include/configs/mx23_olinuxino.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) 2013 Marek Vasut <marex@denx.de>
 */
#ifndef __CONFIGS_MX23_OLINUXINO_H__
#define __CONFIGS_MX23_OLINUXINO_H__

/* U-Boot Commands */

/* Memory configuration */
#define PHYS_SDRAM_1			0x40000000	/* Base address */
#define PHYS_SDRAM_1_SIZE		0x08000000	/* Max 128 MB RAM */
#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1

/* Status LED */

/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_MXS_PORT0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif

/* Ethernet */

/* Booting Linux */
#define CONFIG_BOOTFILE		"uImage"

/* Extra Environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
	"update_sd_firmware_filename=u-boot.sd\0" \
	"update_sd_firmware="		/* Update the SD firmware partition */ \
		"if mmc rescan ; then "	\
		"if tftp ${update_sd_firmware_filename} ; then " \
		"setexpr fw_sz ${filesize} / 0x200 ; "	/* SD block size */ \
		"setexpr fw_sz ${fw_sz} + 1 ; "	\
		"mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
		"fi ; "	\
		"fi\0" \
	"script=boot.scr\0"	\
	"uimage=uImage\0" \
	"console=ttyAMA0\0" \
	"fdt_file=imx23-olinuxino.dtb\0" \
	"fdt_addr=0x41000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"mmcdev=0\0" \
	"mmcpart=2\0" \
	"mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
		"root=${mmcroot}\0" \
	"loadbootscript="  \
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; "	\
		"source\0" \
	"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
			"if run loadfdt; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi; " \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"usb start; " \
		"run netargs; "	\
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${uimage}; " \
		"if test ${boot_fdt} = yes; then " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"bootm ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"if test ${boot_fdt} = try; then " \
					"bootm; " \
				"else " \
					"echo WARN: Cannot load the DT; " \
				"fi;" \
			"fi; " \
		"else " \
			"bootm; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
		"if run loadbootscript; then " \
			"run bootscript; " \
		"else " \
			"if run loaduimage; then " \
				"run mmcboot; " \
			"else run netboot; " \
			"fi; " \
		"fi; " \
	"else run netboot; fi"

/* The rest of the configuration is shared */
#include <configs/mxs.h>

#endif /* __CONFIGS_MX23_OLINUXINO_H__ */