| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * Copyright (C) STMicroelectronics 2017 - All Rights Reserved |
| * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics. |
| */ |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/stm32mp1-clks.h> |
| #include <dt-bindings/reset/stm32mp1-resets.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0>; |
| }; |
| |
| cpu1: cpu@1 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <1>; |
| }; |
| }; |
| |
| psci { |
| compatible = "arm,psci"; |
| method = "smc"; |
| cpu_off = <0x84000002>; |
| cpu_on = <0x84000003>; |
| }; |
| |
| aliases { |
| gpio0 = &gpioa; |
| gpio1 = &gpiob; |
| gpio2 = &gpioc; |
| gpio3 = &gpiod; |
| gpio4 = &gpioe; |
| gpio5 = &gpiof; |
| gpio6 = &gpiog; |
| gpio7 = &gpioh; |
| gpio8 = &gpioi; |
| gpio9 = &gpioj; |
| gpio10 = &gpiok; |
| serial0 = &usart1; |
| serial1 = &usart2; |
| serial2 = &usart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &usart6; |
| serial6 = &uart7; |
| serial7 = &uart8; |
| }; |
| |
| intc: interrupt-controller@a0021000 { |
| compatible = "arm,cortex-a7-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0xa0021000 0x1000>, |
| <0xa0022000 0x2000>; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| clocks { |
| clk_hse: clk-hse { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| }; |
| |
| clk_hsi: clk-hsi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <64000000>; |
| }; |
| |
| clk_lse: clk-lse { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <32768>; |
| }; |
| |
| clk_lsi: clk-lsi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <32000>; |
| }; |
| |
| clk_csi: clk-csi { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <4000000>; |
| }; |
| }; |
| |
| pm_domain { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32mp157c-pd"; |
| |
| pd_core_ret: core-ret-power-domain@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| #power-domain-cells = <0>; |
| label = "CORE-RETENTION"; |
| |
| pd_core: core-power-domain@2 { |
| reg = <2>; |
| #power-domain-cells = <0>; |
| label = "CORE"; |
| }; |
| }; |
| }; |
| |
| soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&intc>; |
| ranges; |
| |
| timers2: timer@40000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40000000 0x400>; |
| clocks = <&rcc TIM2_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@1 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers3: timer@40001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40001000 0x400>; |
| clocks = <&rcc TIM3_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@2 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers4: timer@40002000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40002000 0x400>; |
| clocks = <&rcc TIM4_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@3 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers5: timer@40003000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40003000 0x400>; |
| clocks = <&rcc TIM5_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@4 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <4>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers6: timer@40004000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40004000 0x400>; |
| clocks = <&rcc TIM6_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| timer@5 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <5>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers7: timer@40005000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40005000 0x400>; |
| clocks = <&rcc TIM7_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| timer@6 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <6>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers12: timer@40006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40006000 0x400>; |
| clocks = <&rcc TIM12_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@11 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <11>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers13: timer@40007000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40007000 0x400>; |
| clocks = <&rcc TIM13_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@12 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <12>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers14: timer@40008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x40008000 0x400>; |
| clocks = <&rcc TIM14_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@13 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <13>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer1: timer@40009000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x40009000 0x400>; |
| clocks = <&rcc LPTIM1_K>; |
| clock-names = "mux"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@0 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <0>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-lptimer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| usart2: serial@4000e000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x4000e000 0x400>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART2_K>; |
| status = "disabled"; |
| }; |
| |
| usart3: serial@4000f000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x4000f000 0x400>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART3_K>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@40010000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40010000 0x400>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART4_K>; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@40011000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40011000 0x400>; |
| interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART5_K>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@40012000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x40012000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C1_K>; |
| resets = <&rcc I2C1_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@40013000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x40013000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C2_K>; |
| resets = <&rcc I2C2_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@40014000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x40014000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C3_K>; |
| resets = <&rcc I2C3_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@40015000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x40015000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C5_K>; |
| resets = <&rcc I2C5_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| cec: cec@40016000 { |
| compatible = "st,stm32-cec"; |
| reg = <0x40016000 0x400>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc CEC_K>, <&clk_lse>; |
| clock-names = "cec", "hdmi-cec"; |
| status = "disabled"; |
| }; |
| |
| dac: dac@40017000 { |
| compatible = "st,stm32h7-dac-core"; |
| reg = <0x40017000 0x400>; |
| clocks = <&rcc DAC12>; |
| clock-names = "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| dac1: dac@1 { |
| compatible = "st,stm32-dac"; |
| #io-channels-cells = <1>; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| dac2: dac@2 { |
| compatible = "st,stm32-dac"; |
| #io-channels-cells = <1>; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| uart7: serial@40018000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40018000 0x400>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART7_K>; |
| status = "disabled"; |
| }; |
| |
| uart8: serial@40019000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x40019000 0x400>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc UART8_K>; |
| status = "disabled"; |
| }; |
| |
| timers1: timer@44000000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44000000 0x400>; |
| clocks = <&rcc TIM1_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@0 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers8: timer@44001000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44001000 0x400>; |
| clocks = <&rcc TIM8_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@7 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <7>; |
| status = "disabled"; |
| }; |
| }; |
| |
| usart6: serial@44003000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x44003000 0x400>; |
| interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART6_K>; |
| status = "disabled"; |
| }; |
| |
| timers15: timer@44006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44006000 0x400>; |
| clocks = <&rcc TIM15_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@14 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <14>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers16: timer@44007000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44007000 0x400>; |
| clocks = <&rcc TIM16_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| timer@15 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <15>; |
| status = "disabled"; |
| }; |
| }; |
| |
| timers17: timer@44008000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-timers"; |
| reg = <0x44008000 0x400>; |
| clocks = <&rcc TIM17_K>; |
| clock-names = "int"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm"; |
| status = "disabled"; |
| }; |
| |
| timer@16 { |
| compatible = "st,stm32h7-timer-trigger"; |
| reg = <16>; |
| status = "disabled"; |
| }; |
| }; |
| |
| dma1: dma@48000000 { |
| compatible = "st,stm32-dma"; |
| reg = <0x48000000 0x400>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc DMA1>; |
| #dma-cells = <4>; |
| st,mem2mem; |
| dma-requests = <8>; |
| }; |
| |
| dma2: dma@48001000 { |
| compatible = "st,stm32-dma"; |
| reg = <0x48001000 0x400>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc DMA2>; |
| #dma-cells = <4>; |
| st,mem2mem; |
| dma-requests = <8>; |
| }; |
| |
| dmamux1: dma-router@48002000 { |
| compatible = "st,stm32h7-dmamux"; |
| reg = <0x48002000 0x1c>; |
| #dma-cells = <3>; |
| dma-requests = <128>; |
| dma-masters = <&dma1 &dma2>; |
| dma-channels = <16>; |
| clocks = <&rcc DMAMUX>; |
| }; |
| |
| adc: adc@48003000 { |
| compatible = "st,stm32mp1-adc-core"; |
| reg = <0x48003000 0x400>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc ADC12>, <&rcc ADC12_K>; |
| clock-names = "bus", "adc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| adc1: adc@0 { |
| compatible = "st,stm32mp1-adc"; |
| #io-channel-cells = <1>; |
| reg = <0x0>; |
| interrupt-parent = <&adc>; |
| interrupts = <0>; |
| status = "disabled"; |
| }; |
| |
| adc2: adc@100 { |
| compatible = "st,stm32mp1-adc"; |
| #io-channel-cells = <1>; |
| reg = <0x100>; |
| interrupt-parent = <&adc>; |
| interrupts = <1>; |
| status = "disabled"; |
| }; |
| }; |
| |
| sdmmc3: sdmmc@48004000 { |
| compatible = "st,stm32-sdmmc2"; |
| reg = <0x48004000 0x400>, <0x48005000 0x400>; |
| reg-names = "sdmmc", "delay"; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>; |
| clocks = <&rcc SDMMC3_K>; |
| resets = <&rcc SDMMC3_R>; |
| st,idma = <1>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| usbotg_hs: usb-otg@49000000 { |
| compatible = "st,stm32mp1-hsotg", "snps,dwc2"; |
| reg = <0x49000000 0x10000>; |
| clocks = <&rcc USBO_K>; |
| clock-names = "otg"; |
| resets = <&rcc USBO_R>; |
| reset-names = "dwc2"; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| g-rx-fifo-size = <256>; |
| g-np-tx-fifo-size = <32>; |
| g-tx-fifo-size = <128 128 64 64 64 64 32 32>; |
| dr_mode = "otg"; |
| power-domains = <&pd_core>; |
| status = "disabled"; |
| }; |
| |
| rcc: rcc@50000000 { |
| compatible = "st,stm32mp1-rcc", "syscon"; |
| reg = <0x50000000 0x1000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| rcc_reboot: rcc-reboot@50000000 { |
| compatible = "syscon-reboot"; |
| regmap = <&rcc>; |
| offset = <0x404>; |
| mask = <0x1>; |
| }; |
| |
| pwr: pwr@50001000 { |
| compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd"; |
| reg = <0x50001000 0x400>; |
| system-power-controller; |
| interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>; |
| st,sysrcc = <&rcc>; |
| clocks = <&rcc PLL2_R>; |
| clock-names = "phyclk"; |
| |
| pwr-regulators@c { |
| compatible = "st,stm32mp1,pwr-reg"; |
| st,tzcr = <&rcc 0x0 0x1>; |
| |
| reg11: reg11 { |
| regulator-name = "reg11"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| reg18: reg18 { |
| regulator-name = "reg18"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| usb33: usb33 { |
| regulator-name = "usb33"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| }; |
| |
| exti: interrupt-controller@5000d000 { |
| compatible = "st,stm32mp1-exti", "syscon"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x5000d000 0x400>; |
| }; |
| |
| syscfg: system-config@50020000 { |
| compatible = "st,stm32-syscfg", "syscon"; |
| reg = <0x50020000 0x400>; |
| }; |
| |
| lptimer2: timer@50021000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50021000 0x400>; |
| clocks = <&rcc LPTIM2_K>; |
| clock-names = "mux"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@1 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <1>; |
| status = "disabled"; |
| }; |
| |
| counter { |
| compatible = "st,stm32-lptimer-counter"; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer3: timer@50022000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50022000 0x400>; |
| clocks = <&rcc LPTIM3_K>; |
| clock-names = "mux"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| trigger@2 { |
| compatible = "st,stm32-lptimer-trigger"; |
| reg = <2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer4: timer@50023000 { |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50023000 0x400>; |
| clocks = <&rcc LPTIM4_K>; |
| clock-names = "mux"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| lptimer5: timer@50024000 { |
| compatible = "st,stm32-lptimer"; |
| reg = <0x50024000 0x400>; |
| clocks = <&rcc LPTIM5_K>; |
| clock-names = "mux"; |
| status = "disabled"; |
| |
| pwm { |
| compatible = "st,stm32-pwm-lp"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| }; |
| |
| vrefbuf: vrefbuf@50025000 { |
| compatible = "st,stm32-vrefbuf"; |
| reg = <0x50025000 0x8>; |
| regulator-min-microvolt = <1500000>; |
| regulator-max-microvolt = <2500000>; |
| clocks = <&rcc VREF>; |
| status = "disabled"; |
| }; |
| |
| cryp1: cryp@54001000 { |
| compatible = "st,stm32mp1-cryp"; |
| reg = <0x54001000 0x400>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc CRYP1>; |
| resets = <&rcc CRYP1_R>; |
| status = "disabled"; |
| }; |
| |
| rng1: rng@54003000 { |
| compatible = "st,stm32-rng"; |
| reg = <0x54003000 0x400>; |
| clocks = <&rcc RNG1_K>; |
| resets = <&rcc RNG1_R>; |
| status = "disabled"; |
| }; |
| |
| mdma1: dma@58000000 { |
| compatible = "st,stm32h7-mdma"; |
| reg = <0x58000000 0x1000>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc MDMA>; |
| #dma-cells = <5>; |
| dma-channels = <32>; |
| dma-requests = <48>; |
| }; |
| |
| qspi: qspi@58003000 { |
| compatible = "st,stm32f469-qspi"; |
| reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; |
| reg-names = "qspi", "qspi_mm"; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc QSPI_K>; |
| resets = <&rcc QSPI_R>; |
| status = "disabled"; |
| }; |
| |
| sdmmc1: sdmmc@58005000 { |
| compatible = "st,stm32-sdmmc2"; |
| reg = <0x58005000 0x1000>, <0x58006000 0x1000>; |
| reg-names = "sdmmc", "delay"; |
| clocks = <&rcc SDMMC1_K>; |
| resets = <&rcc SDMMC1_R>; |
| st,idma = <1>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| sdmmc2: sdmmc@58007000 { |
| compatible = "st,stm32-sdmmc2"; |
| reg = <0x58007000 0x1000>, <0x58008000 0x1000>; |
| reg-names = "sdmmc", "delay"; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>; |
| clocks = <&rcc SDMMC2_K>; |
| resets = <&rcc SDMMC2_R>; |
| st,idma = <1>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <120000000>; |
| status = "disabled"; |
| }; |
| |
| crc1: crc@58009000 { |
| compatible = "st,stm32f7-crc"; |
| reg = <0x58009000 0x400>; |
| clocks = <&rcc CRC1>; |
| status = "disabled"; |
| }; |
| |
| usbh_ohci: usbh-ohci@5800c000 { |
| compatible = "generic-ohci"; |
| reg = <0x5800c000 0x1000>; |
| clocks = <&rcc USBH>; |
| resets = <&rcc USBH_R>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| usbh_ehci: usbh-ehci@5800d000 { |
| compatible = "generic-ehci"; |
| reg = <0x5800d000 0x1000>; |
| clocks = <&rcc USBH>; |
| resets = <&rcc USBH_R>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; |
| companion = <&usbh_ohci>; |
| status = "disabled"; |
| }; |
| |
| dsi: dsi@5a000000 { |
| compatible = "st,stm32-dsi"; |
| reg = <0x5a000000 0x800>; |
| clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>; |
| clock-names = "pclk", "ref", "px_clk"; |
| resets = <&rcc DSI_R>; |
| reset-names = "apb"; |
| status = "disabled"; |
| }; |
| |
| ltdc: display-controller@5a001000 { |
| compatible = "st,stm32-ltdc"; |
| reg = <0x5a001000 0x400>; |
| interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc LTDC_PX>; |
| clock-names = "lcd"; |
| resets = <&rcc LTDC_R>; |
| status = "disabled"; |
| }; |
| |
| usbphyc: usbphyc@5a006000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "st,stm32mp1-usbphyc"; |
| reg = <0x5a006000 0x1000>; |
| clocks = <&rcc USBPHY_K>; |
| resets = <&rcc USBPHY_R>; |
| status = "disabled"; |
| |
| usbphyc_port0: usb-phy@0 { |
| #phy-cells = <0>; |
| reg = <0>; |
| }; |
| |
| usbphyc_port1: usb-phy@1 { |
| #phy-cells = <1>; |
| reg = <1>; |
| }; |
| }; |
| |
| usart1: serial@5c000000 { |
| compatible = "st,stm32h7-uart"; |
| reg = <0x5c000000 0x400>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc USART1_K>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@5c002000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x5c002000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C4_K>; |
| resets = <&rcc I2C4_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@5c009000 { |
| compatible = "st,stm32f7-i2c"; |
| reg = <0x5c009000 0x400>; |
| interrupt-names = "event", "error"; |
| interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&rcc I2C6_K>; |
| resets = <&rcc I2C6_R>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| }; |