board/aries/m28evk/m28evk.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Aries M28 module
 *
 * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
 * on behalf of DENX Software Engineering GmbH
 */

#include <common.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux-mx28.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <linux/mii.h>
#include <miiphy.h>
#include <netdev.h>
#include <errno.h>

DECLARE_GLOBAL_DATA_PTR;

/*
 * Functions
 */
int board_early_init_f(void)
{
	/* IO0 clock at 480MHz */
	mxs_set_ioclk(MXC_IOCLK0, 480000);
	/* IO1 clock at 480MHz */
	mxs_set_ioclk(MXC_IOCLK1, 480000);

	/* SSP0 clock at 96MHz */
	mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
	/* SSP2 clock at 160MHz */
	mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);

#ifdef	CONFIG_CMD_USB
	mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
	mxs_iomux_setup_pad(MX28_PAD_AUART3_TX__GPIO_3_13 |
			MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
	gpio_direction_output(MX28_PAD_AUART3_TX__GPIO_3_13, 0);

	mxs_iomux_setup_pad(MX28_PAD_AUART3_RX__GPIO_3_12 |
			MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
	gpio_direction_output(MX28_PAD_AUART3_RX__GPIO_3_12, 0);
#endif

	return 0;
}

int board_init(void)
{
	/* Adress of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;

	return 0;
}

int dram_init(void)
{
	return mxs_dram_init();
}

#ifdef	CONFIG_CMD_MMC
static int m28_mmc_wp(int id)
{
	if (id != 0) {
		printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
		return 1;
	}

	return gpio_get_value(MX28_PAD_AUART2_CTS__GPIO_3_10);
}

int board_mmc_init(bd_t *bis)
{
	/* Configure WP as input. */
	gpio_direction_input(MX28_PAD_AUART2_CTS__GPIO_3_10);
	/* Turn on the power to the card. */
	gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);

	return mxsmmc_initialize(bis, 0, m28_mmc_wp, NULL);
}
#endif

#ifdef	CONFIG_CMD_NET

#define	MII_OPMODE_STRAP_OVERRIDE	0x16
#define	MII_PHY_CTRL1			0x1e
#define	MII_PHY_CTRL2			0x1f

int fecmxc_mii_postcall(int phy)
{
#if	defined(CONFIG_ARIES_M28_V11) || defined(CONFIG_ARIES_M28_V10)
	/* KZ8031 PHY on old boards. */
	const uint32_t freq = 0x0080;
#else
	/* KZ8021 PHY on new boards. */
	const uint32_t freq = 0x0000;
#endif

	miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
	miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
	if (phy == 3)
		miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8100 | freq);
	return 0;
}

int board_eth_init(bd_t *bis)
{
	struct mxs_clkctrl_regs *clkctrl_regs =
		(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
	struct eth_device *dev;
	int ret;

	ret = cpu_eth_init(bis);
	if (ret)
		return ret;

	clrsetbits_le32(&clkctrl_regs->hw_clkctrl_enet,
		CLKCTRL_ENET_TIME_SEL_MASK | CLKCTRL_ENET_CLK_OUT_EN,
		CLKCTRL_ENET_TIME_SEL_RMII_CLK);

#if !defined(CONFIG_ARIES_M28_V11) && !defined(CONFIG_ARIES_M28_V10)
	/* Reset the new PHY */
	gpio_direction_output(MX28_PAD_AUART2_RTS__GPIO_3_11, 0);
	udelay(10000);
	gpio_set_value(MX28_PAD_AUART2_RTS__GPIO_3_11, 1);
	udelay(10000);
#endif

	ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
	if (ret) {
		printf("FEC MXS: Unable to init FEC0\n");
		return ret;
	}

	ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
	if (ret) {
		printf("FEC MXS: Unable to init FEC1\n");
		return ret;
	}

	dev = eth_get_dev_by_name("FEC0");
	if (!dev) {
		printf("FEC MXS: Unable to get FEC0 device entry\n");
		return -EINVAL;
	}

	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
	if (ret) {
		printf("FEC MXS: Unable to register FEC0 mii postcall\n");
		return ret;
	}

	dev = eth_get_dev_by_name("FEC1");
	if (!dev) {
		printf("FEC MXS: Unable to get FEC1 device entry\n");
		return -EINVAL;
	}

	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
	if (ret) {
		printf("FEC MXS: Unable to register FEC1 mii postcall\n");
		return ret;
	}

	return ret;
}

#endif