| /* |
| * Copyright (C) 2014 Atmel |
| * Bo Shen <voice.shen@atmel.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <asm/io.h> |
| #include <asm/arch/at91_common.h> |
| #include <asm/arch/at91_rstc.h> |
| #include <asm/arch/atmel_mpddrc.h> |
| #include <asm/arch/gpio.h> |
| #include <asm/arch/clk.h> |
| #include <asm/arch/sama5d3_smc.h> |
| #include <asm/arch/sama5d4.h> |
| #include <atmel_hlcdc.h> |
| #include <debug_uart.h> |
| #include <lcd.h> |
| #include <nand.h> |
| #include <version.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #ifdef CONFIG_NAND_ATMEL |
| static void sama5d4ek_nand_hw_init(void) |
| { |
| struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; |
| |
| at91_periph_clk_enable(ATMEL_ID_SMC); |
| |
| /* Configure SMC CS3 for NAND */ |
| writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) | |
| AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1), |
| &smc->cs[3].setup); |
| writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) | |
| AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3), |
| &smc->cs[3].pulse); |
| writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), |
| &smc->cs[3].cycle); |
| writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) | |
| AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) | |
| AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3)| |
| AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings); |
| writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | |
| AT91_SMC_MODE_EXNW_DISABLE | |
| AT91_SMC_MODE_DBW_8 | |
| AT91_SMC_MODE_TDF_CYCLE(3), |
| &smc->cs[3].mode); |
| |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 5, 0); /* D0 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 6, 0); /* D1 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 7, 0); /* D2 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 8, 0); /* D3 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 9, 0); /* D4 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 10, 0); /* D5 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 11, 0); /* D6 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 12, 0); /* D7 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 13, 0); /* RE */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 14, 0); /* WE */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 15, 1); /* NCS */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 16, 1); /* RDY */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 17, 1); /* ALE */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTC, 18, 1); /* CLE */ |
| } |
| #endif |
| |
| #ifdef CONFIG_CMD_USB |
| static void sama5d4ek_usb_hw_init(void) |
| { |
| at91_set_pio_output(AT91_PIO_PORTE, 11, 0); |
| at91_set_pio_output(AT91_PIO_PORTE, 12, 0); |
| at91_set_pio_output(AT91_PIO_PORTE, 10, 0); |
| } |
| #endif |
| |
| #ifdef CONFIG_LCD |
| vidinfo_t panel_info = { |
| .vl_col = 800, |
| .vl_row = 480, |
| .vl_clk = 33260000, |
| .vl_bpix = LCD_BPP, |
| .vl_tft = 1, |
| .vl_hsync_len = 5, |
| .vl_left_margin = 128, |
| .vl_right_margin = 0, |
| .vl_vsync_len = 5, |
| .vl_upper_margin = 23, |
| .vl_lower_margin = 22, |
| .mmio = ATMEL_BASE_LCDC, |
| }; |
| |
| /* No power up/down pin for the LCD pannel */ |
| void lcd_enable(void) { /* Empty! */ } |
| void lcd_disable(void) { /* Empty! */ } |
| |
| unsigned int has_lcdc(void) |
| { |
| return 1; |
| } |
| |
| static void sama5d4ek_lcd_hw_init(void) |
| { |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */ |
| |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */ |
| |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */ |
| |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 18, 0); /* LCDD18 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 19, 0); /* LCDD19 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 20, 0); /* LCDD20 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 21, 0); /* LCDD21 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 22, 0); /* LCDD22 */ |
| at91_pio3_set_a_periph(AT91_PIO_PORTA, 23, 0); /* LCDD23 */ |
| |
| /* Enable clock */ |
| at91_periph_clk_enable(ATMEL_ID_LCDC); |
| } |
| |
| #ifdef CONFIG_LCD_INFO |
| void lcd_show_board_info(void) |
| { |
| ulong dram_size, nand_size; |
| int i; |
| char temp[32]; |
| |
| lcd_printf("%s\n", U_BOOT_VERSION); |
| lcd_printf("2014 ATMEL Corp\n"); |
| lcd_printf("at91@atmel.com\n"); |
| lcd_printf("%s CPU at %s MHz\n", get_cpu_name(), |
| strmhz(temp, get_cpu_clk_rate())); |
| |
| dram_size = 0; |
| for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) |
| dram_size += gd->bd->bi_dram[i].size; |
| |
| nand_size = 0; |
| #ifdef CONFIG_NAND_ATMEL |
| for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++) |
| nand_size += nand_info[i]->size; |
| #endif |
| lcd_printf("%ld MB SDRAM, %ld MB NAND\n", |
| dram_size >> 20, nand_size >> 20); |
| } |
| #endif /* CONFIG_LCD_INFO */ |
| |
| #endif /* CONFIG_LCD */ |
| |
| #ifdef CONFIG_DEBUG_UART_BOARD_INIT |
| static void sama5d4ek_serial3_hw_init(void) |
| { |
| at91_pio3_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */ |
| at91_pio3_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */ |
| |
| /* Enable clock */ |
| at91_periph_clk_enable(ATMEL_ID_USART3); |
| } |
| |
| void board_debug_uart_init(void) |
| { |
| sama5d4ek_serial3_hw_init(); |
| } |
| #endif |
| |
| #ifdef CONFIG_BOARD_EARLY_INIT_F |
| int board_early_init_f(void) |
| { |
| #ifdef CONFIG_DEBUG_UART |
| debug_uart_init(); |
| #endif |
| return 0; |
| } |
| #endif |
| |
| int board_init(void) |
| { |
| /* adress of boot parameters */ |
| gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; |
| |
| #ifdef CONFIG_NAND_ATMEL |
| sama5d4ek_nand_hw_init(); |
| #endif |
| #ifdef CONFIG_LCD |
| sama5d4ek_lcd_hw_init(); |
| #endif |
| #ifdef CONFIG_CMD_USB |
| sama5d4ek_usb_hw_init(); |
| #endif |
| |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, |
| CONFIG_SYS_SDRAM_SIZE); |
| return 0; |
| } |
| |
| /* SPL */ |
| #ifdef CONFIG_SPL_BUILD |
| void spl_board_init(void) |
| { |
| #if CONFIG_SYS_USE_NANDFLASH |
| sama5d4ek_nand_hw_init(); |
| #endif |
| } |
| |
| static void ddr2_conf(struct atmel_mpddrc_config *ddr2) |
| { |
| ddr2->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM); |
| |
| ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 | |
| ATMEL_MPDDRC_CR_NR_ROW_14 | |
| ATMEL_MPDDRC_CR_CAS_DDR_CAS3 | |
| ATMEL_MPDDRC_CR_NB_8BANKS | |
| ATMEL_MPDDRC_CR_NDQS_DISABLED | |
| ATMEL_MPDDRC_CR_DECOD_INTERLEAVED | |
| ATMEL_MPDDRC_CR_UNAL_SUPPORTED); |
| |
| ddr2->rtr = 0x2b0; |
| |
| ddr2->tpr0 = (8 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET | |
| 3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET | |
| 3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | |
| 10 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | |
| 3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | |
| 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | |
| 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | |
| 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); |
| |
| ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | |
| 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET | |
| 25 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET | |
| 23 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET); |
| |
| ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET | |
| 2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET | |
| 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET | |
| 2 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET | |
| 8 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET); |
| } |
| |
| void mem_init(void) |
| { |
| struct atmel_mpddrc_config ddr2; |
| |
| ddr2_conf(&ddr2); |
| |
| /* Enable MPDDR clock */ |
| at91_periph_clk_enable(ATMEL_ID_MPDDRC); |
| at91_system_clk_enable(AT91_PMC_DDR); |
| |
| /* DDRAM2 Controller initialize */ |
| ddr2_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddr2); |
| } |
| |
| void at91_pmc_init(void) |
| { |
| u32 tmp; |
| |
| tmp = AT91_PMC_PLLAR_29 | |
| AT91_PMC_PLLXR_PLLCOUNT(0x3f) | |
| AT91_PMC_PLLXR_MUL(87) | |
| AT91_PMC_PLLXR_DIV(1); |
| at91_plla_init(tmp); |
| |
| at91_pllicpr_init(AT91_PMC_IPLL_PLLA(0x0)); |
| |
| tmp = AT91_PMC_MCKR_H32MXDIV | |
| AT91_PMC_MCKR_PLLADIV_2 | |
| AT91_PMC_MCKR_MDIV_3 | |
| AT91_PMC_MCKR_CSS_PLLA; |
| at91_mck_init(tmp); |
| } |
| #endif |