more accurate baudrate settings |
| (error now 0.7% at 115 kbps, instead of 3.5% before) |
| |
| * Patch by Andreas Mohr, 4 Sep 2003: |
| Fix a lot of spelling errors |
| |
| * Add support for PPChameleon Eval Board |
| |
| * Add support for P3G4 board |
| |
| * Fix problem with MGT5100 FEC driver: add "early" MAC address |
| initialization |
| |
| * Patch by Yuli Barcohen, 7 Aug 2003: |
| check BCSR to detect if the board is configured in PCI mode |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.7: |
| ====================================================================== |
| |
| * Patch by Raghu Krishnaprasad, 7 Aug 2003: |
| add support for Adder II MPC852T module |
| |
| * Patch by George G. Davis, 19 Aug 2003: |
| fix TI Innovator/OMAP1510 pin configs |
| |
| * Patches by Kshitij, 18 Aug 2003 |
| - add support for arm926ejs cpu core |
| - add support for TI OMAP 1610 Innovator Board |
| |
| * Patch by Yuli Barcohen, 14 Aug 2003: |
| add support for bzip2 uncompression |
| |
| * Add GCC library to examples/Makefile so GCC utility functions will |
| be resolved, too |
| |
| * Add I2C and RTC support for RMU board using software I2C driver |
| (because of better response to iprobe command); fix problem with |
| "reset" command |
| |
| * Patch by Matthias Fuchs, 28 Aug 2003: |
| Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to |
| CONFIG_BOOTP_MAKS (see README). |
| |
| * Fix ICU862 environment problem |
| |
| * Fix RAM size detection for RMU board |
| |
| * Implement "reset" for MGT5100/MPC5200 systems |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.6: |
| ====================================================================== |
| |
| * Make Ethernet autonegotiation on INCA-IP work for all clock rates; |
| allow selection of clock frequency as "make" target |
| |
| * Implement memory autosizing code for IceCube boards |
| |
| * Configure network port on INCA-IP for autonegotiation |
| |
| * Fix overflow problem in network timeout code |
| |
| * Patch by Richard Woodruff, 8 Aug 2003: |
| Allow crc32 to be used at address 0x000 (crc32_no_comp, too). |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.5: |
| ====================================================================== |
| |
| * Update for TQM board defaults: |
| disable clocks_in_mhz, enable boot count limit |
| |
| * Removed tools/gdb from "make all" target. Added make target "gdbtools" |
| in toplevel directory instead. Removed astest.c from tools/gdb because |
| it is no longer relevant. |
| |
| * Fix PCI support for MPC5200 / IceCube Board |
| |
| * Map ISP1362 USB OTG controller for NSCU board |
| |
| * Patch by Brad Parker, 02 Aug 2003: |
| fix sc520_cdp problems |
| |
| * Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements) |
| |
| * Allow erase command to cross flash bank boundaries |
| |
| * Patch by Scott McNutt, 21 Jul 2003: |
| Add support for LynuxWorks Kernel Downloadable Images (KDIs). |
| Both LynxOS and BlueCat linux KDIs are supported. |
| |
| * Patch by Richard Woodruff, 25 Jul 2003: |
| use more reliable reset for OMAP/925T |
| |
| * Patch by Nye Liu, 25 Jul 2003: |
| fix typo in mpc8xx.h |
| |
| * Patch by Richard Woodruff, 24 Jul 2003: |
| Fixes for cmd_nand.c: |
| - Fixed null dereferece which could result in incorrect ECC values. |
| - Added support for devices with no Ready/Busy signal hooked up. |
| - Added OMAP1510 read/write protect handling. |
| - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock |
| for non-JFFS2. |
| - Switched default ECC to be JFFS2. |
| |
| * Allow crc32 to be used at address 0x000 |
| |
| * Provide consistent interface to standalone applications to access |
| the 'global_data' structure |
| Provide a doc/README.standalone more useful to users/developers. |
| |
| * Make IceCube MGT5100 FEC driver work |
| |
| * Implement new mechanism to export U-Boot's functions to standalone |
| applications: instead of using (PPC-specific) system calls we now |
| use a jump table; please see doc/README.standalone for details |
| |
| * Patch by Dave Westwood, 24 Jul 2003: |
| added support for Unity OS (a proprietary OS) |
| |
| * Patch by Detlev Zundel, 23 Jul 2003: |
| add "imls" command to print flash table of contents |
| |
| * Fix cold boot detection for log buffer reset |
| |
| * Return error for invalid length specifiers with "cp.X" etc. |
| |
| * Fix startup problem on MIPS |
| |
| * Allow for CONFIG_SPLASH_SCREEN even when no explicit |
| bitmap support is configured |
| |
| * Patch by Bill Hargen, 18 Jul 2003: |
| - fix endinaness problem in cpu/mpc824x/drivers/i2c/i2c1.c |
| |
| * Patch by Denis Peter, 18 Jul 2003: |
| - fix memory configuration for MIP405T |
| - fix printout of baudrate for "loadb <loadaddr> <baudrate>" |
| |
| * Cleanup of TQM82xx configurations; use "official" board types |
| to make selection easier. |
| |
| * Patch by Martin Krause, 17 Jul 2003: |
| add delay to get I2C working with "imm" command and s3c24x0_i2c.c |
| |
| * Patch by Richard Woodruff, 17 July 03: |
| - Fixed bug in OMAP1510 baud rate divisor settings. |
| |
| * Patch by Nye Liu, 16 July 2003: |
| MPC860FADS fixes: |
| - add MPC86xADS support (uses MPC86xADS.h) |
| - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T) |
| o PLPRCR changes |
| o BRG changes (EXTAL/XTAL restricted to 10MHz) |
| o don't trust gclk() software measurement by default, depend on |
| CONFIG_8xx_GCLK_FREQ |
| - add DRAM SIMM not installed detection |
| - use more "correct" SDRAM initialization sequence |
| - allow different SDRAM sizes (8xxADS has 8M) |
| - default DER is 0 |
| - remove unused MAMR defines from FADS860T.h (all done in fads.c) |
| - rename MAMR/MBMR defines to be more consistent. Should eventually |
| be merged into MxMR to better reflect the PowerQUICC datasheet. |
| |
| * Patch by Yuli Barcohen, 16 Jul 2003: |
| support new Motorola PQ2FADS-ZU evaluation board which replaced |
| MPC8260ADS and MPC8266ADS |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.4: |
| ====================================================================== |
| |
| * Add support for IceCube board (with MGT5100 and MPC5200 CPUs) |
| |
| * Add support for MGT5100 and MPC5200 processors |
| |
| * Patch by Lutz Dennig, 15 Jul 2003: |
| update for R360MPI board |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.3: |
| ====================================================================== |
| |
| * Patches by Kshitij, 04 Jul 2003 |
| - added support for arm925t cpu core |
| - added support for TI OMAP 1510 Innovator Board |
| |
| * Patches by Martin Krause, 14 Jul 2003: |
| - add I2C support for s3c2400 systems (trab board) |
| - (re-) add "ping" to command table |
| |
| * Fix handling of "slow" POST routines |
| |
| * Patches by Yuli Barcohen, 13 Jul 2003: |
| - Correct flash and JFFS2 support for MPC8260ADS |
| - fix PVR values and clock generation for PowerQUICC II family |
| (8270/8275/8280) |
| |
| * Patch by Bernhard Kuhn, 08 Jul 2003: |
| - add support for M68K targets |
| |
| * Patch by Ken Chou, 3 Jul: |
| - Fix PCI config table for A3000 |
| - Fix iobase for natsemi.c |
| (PCI_BASE_ADDRESS_0 is the IO base register for DP83815) |
| |
| * Allow to enable "slow" POST routines by key press on power-on |
| * Fix temperature dependend switching of LCD backlight on LWMON |
| * Tweak output format for LWMON |
| |
| * Patch by Stefan Roese, 11 Jul 2003: |
| - Fix bug in CONFIG_VERSION_VARIABLE. |
| - AR405 config updated. |
| - OCRTC/ORSG: bsp command added. |
| - ASH405 bsp update. |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.2: |
| ====================================================================== |
| |
| * Add support for NSCU board |
| |
| * Add support for TQM823M, TQM850M, TQM855M and TQM860M modules |
| |
| * Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML |
| mirror bit flash on TQM8xxM modules |
| |
| * Patch by Kenneth Johansson, 30 Jun 2003: |
| get rid of MK_CMD_ENTRY macro; update doc/README.command |
| |
| * Patch by Seb James, 30 Jun 2003: |
| Improve documentation of I2C configuration in README |
| |
| * Fix problems with previous log buffer "fixes" |
| |
| * Fix minor help text issues |
| |
| * "log append" did not append a newline |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.1: |
| ====================================================================== |
| |
| * Fix some missing commands, cleanup header files |
| (autoscript, bmp, bsp, fat, mmc, nand, portio, ...) |
| |
| * Rewrite command lookup and help command (fix problems with bubble |
| sort when sorting command name list). Minor cleanup here and there. |
| |
| * Merge from "stable branch", tag LABEL_2003_06_28_1800-stable: |
| - Allow to call sysmon function interactively |
| - PIC on LWMON board needs delay after power-on |
| - Add missing RSR definitions for MPC8xx |
| - Improve log buffer handling: guarantee clean reset after power-on |
| - Add support for EXBITGEN board (aka "genie") |
| - Add support for SL8245 board |
| |
| * Code cleanup: |
| - remove trailing white space, trailing empty lines, C++ comments, etc. |
| - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c) |
| |
| * Patches by Kenneth Johansson, 25 Jun 2003: |
| - major rework of command structure |
| (work done mostly by Michal Cendrowski and Joakim Kristiansen) |
| |
| ====================================================================== |
| Changes for U-Boot 0.4.0: |
| ====================================================================== |
| |
| * Patches by Robert Schwebel, 26 Jun 2003: |
| - csb226 configuration updated |
| - credits for logodl port updated |
| - innokom configuration updated |
| - logodl tree update, still with coding style inconsistencies |
| - added OCM for ppc405 warning to README |
| |
| * Patch by Pantelis Antoniou, 25 Jun 2003: |
| update NetVia with V2 board support |
| |
| * Header file cleanup for ARM |
| |
| * Patch by Murray Jensen, 24 Jun 2003: |
| - make sure to use only U-boot provided header files |
| - fix problems with ".rodata.str1.4" section as used by GCC-3.x |
| |
| * Patch by Stefan Roese, 24 Jun 2003: |
| - Update esd ASH405 board files. |
| - Update esd DASA_SIM config file. |
| - Add ping command to some esd boards. |
| |
| * Patch by Yuli Barcohen, 23 Jun 2003: |
| Update for MPC8260ADS board |
| |
| * Patch by Murray Jensen, 23 Jun 2003: |
| - cleanup of GCC 3.x compiler warnings |
| |
| * Patch by Rune Torgersen, 4 Jun 2003: |
| add large memory support for MPC8266ADS board |
| |
| * Patch by Richard Woodruff, 19 June 03: |
| - Enabled standard u-boot device abstraction for ARM |
| - Enabled console device for ARM |
| - Initilized bi_baudrate for ARM |
| |
| * Patch by Bill Hargen, 23 Apr 2003: |
| fix byte order for 824x I2C addresses (write op) |
| |
| * Patch by Murray Jensen, 20 Jun 2003: |
| - hymod update |
| - cleanup (especially for gcc-3.x compilers) |
| |
| * Patch by Tom Guilliams, 20 Jun 2003: |
| added CONFIG_750FX support for IBM 750FX processors |
| |
| * Patch by Devin Crumb, 02 Apr 2003: |
| Fix clock divider rounding problem in drivers/serial.c |
| |
| * Patch by Richard Woodruff, 19 June 03: |
| - Fixed smc91c111 driver to sync with the u-boot environment |
| (driver/smc91c111.c). |
| - Added eth_init error return check in NetLoop (net/net.c). |
| |
| * Patch by Ken Chou, 19 June 2003: |
| Added support for A3000 SBC board (Artis Microsystems Inc.) |
| |
| * Patches by Murray Jensen, 17 Jun 2003: |
| - Hymod board database mods: add "who" field and new xilinx chip types |
| - provide new "init_cmd_timeout()" function so code external to |
| "common/main.c" can use the "reset_cmd_timeout()" function before |
| entering the main loop |
| - add DTT support for adm1021 (new file dtt/adm1021.c; config |
| slightly different. see include/configs/hymod.h for an example |
| (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and |
| CFG_DTT_ADM1021 defined) |
| - add new "eeprom_probe()" function which has similar args and |
| behaves in a similar way to "eeprom_read()" etc. |
| - add 8260 FCC ethernet loopback code (new "eth_loopback_test()" |
| function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST) |
| - gdbtools copyright update |
| - ensure that set_msr() executes the "sync" and "isync" instructions |
| after the "mtmsr" instruction in cpu/mpc8260/interrupts.c |
| - 8260 I/O ports fix: Open Drain should be set last when configuring |
| - add SIU IRQ defines for 8260 |
| - allow LDSCRIPT override and OBJCFLAGS initialization: change to |
| config.mk to allow board configurations to override the GNU |
| linker script, selected via the LDSCRIPT, make variable, and to |
| give an initial value to the OBJCFLAGS make variable |
| - 8260 i2c enhancement: |
| o correctly extends the timeout depending on the size of all |
| queued messages for both transmit and receive |
| o will not continue with receive if transmit times out |
| o ensures that the error callback is done for all queued tx |
| and rx messages |
| o correctly detects both tx and rx timeouts, only delivers one to |
| the callback, and does not overwrite an earlier error |
| o logic in i2c_probe now correct |
| - add "vprintf()" function so that "panic()" function can be |
| technically correct |
| - many Hymod board changes |
| |
| * Patches by Robert Schwebel, 14 Jun 2003: |
| - add support for Logotronic DL datalogger board |
| - cleanup serial line after kermit binary download |
| - add debugX macro (debug level support) |
| - update mach-types.h to latest arm.linux.org.uk master list. |
| |
| * Patches by David Müller, 12 Jun 2003: |
| - rewrite of the S3C24X0 register definitions stuff |
| - "driver" for the built-in S3C24X0 RTC |
| |
| * Patches by Yuli Barcohen, 12 Jun 2003: |
| - Add MII support and Ethernet PHY initialization for MPC8260ADS board |
| - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset |
| configuration word supplied by FPGA on some MPC8260ADS boards |
| |
| * Patch by Pantelis Antoniou, 10 Jun 2003: |
| Unify status LED interface |
| |
| * Add support for DS12887 RTC; add RTC support for ATC board |
| |
| * Patch by Nicolas Lacressonniere, 11 Jun 2003: |
| Modifications for Atmel AT91RM9200DK ARM920T based development kit |
| - Add Atmel DataFlash support for reading and writing. |
| - Add possibility to boot a Linux from DataFlash with BOOTM command. |
| - Add Flash detection on Atmel AT91RM9200DK |
| (between Atmel AT49BV1614 and AT49BV1614A flashes) |
| - Replace old Ethernet PHY layer functions |
| - Change link address |
| |
| * Patch by Frank Smith, 9 Jun 2003: |
| use CRIT_EXCEPTION for machine check on 4xx |
| |
| * Patch by Detlev Zundel, 13 Jun 2003: |
| added implementation of the "carinfo" command in cmd_immap.c |
| |
| * Fix CONFIG_NET_MULTI support in include/net.h |
| |
| * Patches by Kyle Harris, 13 Mar 2003: |
| - Add FAT partition support |
| - Add command support for FAT |
| - Add command support for MMC |
| ---- |
| - Add Intel PXA support for video |
| - Add Intel PXA support for MMC |
| ---- |
| - Enable MMC and FAT for lubbock board |
| - Other misc changes for lubbock board |
| |
| * Patch by Robert Schwebel, April 02, 2003: |
| fix for SMSC91111 driver |
| |
| * Patch by Vladimir Gurevich, 04 Jun 2003: |
| make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option |
| |
| * Patch by Stefan Roese, 05 Jun 2003: |
| - PPC4xx: Fix bug for initial stack in data cache as pointed out by |
| Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in |
| data cache can be used even if the chip select is in use. |
| - CFG_RX_ETH_BUFFER added to set the ethernet receive buffer count |
| (see README for further description). |
| - Changed config files of CONFIG_EEPRO100 boards to use the |
| CFG_RX_ETH_BUFFER define. |
| |
| * Add support for RMU board |
| |
| * Add support for TQM862L at 100/50 MHz |
| |
| * Patch by Pantelis Antoniou, 02 Jun 2003: |
| major reconstruction of networking code; |
| add "ping" support (outgoing only!) |
| |
| * Patch by Denis Peter, 04 June 2003: |
| add support for the MIP405T board |
| |
| * Patches by Udi Finkelstein, 2 June 2003: |
| - Added support for custom keyboards, initialized by defining a |
| board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD . |
| - Added support for the RBC823 board. |
| - cpu/mpc8xx/lcd.c now automatically calculates the |
| Horizontal Pixel Count field. |
| |
| * Fix alignment problem in BOOTP (dhcp_leasetime option) |
| [pointed out by Nicolas Lacressonnière, 2 Jun 2003] |
| |
| * Patch by Mark Rakes, 14 May 2003: |
| add support for Intel e1000 gig cards. |
| |
| * Patch by Nye Liu, 3 Jun 2003: |
| fix critical typo in MAMR definition (include/mpc8xx.h) |
| |
| * Fix requirement to align U-Boot image on 16 kB boundaries on PPC. |
| |
| * Patch by Klaus Heydeck, 2 Jun 2003 |
| Minor changes for KUP4K configuration |
| |
| * Patch by Marc Singer, 29 May 2003: |
| Fixed rarp boot method for IA32 and other little-endian CPUs. |
| |
| * Patch by Marc Singer, 28 May 2003: |
| Added port I/O commands. |
| |
| * Patch by Matthew McClintock, 28 May 2003 |
| - cpu/mpc824x/start.S: fix relocation code when booting from RAM |
| - minor patches for utx8245 |
| |
| * Patch by Daniel Engström, 28 May 2003: |
| x86 update |
| |
| * Patch by Dave Ellis, 9 May 2003 + 27 May 2003: |
| add nand flash support to SXNI855T configuration |
| fix/extend nand flash support: |
| - fix 'nand erase' command so does not erase bad blocks |
| - fix 'nand write' command so does not write to bad blocks |
| - fix nand_probe() so handles no flash detected properly |
| - add doc/README.nand |
| - add .jffs2 and .oob options to nand read/write |
| - add 'nand bad' command to list bad blocks |
| - add 'clean' option to 'nand erase' to write JFFS2 clean markers |
| - make NAND read/write faster |
| |
| * Patch by Rune Torgersen, 23 May 2003: |
| Update for MPC8266ADS board |
| |
| * Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length |
| instead CFG_MONITOR_LEN is now only used to determine _at_compile_ |
| _time_ (!) if the environment is embedded within the U-Boot image, |
| or in a separate flash sector. |
| |
| * Cleanup CFG_DER #defines in config files (wd maintained only) |
| |
| * Fix data abort exception handling for arm920t CPU |
| |
| * Fix alignment problems with flash driver for TRAB board |
| |
| * Patch by Donald White, 21 May 2003: |
| fix calculation of base address in pci_hose_config_device() |
| |
| * Fix bug in command line parsing: "cmd1;cmd2" is supposed to always |
| execute "cmd2", even if "cmd1" fails. Note that this is different |
| to "run var1 var2" where the contents of "var2" will NOT be |
| executed when a command in "var1" fails. |
| |
| * Add zero-copy ramdisk support (requires corresponding kernel support!) |
| |
| * Patch by Kyle Harris, 20 May 2003: |
| In preparation for an ixp port, rename cpu/xscale and arch-xscale |
| into cpu/pxa and arch-pxa. |
| |
| * Patch by Stefan Roese, 23 May 2003: |
| - IBM PPC405EP port added. |
| - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not |
| UART0) is used as default U-Boot console. PPC4xx only! |
| - esd ASH405 board added (PPC405EP based). |
| - BUBINGA405EP board added (PPC405EP based - IBM Eval Board). |
| - esd CPCI405AB board added. |
| - esd PMC405 board added. |
| - Update of some esd boards. |
| |
| * Patch by Denis Peter, 19 Mai 2003: |
| add support for the MIP405-3 board |
| |
| * Patch by Dave Ellis, 22 May 2003: |
| Fix problem with only partially cleared .bss segment |
| |
| * Patch by Rune Torgersen, 12 May 2003: |
| get PCI to work on a MPC8266ADS board; incorporate change to |
| cpu/mpc8260/pci.c to enable overrides of PCI memory parameters |
| |
| * Patch by Nye Liu, 1 May 2003: |
| minor patches for the FADS8xx |
| |
| * Patch by Thomas Schäfer, 28 Apr 2003: |
| Fix SPD handling for 256 ECC DIMM on Walnut |
| |
| * Add support for arbitrary bitmaps for TRAB's VFD command; |
| allow to pass boot bitmap addresses in environment variables; |
| allow for zero boot delay |
| |
| * Patch by Christian Geißinger, 19 May 2002: |
| On TRAB: wait until the dummy byte has been completely sent |
| |
| * Patch by David Updegraff, 22 Apr 2003: |
| update for CrayL1 board |
| |
| * Patch by Pantelis Antoniou, 21 Apr 2003: |
| add boot support for ARTOS (a proprietary OS) |
| |
| * Patch by Steven Scholz, 11 Apr 2003: |
| Add support for RTC DS1338 |
| |
| * Patch by Rod Boyce, 24 Jan 2003: |
| Fix counting of extended partitions in diskboot command |
| |
| * Patch by Christophe Lindheimer, 20 May 2003: |
| allow the use of CFG_LOADS when CFG_NO_FLASH is set |
| |
| * Fix SDRAM timing on Purple board |
| |
| * Add support for CompactFlash on ATC board |
| (includes support for Intel 82365 and compatible PC Card controllers, |
| and Yenta-compatible PCI-to-CardBus controllers) |
| |
| * Patch by Mathijs Haarman, 08 May 2003: |
| Add lan91c96 driver (tested on Lubbock and custom PXA250 board only) |
| |
| * Fix problem with usage of "true" (undefined in current versions of bfd.h) |
| |
| * Add support for Promess ATC board |
| |
| * Patch by Keith Outwater, 28 Apr 2003: |
| - Miscellaneous corrections and additions to GEN860T board specific code. |
| - Added GEN860_SC variant to GEN860T. |
| - Miscellaneous corrections to GEN860T documentation. |
| - Correct duplicate entry in U-Boot CREDITS file. |
| - Add GEN860T_SC entry in MAINTAINERS file. |
| - Update CREDITS file with GEN860T_SC info. |
| |
| * Update Smiths Aerospace addresses in MAINTAINERS file |
| |
| * Fix error handling in hush's version of "run" command |
| |
| * LWMON extensions: |
| - Splashscreen support |
| - modem support |
| - sysmon support |
| - temperature dependend enabling of LCD |
| |
| * Allow booting from old "PPCBoot" disk partitions |
| |
| * Add support for TQM8255 Board / MPC8255 CPU |
| |
| ====================================================================== |
| Changes for U-Boot 0.3.1: |
| ====================================================================== |
| |
| * Make sure Block Lock Bits get cleared in R360MPI flash driver |
| |
| * MPC823 LCD driver: Fill color map backwards, to allow for steady |
| display when Linux takes over |
| |
| * Patch by Erwin Rol, 27 Feb 2003: |
| Add support for RTEMS (this time for real). |
| |
| * Add support for "bmp info" and "bmp display" commands to load |
| bitmap images; this can be used (for example in a "preboot" |
| command) to display a splash screen very quickly after poweron. |
| |
| * Add support for 133 MHz clock on INCA-IP board |
| |
| * Patch by Lutz Dennig, 10 Apr 2003: |
| Update for R360MPI board |
| |
| * Add new meaning to "autostart" environment variable: |
| If set to "no", a standalone image passed to the |
| "bootm" command will be copied to the load address |
| (and eventually uncompressed), but NOT be started. |
| This can be used to load and uncompress arbitrary |
| data. |
| |
| * Patch by Stefan Roese, 10 Apr 2003: |
| Changed DHCP client to use IP address from server option field #54 |
| from the OFFER packet in the server option field #54 in the REQUEST |
| packet. This fixes a problem using a Windows 2000 DHCP server, |
| where the DHCP-server is not the TFTP-server. |
| |
| * Set max brightness for MN11236 displays on TRAB board |
| |
| * Add support for TQM862L modules |
| |
| ====================================================================== |
| Changes for U-Boot 0.3.0: |
| ====================================================================== |
| |
| * Patch by Arun Dharankar, 4 Apr 2003: |
| Add IDMA example code (tested on 8260 only) |
| |
| * Add support for Purple Board (MIPS64 5Kc) |
| |
| * Add support for MIPS64 5Kc CPUs |
| |
| * Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS |
| |
| * Patch by Denis Peter, 04 Apr 2003: |
| - update MIP405-4 board |
| |
| * Patch by Stefan Roese, 4 Apr 2003: |
| - U-Boot version environment variable "ver" added |
| (CONFIG_VERSION_VARIABLE). |
| - Changed PPC405GPr version from A to B. |
| - Changed CPCI405 to use CTS instead of DSR on PPC405 UART1. |
| |
| * Patches by Denis Peter, 03 April 2003: |
| - fix PCI IRQs on MPL boards |
| - fix two more un-relocated pointer problems |
| |
| * Fix behaviour of "run" command: |
| - print error message iv variable does not exist |
| - terminate processing of arguments in case of error |
| |
| * Patches by Peter Figuli, 10 Mar 2003 |
| - Add support for BTUART on PXA platform |
| - Add support for WEP EP250 (PXA) board |
| |
| * Fix flash problems on INCA-IP; add tool to allow bruning images to |
| flash using a BDI2000 |
| |
| * Implement fix for I2C Edge Conditions problem for all boards that |
| use the bit-banging driver (common/soft_i2c.c) |
| |
| * Patch by Martin Winistoerfer, 23 Mar 2003 |
| - Add port to MPC555/556 microcontrollers |
| - Add support for cmi customer board with |
| Intel 28F128J3A, 28F320J3A or 28F640J3A flash. |
| |
| * Patch by Rick Bronson, 28 Mar 2003: |
| - fix common/cmd_nand.c |
| |
| * Patch by Arun Dharankar, 24 Mar 2003: |
| - add threads / scheduler example code |
| |
| * Add patches by Robert Schwebel, 31 Mar 2003: |
| - add ctrl-c support for kermit download |
| - align bdinfo output on ARM |
| - csb226 board: bring in sync with innokom/memsetup.S |
| - csb226 board: fix MDREFR handling |
| - misc doc fixes / extensions |
| - innokom board: cleanup, MDREFR fix in memsetup.S, config update |
| - add BOOT_PROGRESS to armlinux.c |
| |
| * Add CPU ID, version, and clock speed for INCA-IP |
| |
| * Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board: |
| - fix SRAM and SDRAM memory sizing |
| - add status LED support |
| - add MAC address for second (SCC1) ethernet port |
| |
| * Update default environment for TQM8260 board |
| |
| * Patch by Rick Bronson, 16 Mar 2003: |
| - Add NAND flash support for reading, writing, and erasing NAND |
| flash (certain forms of which are called SmartMedia). |
| - Add support for Atmel AT91RM9200DK ARM920T based development kit. |
| |
| * Patches by Robert Schwebel, 19 Mar 2003: |
| - use arm-linux-gcc as default compiler for ARM |
| - fix i2c fixup code |
| - fix missing baudrate setting |
| - added $loadaddr / CFG_LOAD_ADDR support to loadb |
| - moved "ignoring trailing characters" _before_ u-boot wants to |
| print out diagnostics messages; removes bogus characters at the |
| end of transmission |
| |
| * Patch by John Zhan, 18 Mar 2003: |
| Add support for SinoVee Microsystems SC8xx boards |
| |
| * Patch by Rolf Offermanns, 21 Mar 2003: |
| ported the dnp1110 related changes from the current armboot cvs to |
| current u-boot cvs. smc91111 does not work. problem marked in |
| smc91111.c, grep for "FIXME". |
| |
| * Patch by Brian Auld, 25 Mar 2003: |
| Add support for STM flash chips on ebony board |
| |
| * Add PCI support for MPC8250 Boards (PM825 module) |
| |
| * Patch by Stefan Roese, 25 Mar 2003: |
| - PCI405 update. |
| |
| * Patch by Stefan Roese, 20 Mar 2003: |
| - CPCI4052 update (support for revision 3). |
| - Set edge conditioning circuitry on PPC405GPr for compatibility |
| to existing PPC405GP designs. |
| - Clip udiv to 5 bits on PPC405 (serial.c). |
| |
| * Extend INCAIP board support: |
| - add automatic RAM size detection |
| - add "bdinfo" command |
| - pass flash address and size to Linux kernel |
| - switch to 150 MHz clock |
| |
| * Avoid flicker on the TRAB's VFD by synchronizing the enable with |
| the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100 |
| boards, version 153 for Rev. 200 boards). |
| |
| * Patch by Vladimir Gurevich, 12 Mar 2003: |
| Fix relocation problem of statically initialized string pointers |
| in common/cmd_pci.c |
| |
| * Patch by Kai-Uwe Blöm, 12 Mar 2003: |
| Cleanup & bug fixes for JFFS2 code: |
| - the memory mangement was broken. It caused havoc on malloc by |
| writing beyond the block boundaries. |
| - the length calculation for files was wrong, sometimes resulting |
| in short file reads. |
| - data copying now optionally takes fragment version numbers into |
| account, to avoid copying from older data. |
| See doc/README.JFFS2 for details. |
| |
| * Patch by Josef Wagner, 12 Mar 2003: |
| - 16/32 MB and 50/80 MHz support with auto-detection for IP860 |
| - ETH05 and BEDBUG support for CU824 |
| - added support for MicroSys CPC45 |
| - new BOOTROM/FLASH0 and DOC base for PM826 |
| |
| * Patch by Robert Schwebel, 12 Mar 2003: |
| Fix the chpart command on innokom board |
| |
| * Name cleanup: |
| mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h |
| s/PPCBoot/U-Boot/ in some files |
| s/pImage/uImage/ in some files |
| |
| * Patch by Detlev Zundel, 15 Jan 2003: |
| Fix '' command line quoting |
| |
| * Patch by The LEOX team, 19 Jan 2003: |
| - add support for the ELPT860 board |
| - add support for Dallas ds164x RTC |
| |
| * Patches by David Müller, 31 Jan 2003: |
| - minimal setup for CardBus bridges |
| - add EEPROM read/write support in the CS8900 driver |
| - add support for the builtin I2C controller in the Samsung s3c24x0 chips |
| - add support for MPL's VCMA9 (Samsung s3c2410 based) board |
| |
| * Patch by Steven Scholz, 04 Feb 2003: |
| add support for RTC DS1307 |
| |
| * Patch by Reinhard Meyer, 5 Feb 2003: |
| fix PLPRCR/SCCR init sequence on 8xx to allow for |
| changes of EBDF by software |
| |
| * Patch by Vladimir Gurevich, 07 Feb 2003: |
| "API-compatibility patch" for 4xx I2C driver |
| |
| * TRAB fixes / extensions: |
| - Restore VFD brightness as saved in environment |
| - add support for Fujitsu flashes |
| - make sure both buzzers are turned off (drive low level) |
| |
| * Patches by Robert Schwebel, 06 Mar 2003: |
| - fix bug in BOOTP code (must use NetCopyIP) |
| - update of CSB226 port |
| - clear BSS segment on XScale |
| - added support for i2c_init_board() function |
| - update to the Innokom plattform |
| |
| * Extend support for redundand environments for configurations where |
| environment size < sector size |
| |
| * Patch by Rune Torgersen, 13 Feb 2003: |
| Add support for Motorola MPC8266ADS board |
| |
| * Patch by Kyle Harris, 19 Feb 2003: |
| patches for the Intel lubbock board: |
| memsetup.S - general cleanup (based on Robert's csb226 code) |
| flash.c - overhaul, actually works now |
| lubbock.c - fix init funcs to return proper value |
| |
| * Patch by Kenneth Johansson, 26 Feb 2003: |
| - Fixed off by one in RFTA calculation. |
| - No need to abort when LDF is lower than we can program it's only |
| minimum timing so clamp it to what we can do. |
| - Takes function pointer to function for reading the spd_nvram. Usefull |
| for faking data or hardcode a module without the nvram. |
| - fix other user for above change |
| - fix some comments. |
| |
| * Patches by Brian Waite, 26 Feb 2003: |
| - fix port for evb64260 board |
| - fix PCI for evb64260 board |
| - fix PCI scan |
| |
| * Patch by Reinhard Meyer, 1 Mar 2003: |
| Add support for EMK TOP860 Module |
| |
| * Patch by Yuli Barcohen, 02 Mar 2003: |
| Add SPD EEPROM support for MPC8260ADS board |
| |
| * Patch by Robert Schwebel, 21 Jan 2003: |
| - Add support for Innokom board |
| - Don't complain if "install" fails |
| - README cleanup (remove duplicated lines) |
| - Update PXA header files |
| |
| * Add documentation for existing POST code (doc/README.POST) |
| |
| * Patch by Laudney Ren, 15 Jan 2003: |
| Fix handling of redundand environment in "tools/envcrc.c" |
| |
| * Patch by Detlev Zundel, 28 Feb 2003: |
| Add bedbug support for 824x systems |
| |
| * Add support for 16 MB flash configuration of TRAB board |
| |
| * Patch by Erwin Rol, 27 Feb 2003: |
| Add support for RTEMS |
| |
| * Add image information to README |
| |
| * Patch by Stefan Roese, 18 Feb 2003: |
| CPCIISER4 configuration updated. |
| |
| * Patch by Stefan Roese, 17 Feb 2003: |
| Fixed bug in ext. serial clock setup on PPC405 (since PPC440 port). |
| |
| * Patch by Stefan Roese, 13 Feb 2003: |
| Add "pcidelay" environment variable (in ms, enabled via |
| CONFIG_PCI_BOOTDELAY). |
| PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after |
| RST# to respond to configuration cycles (33MHz -> 1s). |
| |
| * Fix dual PCMCIA slot support (when running with just one |
| slot populated) |
| |
| * Add VFD type detection to trab board |
| |
| * extend drivers/cs8900.c driver to synchronize ethaddr environment |
| variable with value in the EEPROM |
| |
| * Patch by Stefan Roese, 10 Feb 2003: |
| Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c) |
| |
| * Add support for MIPS32 4Kc CPUs |
| |
| * Add support for INCA-IP Board |
| |
| ====================================================================== |
| Changes for U-Boot 0.2.2: |
| ====================================================================== |
| |
| * Add dual ethernet support on PM826 |
| |
| * Add support for LXT971 PHY on PM826 |
| |
| * Patch by Tord Andersson, 16 Jan 2003: |
| Fix flash sector count for TQM8xxL |
| |
| * Fix I2C EEPROM problem on ICU862 board (would only write the first |
| 16 bytes out of each 32 byte block) |
| |
| ====================================================================== |
| Changes for U-Boot 0.2.1: |
| ====================================================================== |
| |
| * Add support for V37 board |
| (patch by Jón Benediktsson, 11 Dec 2002) |
| |
| * Update baudrate in bd_info when it gets changed |
| |
| * Add watchdog trigger points while waiting for serial port |
| (so far only 8xx -- needed on LWMON with 100ms watchdog) |
| |
| * Improve command line tool to access the U-Boot's environment |
| (figuration of the utility, using a config file) |
| |
| * Add single quote support for (old) command line parser |
| |
| * Switch LWMON board default config from FRAM to EEPROM; |
| in POST, EEPROM shows up on 8 addresses |
| |
| ====================================================================== |
| Changes for U-Boot 0.2.0: |
| ====================================================================== |
| |
| * Use 1-byte-read instead of -write for iprobe() function |
| Add i2c commands to PM826 config |
| |
| * extend I2C POST code: check for list on known addresses |
| |
| * Improve log buffer code; use "loglevel" to decide which messages |
| to log on the console, too (like in Linux); get rid of "logstart" |
| |
| * Add command line tool to access the U-Boot's environment |
| (board-specific for TRAB now, to be fixed later) |
| |
| * Patch by Hans-Joerg Frieden, 06 Dec 2002 |
| Fix misc problems with AmigaOne support |
| |
| * Patch by Chris Hallinan, 3 Dec 2002: |
| minor cleanup to the MPC8245 EPIC driver |
| |
| * Patch by Pierre Aubert , 28 Nov 2002 |
| Add support for external (SIU) interrupts on MPC8xx |
| |
| * Patch by Pierre Aubert , 28 Nov 2002 |
| Fix nested syscalls bug in standalone applications |
| |
| * Patch by David Müller, 27 Nov 2002: |
| fix output of "pciinfo" command for CardBus bridge devices. |
| |
| * Fix bug in TQM8260 board detection - boards got stuck when board ID |
| was not readable |
| |
| * Add LED indication for IDE activity on KUP4K board |
| |
| * Fix startup problems with VFD display on TRAB |
| |
| * Patch by Pierre Aubert, 20 Nov 2002 |
| Add driver for Epson SED13806 graphic controller. |
| Add support for BMP logos in cfb_console driver. |
| |
| * Added support for both PCMCIA slots (at the same time!) on MPC8xx |
| |
| * Patch by Rod Boyce, 21 Nov 2002: |
| fix PCMCIA on MBX8xx board |
| |
| * Patch by Pierre Aubert , 21 Nov 2002 |
| Add CFG_CPM_POST_WORD_ADDR to make the offset of the |
| bootmode word in DPRAM configurable |
| |
| * Patch by Daniel Engström, 18 Nov 2002: |
| Fixes for x86 port (mostly strings issues) |
| |
| * Patch by Ken Chou, 18 Nov 2002: |
| Fix for natsemi NIC cards (DP83815) |
| |
| * Patch by Pierre Aubert, 19 Nov 2002: |
| fix a bug for the MII configuration, and some warnings |
| |
| * Patch by Thomas Frieden, 13 Nov 2002: |
| Add code for AmigaOne board |
| (preliminary merge to U-Boot, still WIP) |
| |
| * Patch by Jon Diekema, 12 Nov 2002: |
| - Adding URL for IEEE OUI lookup |
| - Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED |
| being defined. |
| - In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and |
| root-on-nfs macros are designed to switch how the default boot |
| method gets defined. |
| |
| * Patch by Daniel Engström, 13 Nov 2002: |
| Add support for i386 architecture and AMD SC520 board |
| |
| * Patch by Pierre Aubert, 12 Nov 2002: |
| Add support for DOS filesystem and booting from DOS floppy disk |
| |
| * Patch by Jim Sandoz, 07 Nov 2002: |
| Increase number of network RX buffers (PKTBUFSRX in |
| "include/net.h") for EEPRO100 based boards (especially SP8240) |
| which showed "Receiver is not ready" errors when U-Boot was |
| processing the receive buffers slower than the network controller |
| was filling them. |
| |
| * Patch by Andreas Oberritter, 09 Nov 2002: |
| Change behaviour of NetLoop(): return -1 for errors, filesize |
| otherwise; return code 0 is valid an means no file loaded - in this |
| case the environment still gets updated! |
| |
| * Patches by Jon Diekema, 9 Nov 2002: |
| - improve ADC/DAC clocking on the SACSng board to align |
| the failing edges of LRCLK and SCLK |
| - sbc8260 configuration tweaks |
| - add status LED support for 82xx systems |
| - wire sspi/sspo commands into command handler; improved error |
| handlering |
| - add timestamp support and alternate memory test to the |
| SACSng configuration |
| |
| * Patch by Vince Husovsky, 7 Nov 2002: |
| Add "-n" to linker options to get rid of "Not enough room for |
| program headers" problem |
| |
| * Patch by David Müller, 05 Nov 2002 |
| Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ |
| so we can use an already existing name |
| |
| * Patch by Pierre Aubert, 05 Nov 2002 |
| Hardware relatied improvments in FDC boot code |
| |
| * Patch by Holger Schurig, 5 Nov 2002: |
| Make the PXA really change it's frequency |
| |
| * Patch by Pierre Aubert, 05 Nov 2002 |
| Add support for slave serial Spartan 2 FPGAs |
| |
| * Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet |
| drivers |
| |
| * Add support for log buffer which can be passed to Linux kernel's |
| syslog mechanism; used especially for POST results. |
| |
| * Patch by Klaus Heydeck, 31 Oct 2002: |
| Add initial support for kup4k board |
| |
| * Patch by Robert Schwebel, 04 Nov 2002: |
| - use watchdog to reset PXA250 systems |
| - added progress callbacks to (some of the) ARM code |
| - update for Cogent CSB226 board |
| |
| * Add support for FPS860 board |
| |
| * Patch by Guillaume Alexandre,, 04 Nov 2002: |
| Improve PCI access on 32-bits Compact PCI bus |
| |
| * Fix mdelay() on TRAB - this was still the debugging version with |
| seconds instead of ms. |
| |
| * Patch by Robert Schwebel, 1 Nov 2002: |
| XScale related cleanup (affects all ARM boards) |
| |
| * Cleanup of names and README. |
| |
| ====================================================================== |
| Notes for U-Boot 0.1.0: |
| ====================================================================== |
| |
| This is the initial version of "Das U-Boot", the Universal Boot Loader. |
| |
| It is based on version 2.0.0 (the "Halloween Release") of PPCBoot. |
| For information about the history of the project please see the |
| PPCBoot project page at http://sourceforge.net/projects/ppcboot |
| |
| ====================================================================== |