| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * MediaTek SD/MMC Card Interface driver |
| * |
| * Copyright (C) 2018 MediaTek Inc. |
| * Author: Weijie Gao <weijie.gao@mediatek.com> |
| */ |
| |
| #include <clk.h> |
| #include <common.h> |
| #include <dm.h> |
| #include <mmc.h> |
| #include <errno.h> |
| #include <malloc.h> |
| #include <mapmem.h> |
| #include <stdbool.h> |
| #include <asm/gpio.h> |
| #include <dm/device_compat.h> |
| #include <dm/pinctrl.h> |
| #include <linux/bitops.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| |
| /* MSDC_CFG */ |
| #define MSDC_CFG_HS400_CK_MODE_EXT BIT(22) |
| #define MSDC_CFG_CKMOD_EXT_M 0x300000 |
| #define MSDC_CFG_CKMOD_EXT_S 20 |
| #define MSDC_CFG_CKDIV_EXT_M 0xfff00 |
| #define MSDC_CFG_CKDIV_EXT_S 8 |
| #define MSDC_CFG_HS400_CK_MODE BIT(18) |
| #define MSDC_CFG_CKMOD_M 0x30000 |
| #define MSDC_CFG_CKMOD_S 16 |
| #define MSDC_CFG_CKDIV_M 0xff00 |
| #define MSDC_CFG_CKDIV_S 8 |
| #define MSDC_CFG_CKSTB BIT(7) |
| #define MSDC_CFG_PIO BIT(3) |
| #define MSDC_CFG_RST BIT(2) |
| #define MSDC_CFG_CKPDN BIT(1) |
| #define MSDC_CFG_MODE BIT(0) |
| |
| /* MSDC_IOCON */ |
| #define MSDC_IOCON_W_DSPL BIT(8) |
| #define MSDC_IOCON_DSPL BIT(2) |
| #define MSDC_IOCON_RSPL BIT(1) |
| |
| /* MSDC_PS */ |
| #define MSDC_PS_DAT0 BIT(16) |
| #define MSDC_PS_CDDBCE_M 0xf000 |
| #define MSDC_PS_CDDBCE_S 12 |
| #define MSDC_PS_CDSTS BIT(1) |
| #define MSDC_PS_CDEN BIT(0) |
| |
| /* #define MSDC_INT(EN) */ |
| #define MSDC_INT_ACMDRDY BIT(3) |
| #define MSDC_INT_ACMDTMO BIT(4) |
| #define MSDC_INT_ACMDCRCERR BIT(5) |
| #define MSDC_INT_CMDRDY BIT(8) |
| #define MSDC_INT_CMDTMO BIT(9) |
| #define MSDC_INT_RSPCRCERR BIT(10) |
| #define MSDC_INT_XFER_COMPL BIT(12) |
| #define MSDC_INT_DATTMO BIT(14) |
| #define MSDC_INT_DATCRCERR BIT(15) |
| |
| /* MSDC_FIFOCS */ |
| #define MSDC_FIFOCS_CLR BIT(31) |
| #define MSDC_FIFOCS_TXCNT_M 0xff0000 |
| #define MSDC_FIFOCS_TXCNT_S 16 |
| #define MSDC_FIFOCS_RXCNT_M 0xff |
| #define MSDC_FIFOCS_RXCNT_S 0 |
| |
| /* #define SDC_CFG */ |
| #define SDC_CFG_DTOC_M 0xff000000 |
| #define SDC_CFG_DTOC_S 24 |
| #define SDC_CFG_SDIOIDE BIT(20) |
| #define SDC_CFG_SDIO BIT(19) |
| #define SDC_CFG_BUSWIDTH_M 0x30000 |
| #define SDC_CFG_BUSWIDTH_S 16 |
| |
| /* SDC_CMD */ |
| #define SDC_CMD_BLK_LEN_M 0xfff0000 |
| #define SDC_CMD_BLK_LEN_S 16 |
| #define SDC_CMD_STOP BIT(14) |
| #define SDC_CMD_WR BIT(13) |
| #define SDC_CMD_DTYPE_M 0x1800 |
| #define SDC_CMD_DTYPE_S 11 |
| #define SDC_CMD_RSPTYP_M 0x380 |
| #define SDC_CMD_RSPTYP_S 7 |
| #define SDC_CMD_CMD_M 0x3f |
| #define SDC_CMD_CMD_S 0 |
| |
| /* SDC_STS */ |
| #define SDC_STS_CMDBUSY BIT(1) |
| #define SDC_STS_SDCBUSY BIT(0) |
| |
| /* SDC_ADV_CFG0 */ |
| #define SDC_RX_ENHANCE_EN BIT(20) |
| |
| /* PATCH_BIT0 */ |
| #define MSDC_INT_DAT_LATCH_CK_SEL_M 0x380 |
| #define MSDC_INT_DAT_LATCH_CK_SEL_S 7 |
| |
| /* PATCH_BIT1 */ |
| #define MSDC_PB1_STOP_DLY_M 0xf00 |
| #define MSDC_PB1_STOP_DLY_S 8 |
| |
| /* PATCH_BIT2 */ |
| #define MSDC_PB2_CRCSTSENSEL_M 0xe0000000 |
| #define MSDC_PB2_CRCSTSENSEL_S 29 |
| #define MSDC_PB2_CFGCRCSTS BIT(28) |
| #define MSDC_PB2_RESPSTSENSEL_M 0x70000 |
| #define MSDC_PB2_RESPSTSENSEL_S 16 |
| #define MSDC_PB2_CFGRESP BIT(15) |
| #define MSDC_PB2_RESPWAIT_M 0x0c |
| #define MSDC_PB2_RESPWAIT_S 2 |
| |
| /* MSDC_PAD_CTRL0 */ |
| #define MSDC_PAD_CTRL0_CLKRDSEL_M 0xff000000 |
| #define MSDC_PAD_CTRL0_CLKRDSEL_S 24 |
| #define MSDC_PAD_CTRL0_CLKTDSEL BIT(20) |
| #define MSDC_PAD_CTRL0_CLKIES BIT(19) |
| #define MSDC_PAD_CTRL0_CLKSMT BIT(18) |
| #define MSDC_PAD_CTRL0_CLKPU BIT(17) |
| #define MSDC_PAD_CTRL0_CLKPD BIT(16) |
| #define MSDC_PAD_CTRL0_CLKSR BIT(8) |
| #define MSDC_PAD_CTRL0_CLKDRVP_M 0x70 |
| #define MSDC_PAD_CTRL0_CLKDRVP_S 4 |
| #define MSDC_PAD_CTRL0_CLKDRVN_M 0x7 |
| #define MSDC_PAD_CTRL0_CLKDRVN_S 0 |
| |
| /* MSDC_PAD_CTRL1 */ |
| #define MSDC_PAD_CTRL1_CMDRDSEL_M 0xff000000 |
| #define MSDC_PAD_CTRL1_CMDRDSEL_S 24 |
| #define MSDC_PAD_CTRL1_CMDTDSEL BIT(20) |
| #define MSDC_PAD_CTRL1_CMDIES BIT(19) |
| #define MSDC_PAD_CTRL1_CMDSMT BIT(18) |
| #define MSDC_PAD_CTRL1_CMDPU BIT(17) |
| #define MSDC_PAD_CTRL1_CMDPD BIT(16) |
| #define MSDC_PAD_CTRL1_CMDSR BIT(8) |
| #define MSDC_PAD_CTRL1_CMDDRVP_M 0x70 |
| #define MSDC_PAD_CTRL1_CMDDRVP_S 4 |
| #define MSDC_PAD_CTRL1_CMDDRVN_M 0x7 |
| #define MSDC_PAD_CTRL1_CMDDRVN_S 0 |
| |
| /* MSDC_PAD_CTRL2 */ |
| #define MSDC_PAD_CTRL2_DATRDSEL_M 0xff000000 |
| #define MSDC_PAD_CTRL2_DATRDSEL_S 24 |
| #define MSDC_PAD_CTRL2_DATTDSEL BIT(20) |
| #define MSDC_PAD_CTRL2_DATIES BIT(19) |
| #define MSDC_PAD_CTRL2_DATSMT BIT(18) |
| #define MSDC_PAD_CTRL2_DATPU BIT(17) |
| #define MSDC_PAD_CTRL2_DATPD BIT(16) |
| #define MSDC_PAD_CTRL2_DATSR BIT(8) |
| #define MSDC_PAD_CTRL2_DATDRVP_M 0x70 |
| #define MSDC_PAD_CTRL2_DATDRVP_S 4 |
| #define MSDC_PAD_CTRL2_DATDRVN_M 0x7 |
| #define MSDC_PAD_CTRL2_DATDRVN_S 0 |
| |
| /* PAD_TUNE */ |
| #define MSDC_PAD_TUNE_CLKTDLY_M 0xf8000000 |
| #define MSDC_PAD_TUNE_CLKTDLY_S 27 |
| #define MSDC_PAD_TUNE_CMDRRDLY_M 0x7c00000 |
| #define MSDC_PAD_TUNE_CMDRRDLY_S 22 |
| #define MSDC_PAD_TUNE_CMD_SEL BIT(21) |
| #define MSDC_PAD_TUNE_CMDRDLY_M 0x1f0000 |
| #define MSDC_PAD_TUNE_CMDRDLY_S 16 |
| #define MSDC_PAD_TUNE_RXDLYSEL BIT(15) |
| #define MSDC_PAD_TUNE_RD_SEL BIT(13) |
| #define MSDC_PAD_TUNE_DATRRDLY_M 0x1f00 |
| #define MSDC_PAD_TUNE_DATRRDLY_S 8 |
| #define MSDC_PAD_TUNE_DATWRDLY_M 0x1f |
| #define MSDC_PAD_TUNE_DATWRDLY_S 0 |
| |
| #define PAD_CMD_TUNE_RX_DLY3 0x3E |
| #define PAD_CMD_TUNE_RX_DLY3_S 1 |
| |
| /* PAD_TUNE0 */ |
| #define MSDC_PAD_TUNE0_DAT0RDDLY_M 0x1f000000 |
| #define MSDC_PAD_TUNE0_DAT0RDDLY_S 24 |
| #define MSDC_PAD_TUNE0_DAT1RDDLY_M 0x1f0000 |
| #define MSDC_PAD_TUNE0_DAT1RDDLY_S 16 |
| #define MSDC_PAD_TUNE0_DAT2RDDLY_M 0x1f00 |
| #define MSDC_PAD_TUNE0_DAT2RDDLY_S 8 |
| #define MSDC_PAD_TUNE0_DAT3RDDLY_M 0x1f |
| #define MSDC_PAD_TUNE0_DAT3RDDLY_S 0 |
| |
| /* PAD_TUNE1 */ |
| #define MSDC_PAD_TUNE1_DAT4RDDLY_M 0x1f000000 |
| #define MSDC_PAD_TUNE1_DAT4RDDLY_S 24 |
| #define MSDC_PAD_TUNE1_DAT5RDDLY_M 0x1f0000 |
| #define MSDC_PAD_TUNE1_DAT5RDDLY_S 16 |
| #define MSDC_PAD_TUNE1_DAT6RDDLY_M 0x1f00 |
| #define MSDC_PAD_TUNE1_DAT6RDDLY_S 8 |
| #define MSDC_PAD_TUNE1_DAT7RDDLY_M 0x1f |
| #define MSDC_PAD_TUNE1_DAT7RDDLY_S 0 |
| |
| /* EMMC50_CFG0 */ |
| #define EMMC50_CFG_CFCSTS_SEL BIT(4) |
| |
| /* SDC_FIFO_CFG */ |
| #define SDC_FIFO_CFG_WRVALIDSEL BIT(24) |
| #define SDC_FIFO_CFG_RDVALIDSEL BIT(25) |
| |
| /* EMMC_TOP_CONTROL mask */ |
| #define PAD_RXDLY_SEL BIT(0) |
| #define DELAY_EN BIT(1) |
| #define PAD_DAT_RD_RXDLY2 (0x1f << 2) |
| #define PAD_DAT_RD_RXDLY (0x1f << 7) |
| #define PAD_DAT_RD_RXDLY_S 7 |
| #define PAD_DAT_RD_RXDLY2_SEL BIT(12) |
| #define PAD_DAT_RD_RXDLY_SEL BIT(13) |
| #define DATA_K_VALUE_SEL BIT(14) |
| #define SDC_RX_ENH_EN BIT(15) |
| |
| /* EMMC_TOP_CMD mask */ |
| #define PAD_CMD_RXDLY2 (0x1f << 0) |
| #define PAD_CMD_RXDLY (0x1f << 5) |
| #define PAD_CMD_RXDLY_S 5 |
| #define PAD_CMD_RD_RXDLY2_SEL BIT(10) |
| #define PAD_CMD_RD_RXDLY_SEL BIT(11) |
| #define PAD_CMD_TX_DLY (0x1f << 12) |
| |
| /* SDC_CFG_BUSWIDTH */ |
| #define MSDC_BUS_1BITS 0x0 |
| #define MSDC_BUS_4BITS 0x1 |
| #define MSDC_BUS_8BITS 0x2 |
| |
| #define MSDC_FIFO_SIZE 128 |
| |
| #define PAD_DELAY_MAX 32 |
| |
| #define DEFAULT_CD_DEBOUNCE 8 |
| |
| #define SCLK_CYCLES_SHIFT 20 |
| |
| #define MIN_BUS_CLK 200000 |
| |
| #define CMD_INTS_MASK \ |
| (MSDC_INT_CMDRDY | MSDC_INT_RSPCRCERR | MSDC_INT_CMDTMO) |
| |
| #define DATA_INTS_MASK \ |
| (MSDC_INT_XFER_COMPL | MSDC_INT_DATTMO | MSDC_INT_DATCRCERR) |
| |
| /* Register offset */ |
| struct mtk_sd_regs { |
| u32 msdc_cfg; |
| u32 msdc_iocon; |
| u32 msdc_ps; |
| u32 msdc_int; |
| u32 msdc_inten; |
| u32 msdc_fifocs; |
| u32 msdc_txdata; |
| u32 msdc_rxdata; |
| u32 reserved0[4]; |
| u32 sdc_cfg; |
| u32 sdc_cmd; |
| u32 sdc_arg; |
| u32 sdc_sts; |
| u32 sdc_resp[4]; |
| u32 sdc_blk_num; |
| u32 sdc_vol_chg; |
| u32 sdc_csts; |
| u32 sdc_csts_en; |
| u32 sdc_datcrc_sts; |
| u32 sdc_adv_cfg0; |
| u32 reserved1[2]; |
| u32 emmc_cfg0; |
| u32 emmc_cfg1; |
| u32 emmc_sts; |
| u32 emmc_iocon; |
| u32 sd_acmd_resp; |
| u32 sd_acmd19_trg; |
| u32 sd_acmd19_sts; |
| u32 dma_sa_high4bit; |
| u32 dma_sa; |
| u32 dma_ca; |
| u32 dma_ctrl; |
| u32 dma_cfg; |
| u32 sw_dbg_sel; |
| u32 sw_dbg_out; |
| u32 dma_length; |
| u32 reserved2; |
| u32 patch_bit0; |
| u32 patch_bit1; |
| u32 patch_bit2; |
| u32 reserved3; |
| u32 dat0_tune_crc; |
| u32 dat1_tune_crc; |
| u32 dat2_tune_crc; |
| u32 dat3_tune_crc; |
| u32 cmd_tune_crc; |
| u32 sdio_tune_wind; |
| u32 reserved4[2]; |
| u32 pad_ctrl0; |
| u32 pad_ctrl1; |
| u32 pad_ctrl2; |
| u32 pad_tune; |
| u32 pad_tune0; |
| u32 pad_tune1; |
| u32 dat_rd_dly[4]; |
| u32 reserved5[2]; |
| u32 hw_dbg_sel; |
| u32 main_ver; |
| u32 eco_ver; |
| u32 reserved6[27]; |
| u32 pad_ds_tune; |
| u32 pad_cmd_tune; |
| u32 reserved7[30]; |
| u32 emmc50_cfg0; |
| u32 reserved8[7]; |
| u32 sdc_fifo_cfg; |
| }; |
| |
| struct msdc_top_regs { |
| u32 emmc_top_control; |
| u32 emmc_top_cmd; |
| u32 emmc50_pad_ctl0; |
| u32 emmc50_pad_ds_tune; |
| u32 emmc50_pad_dat0_tune; |
| u32 emmc50_pad_dat1_tune; |
| u32 emmc50_pad_dat2_tune; |
| u32 emmc50_pad_dat3_tune; |
| u32 emmc50_pad_dat4_tune; |
| u32 emmc50_pad_dat5_tune; |
| u32 emmc50_pad_dat6_tune; |
| u32 emmc50_pad_dat7_tune; |
| }; |
| |
| struct msdc_compatible { |
| u8 clk_div_bits; |
| bool pad_tune0; |
| bool async_fifo; |
| bool data_tune; |
| bool busy_check; |
| bool stop_clk_fix; |
| bool enhance_rx; |
| bool builtin_pad_ctrl; |
| bool default_pad_dly; |
| }; |
| |
| struct msdc_delay_phase { |
| u8 maxlen; |
| u8 start; |
| u8 final_phase; |
| }; |
| |
| struct msdc_plat { |
| struct mmc_config cfg; |
| struct mmc mmc; |
| }; |
| |
| struct msdc_tune_para { |
| u32 iocon; |
| u32 pad_tune; |
| u32 pad_cmd_tune; |
| }; |
| |
| struct msdc_host { |
| struct mtk_sd_regs *base; |
| struct msdc_top_regs *top_base; |
| struct mmc *mmc; |
| |
| struct msdc_compatible *dev_comp; |
| |
| struct clk src_clk; /* for SD/MMC bus clock */ |
| struct clk src_clk_cg; /* optional, MSDC source clock control gate */ |
| struct clk h_clk; /* MSDC core clock */ |
| |
| u32 src_clk_freq; /* source clock */ |
| u32 mclk; /* mmc framework required bus clock */ |
| u32 sclk; /* actual calculated bus clock */ |
| |
| /* operation timeout clocks */ |
| u32 timeout_ns; |
| u32 timeout_clks; |
| |
| /* tuning options */ |
| u32 hs400_ds_delay; |
| u32 hs200_cmd_int_delay; |
| u32 hs200_write_int_delay; |
| u32 latch_ck; |
| u32 r_smpl; /* sample edge */ |
| bool hs400_mode; |
| |
| /* whether to use gpio detection or built-in hw detection */ |
| bool builtin_cd; |
| bool cd_active_high; |
| |
| /* card detection / write protection GPIOs */ |
| #if CONFIG_IS_ENABLED(DM_GPIO) |
| struct gpio_desc gpio_wp; |
| struct gpio_desc gpio_cd; |
| #endif |
| |
| uint last_resp_type; |
| uint last_data_write; |
| |
| enum bus_mode timing; |
| |
| struct msdc_tune_para def_tune_para; |
| struct msdc_tune_para saved_tune_para; |
| }; |
| |
| static void msdc_reset_hw(struct msdc_host *host) |
| { |
| u32 reg; |
| |
| setbits_le32(&host->base->msdc_cfg, MSDC_CFG_RST); |
| |
| readl_poll_timeout(&host->base->msdc_cfg, reg, |
| !(reg & MSDC_CFG_RST), 1000000); |
| } |
| |
| static void msdc_fifo_clr(struct msdc_host *host) |
| { |
| u32 reg; |
| |
| setbits_le32(&host->base->msdc_fifocs, MSDC_FIFOCS_CLR); |
| |
| readl_poll_timeout(&host->base->msdc_fifocs, reg, |
| !(reg & MSDC_FIFOCS_CLR), 1000000); |
| } |
| |
| static u32 msdc_fifo_rx_bytes(struct msdc_host *host) |
| { |
| return (readl(&host->base->msdc_fifocs) & |
| MSDC_FIFOCS_RXCNT_M) >> MSDC_FIFOCS_RXCNT_S; |
| } |
| |
| static u32 msdc_fifo_tx_bytes(struct msdc_host *host) |
| { |
| return (readl(&host->base->msdc_fifocs) & |
| MSDC_FIFOCS_TXCNT_M) >> MSDC_FIFOCS_TXCNT_S; |
| } |
| |
| static u32 msdc_cmd_find_resp(struct msdc_host *host, struct mmc_cmd *cmd) |
| { |
| u32 resp; |
| |
| switch (cmd->resp_type) { |
| /* Actually, R1, R5, R6, R7 are the same */ |
| case MMC_RSP_R1: |
| resp = 0x1; |
| break; |
| case MMC_RSP_R1b: |
| resp = 0x7; |
| break; |
| case MMC_RSP_R2: |
| resp = 0x2; |
| break; |
| case MMC_RSP_R3: |
| resp = 0x3; |
| break; |
| case MMC_RSP_NONE: |
| default: |
| resp = 0x0; |
| break; |
| } |
| |
| return resp; |
| } |
| |
| static u32 msdc_cmd_prepare_raw_cmd(struct msdc_host *host, |
| struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| u32 opcode = cmd->cmdidx; |
| u32 resp_type = msdc_cmd_find_resp(host, cmd); |
| uint blocksize = 0; |
| u32 dtype = 0; |
| u32 rawcmd = 0; |
| |
| switch (opcode) { |
| case MMC_CMD_WRITE_MULTIPLE_BLOCK: |
| case MMC_CMD_READ_MULTIPLE_BLOCK: |
| dtype = 2; |
| break; |
| case MMC_CMD_WRITE_SINGLE_BLOCK: |
| case MMC_CMD_READ_SINGLE_BLOCK: |
| case SD_CMD_APP_SEND_SCR: |
| case MMC_CMD_SEND_TUNING_BLOCK: |
| case MMC_CMD_SEND_TUNING_BLOCK_HS200: |
| dtype = 1; |
| break; |
| case SD_CMD_SWITCH_FUNC: /* same as MMC_CMD_SWITCH */ |
| case SD_CMD_SEND_IF_COND: /* same as MMC_CMD_SEND_EXT_CSD */ |
| case SD_CMD_APP_SD_STATUS: /* same as MMC_CMD_SEND_STATUS */ |
| if (data) |
| dtype = 1; |
| } |
| |
| if (data) { |
| if (data->flags == MMC_DATA_WRITE) |
| rawcmd |= SDC_CMD_WR; |
| |
| if (data->blocks > 1) |
| dtype = 2; |
| |
| blocksize = data->blocksize; |
| } |
| |
| rawcmd |= ((opcode << SDC_CMD_CMD_S) & SDC_CMD_CMD_M) | |
| ((resp_type << SDC_CMD_RSPTYP_S) & SDC_CMD_RSPTYP_M) | |
| ((blocksize << SDC_CMD_BLK_LEN_S) & SDC_CMD_BLK_LEN_M) | |
| ((dtype << SDC_CMD_DTYPE_S) & SDC_CMD_DTYPE_M); |
| |
| if (opcode == MMC_CMD_STOP_TRANSMISSION) |
| rawcmd |= SDC_CMD_STOP; |
| |
| return rawcmd; |
| } |
| |
| static int msdc_cmd_done(struct msdc_host *host, int events, |
| struct mmc_cmd *cmd) |
| { |
| u32 *rsp = cmd->response; |
| int ret = 0; |
| |
| if (cmd->resp_type & MMC_RSP_PRESENT) { |
| if (cmd->resp_type & MMC_RSP_136) { |
| rsp[0] = readl(&host->base->sdc_resp[3]); |
| rsp[1] = readl(&host->base->sdc_resp[2]); |
| rsp[2] = readl(&host->base->sdc_resp[1]); |
| rsp[3] = readl(&host->base->sdc_resp[0]); |
| } else { |
| rsp[0] = readl(&host->base->sdc_resp[0]); |
| } |
| } |
| |
| if (!(events & MSDC_INT_CMDRDY)) { |
| if (cmd->cmdidx != MMC_CMD_SEND_TUNING_BLOCK && |
| cmd->cmdidx != MMC_CMD_SEND_TUNING_BLOCK_HS200) |
| /* |
| * should not clear fifo/interrupt as the tune data |
| * may have alreay come. |
| */ |
| msdc_reset_hw(host); |
| |
| if (events & MSDC_INT_CMDTMO) |
| ret = -ETIMEDOUT; |
| else |
| ret = -EIO; |
| } |
| |
| return ret; |
| } |
| |
| static bool msdc_cmd_is_ready(struct msdc_host *host) |
| { |
| int ret; |
| u32 reg; |
| |
| /* The max busy time we can endure is 20ms */ |
| ret = readl_poll_timeout(&host->base->sdc_sts, reg, |
| !(reg & SDC_STS_CMDBUSY), 20000); |
| |
| if (ret) { |
| pr_err("CMD bus busy detected\n"); |
| msdc_reset_hw(host); |
| return false; |
| } |
| |
| if (host->last_resp_type == MMC_RSP_R1b && host->last_data_write) { |
| ret = readl_poll_timeout(&host->base->msdc_ps, reg, |
| reg & MSDC_PS_DAT0, 1000000); |
| |
| if (ret) { |
| pr_err("Card stuck in programming state!\n"); |
| msdc_reset_hw(host); |
| return false; |
| } |
| } |
| |
| return true; |
| } |
| |
| static int msdc_start_command(struct msdc_host *host, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| u32 rawcmd; |
| u32 status; |
| u32 blocks = 0; |
| int ret; |
| |
| if (!msdc_cmd_is_ready(host)) |
| return -EIO; |
| |
| if ((readl(&host->base->msdc_fifocs) & |
| MSDC_FIFOCS_TXCNT_M) >> MSDC_FIFOCS_TXCNT_S || |
| (readl(&host->base->msdc_fifocs) & |
| MSDC_FIFOCS_RXCNT_M) >> MSDC_FIFOCS_RXCNT_S) { |
| pr_err("TX/RX FIFO non-empty before start of IO. Reset\n"); |
| msdc_reset_hw(host); |
| } |
| |
| msdc_fifo_clr(host); |
| |
| host->last_resp_type = cmd->resp_type; |
| host->last_data_write = 0; |
| |
| rawcmd = msdc_cmd_prepare_raw_cmd(host, cmd, data); |
| |
| if (data) |
| blocks = data->blocks; |
| |
| writel(CMD_INTS_MASK, &host->base->msdc_int); |
| writel(DATA_INTS_MASK, &host->base->msdc_int); |
| writel(blocks, &host->base->sdc_blk_num); |
| writel(cmd->cmdarg, &host->base->sdc_arg); |
| writel(rawcmd, &host->base->sdc_cmd); |
| |
| ret = readl_poll_timeout(&host->base->msdc_int, status, |
| status & CMD_INTS_MASK, 1000000); |
| |
| if (ret) |
| status = MSDC_INT_CMDTMO; |
| |
| return msdc_cmd_done(host, status, cmd); |
| } |
| |
| static void msdc_fifo_read(struct msdc_host *host, u8 *buf, u32 size) |
| { |
| u32 *wbuf; |
| |
| while ((size_t)buf % 4) { |
| *buf++ = readb(&host->base->msdc_rxdata); |
| size--; |
| } |
| |
| wbuf = (u32 *)buf; |
| while (size >= 4) { |
| *wbuf++ = readl(&host->base->msdc_rxdata); |
| size -= 4; |
| } |
| |
| buf = (u8 *)wbuf; |
| while (size) { |
| *buf++ = readb(&host->base->msdc_rxdata); |
| size--; |
| } |
| } |
| |
| static void msdc_fifo_write(struct msdc_host *host, const u8 *buf, u32 size) |
| { |
| const u32 *wbuf; |
| |
| while ((size_t)buf % 4) { |
| writeb(*buf++, &host->base->msdc_txdata); |
| size--; |
| } |
| |
| wbuf = (const u32 *)buf; |
| while (size >= 4) { |
| writel(*wbuf++, &host->base->msdc_txdata); |
| size -= 4; |
| } |
| |
| buf = (const u8 *)wbuf; |
| while (size) { |
| writeb(*buf++, &host->base->msdc_txdata); |
| size--; |
| } |
| } |
| |
| static int msdc_pio_read(struct msdc_host *host, u8 *ptr, u32 size) |
| { |
| u32 status; |
| u32 chksz; |
| int ret = 0; |
| |
| while (1) { |
| status = readl(&host->base->msdc_int); |
| writel(status, &host->base->msdc_int); |
| status &= DATA_INTS_MASK; |
| |
| if (status & MSDC_INT_DATCRCERR) { |
| ret = -EIO; |
| break; |
| } |
| |
| if (status & MSDC_INT_DATTMO) { |
| ret = -ETIMEDOUT; |
| break; |
| } |
| |
| chksz = min(size, (u32)MSDC_FIFO_SIZE); |
| |
| if (msdc_fifo_rx_bytes(host) >= chksz) { |
| msdc_fifo_read(host, ptr, chksz); |
| ptr += chksz; |
| size -= chksz; |
| } |
| |
| if (status & MSDC_INT_XFER_COMPL) { |
| if (size) { |
| pr_err("data not fully read\n"); |
| ret = -EIO; |
| } |
| |
| break; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int msdc_pio_write(struct msdc_host *host, const u8 *ptr, u32 size) |
| { |
| u32 status; |
| u32 chksz; |
| int ret = 0; |
| |
| while (1) { |
| status = readl(&host->base->msdc_int); |
| writel(status, &host->base->msdc_int); |
| status &= DATA_INTS_MASK; |
| |
| if (status & MSDC_INT_DATCRCERR) { |
| ret = -EIO; |
| break; |
| } |
| |
| if (status & MSDC_INT_DATTMO) { |
| ret = -ETIMEDOUT; |
| break; |
| } |
| |
| if (status & MSDC_INT_XFER_COMPL) { |
| if (size) { |
| pr_err("data not fully written\n"); |
| ret = -EIO; |
| } |
| |
| break; |
| } |
| |
| chksz = min(size, (u32)MSDC_FIFO_SIZE); |
| |
| if (MSDC_FIFO_SIZE - msdc_fifo_tx_bytes(host) >= chksz) { |
| msdc_fifo_write(host, ptr, chksz); |
| ptr += chksz; |
| size -= chksz; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int msdc_start_data(struct msdc_host *host, struct mmc_data *data) |
| { |
| u32 size; |
| int ret; |
| |
| if (data->flags == MMC_DATA_WRITE) |
| host->last_data_write = 1; |
| |
| size = data->blocks * data->blocksize; |
| |
| if (data->flags == MMC_DATA_WRITE) |
| ret = msdc_pio_write(host, (const u8 *)data->src, size); |
| else |
| ret = msdc_pio_read(host, (u8 *)data->dest, size); |
| |
| if (ret) { |
| msdc_reset_hw(host); |
| msdc_fifo_clr(host); |
| } |
| |
| return ret; |
| } |
| |
| static int msdc_ops_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| struct msdc_host *host = dev_get_priv(dev); |
| int cmd_ret, data_ret; |
| |
| cmd_ret = msdc_start_command(host, cmd, data); |
| if (cmd_ret && |
| !(cmd_ret == -EIO && |
| (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK || |
| cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200))) |
| return cmd_ret; |
| |
| if (data) { |
| data_ret = msdc_start_data(host, data); |
| if (cmd_ret) |
| return cmd_ret; |
| else |
| return data_ret; |
| } |
| |
| return 0; |
| } |
| |
| static void msdc_set_timeout(struct msdc_host *host, u32 ns, u32 clks) |
| { |
| u32 timeout, clk_ns, shift = SCLK_CYCLES_SHIFT; |
| u32 mode = 0; |
| |
| host->timeout_ns = ns; |
| host->timeout_clks = clks; |
| |
| if (host->sclk == 0) { |
| timeout = 0; |
| } else { |
| clk_ns = 1000000000UL / host->sclk; |
| timeout = (ns + clk_ns - 1) / clk_ns + clks; |
| /* unit is 1048576 sclk cycles */ |
| timeout = (timeout + (0x1 << shift) - 1) >> shift; |
| if (host->dev_comp->clk_div_bits == 8) |
| mode = (readl(&host->base->msdc_cfg) & |
| MSDC_CFG_CKMOD_M) >> MSDC_CFG_CKMOD_S; |
| else |
| mode = (readl(&host->base->msdc_cfg) & |
| MSDC_CFG_CKMOD_EXT_M) >> MSDC_CFG_CKMOD_EXT_S; |
| /* DDR mode will double the clk cycles for data timeout */ |
| timeout = mode >= 2 ? timeout * 2 : timeout; |
| timeout = timeout > 1 ? timeout - 1 : 0; |
| timeout = timeout > 255 ? 255 : timeout; |
| } |
| |
| clrsetbits_le32(&host->base->sdc_cfg, SDC_CFG_DTOC_M, |
| timeout << SDC_CFG_DTOC_S); |
| } |
| |
| static void msdc_set_buswidth(struct msdc_host *host, u32 width) |
| { |
| u32 val = readl(&host->base->sdc_cfg); |
| |
| val &= ~SDC_CFG_BUSWIDTH_M; |
| |
| switch (width) { |
| default: |
| case 1: |
| val |= (MSDC_BUS_1BITS << SDC_CFG_BUSWIDTH_S); |
| break; |
| case 4: |
| val |= (MSDC_BUS_4BITS << SDC_CFG_BUSWIDTH_S); |
| break; |
| case 8: |
| val |= (MSDC_BUS_8BITS << SDC_CFG_BUSWIDTH_S); |
| break; |
| } |
| |
| writel(val, &host->base->sdc_cfg); |
| } |
| |
| static void msdc_set_mclk(struct udevice *dev, |
| struct msdc_host *host, enum bus_mode timing, u32 hz) |
| { |
| u32 mode; |
| u32 div; |
| u32 sclk; |
| u32 reg; |
| |
| if (!hz) { |
| host->mclk = 0; |
| clrbits_le32(&host->base->msdc_cfg, MSDC_CFG_CKPDN); |
| return; |
| } |
| |
| if (host->dev_comp->clk_div_bits == 8) |
| clrbits_le32(&host->base->msdc_cfg, MSDC_CFG_HS400_CK_MODE); |
| else |
| clrbits_le32(&host->base->msdc_cfg, |
| MSDC_CFG_HS400_CK_MODE_EXT); |
| |
| if (timing == UHS_DDR50 || timing == MMC_DDR_52 || |
| timing == MMC_HS_400) { |
| if (timing == MMC_HS_400) |
| mode = 0x3; |
| else |
| mode = 0x2; /* ddr mode and use divisor */ |
| |
| if (hz >= (host->src_clk_freq >> 2)) { |
| div = 0; /* mean div = 1/4 */ |
| sclk = host->src_clk_freq >> 2; /* sclk = clk / 4 */ |
| } else { |
| div = (host->src_clk_freq + ((hz << 2) - 1)) / |
| (hz << 2); |
| sclk = (host->src_clk_freq >> 2) / div; |
| div = (div >> 1); |
| } |
| |
| if (timing == MMC_HS_400 && hz >= (host->src_clk_freq >> 1)) { |
| if (host->dev_comp->clk_div_bits == 8) |
| setbits_le32(&host->base->msdc_cfg, |
| MSDC_CFG_HS400_CK_MODE); |
| else |
| setbits_le32(&host->base->msdc_cfg, |
| MSDC_CFG_HS400_CK_MODE_EXT); |
| |
| sclk = host->src_clk_freq >> 1; |
| div = 0; /* div is ignore when bit18 is set */ |
| } |
| } else if (hz >= host->src_clk_freq) { |
| mode = 0x1; /* no divisor */ |
| div = 0; |
| sclk = host->src_clk_freq; |
| } else { |
| mode = 0x0; /* use divisor */ |
| if (hz >= (host->src_clk_freq >> 1)) { |
| div = 0; /* mean div = 1/2 */ |
| sclk = host->src_clk_freq >> 1; /* sclk = clk / 2 */ |
| } else { |
| div = (host->src_clk_freq + ((hz << 2) - 1)) / |
| (hz << 2); |
| sclk = (host->src_clk_freq >> 2) / div; |
| } |
| } |
| |
| clrbits_le32(&host->base->msdc_cfg, MSDC_CFG_CKPDN); |
| |
| if (host->dev_comp->clk_div_bits == 8) { |
| div = min(div, (u32)(MSDC_CFG_CKDIV_M >> MSDC_CFG_CKDIV_S)); |
| clrsetbits_le32(&host->base->msdc_cfg, |
| MSDC_CFG_CKMOD_M | MSDC_CFG_CKDIV_M, |
| (mode << MSDC_CFG_CKMOD_S) | |
| (div << MSDC_CFG_CKDIV_S)); |
| } else { |
| div = min(div, (u32)(MSDC_CFG_CKDIV_EXT_M >> |
| MSDC_CFG_CKDIV_EXT_S)); |
| clrsetbits_le32(&host->base->msdc_cfg, |
| MSDC_CFG_CKMOD_EXT_M | MSDC_CFG_CKDIV_EXT_M, |
| (mode << MSDC_CFG_CKMOD_EXT_S) | |
| (div << MSDC_CFG_CKDIV_EXT_S)); |
| } |
| |
| readl_poll_timeout(&host->base->msdc_cfg, reg, |
| reg & MSDC_CFG_CKSTB, 1000000); |
| |
| setbits_le32(&host->base->msdc_cfg, MSDC_CFG_CKPDN); |
| host->sclk = sclk; |
| host->mclk = hz; |
| host->timing = timing; |
| |
| /* needed because clk changed. */ |
| msdc_set_timeout(host, host->timeout_ns, host->timeout_clks); |
| |
| /* |
| * mmc_select_hs400() will drop to 50Mhz and High speed mode, |
| * tune result of hs200/200Mhz is not suitable for 50Mhz |
| */ |
| if (host->sclk <= 52000000) { |
| writel(host->def_tune_para.iocon, &host->base->msdc_iocon); |
| writel(host->def_tune_para.pad_tune, |
| &host->base->pad_tune); |
| } else { |
| writel(host->saved_tune_para.iocon, &host->base->msdc_iocon); |
| writel(host->saved_tune_para.pad_tune, |
| &host->base->pad_tune); |
| } |
| |
| dev_dbg(dev, "sclk: %d, timing: %d\n", host->sclk, timing); |
| } |
| |
| static int msdc_ops_set_ios(struct udevice *dev) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| uint clock = mmc->clock; |
| |
| msdc_set_buswidth(host, mmc->bus_width); |
| |
| if (mmc->clk_disable) |
| clock = 0; |
| else if (clock < mmc->cfg->f_min) |
| clock = mmc->cfg->f_min; |
| |
| if (host->mclk != clock || host->timing != mmc->selected_mode) |
| msdc_set_mclk(dev, host, mmc->selected_mode, clock); |
| |
| return 0; |
| } |
| |
| static int msdc_ops_get_cd(struct udevice *dev) |
| { |
| struct msdc_host *host = dev_get_priv(dev); |
| u32 val; |
| |
| if (host->builtin_cd) { |
| val = readl(&host->base->msdc_ps); |
| val = !!(val & MSDC_PS_CDSTS); |
| |
| return !val ^ host->cd_active_high; |
| } |
| |
| #if CONFIG_IS_ENABLED(DM_GPIO) |
| if (!host->gpio_cd.dev) |
| return 1; |
| |
| return dm_gpio_get_value(&host->gpio_cd); |
| #else |
| return 1; |
| #endif |
| } |
| |
| static int msdc_ops_get_wp(struct udevice *dev) |
| { |
| #if CONFIG_IS_ENABLED(DM_GPIO) |
| struct msdc_host *host = dev_get_priv(dev); |
| |
| if (!host->gpio_wp.dev) |
| return 0; |
| |
| return !dm_gpio_get_value(&host->gpio_wp); |
| #else |
| return 0; |
| #endif |
| } |
| |
| #ifdef MMC_SUPPORTS_TUNING |
| static u32 test_delay_bit(u32 delay, u32 bit) |
| { |
| bit %= PAD_DELAY_MAX; |
| return delay & (1 << bit); |
| } |
| |
| static int get_delay_len(u32 delay, u32 start_bit) |
| { |
| int i; |
| |
| for (i = 0; i < (PAD_DELAY_MAX - start_bit); i++) { |
| if (test_delay_bit(delay, start_bit + i) == 0) |
| return i; |
| } |
| |
| return PAD_DELAY_MAX - start_bit; |
| } |
| |
| static struct msdc_delay_phase get_best_delay(struct udevice *dev, |
| struct msdc_host *host, u32 delay) |
| { |
| int start = 0, len = 0; |
| int start_final = 0, len_final = 0; |
| u8 final_phase = 0xff; |
| struct msdc_delay_phase delay_phase = { 0, }; |
| |
| if (delay == 0) { |
| dev_err(dev, "phase error: [map:%x]\n", delay); |
| delay_phase.final_phase = final_phase; |
| return delay_phase; |
| } |
| |
| while (start < PAD_DELAY_MAX) { |
| len = get_delay_len(delay, start); |
| if (len_final < len) { |
| start_final = start; |
| len_final = len; |
| } |
| |
| start += len ? len : 1; |
| if (len >= 12 && start_final < 4) |
| break; |
| } |
| |
| /* The rule is to find the smallest delay cell */ |
| if (start_final == 0) |
| final_phase = (start_final + len_final / 3) % PAD_DELAY_MAX; |
| else |
| final_phase = (start_final + len_final / 2) % PAD_DELAY_MAX; |
| |
| dev_info(dev, "phase: [map:%x] [maxlen:%d] [final:%d]\n", |
| delay, len_final, final_phase); |
| |
| delay_phase.maxlen = len_final; |
| delay_phase.start = start_final; |
| delay_phase.final_phase = final_phase; |
| return delay_phase; |
| } |
| |
| static inline void msdc_set_cmd_delay(struct msdc_host *host, u32 value) |
| { |
| void __iomem *tune_reg = &host->base->pad_tune; |
| |
| if (host->dev_comp->pad_tune0) |
| tune_reg = &host->base->pad_tune0; |
| |
| if (host->top_base) |
| clrsetbits_le32(&host->top_base->emmc_top_cmd, PAD_CMD_RXDLY, |
| value << PAD_CMD_RXDLY_S); |
| else |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRDLY_M, |
| value << MSDC_PAD_TUNE_CMDRDLY_S); |
| } |
| |
| static inline void msdc_set_data_delay(struct msdc_host *host, u32 value) |
| { |
| void __iomem *tune_reg = &host->base->pad_tune; |
| |
| if (host->dev_comp->pad_tune0) |
| tune_reg = &host->base->pad_tune0; |
| |
| if (host->top_base) |
| clrsetbits_le32(&host->top_base->emmc_top_control, |
| PAD_DAT_RD_RXDLY, value << PAD_DAT_RD_RXDLY_S); |
| else |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATRRDLY_M, |
| value << MSDC_PAD_TUNE_DATRRDLY_S); |
| } |
| |
| static int hs400_tune_response(struct udevice *dev, u32 opcode) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| u32 cmd_delay = 0; |
| struct msdc_delay_phase final_cmd_delay = { 0, }; |
| u8 final_delay; |
| void __iomem *tune_reg = &host->base->pad_cmd_tune; |
| int cmd_err; |
| int i, j; |
| |
| setbits_le32(&host->base->pad_cmd_tune, BIT(0)); |
| |
| if (mmc->selected_mode == MMC_HS_200 || |
| mmc->selected_mode == UHS_SDR104) |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRRDLY_M, |
| host->hs200_cmd_int_delay << |
| MSDC_PAD_TUNE_CMDRRDLY_S); |
| |
| if (host->r_smpl) |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| else |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, PAD_CMD_TUNE_RX_DLY3, |
| i << PAD_CMD_TUNE_RX_DLY3_S); |
| |
| for (j = 0; j < 3; j++) { |
| mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!cmd_err) { |
| cmd_delay |= (1 << i); |
| } else { |
| cmd_delay &= ~(1 << i); |
| break; |
| } |
| } |
| } |
| |
| final_cmd_delay = get_best_delay(dev, host, cmd_delay); |
| clrsetbits_le32(tune_reg, PAD_CMD_TUNE_RX_DLY3, |
| final_cmd_delay.final_phase << |
| PAD_CMD_TUNE_RX_DLY3_S); |
| final_delay = final_cmd_delay.final_phase; |
| |
| dev_info(dev, "Final cmd pad delay: %x\n", final_delay); |
| return final_delay == 0xff ? -EIO : 0; |
| } |
| |
| static int msdc_tune_response(struct udevice *dev, u32 opcode) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| u32 rise_delay = 0, fall_delay = 0; |
| struct msdc_delay_phase final_rise_delay, final_fall_delay = { 0, }; |
| struct msdc_delay_phase internal_delay_phase; |
| u8 final_delay, final_maxlen; |
| u32 internal_delay = 0; |
| void __iomem *tune_reg = &host->base->pad_tune; |
| int cmd_err; |
| int i, j; |
| |
| if (host->dev_comp->pad_tune0) |
| tune_reg = &host->base->pad_tune0; |
| |
| if (mmc->selected_mode == MMC_HS_200 || |
| mmc->selected_mode == UHS_SDR104) |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRRDLY_M, |
| host->hs200_cmd_int_delay << |
| MSDC_PAD_TUNE_CMDRRDLY_S); |
| |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRDLY_M, |
| i << MSDC_PAD_TUNE_CMDRDLY_S); |
| |
| for (j = 0; j < 3; j++) { |
| mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!cmd_err) { |
| rise_delay |= (1 << i); |
| } else { |
| rise_delay &= ~(1 << i); |
| break; |
| } |
| } |
| } |
| |
| final_rise_delay = get_best_delay(dev, host, rise_delay); |
| /* if rising edge has enough margin, do not scan falling edge */ |
| if (final_rise_delay.maxlen >= 12 || |
| (final_rise_delay.start == 0 && final_rise_delay.maxlen >= 4)) |
| goto skip_fall; |
| |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRDLY_M, |
| i << MSDC_PAD_TUNE_CMDRDLY_S); |
| |
| for (j = 0; j < 3; j++) { |
| mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!cmd_err) { |
| fall_delay |= (1 << i); |
| } else { |
| fall_delay &= ~(1 << i); |
| break; |
| } |
| } |
| } |
| |
| final_fall_delay = get_best_delay(dev, host, fall_delay); |
| |
| skip_fall: |
| final_maxlen = max(final_rise_delay.maxlen, final_fall_delay.maxlen); |
| if (final_maxlen == final_rise_delay.maxlen) { |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRDLY_M, |
| final_rise_delay.final_phase << |
| MSDC_PAD_TUNE_CMDRDLY_S); |
| final_delay = final_rise_delay.final_phase; |
| } else { |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRDLY_M, |
| final_fall_delay.final_phase << |
| MSDC_PAD_TUNE_CMDRDLY_S); |
| final_delay = final_fall_delay.final_phase; |
| } |
| |
| if (host->dev_comp->async_fifo || host->hs200_cmd_int_delay) |
| goto skip_internal; |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRRDLY_M, |
| i << MSDC_PAD_TUNE_CMDRRDLY_S); |
| |
| mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!cmd_err) |
| internal_delay |= (1 << i); |
| } |
| |
| dev_dbg(dev, "Final internal delay: 0x%x\n", internal_delay); |
| |
| internal_delay_phase = get_best_delay(dev, host, internal_delay); |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CMDRRDLY_M, |
| internal_delay_phase.final_phase << |
| MSDC_PAD_TUNE_CMDRRDLY_S); |
| |
| skip_internal: |
| dev_dbg(dev, "Final cmd pad delay: %x\n", final_delay); |
| return final_delay == 0xff ? -EIO : 0; |
| } |
| |
| static int msdc_tune_data(struct udevice *dev, u32 opcode) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| u32 rise_delay = 0, fall_delay = 0; |
| struct msdc_delay_phase final_rise_delay, final_fall_delay = { 0, }; |
| u8 final_delay, final_maxlen; |
| void __iomem *tune_reg = &host->base->pad_tune; |
| int cmd_err; |
| int i, ret; |
| |
| if (host->dev_comp->pad_tune0) |
| tune_reg = &host->base->pad_tune0; |
| |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATRRDLY_M, |
| i << MSDC_PAD_TUNE_DATRRDLY_S); |
| |
| ret = mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!ret) { |
| rise_delay |= (1 << i); |
| } else if (cmd_err) { |
| /* in this case, retune response is needed */ |
| ret = msdc_tune_response(dev, opcode); |
| if (ret) |
| break; |
| } |
| } |
| |
| final_rise_delay = get_best_delay(dev, host, rise_delay); |
| if (final_rise_delay.maxlen >= 12 || |
| (final_rise_delay.start == 0 && final_rise_delay.maxlen >= 4)) |
| goto skip_fall; |
| |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATRRDLY_M, |
| i << MSDC_PAD_TUNE_DATRRDLY_S); |
| |
| ret = mmc_send_tuning(mmc, opcode, &cmd_err); |
| if (!ret) { |
| fall_delay |= (1 << i); |
| } else if (cmd_err) { |
| /* in this case, retune response is needed */ |
| ret = msdc_tune_response(dev, opcode); |
| if (ret) |
| break; |
| } |
| } |
| |
| final_fall_delay = get_best_delay(dev, host, fall_delay); |
| |
| skip_fall: |
| final_maxlen = max(final_rise_delay.maxlen, final_fall_delay.maxlen); |
| if (final_maxlen == final_rise_delay.maxlen) { |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATRRDLY_M, |
| final_rise_delay.final_phase << |
| MSDC_PAD_TUNE_DATRRDLY_S); |
| final_delay = final_rise_delay.final_phase; |
| } else { |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATRRDLY_M, |
| final_fall_delay.final_phase << |
| MSDC_PAD_TUNE_DATRRDLY_S); |
| final_delay = final_fall_delay.final_phase; |
| } |
| |
| if (mmc->selected_mode == MMC_HS_200 || |
| mmc->selected_mode == UHS_SDR104) |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_DATWRDLY_M, |
| host->hs200_write_int_delay << |
| MSDC_PAD_TUNE_DATWRDLY_S); |
| |
| dev_dbg(dev, "Final data pad delay: %x\n", final_delay); |
| |
| return final_delay == 0xff ? -EIO : 0; |
| } |
| |
| /* |
| * MSDC IP which supports data tune + async fifo can do CMD/DAT tune |
| * together, which can save the tuning time. |
| */ |
| static int msdc_tune_together(struct udevice *dev, u32 opcode) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| u32 rise_delay = 0, fall_delay = 0; |
| struct msdc_delay_phase final_rise_delay, final_fall_delay = { 0, }; |
| u8 final_delay, final_maxlen; |
| int i, ret; |
| |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| msdc_set_cmd_delay(host, i); |
| msdc_set_data_delay(host, i); |
| ret = mmc_send_tuning(mmc, opcode, NULL); |
| if (!ret) |
| rise_delay |= (1 << i); |
| } |
| |
| final_rise_delay = get_best_delay(dev, host, rise_delay); |
| if (final_rise_delay.maxlen >= 12 || |
| (final_rise_delay.start == 0 && final_rise_delay.maxlen >= 4)) |
| goto skip_fall; |
| |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| |
| for (i = 0; i < PAD_DELAY_MAX; i++) { |
| msdc_set_cmd_delay(host, i); |
| msdc_set_data_delay(host, i); |
| ret = mmc_send_tuning(mmc, opcode, NULL); |
| if (!ret) |
| fall_delay |= (1 << i); |
| } |
| |
| final_fall_delay = get_best_delay(dev, host, fall_delay); |
| |
| skip_fall: |
| final_maxlen = max(final_rise_delay.maxlen, final_fall_delay.maxlen); |
| if (final_maxlen == final_rise_delay.maxlen) { |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| final_delay = final_rise_delay.final_phase; |
| } else { |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_DSPL); |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_W_DSPL); |
| final_delay = final_fall_delay.final_phase; |
| } |
| |
| msdc_set_cmd_delay(host, final_delay); |
| msdc_set_data_delay(host, final_delay); |
| |
| dev_info(dev, "Final pad delay: %x\n", final_delay); |
| return final_delay == 0xff ? -EIO : 0; |
| } |
| |
| static int msdc_execute_tuning(struct udevice *dev, uint opcode) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc *mmc = &plat->mmc; |
| int ret = 0; |
| |
| if (host->dev_comp->data_tune && host->dev_comp->async_fifo) { |
| ret = msdc_tune_together(dev, opcode); |
| if (ret == -EIO) { |
| dev_err(dev, "Tune fail!\n"); |
| return ret; |
| } |
| |
| if (mmc->selected_mode == MMC_HS_400) { |
| clrbits_le32(&host->base->msdc_iocon, |
| MSDC_IOCON_DSPL | MSDC_IOCON_W_DSPL); |
| clrsetbits_le32(&host->base->pad_tune, |
| MSDC_PAD_TUNE_DATRRDLY_M, 0); |
| |
| writel(host->hs400_ds_delay, &host->base->pad_ds_tune); |
| /* for hs400 mode it must be set to 0 */ |
| clrbits_le32(&host->base->patch_bit2, |
| MSDC_PB2_CFGCRCSTS); |
| host->hs400_mode = true; |
| } |
| goto tune_done; |
| } |
| |
| if (mmc->selected_mode == MMC_HS_400) |
| ret = hs400_tune_response(dev, opcode); |
| else |
| ret = msdc_tune_response(dev, opcode); |
| if (ret == -EIO) { |
| dev_err(dev, "Tune response fail!\n"); |
| return ret; |
| } |
| |
| if (mmc->selected_mode != MMC_HS_400) { |
| ret = msdc_tune_data(dev, opcode); |
| if (ret == -EIO) { |
| dev_err(dev, "Tune data fail!\n"); |
| return ret; |
| } |
| } |
| |
| tune_done: |
| host->saved_tune_para.iocon = readl(&host->base->msdc_iocon); |
| host->saved_tune_para.pad_tune = readl(&host->base->pad_tune); |
| host->saved_tune_para.pad_cmd_tune = readl(&host->base->pad_cmd_tune); |
| |
| return ret; |
| } |
| #endif |
| |
| static void msdc_init_hw(struct msdc_host *host) |
| { |
| u32 val; |
| void __iomem *tune_reg = &host->base->pad_tune; |
| void __iomem *rd_dly0_reg = &host->base->pad_tune0; |
| void __iomem *rd_dly1_reg = &host->base->pad_tune1; |
| |
| if (host->dev_comp->pad_tune0) { |
| tune_reg = &host->base->pad_tune0; |
| rd_dly0_reg = &host->base->dat_rd_dly[0]; |
| rd_dly1_reg = &host->base->dat_rd_dly[1]; |
| } |
| |
| /* Configure to MMC/SD mode, clock free running */ |
| setbits_le32(&host->base->msdc_cfg, MSDC_CFG_MODE); |
| |
| /* Use PIO mode */ |
| setbits_le32(&host->base->msdc_cfg, MSDC_CFG_PIO); |
| |
| /* Reset */ |
| msdc_reset_hw(host); |
| |
| /* Enable/disable hw card detection according to fdt option */ |
| if (host->builtin_cd) |
| clrsetbits_le32(&host->base->msdc_ps, |
| MSDC_PS_CDDBCE_M, |
| (DEFAULT_CD_DEBOUNCE << MSDC_PS_CDDBCE_S) | |
| MSDC_PS_CDEN); |
| else |
| clrbits_le32(&host->base->msdc_ps, MSDC_PS_CDEN); |
| |
| /* Clear all interrupts */ |
| val = readl(&host->base->msdc_int); |
| writel(val, &host->base->msdc_int); |
| |
| /* Enable data & cmd interrupts */ |
| writel(DATA_INTS_MASK | CMD_INTS_MASK, &host->base->msdc_inten); |
| |
| writel(0, tune_reg); |
| writel(0, &host->base->msdc_iocon); |
| |
| if (host->r_smpl) |
| setbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| else |
| clrbits_le32(&host->base->msdc_iocon, MSDC_IOCON_RSPL); |
| |
| writel(0x403c0046, &host->base->patch_bit0); |
| writel(0xffff4089, &host->base->patch_bit1); |
| |
| if (host->dev_comp->stop_clk_fix) |
| clrsetbits_le32(&host->base->patch_bit1, MSDC_PB1_STOP_DLY_M, |
| 3 << MSDC_PB1_STOP_DLY_S); |
| |
| if (host->dev_comp->busy_check) |
| clrbits_le32(&host->base->patch_bit1, (1 << 7)); |
| |
| setbits_le32(&host->base->emmc50_cfg0, EMMC50_CFG_CFCSTS_SEL); |
| |
| if (host->dev_comp->async_fifo) { |
| clrsetbits_le32(&host->base->patch_bit2, MSDC_PB2_RESPWAIT_M, |
| 3 << MSDC_PB2_RESPWAIT_S); |
| |
| if (host->dev_comp->enhance_rx) { |
| if (host->top_base) |
| setbits_le32(&host->top_base->emmc_top_control, |
| SDC_RX_ENH_EN); |
| else |
| setbits_le32(&host->base->sdc_adv_cfg0, |
| SDC_RX_ENHANCE_EN); |
| } else { |
| clrsetbits_le32(&host->base->patch_bit2, |
| MSDC_PB2_RESPSTSENSEL_M, |
| 2 << MSDC_PB2_RESPSTSENSEL_S); |
| clrsetbits_le32(&host->base->patch_bit2, |
| MSDC_PB2_CRCSTSENSEL_M, |
| 2 << MSDC_PB2_CRCSTSENSEL_S); |
| } |
| |
| /* use async fifo to avoid tune internal delay */ |
| clrbits_le32(&host->base->patch_bit2, |
| MSDC_PB2_CFGRESP); |
| clrbits_le32(&host->base->patch_bit2, |
| MSDC_PB2_CFGCRCSTS); |
| } |
| |
| if (host->dev_comp->data_tune) { |
| setbits_le32(tune_reg, |
| MSDC_PAD_TUNE_RD_SEL | MSDC_PAD_TUNE_CMD_SEL); |
| clrsetbits_le32(&host->base->patch_bit0, |
| MSDC_INT_DAT_LATCH_CK_SEL_M, |
| host->latch_ck << |
| MSDC_INT_DAT_LATCH_CK_SEL_S); |
| } else { |
| /* choose clock tune */ |
| setbits_le32(tune_reg, MSDC_PAD_TUNE_RXDLYSEL); |
| } |
| |
| if (host->dev_comp->builtin_pad_ctrl) { |
| /* Set pins driving strength */ |
| writel(MSDC_PAD_CTRL0_CLKPD | MSDC_PAD_CTRL0_CLKSMT | |
| MSDC_PAD_CTRL0_CLKIES | (4 << MSDC_PAD_CTRL0_CLKDRVN_S) | |
| (4 << MSDC_PAD_CTRL0_CLKDRVP_S), &host->base->pad_ctrl0); |
| writel(MSDC_PAD_CTRL1_CMDPU | MSDC_PAD_CTRL1_CMDSMT | |
| MSDC_PAD_CTRL1_CMDIES | (4 << MSDC_PAD_CTRL1_CMDDRVN_S) | |
| (4 << MSDC_PAD_CTRL1_CMDDRVP_S), &host->base->pad_ctrl1); |
| writel(MSDC_PAD_CTRL2_DATPU | MSDC_PAD_CTRL2_DATSMT | |
| MSDC_PAD_CTRL2_DATIES | (4 << MSDC_PAD_CTRL2_DATDRVN_S) | |
| (4 << MSDC_PAD_CTRL2_DATDRVP_S), &host->base->pad_ctrl2); |
| } |
| |
| if (host->dev_comp->default_pad_dly) { |
| /* Default pad delay may be needed if tuning not enabled */ |
| clrsetbits_le32(tune_reg, MSDC_PAD_TUNE_CLKTDLY_M | |
| MSDC_PAD_TUNE_CMDRRDLY_M | |
| MSDC_PAD_TUNE_CMDRDLY_M | |
| MSDC_PAD_TUNE_DATRRDLY_M | |
| MSDC_PAD_TUNE_DATWRDLY_M, |
| (0x10 << MSDC_PAD_TUNE_CLKTDLY_S) | |
| (0x10 << MSDC_PAD_TUNE_CMDRRDLY_S) | |
| (0x10 << MSDC_PAD_TUNE_CMDRDLY_S) | |
| (0x10 << MSDC_PAD_TUNE_DATRRDLY_S) | |
| (0x10 << MSDC_PAD_TUNE_DATWRDLY_S)); |
| |
| writel((0x10 << MSDC_PAD_TUNE0_DAT0RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE0_DAT1RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE0_DAT2RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE0_DAT3RDDLY_S), |
| rd_dly0_reg); |
| |
| writel((0x10 << MSDC_PAD_TUNE1_DAT4RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE1_DAT5RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE1_DAT6RDDLY_S) | |
| (0x10 << MSDC_PAD_TUNE1_DAT7RDDLY_S), |
| rd_dly1_reg); |
| } |
| |
| /* Configure to enable SDIO mode otherwise sdio cmd5 won't work */ |
| setbits_le32(&host->base->sdc_cfg, SDC_CFG_SDIO); |
| |
| /* disable detecting SDIO device interrupt function */ |
| clrbits_le32(&host->base->sdc_cfg, SDC_CFG_SDIOIDE); |
| |
| /* Configure to default data timeout */ |
| clrsetbits_le32(&host->base->sdc_cfg, SDC_CFG_DTOC_M, |
| 3 << SDC_CFG_DTOC_S); |
| |
| if (host->dev_comp->stop_clk_fix) { |
| clrbits_le32(&host->base->sdc_fifo_cfg, |
| SDC_FIFO_CFG_WRVALIDSEL); |
| clrbits_le32(&host->base->sdc_fifo_cfg, |
| SDC_FIFO_CFG_RDVALIDSEL); |
| } |
| |
| host->def_tune_para.iocon = readl(&host->base->msdc_iocon); |
| host->def_tune_para.pad_tune = readl(&host->base->pad_tune); |
| } |
| |
| static void msdc_ungate_clock(struct msdc_host *host) |
| { |
| clk_enable(&host->src_clk); |
| clk_enable(&host->h_clk); |
| if (host->src_clk_cg.dev) |
| clk_enable(&host->src_clk_cg); |
| } |
| |
| static int msdc_drv_probe(struct udevice *dev) |
| { |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc_config *cfg = &plat->cfg; |
| |
| cfg->name = dev->name; |
| |
| host->dev_comp = (struct msdc_compatible *)dev_get_driver_data(dev); |
| |
| host->src_clk_freq = clk_get_rate(&host->src_clk); |
| |
| if (host->dev_comp->clk_div_bits == 8) |
| cfg->f_min = host->src_clk_freq / (4 * 255); |
| else |
| cfg->f_min = host->src_clk_freq / (4 * 4095); |
| |
| if (cfg->f_min < MIN_BUS_CLK) |
| cfg->f_min = MIN_BUS_CLK; |
| |
| if (cfg->f_max < cfg->f_min || cfg->f_max > host->src_clk_freq) |
| cfg->f_max = host->src_clk_freq; |
| |
| cfg->b_max = 1024; |
| cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; |
| |
| host->mmc = &plat->mmc; |
| host->timeout_ns = 100000000; |
| host->timeout_clks = 3 * (1 << SCLK_CYCLES_SHIFT); |
| |
| #ifdef CONFIG_PINCTRL |
| pinctrl_select_state(dev, "default"); |
| #endif |
| |
| msdc_ungate_clock(host); |
| msdc_init_hw(host); |
| |
| upriv->mmc = &plat->mmc; |
| |
| return 0; |
| } |
| |
| static int msdc_of_to_plat(struct udevice *dev) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| struct msdc_host *host = dev_get_priv(dev); |
| struct mmc_config *cfg = &plat->cfg; |
| fdt_addr_t base, top_base; |
| int ret; |
| |
| base = dev_read_addr(dev); |
| if (base == FDT_ADDR_T_NONE) |
| return -EINVAL; |
| host->base = map_sysmem(base, 0); |
| |
| top_base = dev_read_addr_index(dev, 1); |
| if (top_base == FDT_ADDR_T_NONE) |
| host->top_base = NULL; |
| else |
| host->top_base = map_sysmem(top_base, 0); |
| |
| ret = mmc_of_parse(dev, cfg); |
| if (ret) |
| return ret; |
| |
| ret = clk_get_by_name(dev, "source", &host->src_clk); |
| if (ret < 0) |
| return ret; |
| |
| ret = clk_get_by_name(dev, "hclk", &host->h_clk); |
| if (ret < 0) |
| return ret; |
| |
| clk_get_by_name(dev, "source_cg", &host->src_clk_cg); /* optional */ |
| |
| #if CONFIG_IS_ENABLED(DM_GPIO) |
| gpio_request_by_name(dev, "wp-gpios", 0, &host->gpio_wp, GPIOD_IS_IN); |
| gpio_request_by_name(dev, "cd-gpios", 0, &host->gpio_cd, GPIOD_IS_IN); |
| #endif |
| |
| host->hs400_ds_delay = dev_read_u32_default(dev, "hs400-ds-delay", 0); |
| host->hs200_cmd_int_delay = |
| dev_read_u32_default(dev, "cmd_int_delay", 0); |
| host->hs200_write_int_delay = |
| dev_read_u32_default(dev, "write_int_delay", 0); |
| host->latch_ck = dev_read_u32_default(dev, "latch-ck", 0); |
| host->r_smpl = dev_read_u32_default(dev, "r_smpl", 0); |
| host->builtin_cd = dev_read_u32_default(dev, "builtin-cd", 0); |
| host->cd_active_high = dev_read_bool(dev, "cd-active-high"); |
| |
| return 0; |
| } |
| |
| static int msdc_drv_bind(struct udevice *dev) |
| { |
| struct msdc_plat *plat = dev_get_plat(dev); |
| |
| return mmc_bind(dev, &plat->mmc, &plat->cfg); |
| } |
| |
| static int msdc_ops_wait_dat0(struct udevice *dev, int state, int timeout_us) |
| { |
| struct msdc_host *host = dev_get_priv(dev); |
| int ret; |
| u32 reg; |
| |
| ret = readl_poll_sleep_timeout(&host->base->msdc_ps, reg, |
| !!(reg & MSDC_PS_DAT0) == !!state, |
| 1000, /* 1 ms */ |
| timeout_us); |
| |
| return ret; |
| } |
| |
| static const struct dm_mmc_ops msdc_ops = { |
| .send_cmd = msdc_ops_send_cmd, |
| .set_ios = msdc_ops_set_ios, |
| .get_cd = msdc_ops_get_cd, |
| .get_wp = msdc_ops_get_wp, |
| #ifdef MMC_SUPPORTS_TUNING |
| .execute_tuning = msdc_execute_tuning, |
| #endif |
| .wait_dat0 = msdc_ops_wait_dat0, |
| }; |
| |
| static const struct msdc_compatible mt7620_compat = { |
| .clk_div_bits = 8, |
| .pad_tune0 = false, |
| .async_fifo = false, |
| .data_tune = false, |
| .busy_check = false, |
| .stop_clk_fix = false, |
| .enhance_rx = false, |
| .builtin_pad_ctrl = true, |
| .default_pad_dly = true, |
| }; |
| |
| static const struct msdc_compatible mt7622_compat = { |
| .clk_div_bits = 12, |
| .pad_tune0 = true, |
| .async_fifo = true, |
| .data_tune = true, |
| .busy_check = true, |
| .stop_clk_fix = true, |
| }; |
| |
| static const struct msdc_compatible mt7623_compat = { |
| .clk_div_bits = 12, |
| .pad_tune0 = true, |
| .async_fifo = true, |
| .data_tune = true, |
| .busy_check = false, |
| .stop_clk_fix = false, |
| .enhance_rx = false |
| }; |
| |
| static const struct msdc_compatible mt8512_compat = { |
| .clk_div_bits = 12, |
| .pad_tune0 = true, |
| .async_fifo = true, |
| .data_tune = true, |
| .busy_check = true, |
| .stop_clk_fix = true, |
| }; |
| |
| static const struct msdc_compatible mt8516_compat = { |
| .clk_div_bits = 12, |
| .pad_tune0 = true, |
| .async_fifo = true, |
| .data_tune = true, |
| .busy_check = true, |
| .stop_clk_fix = true, |
| }; |
| |
| static const struct msdc_compatible mt8183_compat = { |
| .clk_div_bits = 12, |
| .pad_tune0 = true, |
| .async_fifo = true, |
| .data_tune = true, |
| .busy_check = true, |
| .stop_clk_fix = true, |
| }; |
| |
| static const struct udevice_id msdc_ids[] = { |
| { .compatible = "mediatek,mt7620-mmc", .data = (ulong)&mt7620_compat }, |
| { .compatible = "mediatek,mt7622-mmc", .data = (ulong)&mt7622_compat }, |
| { .compatible = "mediatek,mt7623-mmc", .data = (ulong)&mt7623_compat }, |
| { .compatible = "mediatek,mt8512-mmc", .data = (ulong)&mt8512_compat }, |
| { .compatible = "mediatek,mt8516-mmc", .data = (ulong)&mt8516_compat }, |
| { .compatible = "mediatek,mt8183-mmc", .data = (ulong)&mt8183_compat }, |
| {} |
| }; |
| |
| U_BOOT_DRIVER(mtk_sd_drv) = { |
| .name = "mtk_sd", |
| .id = UCLASS_MMC, |
| .of_match = msdc_ids, |
| .of_to_plat = msdc_of_to_plat, |
| .bind = msdc_drv_bind, |
| .probe = msdc_drv_probe, |
| .ops = &msdc_ops, |
| .plat_auto = sizeof(struct msdc_plat), |
| .priv_auto = sizeof(struct msdc_host), |
| }; |