blob: 56530fd0720a9e2d6b369c8688563a6fd426d9fd [file] [log] [blame]
/*
* (C) Copyright 2015
* (C) Copyright 2014
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale i.MX6Q SabreSD board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __ARISTAINETOS_COMMON_CONFIG_H
#define __ARISTAINETOS_COMMON_CONFIG_H
#include "mx6_common.h"
#define CONFIG_MACH_TYPE 4501
#define CONFIG_MMCROOT "/dev/mmcblk0p1"
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (64 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MXC_UART
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_SPI_FLASH_MTD
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
/* Command definition */
#define CONFIG_CMD_BMODE
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=u-boot.scr\0" \
"fit_file=/boot/system.itb\0" \
"loadaddr=0x12000000\0" \
"fit_addr_r=0x14000000\0" \
"uboot=/boot/u-boot.imx\0" \
"uboot_sz=d0000\0" \
"rescue_sys_addr=f0000\0" \
"rescue_sys_length=f10000\0" \
"panel=lb07wv8\0" \
"splashpos=m,m\0" \
"console=" CONSOLE_DEV "\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
"default ${board_type}\0" \
"get_env=mw ${loadaddr} 0 0x20000;" \
"mmc rescan;" \
"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
"env import -t ${loadaddr}\0" \
"default_env=mw ${loadaddr} 0 0x20000;" \
"env export -t ${loadaddr} serial# ethaddr eth1addr " \
"board_type panel;" \
"env default -a;" \
"env import -t ${loadaddr}\0" \
"loadbootscript=" \
"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"mmcpart=1\0" \
"mmcdev=0\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs addmtd addmisc set_fit_default;" \
"bootm ${fit_addr_r}\0" \
"mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
"${fit_file}\0" \
"mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
"${uboot}\0" \
"mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
"setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
"setexpr uboot_maxsize ${uboot_sz} - 400;" \
"mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
"run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
"sf write ${loadaddr} 400 ${filesize};" \
"sf read ${cmp_buf} 400 ${uboot_sz};" \
"cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
"ubiboot=echo Booting from ubi ...; " \
"run ubiargs addmtd addmisc set_fit_default;" \
"bootm ${fit_addr_r}\0" \
"rescueargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/ram rw\0 " \
"rescueboot=echo Booting rescue system from NOR ...; " \
"run rescueargs addmtd addmisc set_fit_default;" \
"bootm ${fit_addr_r}\0" \
"rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
"${rescue_sys_length}; imi ${fit_addr_r}\0" \
CONFIG_EXTRA_ENV_BOARD_SETTINGS
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
"if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run mmc_load_fit; then " \
"run mmcboot; " \
"else " \
"if run ubifs_load_fit; then " \
"run ubiboot; " \
"else " \
"if run rescue_load_fit; then " \
"run rescueboot; " \
"else " \
"echo RESCUE SYSTEM BOOT " \
"FAILURE;" \
"fi; " \
"fi; " \
"fi; " \
"fi; " \
"else " \
"if run ubifs_load_fit; then " \
"run ubiboot; " \
"else " \
"if run rescue_load_fit; then " \
"run rescueboot; " \
"else " \
"echo RESCUE SYSTEM BOOT FAILURE;" \
"fi; " \
"fi; " \
"fi"
#define CONFIG_ARP_TIMEOUT 200UL
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000)
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
#define CONFIG_STACKSIZE (128 * 1024)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* Environment organization */
#define CONFIG_ENV_SIZE (12 * 1024)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SECT_SIZE (0x010000)
#define CONFIG_ENV_OFFSET (0x0d0000)
#define CONFIG_ENV_OFFSET_REDUND (0x0e0000)
#define CONFIG_SYS_FSL_USDHC_NUM 2
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7f
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x00} }
/* NAND stuff */
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8
/* RTC */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_RTC_BUS_NUM 2
#define CONFIG_RTC_M41T11
#define CONFIG_CMD_DATE
/* USB Configs */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
/* UBI support */
#define CONFIG_LZO
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define CONFIG_RBTREE
#define CONFIG_CMD_UBIFS
#define CONFIG_HW_WATCHDOG
#define CONFIG_IMX_WATCHDOG
/* Framebuffer */
#define CONFIG_VIDEO_IPUV3
/* check this console not needed, after test remove it */
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IPUV3_CLK 198000000
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_CMD_BMP
#define CONFIG_PWM_IMX
#define CONFIG_IMX6_PWM_PER_CLK 66000000
#endif /* __ARISTAINETOS_COMMON_CONFIG_H */