| if ARCH_SUNXI |
| |
| choice |
| prompt "Sunxi SoC Variant" |
| |
| config MACH_SUN4I |
| bool "sun4i (Allwinner A10)" |
| select CPU_V7 |
| select SUPPORT_SPL |
| |
| config MACH_SUN5I |
| bool "sun5i (Allwinner A13)" |
| select CPU_V7 |
| select SUPPORT_SPL |
| |
| config MACH_SUN6I |
| bool "sun6i (Allwinner A31)" |
| select CPU_V7 |
| select SUPPORT_SPL |
| |
| config MACH_SUN7I |
| bool "sun7i (Allwinner A20)" |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select SUPPORT_SPL |
| select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT |
| |
| config MACH_SUN8I |
| bool "sun8i (Allwinner A23)" |
| select CPU_V7 |
| select SUPPORT_SPL |
| |
| endchoice |
| |
| config DRAM_CLK |
| int "sunxi dram clock speed" |
| default 312 if MACH_SUN6I || MACH_SUN8I |
| default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| ---help--- |
| Set the dram clock speed, valid range 240 - 480, must be a multiple |
| of 24. |
| |
| config DRAM_ZQ |
| int "sunxi dram zq value" |
| default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I |
| default 127 if MACH_SUN7I |
| ---help--- |
| Set the dram zq value. |
| |
| if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I |
| config DRAM_EMR1 |
| int "sunxi dram emr1 value" |
| default 0 if MACH_SUN4I |
| default 4 if MACH_SUN5I || MACH_SUN7I |
| ---help--- |
| Set the dram controller emr1 value. |
| endif |
| |
| config SYS_CONFIG_NAME |
| default "sun4i" if MACH_SUN4I |
| default "sun5i" if MACH_SUN5I |
| default "sun6i" if MACH_SUN6I |
| default "sun7i" if MACH_SUN7I |
| default "sun8i" if MACH_SUN8I |
| |
| choice |
| prompt "Board" |
| |
| config TARGET_A10S_OLINUXINO_M |
| bool "A10S_OLINUXINO_M" |
| depends on MACH_SUN5I |
| |
| config TARGET_A13_OLINUXINOM |
| bool "A13_OLINUXINOM" |
| depends on MACH_SUN5I |
| |
| config TARGET_A13_OLINUXINO |
| bool "A13_OLINUXINO" |
| depends on MACH_SUN5I |
| |
| config TARGET_A20_OLINUXINO_L2 |
| bool "A20_OLINUXINO_L2" |
| depends on MACH_SUN7I |
| |
| config TARGET_A20_OLINUXINO_L |
| bool "A20_OLINUXINO_L" |
| depends on MACH_SUN7I |
| |
| config TARGET_A20_OLINUXINO_M |
| bool "A20_OLINUXINO_M" |
| depends on MACH_SUN7I |
| |
| config TARGET_AUXTEK_T004 |
| bool "AUXTEK_T004" |
| depends on MACH_SUN5I |
| |
| config TARGET_BANANAPI |
| bool "BANANAPI" |
| depends on MACH_SUN7I |
| |
| config TARGET_BANANAPRO |
| bool "BANANAPRO" |
| depends on MACH_SUN7I |
| |
| config TARGET_CUBIEBOARD2 |
| bool "CUBIEBOARD2" |
| depends on MACH_SUN7I |
| |
| config TARGET_CUBIETRUCK |
| bool "CUBIETRUCK" |
| depends on MACH_SUN7I |
| |
| config TARGET_PCDUINO3 |
| bool "PCDUINO3" |
| depends on MACH_SUN7I |
| |
| config TARGET_MELE_M3 |
| bool "MELE_M3" |
| depends on MACH_SUN7I |
| |
| config TARGET_MK802_A10S |
| bool "MK802_A10S" |
| depends on MACH_SUN5I |
| |
| config TARGET_MSI_PRIMO73 |
| bool "MSI Primo73 (7\" tablet)" |
| depends on MACH_SUN7I |
| ---help--- |
| The MSI Primo73 is an A20 based tablet, with 1G RAM, 16G NAND, |
| 1024x600 TN LCD display, mono speaker, 0.3 MP front camera, 2.0 MP |
| rear camera, 3000 mAh battery, gt911 touchscreen, mma8452 accelerometer |
| and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons |
| (both volume buttons are also connected to the UBOOT_SEL pin). The |
| external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB |
| OTG and 3.5mm headphone jack. More details are available at |
| http://linux-sunxi.org/MSI_Primo73 |
| |
| config TARGET_I12_TVBOX |
| bool "I12_TVBOX" |
| depends on MACH_SUN7I |
| |
| config TARGET_R7DONGLE |
| bool "R7DONGLE" |
| depends on MACH_SUN5I |
| |
| endchoice |
| |
| config SYS_BOARD |
| default "sunxi" |
| |
| config SYS_SOC |
| default "sunxi" |
| |
| config SPL_FEL |
| bool "SPL/FEL mode support" |
| depends on SPL |
| default n |
| |
| config UART0_PORT_F |
| bool "UART0 on MicroSD breakout board" |
| depends on SPL_FEL |
| default n |
| ---help--- |
| Repurpose the SD card slot for getting access to the UART0 serial |
| console. Primarily useful only for low level u-boot debugging on |
| tablets, where normal UART0 is difficult to access and requires |
| device disassembly and/or soldering. As the SD card can't be used |
| at the same time, the system can be only booted in the FEL mode. |
| Only enable this if you really know what you are doing. |
| |
| config FDTFILE |
| string "Default fdtfile env setting for this board" |
| |
| config OLD_SUNXI_KERNEL_COMPAT |
| boolean "Enable workarounds for booting old kernels" |
| default n |
| ---help--- |
| Set this to enable various workarounds for old kernels, this results in |
| sub-optimal settings for newer kernels, only enable if needed. |
| |
| config MMC0_CD_PIN |
| string "Card detect pin for mmc0" |
| default "" |
| ---help--- |
| Set the card detect pin for mmc0, leave empty to not use cd. This |
| takes a string in the format understood by sunxi_name_to_gpio, e.g. |
| PH1 for pin 1 of port H. |
| |
| config MMC1_CD_PIN |
| string "Card detect pin for mmc1" |
| default "" |
| ---help--- |
| See MMC0_CD_PIN help text. |
| |
| config MMC2_CD_PIN |
| string "Card detect pin for mmc2" |
| default "" |
| ---help--- |
| See MMC0_CD_PIN help text. |
| |
| config MMC3_CD_PIN |
| string "Card detect pin for mmc3" |
| default "" |
| ---help--- |
| See MMC0_CD_PIN help text. |
| |
| config MMC_SUNXI_SLOT_EXTRA |
| int "mmc extra slot number" |
| default -1 |
| ---help--- |
| sunxi builds always enable mmc0, some boards also have a second sdcard |
| slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable |
| support for this. |
| |
| config USB0_VBUS_PIN |
| string "Vbus enable pin for usb0 (otg)" |
| default "" |
| ---help--- |
| Set the Vbus enable pin for usb0 (otg). This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config USB1_VBUS_PIN |
| string "Vbus enable pin for usb1 (ehci0)" |
| default "PH6" if MACH_SUN4I || MACH_SUN7I |
| default "PH27" if MACH_SUN6I |
| ---help--- |
| Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes |
| a string in the format understood by sunxi_name_to_gpio, e.g. |
| PH1 for pin 1 of port H. |
| |
| config USB2_VBUS_PIN |
| string "Vbus enable pin for usb2 (ehci1)" |
| default "PH3" if MACH_SUN4I || MACH_SUN7I |
| default "PH24" if MACH_SUN6I |
| ---help--- |
| See USB1_VBUS_PIN help text. |
| |
| config VIDEO |
| boolean "Enable graphical uboot console on HDMI, LCD or VGA" |
| default y |
| ---help--- |
| Say Y here to add support for using a cfb console on the HDMI, LCD |
| or VGA output found on most sunxi devices. See doc/README.video for |
| info on how to select the video output and mode. |
| |
| config VIDEO_HDMI |
| boolean "HDMI output support" |
| depends on VIDEO && !MACH_SUN8I |
| default y |
| ---help--- |
| Say Y here to add support for outputting video over HDMI. |
| |
| config VIDEO_VGA |
| boolean "VGA output support" |
| depends on VIDEO && (MACH_SUN4I || MACH_SUN7I) |
| default n |
| ---help--- |
| Say Y here to add support for outputting video over VGA. |
| |
| config VIDEO_VGA_VIA_LCD |
| boolean "VGA via LCD controller support" |
| depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I) |
| default n |
| ---help--- |
| Say Y here to add support for external DACs connected to the parallel |
| LCD interface driving a VGA connector, such as found on the |
| Olimex A13 boards. |
| |
| config VIDEO_VGA_EXTERNAL_DAC_EN |
| string "LCD panel power enable pin" |
| depends on VIDEO_VGA_VIA_LCD |
| default "" |
| ---help--- |
| Set the enable pin for the external VGA DAC. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_MODE |
| string "LCD panel timing details" |
| depends on VIDEO |
| default "" |
| ---help--- |
| LCD panel timing details string, leave empty if there is no LCD panel. |
| This is in drivers/video/videomodes.c: video_get_params() format, e.g. |
| x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0 |
| |
| config VIDEO_LCD_DCLK_PHASE |
| int "LCD panel display clock phase" |
| depends on VIDEO |
| default 1 |
| ---help--- |
| Select LCD panel display clock phase shift, range 0-3. |
| |
| config VIDEO_LCD_POWER |
| string "LCD panel power enable pin" |
| depends on VIDEO |
| default "" |
| ---help--- |
| Set the power enable pin for the LCD panel. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_BL_EN |
| string "LCD panel backlight enable pin" |
| depends on VIDEO |
| default "" |
| ---help--- |
| Set the backlight enable pin for the LCD panel. This takes a string in the |
| the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of |
| port H. |
| |
| config VIDEO_LCD_BL_PWM |
| string "LCD panel backlight pwm pin" |
| depends on VIDEO |
| default "" |
| ---help--- |
| Set the backlight pwm pin for the LCD panel. This takes a string in the |
| format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. |
| |
| config VIDEO_LCD_BL_PWM_ACTIVE_LOW |
| bool "LCD panel backlight pwm is inverted" |
| depends on VIDEO |
| default y |
| ---help--- |
| Set this if the backlight pwm output is active low. |
| |
| |
| # Note only one of these may be selected at a time! But hidden choices are |
| # not supported by Kconfig |
| config VIDEO_LCD_IF_PARALLEL |
| bool |
| |
| config VIDEO_LCD_IF_LVDS |
| bool |
| |
| |
| choice |
| prompt "LCD panel support" |
| depends on VIDEO |
| ---help--- |
| Select which type of LCD panel to support. |
| |
| config VIDEO_LCD_PANEL_PARALLEL |
| bool "Generic parallel interface LCD panel" |
| select VIDEO_LCD_IF_PARALLEL |
| |
| config VIDEO_LCD_PANEL_LVDS |
| bool "Generic lvds interface LCD panel" |
| select VIDEO_LCD_IF_LVDS |
| |
| config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828 |
| bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip" |
| select VIDEO_LCD_SSD2828 |
| select VIDEO_LCD_IF_PARALLEL |
| ---help--- |
| 7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0 |
| |
| config VIDEO_LCD_PANEL_HITACHI_TX18D42VM |
| bool "Hitachi tx18d42vm LCD panel" |
| select VIDEO_LCD_HITACHI_TX18D42VM |
| select VIDEO_LCD_IF_LVDS |
| ---help--- |
| 7.85" 1024x768 Hitachi tx18d42vm LCD panel support |
| |
| endchoice |
| |
| |
| config USB_MUSB_SUNXI |
| bool "Enable sunxi OTG / DRC USB controller in host mode" |
| default n |
| ---help--- |
| Say y here to enable support for the sunxi OTG / DRC USB controller |
| used on almost all sunxi boards. Note currently u-boot can only have |
| one usb host controller enabled at a time, so enabling this on boards |
| which also use the ehci host controller will result in build errors. |
| |
| config USB_KEYBOARD |
| boolean "Enable USB keyboard support" |
| default y |
| ---help--- |
| Say Y here to add support for using a USB keyboard (typically used |
| in combination with a graphical console). |
| |
| config GMAC_TX_DELAY |
| int "GMAC Transmit Clock Delay Chain" |
| default 0 |
| ---help--- |
| Set the GMAC Transmit Clock Delay Chain value. |
| |
| endif |