include/configs/IP860.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2000-2005
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
 #define CONFIG_IP860		1	/* ...on a IP860 board		*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 #define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/

 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/

 #define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \
 "\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0"

 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND							\
 	"bootp; "								\
 	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
 	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
 	"bootm"

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/


 /* enable I2C and select the hardware/software driver */
 #undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
 #define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
 /*
  * Software (bit-bang) I2C driver configuration
  */
 #define PB_SCL		0x00000020	/* PB 26 */
 #define PB_SDA		0x00000010	/* PB 27 */

 #define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
 #define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
 #define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
 #define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 #define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */


 # define CONFIG_SYS_I2C_SPEED		50000
 # define CONFIG_SYS_I2C_SLAVE		0xFE
 # define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"    */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* takes up to 10 msec */

 #define	CONFIG_TIMESTAMP		/* Print image info with timestamp */


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH

 /*
  * Miscellaneous configurable options
  */
 #define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
 #define	CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/

 #define	CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address	*/

 #define	CONFIG_SYS_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/

 #define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
 #define CONFIG_SYS_IMMR		0xF1000000	/* Non-standard value!!	*/

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define	CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
 #define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 #define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define	CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0x10000000
 #ifdef	DEBUG
 #define	CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
 #else
 #if 0 /* need more space for I2C tests */
 #define	CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
 #else
 #define	CONFIG_SYS_MONITOR_LEN		(256 << 10)
 #endif
 #endif
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	124	/* max number of sectors on one chip	*/

 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 #undef	CONFIG_ENV_IS_IN_FLASH
 #undef	CONFIG_ENV_IS_IN_NVRAM
 #undef  CONFIG_ENV_IS_IN_NVRAM
 #undef	DEBUG_I2C
 #define	CONFIG_ENV_IS_IN_EEPROM

 #ifdef	CONFIG_ENV_IS_IN_NVRAM
 #define CONFIG_ENV_ADDR		0x20000000	/* use SRAM	*/
 #define CONFIG_ENV_SIZE		(16<<10)	/* use 16 kB	*/
 #endif	/* CONFIG_ENV_IS_IN_NVRAM */

 #ifdef	CONFIG_ENV_IS_IN_EEPROM
 #define CONFIG_ENV_OFFSET		 512	/* Leave 512 bytes free for other data	*/
 #define CONFIG_ENV_SIZE		1536	/* Use remaining space			*/
 #endif	/* CONFIG_ENV_IS_IN_EEPROM */

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
 #endif
 #define CONFIG_SYS_DELAYED_ICACHE	1	/* enable ICache not before
 						 * running in RAM.
 						 */

 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control				11-9
  * SYPCR can only be written once after reset!
  *-----------------------------------------------------------------------
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  * +0x0004
  */
 #if defined(CONFIG_WATCHDOG)
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 #else
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 #endif

 /*-----------------------------------------------------------------------
  * SIUMCR - SIU Module Configuration				11-6
  *-----------------------------------------------------------------------
  * +0x0000 => 0x80600800
  */
 #define CONFIG_SYS_SIUMCR	(SIUMCR_EARB   | SIUMCR_EARP0 | \
 			 SIUMCR_DBGC11 | SIUMCR_MLRC10)

 /*-----------------------------------------------------------------------
  * Clock Setting - get clock frequency from Board Revision Register
  *-----------------------------------------------------------------------
  */
 #ifndef __ASSEMBLY__
 extern  unsigned long           ip860_get_clk_freq (void);
 #endif
 #define	CONFIG_8xx_GCLK_FREQ	ip860_get_clk_freq()

 /*-----------------------------------------------------------------------
  * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  * +0x0200 => 0x00C2
  */
 #define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

 /*-----------------------------------------------------------------------
  * PISCR - Periodic Interrupt Status and Control		11-31
  *-----------------------------------------------------------------------
  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
  * +0x0240 => 0x0082
  */
 #define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)

 /*-----------------------------------------------------------------------
  * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit, set PLL multiplication factor !
  */
 /* +0x0286 => was: 0x0000D000 */
 #define CONFIG_SYS_PLPRCR							\
 		(	PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST |	\
 			/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL |		\
 			PLPRCR_CSR   | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/	\
 		)

 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
  *-----------------------------------------------------------------------
  * Set clock output, timebase and RTC source and divider,
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
 #define CONFIG_SYS_SCCR	(SCCR_COM00	|   SCCR_TBS	  |	\
 			 SCCR_RTDIV	|   SCCR_RTSEL	  |	\
 			 /*SCCR_CRQEN|*/  /*SCCR_PRQEN|*/	\
 			 SCCR_EBDF00	|   SCCR_DFSYNC00 |	\
 			 SCCR_DFBRG00	|   SCCR_DFNL000  |	\
 			 SCCR_DFNH000)

 /*-----------------------------------------------------------------------
  * RTCSC - Real-Time Clock Status and Control Register		11-27
  *-----------------------------------------------------------------------
  */
 /* +0x0220 => 0x00C3 */
 #define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)


 /*-----------------------------------------------------------------------
  * RCCR - RISC Controller Configuration Register		19-4
  *-----------------------------------------------------------------------
  */
 /* +0x09C4 => TIMEP=1 */
 #define CONFIG_SYS_RCCR 0x0100

 /*-----------------------------------------------------------------------
  * RMDS - RISC Microcode Development Support Control Register
  *-----------------------------------------------------------------------
  */
 #define CONFIG_SYS_RMDS 0

 /*-----------------------------------------------------------------------
  * DER - Debug Event Register
  *-----------------------------------------------------------------------
  *
  */
 #define CONFIG_SYS_DER	0

 /*
  * Init Memory Controller:
  */

 /*
  * MAMR settings for SDRAM	- 16-14
  * => 0xC3804114
  */

 /* periodic timer for refresh */
 #define CONFIG_SYS_MAMR_PTA	0xC3

 #define CONFIG_SYS_MAMR	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 /*
  * BR1 and OR1 (FLASH)
  */
 #define FLASH_BASE		0x10000000	/* FLASH bank #0	*/

 /* used to re-map FLASH
  * restrict access enough to keep SRAM working (if any)
  * but not too much to meddle with FLASH accesses
  */
 /* allow for max 8 MB of Flash */
 #define CONFIG_SYS_REMAP_OR_AM		0xFF800000	/* OR addr mask */
 #define CONFIG_SYS_PRELIM_OR_AM	0xFF800000	/* OR addr mask */

 #define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK)

 #define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 #define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 /* 16 bit, bank valid */
 #define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )

 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
 #define CONFIG_SYS_BR1_PRELIM	CONFIG_SYS_BR0_PRELIM

 /*
  * BR2/OR2 - SDRAM
  */
 #define SDRAM_BASE		0x00000000	/* SDRAM bank */
 #define SDRAM_PRELIM_OR_AM	0xF8000000	/* map max. 128 MB */
 #define SDRAM_TIMING		0x00000A00	/* SDRAM-Timing */

 #define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB SDRAM */

 #define CONFIG_SYS_OR2		(SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
 #define CONFIG_SYS_BR2		((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V )

 /*
  * BR3/OR3 - SRAM (16 bit)
  */
 #define	SRAM_BASE	0x20000000
 #define CONFIG_SYS_OR3		0xFFF00130		/* BI/SCY = 5/TRLX (internal) */
 #define CONFIG_SYS_BR3		((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
 #define SRAM_SIZE	(1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK)))
 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR3			/* Make sure to map early */
 #define CONFIG_SYS_BR3_PRELIM	CONFIG_SYS_BR3			/* in case it's used for ENV */
 #define	CONFIG_SYS_SRAM_BASE	SRAM_BASE
 #define	CONFIG_SYS_SRAM_SIZE	SRAM_SIZE

 /*
  * BR4/OR4 - Board Control & Status (8 bit)
  */
 #define	BCSR_BASE	0xFC000000
 #define CONFIG_SYS_OR4		0xFFFF0120		/* BI (internal) */
 #define CONFIG_SYS_BR4		((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)

 /*
  * BR5/OR5 - IP Slot A/B (16 bit)
  */
 #define	IP_SLOT_BASE	0x40000000
 #define CONFIG_SYS_OR5		0xFE00010C		/* SETA/TRLX/BI/ SCY=0 (external) */
 #define CONFIG_SYS_BR5		((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)

 /*
  * BR6/OR6 - VME STD  (16 bit)
  */
 #define	VME_STD_BASE	0xFE000000
 #define CONFIG_SYS_OR6		0xFF00010C		/* SETA/TRLX/BI/SCY=0  (external) */
 #define CONFIG_SYS_BR6		((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)

 /*
  * BR7/OR7 - SHORT I/O + RTC + IACK  (16 bit)
  */
 #define VME_SHORT_BASE	0xFF000000
 #define CONFIG_SYS_OR7		0xFF00010C		/* SETA/TRLX/BI/ SCY=0 (external) */
 #define CONFIG_SYS_BR7		((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)

 /*-----------------------------------------------------------------------
  * Board Control and Status Region:
  *-----------------------------------------------------------------------
  */
 #ifndef __ASSEMBLY__
 typedef	struct ip860_bcsr_s {
 	unsigned char	shmem_addr;	/* +00 shared memory address register	*/
 	unsigned char	reserved0;
 	unsigned char	mbox_addr;	/* +02 mailbox address register		*/
 	unsigned char	reserved1;
 	unsigned char	vme_int_mask;	/* +04 VME Bus interrupt mask register	*/
 	unsigned char	reserved2;
 	unsigned char	vme_int_pend;	/* +06 VME interrupt pending register	*/
 	unsigned char	reserved3;
 	unsigned char	bd_int_mask;	/* +08 board interrupt mask register	*/
 	unsigned char	reserved4;
 	unsigned char	bd_int_pend;	/* +0A board interrupt pending register	*/
 	unsigned char	reserved5;
 	unsigned char	bd_ctrl;	/* +0C board control register		*/
 	unsigned char	reserved6;
 	unsigned char	bd_status;	/* +0E board status  register		*/
 	unsigned char	reserved7;
 	unsigned char	vme_irq;	/* +10 VME interrupt request register	*/
 	unsigned char	reserved8;
 	unsigned char	vme_ivec;	/* +12 VME interrupt vector register	*/
 	unsigned char	reserved9;
 	unsigned char	cli_mbox;	/* +14 clear mailbox irq		*/
 	unsigned char	reservedA;
 	unsigned char	rtc;		/* +16 RTC control register		*/
 	unsigned char	reservedB;
 	unsigned char	mbox_data;	/* +18 mailbox read/write register	*/
 	unsigned char	reservedC;
 	unsigned char	wd_trigger;	/* +1A Watchdog trigger register	*/
 	unsigned char	reservedD;
 	unsigned char	rmw_req;	/* +1C RMW request register		*/
 	unsigned char	reservedE;
 	unsigned char	bd_rev;		/* +1E Board Revision register		*/
 } ip860_bcsr_t;
 #endif	/* __ASSEMBLY__ */

 /*-----------------------------------------------------------------------
  * Board Control Register: bd_ctrl (Offset 0x0C)
  *-----------------------------------------------------------------------
  */
 #define BD_CTRL_IPLSE	0x80	/* IP Slot Long Select Enable		*/
 #define BD_CTRL_WDOGE	0x40	/* Watchdog Enable			*/
 #define BD_CTRL_FLWE	0x20	/* Flash Write Enable			*/
 #define BD_CTRL_RWDN	0x10	/* VMEBus Requester Release When Done Enable */

 /*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------
  *
  */

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2000-2005
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
	#define CONFIG_IP860 1 /* ...on a IP860 board */
	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */

	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	#define CONFIG_BAUDRATE 9600
	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \
	"\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0"

	#undef CONFIG_BOOTARGS
	#define CONFIG_BOOTCOMMAND \
	"bootp; " \
	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
	"bootm"

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */

	#undef CONFIG_WATCHDOG /* watchdog disabled */


	/* enable I2C and select the hardware/software driver */
	#undef CONFIG_HARD_I2C /* I2C with hardware support */
	#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
	/*
	* Software (bit-bang) I2C driver configuration
	*/
	#define PB_SCL 0x00000020 /* PB 26 */
	#define PB_SDA 0x00000010 /* PB 27 */

	#define I2C_INIT (immr->im_cpm.cp_pbdir \|= PB_SCL)
	#define I2C_ACTIVE (immr->im_cpm.cp_pbdir \|= PB_SDA)
	#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
	#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
	#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat \|= PB_SDA; \
	else immr->im_cpm.cp_pbdat &= ~PB_SDA
	#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat \|= PB_SCL; \
	else immr->im_cpm.cp_pbdat &= ~PB_SCL
	#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */


	# define CONFIG_SYS_I2C_SPEED 50000
	# define CONFIG_SYS_I2C_SLAVE 0xFE
	# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
	# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
	/* mask of address bits that overflow into the "EEPROM chip address" */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */

	#define CONFIG_TIMESTAMP /* Print image info with timestamp */


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_BEDBUG
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_SNTP

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME
	#define CONFIG_BOOTP_BOOTPATH

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */

	#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/
	/*-----------------------------------------------------------------------
	* Internal Memory Mapped Register
	*/
	#define CONFIG_SYS_IMMR 0xF1000000 /* Non-standard value!! */

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_FLASH_BASE 0x10000000
	#ifdef DEBUG
	#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
	#else
	#if 0 /* need more space for I2C tests */
	#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
	#else
	#define CONFIG_SYS_MONITOR_LEN (256 << 10)
	#endif
	#endif
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 124 /* max number of sectors on one chip */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	#undef CONFIG_ENV_IS_IN_FLASH
	#undef CONFIG_ENV_IS_IN_NVRAM
	#undef CONFIG_ENV_IS_IN_NVRAM
	#undef DEBUG_I2C
	#define CONFIG_ENV_IS_IN_EEPROM

	#ifdef CONFIG_ENV_IS_IN_NVRAM
	#define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */
	#define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */
	#endif /* CONFIG_ENV_IS_IN_NVRAM */

	#ifdef CONFIG_ENV_IS_IN_EEPROM
	#define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */
	#define CONFIG_ENV_SIZE 1536 /* Use remaining space */
	#endif /* CONFIG_ENV_IS_IN_EEPROM */

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
	#endif
	#define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before
	* running in RAM.
	*/

	/*-----------------------------------------------------------------------
	* SYPCR - System Protection Control 11-9
	* SYPCR can only be written once after reset!
	*-----------------------------------------------------------------------
	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	* +0x0004
	*/
	#if defined(CONFIG_WATCHDOG)
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
	#else
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| SYPCR_SWP)
	#endif

	/*-----------------------------------------------------------------------
	* SIUMCR - SIU Module Configuration 11-6
	*-----------------------------------------------------------------------
	* +0x0000 => 0x80600800
	*/
	#define CONFIG_SYS_SIUMCR (SIUMCR_EARB \| SIUMCR_EARP0 \| \
	SIUMCR_DBGC11 \| SIUMCR_MLRC10)

	/*-----------------------------------------------------------------------
	* Clock Setting - get clock frequency from Board Revision Register
	*-----------------------------------------------------------------------
	*/
	#ifndef __ASSEMBLY__
	extern unsigned long ip860_get_clk_freq (void);
	#endif
	#define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq()

	/*-----------------------------------------------------------------------
	* TBSCR - Time Base Status and Control 11-26
	*-----------------------------------------------------------------------
	* Clear Reference Interrupt Status, Timebase freezing enabled
	* +0x0200 => 0x00C2
	*/
	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)

	/*-----------------------------------------------------------------------
	* PISCR - Periodic Interrupt Status and Control 11-31
	*-----------------------------------------------------------------------
	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	* +0x0240 => 0x0082
	*/
	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF)

	/*-----------------------------------------------------------------------
	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	*-----------------------------------------------------------------------
	* Reset PLL lock status sticky bit, timer expired status bit and timer
	* interrupt status bit, set PLL multiplication factor !
	*/
	/* +0x0286 => was: 0x0000D000 */
	#define CONFIG_SYS_PLPRCR \
	( PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST \| \
	/PLPRCR_CSRC\|/ PLPRCR_LPM_NORMAL \| \
	PLPRCR_CSR \| PLPRCR_LOLRE /\|PLPRCR_FIOPD/ \
	)

	/*-----------------------------------------------------------------------
	* SCCR - System Clock and reset Control Register 15-27
	*-----------------------------------------------------------------------
	* Set clock output, timebase and RTC source and divider,
	* power management and some other internal clocks
	*/
	#define SCCR_MASK SCCR_EBDF11
	#define CONFIG_SYS_SCCR (SCCR_COM00 \| SCCR_TBS \| \
	SCCR_RTDIV \| SCCR_RTSEL \| \
	/SCCR_CRQEN\|/ /SCCR_PRQEN\|/ \
	SCCR_EBDF00 \| SCCR_DFSYNC00 \| \
	SCCR_DFBRG00 \| SCCR_DFNL000 \| \
	SCCR_DFNH000)

	/*-----------------------------------------------------------------------
	* RTCSC - Real-Time Clock Status and Control Register 11-27
	*-----------------------------------------------------------------------
	*/
	/* +0x0220 => 0x00C3 */
	#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE)


	/*-----------------------------------------------------------------------
	* RCCR - RISC Controller Configuration Register 19-4
	*-----------------------------------------------------------------------
	*/
	/* +0x09C4 => TIMEP=1 */
	#define CONFIG_SYS_RCCR 0x0100

	/*-----------------------------------------------------------------------
	* RMDS - RISC Microcode Development Support Control Register
	*-----------------------------------------------------------------------
	*/
	#define CONFIG_SYS_RMDS 0

	/*-----------------------------------------------------------------------
	* DER - Debug Event Register
	*-----------------------------------------------------------------------
	*
	*/
	#define CONFIG_SYS_DER 0

	/*
	* Init Memory Controller:
	*/

	/*
	* MAMR settings for SDRAM - 16-14
	* => 0xC3804114
	*/

	/* periodic timer for refresh */
	#define CONFIG_SYS_MAMR_PTA 0xC3

	#define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	/*
	* BR1 and OR1 (FLASH)
	*/
	#define FLASH_BASE 0x10000000 /* FLASH bank #0 */

	/* used to re-map FLASH
	* restrict access enough to keep SRAM working (if any)
	* but not too much to meddle with FLASH accesses
	*/
	/* allow for max 8 MB of Flash */
	#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */
	#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */

	#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM \| OR_ACS_DIV2 \| OR_BI \| OR_SCY_6_CLK)

	#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	/* 16 bit, bank valid */
	#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) \| BR_PS_32 \| BR_V )

	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_BR0_PRELIM

	/*
	* BR2/OR2 - SDRAM
	*/
	#define SDRAM_BASE 0x00000000 /* SDRAM bank */
	#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
	#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */

	#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */

	#define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM \| SDRAM_TIMING )
	#define CONFIG_SYS_BR2 ((SDRAM_BASE & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )

	/*
	* BR3/OR3 - SRAM (16 bit)
	*/
	#define SRAM_BASE 0x20000000
	#define CONFIG_SYS_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */
	#define CONFIG_SYS_BR3 ((SRAM_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
	#define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK)))
	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */
	#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */
	#define CONFIG_SYS_SRAM_BASE SRAM_BASE
	#define CONFIG_SYS_SRAM_SIZE SRAM_SIZE

	/*
	* BR4/OR4 - Board Control & Status (8 bit)
	*/
	#define BCSR_BASE 0xFC000000
	#define CONFIG_SYS_OR4 0xFFFF0120 /* BI (internal) */
	#define CONFIG_SYS_BR4 ((BCSR_BASE & BR_BA_MSK) \| BR_PS_8 \| BR_V)

	/*
	* BR5/OR5 - IP Slot A/B (16 bit)
	*/
	#define IP_SLOT_BASE 0x40000000
	#define CONFIG_SYS_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */
	#define CONFIG_SYS_BR5 ((IP_SLOT_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)

	/*
	* BR6/OR6 - VME STD (16 bit)
	*/
	#define VME_STD_BASE 0xFE000000
	#define CONFIG_SYS_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */
	#define CONFIG_SYS_BR6 ((VME_STD_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)

	/*
	* BR7/OR7 - SHORT I/O + RTC + IACK (16 bit)
	*/
	#define VME_SHORT_BASE 0xFF000000
	#define CONFIG_SYS_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */
	#define CONFIG_SYS_BR7 ((VME_SHORT_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)

	/*-----------------------------------------------------------------------
	* Board Control and Status Region:
	*-----------------------------------------------------------------------
	*/
	#ifndef __ASSEMBLY__
	typedef struct ip860_bcsr_s {
	unsigned char shmem_addr; /* +00 shared memory address register */
	unsigned char reserved0;
	unsigned char mbox_addr; /* +02 mailbox address register */
	unsigned char reserved1;
	unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */
	unsigned char reserved2;
	unsigned char vme_int_pend; /* +06 VME interrupt pending register */
	unsigned char reserved3;
	unsigned char bd_int_mask; /* +08 board interrupt mask register */
	unsigned char reserved4;
	unsigned char bd_int_pend; /* +0A board interrupt pending register */
	unsigned char reserved5;
	unsigned char bd_ctrl; /* +0C board control register */
	unsigned char reserved6;
	unsigned char bd_status; /* +0E board status register */
	unsigned char reserved7;
	unsigned char vme_irq; /* +10 VME interrupt request register */
	unsigned char reserved8;
	unsigned char vme_ivec; /* +12 VME interrupt vector register */
	unsigned char reserved9;
	unsigned char cli_mbox; /* +14 clear mailbox irq */
	unsigned char reservedA;
	unsigned char rtc; /* +16 RTC control register */
	unsigned char reservedB;
	unsigned char mbox_data; /* +18 mailbox read/write register */
	unsigned char reservedC;
	unsigned char wd_trigger; /* +1A Watchdog trigger register */
	unsigned char reservedD;
	unsigned char rmw_req; /* +1C RMW request register */
	unsigned char reservedE;
	unsigned char bd_rev; /* +1E Board Revision register */
	} ip860_bcsr_t;
	#endif /* __ASSEMBLY__ */

	/*-----------------------------------------------------------------------
	* Board Control Register: bd_ctrl (Offset 0x0C)
	*-----------------------------------------------------------------------
	*/
	#define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */
	#define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */
	#define BD_CTRL_FLWE 0x20 /* Flash Write Enable */
	#define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */

	/*-----------------------------------------------------------------------
	*
	*-----------------------------------------------------------------------
	*
	*/

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#endif /* __CONFIG_H */