| # SPDX-License-Identifier: GPL-2.0+ |
| # |
| # Copyright (C) 2019, Pascal Linder <pascal.linder@edu.hefr.ch> |
| |
| config VENDOR_KM |
| bool |
| help |
| Selected by any KM board to have additional configurations. |
| |
| if VENDOR_KM |
| |
| menu "KM Board Setup" |
| |
| config KM_PNVRAM |
| hex "Pseudo RAM" |
| default 0x80000 |
| depends on !ARCH_SOCFPGA |
| help |
| Start address of the pseudo non-volatile RAM for application. |
| |
| config KM_PHRAM |
| hex "Physical RAM" |
| default 0x17F000 if ARM && !ARCH_LS1021A |
| default 0x100000 if PPC || ARCH_LS1021A |
| depends on !ARCH_SOCFPGA |
| help |
| Start address of the physical RAM, which is the mounted /var folder. |
| |
| config KM_RESERVED_PRAM |
| hex "Reserved RAM" |
| default 0x801000 if ARCH_KIRKWOOD |
| default 0x0 if MPC83xx |
| default 0x1000 if MPC85xx || ARCH_LS1021A |
| depends on !ARCH_SOCFPGA |
| help |
| Reserved physical RAM area at the end of memory for special purposes. |
| |
| config KM_CRAMFS_ADDR |
| hex "CRAMFS Address" |
| default 0x83000000 if ARCH_LS1021A |
| default 0x3000000 |
| depends on !ARCH_SOCFPGA |
| help |
| Start address of the CRAMFS containing the Linux kernel. |
| |
| config KM_KERNEL_ADDR |
| hex "Kernel Load Address" |
| default 0x82000000 if ARCH_LS1021A |
| default 0x2000000 |
| help |
| Address where to load Linux kernel in RAM. |
| |
| config KM_FDT_ADDR |
| hex "FDT Load Address" |
| default 0x82FC0000 if ARCH_LS1021A |
| default 0x2FC0000 |
| help |
| Address where to load flattened device tree in RAM. |
| |
| config SYS_PAX_BASE |
| hex "PAX IFC Base Address" |
| default 0x78000000 |
| depends on ARCH_LS1021A |
| help |
| IFC Base Address for PAXx FPGA. |
| |
| config SYS_CLIPS_BASE |
| hex "CLIPS IFC Base Address" |
| default 0x78000000 |
| depends on ARCH_LS1021A |
| help |
| IFC Base Address for CLIPS FPGA. |
| |
| config KM_CONSOLE_TTY |
| string "KM Console" |
| default "ttyS0" |
| help |
| TTY console to use on board. |
| |
| config KM_DEF_NETDEV |
| string "Default Netdevice" |
| default "eth0" |
| help |
| Default netdevice for debug interface |
| |
| config KM_COMMON_ETH_INIT |
| bool "Common Ethernet Initialization" |
| default y if ARCH_KIRKWOOD || MPC83xx |
| default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A |
| help |
| Use the Ethernet initialization implemented in common code that |
| detects if a Piggy board is present. |
| |
| config PIGGY_MAC_ADDRESS_OFFSET |
| int "Piggy Address Offset" |
| default 0 |
| help |
| MAC address offset for the Piggy board. |
| |
| config KM_MVEXTSW_ADDR |
| hex "Marvell Switch Address" |
| depends on MV88E6352_SWITCH |
| default 0x10 |
| help |
| Address of external Marvell switch. |
| |
| config KM_IVM_BUS |
| int "IVM I2C Bus" |
| default 0 if ARCH_SOCFPGA |
| default 1 if ARCH_KIRKWOOD || MPC85xx || ARCH_LS1021A |
| default 2 if MPC83xx |
| help |
| Identifier number of I2C bus, where the inventory EEPROM is connected to. |
| |
| config SYS_IVM_EEPROM_ADR |
| hex "IVM I2C Address" |
| default 0x50 |
| help |
| I2C address of the EEPROM containing the inventory. |
| |
| config SYS_IVM_EEPROM_MAX_LEN |
| hex "IVM Length" |
| default 0x400 |
| help |
| Maximum length of inventory in EEPROM. |
| |
| config SYS_IVM_EEPROM_PAGE_LEN |
| hex "IVM Page Size" |
| default 0x100 |
| help |
| Page size of inventory in EEPROM. |
| |
| config PG_WCOM_UBOOT_UPDATE_SUPPORTED |
| bool "Enable U-boot Field Fail-Safe Update Functionality" |
| default n |
| help |
| Indicates that field fail-safe u-boot update is supported. |
| This functionality works only for designs that are booting |
| from parallel NOR flash. |
| |
| config PG_WCOM_UBOOT_BOOTPACKAGE |
| bool "U-boot Is Part Of Factory Boot-Package Image" |
| default n |
| help |
| Indicates that u-boot will be a part of the factory programmed |
| boot-package image. |
| Has to be set for original u-boot programmed at factory. |
| |
| config PG_WCOM_UBOOT_UPDATE_TEXT_BASE |
| hex "Text Base For U-boot Programmed Outside Factory" |
| default 0xFFFFFFFF |
| help |
| Text base of an updated u-boot that is not factory programmed but |
| later when the unit is rolled out on the field. |
| Has to be set for original u-boot programmed at factory. |
| |
| config PG_WCOM_UBOOT_UPDATE |
| bool "U-boot Is Part Of Factory Boot-Package Image" |
| default n |
| help |
| Indicates that u-boot will be a part of the embedded software and |
| programmed at field. |
| Has to be set for updated u-boot version programmed at field. |
| |
| source "board/keymile/km83xx/Kconfig" |
| source "board/keymile/kmcent2/Kconfig" |
| source "board/keymile/km_arm/Kconfig" |
| source "board/keymile/pg-wcom-ls102xa/Kconfig" |
| |
| endmenu |
| |
| endif |