| #include <ppc_asm.tmpl> |
| #include <mpc824x.h> |
| #include <ppc_defs.h> |
| #include <asm/cache.h> |
| #include <asm/mmu.h> |
| |
| #define USE_V2_INIT 1 /* Jimmy Blair's initialization. */ |
| |
| |
| /* |
| * Initialize the MMU using BAT entries and hardwired TLB |
| * This obviates the need for any code in cpu_init_f which |
| * configures the BAT registers. |
| */ |
| #define MEMORY_MGMT_MSR_BITS (MSR_DR | MSR_IR) /* Data and Inst Relocate */ |
| .global iommu_setup |
| /* Initialize IO/MMU mappings via BAT method Ch. 7, |
| * PPC Programming Reference |
| */ |
| iommu_setup: |
| |
| /* initialize the BAT registers (SPRs 528 - 543 */ |
| #define mtibat0u(x) mtspr 528,(x) /* SPR 528 (IBAT0U) */ |
| #define mtibat0l(x) mtspr 529,(x) /* SPR 529 (IBAT0L) */ |
| #define mtibat1u(x) mtspr 530,(x) /* SPR 530 (IBAT1U) */ |
| #define mtibat1l(x) mtspr 531,(x) /* SPR 531 (IBAT1L) */ |
| #define mtibat2u(x) mtspr 532,(x) /* SPR 532 (IBAT2U) */ |
| #define mtibat2l(x) mtspr 533,(x) /* SPR 533 (IBAT2L) */ |
| #define mtibat3u(x) mtspr 534,(x) /* SPR 534 (IBAT3U) */ |
| #define mtibat3l(x) mtspr 535,(x) /* SPR 535 (IBAT3L) */ |
| #define mtdbat0u(x) mtspr 536,(x) /* SPR 536 (DBAT0U) */ |
| #define mtdbat0l(x) mtspr 537,(x) /* SPR 537 (DBAT0L) */ |
| #define mtdbat1u(x) mtspr 538,(x) /* SPR 538 (DBAT1U) */ |
| #define mtdbat1l(x) mtspr 539,(x) /* SPR 539 (DBAT1L) */ |
| #define mtdbat2u(x) mtspr 540,(x) /* SPR 540 (DBAT2U) */ |
| #define mtdbat2l(x) mtspr 541,(x) /* SPR 541 (DBAT2L) */ |
| #define mtdbat3u(x) mtspr 542,(x) /* SPR 542 (DBAT3U) */ |
| #define mtdbat3l(x) mtspr 543,(x) /* SPR 543 (DBAT3L) */ |
| |
| |
| /* PowerPC processors do not necessarily initialize the BAT |
| registers on power-up or reset. So they are in an unknown |
| state. Before programming the BATs for the first time, all |
| BAT registers MUST have their Vs and Vp bits cleared in the |
| upper BAT half in order to avoid possibly having 2 BATs |
| valid and mapping the same memory region. |
| |
| The reason for this is that, even with address translation |
| disabled, multiple BAT hits for an address are treated as |
| programming errors and can cause unpredictable results. |
| |
| It is up to the software to make sure it never has 2 IBAT |
| mappings or 2 DBAT mappings that are valid for the same |
| addresses. It is not necessary to perform this code |
| sequence every time the BATs are programmed, only when |
| there is a possibility that there may be overlapping BAT |
| entries. |
| |
| When programming the BATs in non-reset scenarios, even if |
| you are sure that your new mapping will not temporarily |
| create overlapping regions, it is still a wise idea to |
| invalidate a BAT entry by setting its upper BAT register to |
| all 0's before programming it. This will avoid having a |
| BAT marked valid that is in an unknown or transient state |
| */ |
| |
| addis r5,0,0x0000 |
| mtibat0u(r5) |
| mtibat0l(r5) |
| mtibat1u(r5) |
| mtibat1l(r5) |
| mtibat2u(r5) |
| mtibat2l(r5) |
| mtibat3u(r5) |
| mtibat3l(r5) |
| mtdbat0u(r5) |
| mtdbat0l(r5) |
| mtdbat1u(r5) |
| mtdbat1l(r5) |
| mtdbat2u(r5) |
| mtdbat2l(r5) |
| mtdbat3u(r5) |
| mtdbat3l(r5) |
| isync |
| |
| /* |
| * Set up I/D BAT0 |
| */ |
| lis r4, CFG_DBAT0L@h |
| ori r4, r4, CFG_DBAT0L@l |
| lis r3, CFG_DBAT0U@h |
| ori r3, r3, CFG_DBAT0U@l |
| |
| mtdbat0l(r4) |
| isync |
| mtdbat0u(r3) |
| isync |
| sync |
| |
| lis r4, CFG_IBAT0L@h |
| ori r4, r4, CFG_IBAT0L@l |
| lis r3, CFG_IBAT0U@h |
| ori r3, r3, CFG_IBAT0U@l |
| |
| isync |
| mtibat0l(r4) |
| isync |
| mtibat0u(r3) |
| isync |
| |
| /* |
| * Set up I/D BAT1 |
| */ |
| lis r4, CFG_IBAT1L@h |
| ori r4, r4, CFG_IBAT1L@l |
| lis r3, CFG_IBAT1U@h |
| ori r3, r3, CFG_IBAT1U@l |
| |
| isync |
| mtibat1l(r4) |
| isync |
| mtibat1u(r3) |
| isync |
| mtdbat1l(r4) |
| isync |
| mtdbat1u(r3) |
| isync |
| sync |
| |
| /* |
| * Set up I/D BAT2 |
| */ |
| lis r4, CFG_IBAT2L@h |
| ori r4, r4, CFG_IBAT2L@l |
| lis r3, CFG_IBAT2U@h |
| ori r3, r3, CFG_IBAT2U@l |
| |
| isync |
| mtibat2l(r4) |
| isync |
| mtibat2u(r3) |
| isync |
| mtdbat2l(r4) |
| isync |
| mtdbat2u(r3) |
| isync |
| sync |
| |
| /* |
| * Setup I/D BAT3 |
| */ |
| lis r4, CFG_IBAT3L@h |
| ori r4, r4, CFG_IBAT3L@l |
| lis r3, CFG_IBAT3U@h |
| ori r3, r3, CFG_IBAT3U@l |
| |
| isync |
| mtibat3l(r4) |
| isync |
| mtibat3u(r3) |
| isync |
| mtdbat3l(r4) |
| isync |
| mtdbat3u(r3) |
| isync |
| sync |
| |
| |
| /* |
| * Invalidate all 64 TLB's |
| */ |
| lis r3, 0 |
| mtctr r3 |
| lis r5, 4 |
| |
| tlblp: |
| tlbie r3 |
| sync |
| addi r3, r3, 0x1000 |
| cmplw r3, r5 |
| blt tlblp |
| |
| sync |
| |
| /* |
| * Enable Data Translation |
| */ |
| lis r4, MEMORY_MGMT_MSR_BITS@h |
| ori r4, r4, MEMORY_MGMT_MSR_BITS@l |
| mfmsr r3 |
| or r3, r4, r3 |
| mtmsr r3 |
| isync |
| sync |
| |
| blr |
| |
| |
| #ifdef USE_V2_INIT |
| /* #define USER_I_CACHE_ENABLE 1*/ /* Fast rom boots */ |
| /* Macro for hiadjust and lo */ |
| #define HIADJ(arg) arg@ha |
| #define HI(arg) arg@h |
| #define LO(arg) arg@l |
| |
| #undef LOADPTR |
| #define LOADPTR(reg,const32) \ |
| addis reg,r0,HIADJ(const32); addi reg,reg,LO(const32) |
| |
| .globl early_init_f |
| |
| early_init_f: |
| /* MPC8245/BMW CPCI System Init |
| * Jimmy Blair, Broadcom Corp, 2002. |
| */ |
| mflr r11 |
| /* Zero-out registers */ |
| |
| addis r0,r0,0 |
| mtspr SPRG0,r0 |
| mtspr SPRG1,r0 |
| mtspr SPRG2,r0 |
| mtspr SPRG3,r0 |
| |
| /* Set MPU/MSR to a known state. Turn on FP */ |
| |
| LOADPTR (r3, MSR_FP) |
| sync |
| mtmsr r3 |
| isync |
| |
| /* Init the floating point control/status register */ |
| |
| mtfsfi 7,0x0 |
| mtfsfi 6,0x0 |
| mtfsfi 5,0x0 |
| mtfsfi 4,0x0 |
| mtfsfi 3,0x0 |
| mtfsfi 2,0x0 |
| mtfsfi 1,0x0 |
| mtfsfi 0,0x0 |
| isync |
| |
| /* Set MPU/MSR to a known state. Turn off FP */ |
| |
| #if 1 /* Turn off floating point (remove to keep FP on) */ |
| andi. r3, r3, 0 |
| sync |
| mtmsr r3 |
| isync |
| #endif |
| |
| /* Init the Segment registers */ |
| |
| andi. r3, r3, 0 |
| isync |
| mtsr 0,r3 |
| isync |
| mtsr 1,r3 |
| isync |
| mtsr 2,r3 |
| isync |
| mtsr 3,r3 |
| isync |
| mtsr 4,r3 |
| isync |
| mtsr 5,r3 |
| isync |
| mtsr 6,r3 |
| isync |
| mtsr 7,r3 |
| isync |
| mtsr 8,r3 |
| isync |
| mtsr 9,r3 |
| isync |
| mtsr 10,r3 |
| isync |
| mtsr 11,r3 |
| isync |
| mtsr 12,r3 |
| isync |
| mtsr 13,r3 |
| isync |
| mtsr 14,r3 |
| isync |
| mtsr 15,r3 |
| isync |
| |
| /* Turn off data and instruction cache control bits */ |
| |
| mfspr r3, HID0 |
| isync |
| rlwinm r4, r3, 0, 18, 15 /* r4 has ICE and DCE bits cleared */ |
| sync |
| isync |
| mtspr HID0, r4 /* HID0 = r4 */ |
| isync |
| |
| /* Get cpu type */ |
| |
| mfspr r28, PVR |
| rlwinm r28, r28, 16, 16, 31 |
| |
| /* invalidate the MPU's data/instruction caches */ |
| |
| lis r3, 0x0 |
| cmpli 0, 0, r28, CPU_TYPE_603 |
| beq cpuIs603 |
| cmpli 0, 0, r28, CPU_TYPE_603E |
| beq cpuIs603 |
| cmpli 0, 0, r28, CPU_TYPE_603P |
| beq cpuIs603 |
| cmpli 0, 0, r28, CPU_TYPE_604R |
| bne cpuNot604R |
| |
| cpuIs604R: |
| lis r3, 0x0 |
| mtspr HID0, r3 /* disable the caches */ |
| isync |
| ori r4, r4, 0x0002 /* disable BTAC by setting bit 30 */ |
| |
| cpuNot604R: |
| ori r3, r3, (HID0_ICFI |HID0_DCI) |
| |
| cpuIs603: |
| ori r3, r3, (HID0_ICE | HID0_DCE) |
| or r4, r4, r3 /* set bits */ |
| sync |
| isync |
| mtspr HID0, r4 /* HID0 = r4 */ |
| andc r4, r4, r3 /* clear bits */ |
| isync |
| cmpli 0, 0, r28, CPU_TYPE_604 |
| beq cpuIs604 |
| cmpli 0, 0, r28, CPU_TYPE_604E |
| beq cpuIs604 |
| cmpli 0, 0, r28, CPU_TYPE_604R |
| beq cpuIs604 |
| mtspr HID0, r4 |
| isync |
| |
| #ifdef USER_I_CACHE_ENABLE |
| b instCacheOn603 |
| #else |
| b cacheEnableDone |
| #endif |
| |
| cpuIs604: |
| LOADPTR (r5, 0x1000) /* loop count, 0x1000 */ |
| mtspr CTR, r5 |
| loopDelay: |
| nop |
| bdnz loopDelay |
| isync |
| mtspr HID0, r4 |
| isync |
| |
| /* turn the Instruction cache ON for faster FLASH ROM boots */ |
| |
| #ifdef USER_I_CACHE_ENABLE |
| |
| ori r4, r4, (HID0_ICE | HID0_ICFI) |
| isync /* Synchronize for ICE enable */ |
| b writeReg4 |
| instCacheOn603: |
| ori r4, r4, (HID0_ICE | HID0_ICFI) |
| rlwinm r3, r4, 0, 21, 19 /* clear the ICFI bit */ |
| |
| /* |
| * The setting of the instruction cache enable (ICE) bit must be |
| * preceded by an isync instruction to prevent the cache from being |
| * enabled or disabled while an instruction access is in progress. |
| */ |
| isync |
| writeReg4: |
| mtspr HID0, r4 /* Enable Instr Cache & Inval cache */ |
| cmpli 0, 0, r28, CPU_TYPE_604 |
| beq cacheEnableDone |
| cmpli 0, 0, r28, CPU_TYPE_604E |
| beq cacheEnableDone |
| |
| mtspr HID0, r3 /* using 2 consec instructions */ |
| /* PPC603 recommendation */ |
| #endif |
| cacheEnableDone: |
| |
| /* Detect map A or B */ |
| |
| addis r5,r0, HI(CHRP_REG_ADDR) |
| addis r6,r0, HI(CHRP_REG_DATA) |
| LOADPTR (r7, KAHLUA_ID) /* Kahlua PCI controller ID */ |
| LOADPTR (r8, BMC_BASE) |
| |
| stwbrx r8,0,(r5) |
| lwbrx r3,0,(r6) /* Store read value to r3 */ |
| cmp 0,0,r3,r7 |
| beq cr0, X4_KAHLUA_START |
| |
| /* It's not an 8240, is it an 8245? */ |
| |
| LOADPTR (r7, KAHLUA2_ID) /* Kahlua PCI controller ID */ |
| cmp 0,0,r3,r7 |
| beq cr0, X4_KAHLUA_START |
| |
| /* Save the PCI controller type in r7 */ |
| mr r7, r3 |
| |
| LOADPTR (r5, PREP_REG_ADDR) |
| LOADPTR (r6, PREP_REG_DATA) |
| |
| X4_KAHLUA_START: |
| /* MPC8245 changes begin here */ |
| LOADPTR (r3, MPC107_PCI_CMD) /* PCI command reg */ |
| stwbrx r3,0,r5 |
| li r4, 6 /* Command register value */ |
| sthbrx r4, 0, r6 |
| |
| LOADPTR (r3, MPC107_PCI_STAT) /* PCI status reg */ |
| stwbrx r3,0,r5 |
| li r4, -1 /* Write-to-clear all bits */ |
| li r3, 2 /* PCI_STATUS is at +2 offset */ |
| sthbrx r4, r3, r6 |
| |
| /*-------PROC_INT1_ADR */ |
| |
| LOADPTR (r3, PROC_INT1_ADR) /* Processor I/F Config 1 reg. */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0xff141b98) |
| stwbrx r4,0,r6 |
| |
| /*-------PROC_INT2_ADR */ |
| |
| LOADPTR (r3, PROC_INT2_ADR) /* Processor I/F Config 2 reg. */ |
| stwbrx r3,0,r5 |
| lis r4, 0x2000 /* Flush PCI config writes */ |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r9, KAHLUA2_ID) |
| cmpl 0, 0, r7, r9 |
| bne L1not8245 |
| |
| /* MIOCR1 -- turn on bit for DLL delay */ |
| |
| LOADPTR (r3, MIOCR1_ADR_X) |
| stwbrx r3,0,r5 |
| li r4, 0x04 |
| stb r4, MIOCR1_SHIFT(r6) |
| |
| /* For the MPC8245, set register 77 to %00100000 (see Errata #15) */ |
| /* SDRAM_CLK_DEL (0x77)*/ |
| |
| LOADPTR (r3, MIOCR2_ADR_X) |
| stwbrx r3,0,r5 |
| li r4, 0x10 |
| stb r4, MIOCR2_SHIFT(r6) |
| |
| /* PMCR2 -- set PCI hold delay to <10>b for 33 MHz */ |
| |
| LOADPTR (r3, PMCR2_ADR_X) |
| stwbrx r3,0,r5 |
| li r4, 0x20 |
| stb r4, PMCR2_SHIFT(r6) |
| |
| /* Initialize EUMBBAR early since 8245 has internal UART in EUMB */ |
| |
| LOADPTR (r3, EUMBBAR) |
| stwbrx r3,0,r5 |
| LOADPTR (r4, CFG_EUMB_ADDR) |
| stwbrx r4,0,r6 |
| |
| L1not8245: |
| |
| /* Toggle the DLL reset bit in AMBOR */ |
| |
| LOADPTR (r3, AMBOR) |
| stwbrx r3,0,r5 |
| lbz r4, 0(r6) |
| |
| andi. r4, r4, 0xdf |
| stb r4, 0(r6) /* Clear DLL_RESET */ |
| sync |
| |
| ori r4, r4, 0x20 /* Set DLL_RESET */ |
| stb r4, 0(r6) |
| sync |
| |
| andi. r4, r4, 0xdf |
| stb r4, 0(r6) /* Clear DLL_RESET */ |
| |
| |
| /* Enable RCS2, use supplied timings */ |
| LOADPTR (r3, ERCR1) |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x80408000) |
| stwbrx r4,0,r6 |
| |
| /* Disable RCS3 parameters */ |
| LOADPTR (r3, ERCR2) |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x00000000) |
| stwbrx r4,0,r6 |
| |
| /* RCS3 at 0x70000000, 64KBytes */ |
| LOADPTR (r3, ERCR2) |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x00000004) |
| stwbrx r4,0,r6 |
| |
| /*-------MCCR1 */ |
| |
| #ifdef INCLUDE_ECC |
| #define MC_ECC 1 |
| #else /* INCLUDE_ECC */ |
| #define MC_ECC 0 |
| #endif /* INCLUDE_ECC */ |
| |
| #define MC1_ROMNAL 8 /* 0-15 */ |
| #define MC1_ROMFAL 11 /* 0-31 */ |
| #define MC1_DBUS_SIZE 0 /* 0-3, read only */ |
| #define MC1_BURST 0 /* 0-1 */ |
| #define MC1_MEMGO 0 /* 0-1 */ |
| #define MC1_SREN 1 /* 0-1 */ |
| #define MC1_RAM_TYPE 0 /* 0-1 */ |
| #define MC1_PCKEN MC_ECC /* 0-1 */ |
| #define MC1_BANKBITS 0x5555 /* 2 bits/bank 7-0 */ |
| |
| LOADPTR (r3, MEM_CONT1_ADR) /* Set MCCR1 (F0) */ |
| stwbrx r3,0,r5 |
| LOADPTR(r4, \ |
| MC1_ROMNAL << 28 | MC1_ROMFAL << 23 | \ |
| MC1_DBUS_SIZE << 21 | MC1_BURST << 20 | \ |
| MC1_MEMGO << 19 | MC1_SREN << 18 | \ |
| MC1_RAM_TYPE << 17 | MC1_PCKEN << 16 ) |
| li r3, MC1_BANKBITS |
| cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ |
| bne BankBitsAdd |
| cmpli 0, 0, r3, 0x5555 |
| beq K2BankBitsHack /* On 8245, 5555 ==> 0 */ |
| BankBitsAdd: |
| ori r4, r3, 0 |
| K2BankBitsHack: |
| stwbrx r4, 0, r6 |
| |
| /*------- MCCR2 */ |
| |
| #define MC2_TS_WAIT_TIMER 0 /* 0-7 */ |
| #define MC2_ASRISE 8 /* 0-15 */ |
| #define MC2_ASFALL 4 /* 0-15 */ |
| #define MC2_INLINE_PAR_NOT_ECC 0 /* 0-1 */ |
| #define MC2_WRITE_PARITY_CHK_EN MC_ECC /* 0-1 */ |
| #define MC2_INLRD_PARECC_CHK_EN MC_ECC /* 0-1 */ |
| #define MC2_ECC_EN 0 /* 0-1 */ |
| #define MC2_EDO 0 /* 0-1 */ |
| /* |
| * N.B. This refresh interval looks good up to 85 MHz with Hynix SDRAM. |
| * May need to be decreased for 100 MHz |
| */ |
| #define MC2_REFINT 0x3a5 /* 0-0x3fff */ |
| #define MC2_RSV_PG 0 /* 0-1 */ |
| #define MC2_RMW_PAR MC_ECC /* 0-1 */ |
| |
| LOADPTR (r3, MEM_CONT2_ADR) /* Set MCCR2 (F4) */ |
| stwbrx r3,0,r5 |
| LOADPTR(r4, \ |
| MC2_TS_WAIT_TIMER << 29 | MC2_ASRISE << 25 | \ |
| MC2_ASFALL << 21 | MC2_INLINE_PAR_NOT_ECC << 20 | \ |
| MC2_WRITE_PARITY_CHK_EN << 19 | \ |
| MC2_INLRD_PARECC_CHK_EN << 18 | \ |
| MC2_ECC_EN << 17 | MC2_EDO << 16 | \ |
| MC2_REFINT << 2 | MC2_RSV_PG << 1 | MC2_RMW_PAR) |
| cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ |
| bne notK2 |
| /* clear Kahlua2 reserved bits */ |
| LOADPTR (r3, 0xfffcffff) |
| and r4, r4, r3 |
| notK2: |
| stwbrx r4,0,r6 |
| |
| /*------- MCCR3 */ |
| |
| #define MC_BSTOPRE 0x079 /* 0-0x7ff */ |
| |
| #define MC3_BSTOPRE_U (MC_BSTOPRE >> 4 & 0xf) |
| #define MC3_REFREC 8 /* 0-15 */ |
| #define MC3_RDLAT (4+MC_ECC) /* 0-15 */ |
| #define MC3_CPX 0 /* 0-1 */ |
| #define MC3_RAS6P 0 /* 0-15 */ |
| #define MC3_CAS5 0 /* 0-7 */ |
| #define MC3_CP4 0 /* 0-7 */ |
| #define MC3_CAS3 0 /* 0-7 */ |
| #define MC3_RCD2 0 /* 0-7 */ |
| #define MC3_RP1 0 /* 0-7 */ |
| |
| LOADPTR (r3, MEM_CONT3_ADR) /* Set MCCR3 (F8) */ |
| stwbrx r3,0,r5 |
| LOADPTR(r4, \ |
| MC3_BSTOPRE_U << 28 | MC3_REFREC << 24 | \ |
| MC3_RDLAT << 20 | MC3_CPX << 19 | \ |
| MC3_RAS6P << 15 | MC3_CAS5 << 12 | MC3_CP4 << 9 | \ |
| MC3_CAS3 << 6 | MC3_RCD2 << 3 | MC3_RP1) |
| cmpl 0, 0, r7, r9 /* Check for Kahlua2 */ |
| bne notK2b |
| /* clear Kahlua2 reserved bits */ |
| LOADPTR (r3, 0xff000000) |
| and r4, r4, r3 |
| notK2b: |
| stwbrx r4,0,r6 |
| |
| /*------- MCCR4 */ |
| |
| #define MC4_PRETOACT 3 /* 0-15 */ |
| #define MC4_ACTOPRE 5 /* 0-15 */ |
| #define MC4_WMODE 0 /* 0-1 */ |
| #define MC4_INLINE MC_ECC /* 0-1 */ |
| #define MC4_REGISTERED (1-MC_ECC) /* 0-1 */ |
| #define MC4_BSTOPRE_UU (MC_BSTOPRE >> 8 & 3) |
| #define MC4_REGDIMM 0 /* 0-1 */ |
| #define MC4_SDMODE_CAS 2 /* 0-7 */ |
| #define MC4_DBUS_RCS1 1 /* 0-1, 8-bit */ |
| #define MC4_SDMODE_WRAP 0 /* 0-1 */ |
| #define MC4_SDMODE_BURST 2 /* 0-7 */ |
| #define MC4_ACTORW 3 /* 0-15 */ |
| #define MC4_BSTOPRE_L (MC_BSTOPRE & 0xf) |
| |
| LOADPTR (r3, MEM_CONT4_ADR) /* Set MCCR4 (FC) */ |
| stwbrx r3,0,r5 |
| LOADPTR(r4, \ |
| MC4_PRETOACT << 28 | MC4_ACTOPRE << 24 | \ |
| MC4_WMODE << 23 | MC4_INLINE << 22 | \ |
| MC4_REGISTERED << 20 | MC4_BSTOPRE_UU << 18 | \ |
| MC4_DBUS_RCS1 << 17 | \ |
| MC4_REGDIMM << 15 | MC4_SDMODE_CAS << 12 | \ |
| MC4_SDMODE_WRAP << 11 | MC4_SDMODE_BURST << 8 | \ |
| MC4_ACTORW << 4 | MC4_BSTOPRE_L) |
| cmpl 0, 0, r7, r9 /* Check for Kahlua 2 */ |
| bne notK2c |
| /* Turn on Kahlua2 extended ROM space */ |
| LOADPTR (r3, 0x00200000) |
| or r4, r4, r3 |
| notK2c: |
| stwbrx r4,0,r6 |
| |
| #ifdef INCLUDE_ECC |
| /*------- MEM_ERREN1 */ |
| |
| LOADPTR (r3, MEM_ERREN1_ADR) /* Set MEM_ERREN1 (c0) */ |
| stwbrx r3,0,r5 |
| lwbrx r4,0,r6 |
| ori r4,r4,4 /* Set MEM_PERR_EN */ |
| stwbrx r4,0,r6 |
| #endif /* INCLUDE_ECC */ |
| |
| /*------- MSAR/MEAR */ |
| |
| LOADPTR (r3, MEM_START1_ADR) /* Set MSAR1 (80) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0xc0804000) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, MEM_START2_ADR) /* Set MSAR2 (84) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0xc0804000) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, XMEM_START1_ADR) /* Set MESAR1 (88) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x00000000) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, XMEM_START2_ADR) /* Set MESAR2 (8c) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x01010101) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, MEM_END1_ADR) /* Set MEAR1 (90) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0xffbf7f3f) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, MEM_END2_ADR) /* Set MEAR2 (94) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0xffbf7f3f) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, XMEM_END1_ADR) /* MEEAR1 (98) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x00000000) |
| stwbrx r4,0,r6 |
| |
| LOADPTR (r3, XMEM_END2_ADR) /* MEEAR2 (9c) */ |
| stwbrx r3,0,r5 |
| LOADPTR (r4, 0x01010101) |
| stwbrx r4,0,r6 |
| |
| /*-------ODCR */ |
| |
| LOADPTR (r3, ODCR_ADR_X) /* Set ODCR */ |
| stwbrx r3,0,r5 |
| |
| li r4, 0x7f |
| stb r4, ODCR_SHIFT(r6) /* ODCR is at +3 offset */ |
| |
| /*-------MBEN */ |
| |
| LOADPTR (r3, MEM_EN_ADR) /* Set MBEN (a0) */ |
| stwbrx r3,0,r5 |
| li r4, 0x01 /* Enable bank 0 */ |
| stb r4, 0(r6) /* MBEN is at +0 offset */ |
| |
| #if 0 /* Jimmy: I think page made is broken */ |
| /*-------PGMAX */ |
| |
| LOADPTR (r3, MPM_ADR_X) |
| stwbrx r3,0,r5 |
| li r4, 0x32 |
| stb r4, MPM_SHIFT(r6) /* PAGE_MODE is at +3 offset */ |
| #endif |
| |
| /* Wait before initializing other registers */ |
| |
| lis r4,0x0001 |
| mtctr r4 |
| |
| KahluaX4wait200us: |
| bdnz KahluaX4wait200us |
| |
| /* Set MEMGO bit */ |
| |
| LOADPTR (r3, MEM_CONT1_ADR) /* MCCR1 (F0) |= PGMAX */ |
| stwbrx r3,0,r5 |
| lwbrx r4,0,r6 /* old MCCR1 */ |
| oris r4,r4,0x0008 /* MEMGO=1 */ |
| stwbrx r4, 0, r6 |
| |
| /* Wait again */ |
| |
| addis r4,r0,0x0002 |
| ori r4,r4,0xffff |
| |
| mtctr r4 |
| |
| KahluaX4wait8ref: |
| bdnz KahluaX4wait8ref |
| |
| sync |
| eieio |
| mtlr r11 |
| blr |
| |
| #else /* USE_V2_INIT */ |
| |
| |
| |
| /* U-Boot works, but memory will not run reliably for all address ranges. |
| * Early U-Boot Working init, but 2.4.19 kernel will crash since memory is not |
| * initialized correctly. Could work if debugged. |
| */ |
| /* PCI Support routines */ |
| |
| .globl __pci_config_read_32 |
| __pci_config_read_32: |
| lis r4, 0xfec0 |
| stwbrx r3, r0, r4 |
| sync |
| lis r4, 0xfee0 |
| lwbrx r3, 0, r4 |
| blr |
| .globl __pci_config_read_16 |
| __pci_config_read_16: |
| lis r4, 0xfec0 |
| andi. r5, r3, 2 |
| stwbrx r3, r0, r4 |
| sync |
| oris r4, r5, 0xfee0 |
| lhbrx r3, r0, r4 |
| blr |
| .globl __pci_config_read_8 |
| __pci_config_read_8: |
| lis r4, 0xfec0 |
| andi. r5, r3, 3 |
| stwbrx r3, r0, r4 |
| sync |
| oris r4, r5, 0xfee0 |
| lbz r3, 0(4) |
| blr |
| .globl __pci_config_write_32 |
| __pci_config_write_32: |
| lis r5, 0xfec0 |
| stwbrx r3, r0, r5 |
| sync |
| lis r5, 0xfee0 |
| stwbrx r4, r0, r5 |
| sync |
| blr |
| .globl __pci_config_write_16 |
| __pci_config_write_16: |
| lis r5, 0xfec0 |
| andi. r6, r3, 2 |
| stwbrx r3, r0, 5 |
| sync |
| oris r5, r6, 0xfee0 |
| sthbrx r4, r0, r5 |
| sync |
| blr |
| .globl __pci_config_write_8 |
| __pci_config_write_8: |
| lis r5, 0xfec0 |
| andi. r6, r3, 3 |
| stwbrx r3, r0, r5 |
| sync |
| oris r5, r6, 0xfee0 |
| stb r4, 0(r5) |
| sync |
| blr |
| .globl in_8 |
| in_8: |
| oris r3, r3, 0xfe00 |
| lbz r3,0(r3) |
| blr |
| .globl in_16 |
| in_16: |
| oris r3, r3, 0xfe00 |
| lhbrx r3, 0, r3 |
| blr |
| .globl in_16_ne |
| in_16_ne: |
| oris r3, r3, 0xfe00 |
| lhzx r3, 0, r3 |
| blr |
| .globl in_32 |
| in_32: |
| oris r3, r3, 0xfe00 |
| lwbrx r3, 0, r3 |
| blr |
| .globl out_8 |
| out_8: |
| oris r3, r3, 0xfe00 |
| stb r4, 0(r3) |
| eieio |
| blr |
| .globl out_16 |
| out_16: |
| oris r3, r3, 0xfe00 |
| sthbrx r4, 0, r3 |
| eieio |
| blr |
| .globl out_16_ne |
| out_16_ne: |
| oris r3, r3, 0xfe00 |
| sth r4, 0(r3) |
| eieio |
| blr |
| .globl out_32 |
| out_32: |
| oris r3, r3, 0xfe00 |
| stwbrx r4, 0, r3 |
| eieio |
| blr |
| .globl read_8 |
| read_8: |
| lbz r3,0(r3) |
| blr |
| .globl read_16 |
| read_16: |
| lhbrx r3, 0, r3 |
| blr |
| .globl read_32 |
| read_32: |
| lwbrx r3, 0, r3 |
| blr |
| .globl read_32_ne |
| read_32_ne: |
| lwz r3, 0(r3) |
| blr |
| .globl write_8 |
| write_8: |
| stb r4, 0(r3) |
| eieio |
| blr |
| .globl write_16 |
| write_16: |
| sthbrx r4, 0, r3 |
| eieio |
| blr |
| .globl write_32 |
| write_32: |
| stwbrx r4, 0, r3 |
| eieio |
| blr |
| .globl write_32_ne |
| write_32_ne: |
| stw r4, 0(r3) |
| eieio |
| blr |
| |
| |
| .globl early_init_f |
| |
| early_init_f: |
| mflr r11 |
| lis r10, 0x8000 |
| |
| /* PCI Latency Timer */ |
| li r4, 0x0d |
| ori r3, r10, PLTR@l |
| bl __pci_config_write_8 |
| |
| /* Cache Line Size */ |
| li r4, 0x08 |
| ori r3, r10, PCLSR@l |
| bl __pci_config_write_8 |
| |
| /* PCI Cmd */ |
| li r4, 6 |
| ori r3, r10, PCICR@l |
| bl __pci_config_write_16 |
| |
| #if 1 |
| /* PCI Stat */ |
| ori r3, r10, PCISR@l |
| bl __pci_config_read_16 |
| ori r4, r4, 0xffff |
| ori r3, r10, PCISR@l |
| bl __pci_config_write_16 |
| #endif |
| |
| /* PICR1 */ |
| lis r4, 0xff14 |
| ori r4, r4, 0x1b98 |
| ori r3, r10, PICR1@l |
| bl __pci_config_write_32 |
| |
| |
| /* PICR2 */ |
| lis r4, 0x0404 |
| ori r4, r4, 0x0004 |
| ori r3, r10, PICR2@l |
| bl __pci_config_write_32 |
| |
| /* MIOCR1 */ |
| li r4, 0x04 |
| ori r3, r10, MIOCR1@l |
| bl __pci_config_write_8 |
| |
| /* For the MPC8245, set register 77 to %00100000 (see Errata #15) */ |
| /* SDRAM_CLK_DEL (0x77)*/ |
| li r4, 0x10 |
| ori r3, r10, MIOCR2@l |
| bl __pci_config_write_8 |
| |
| /* EUMBBAR */ |
| lis r4, 0xfc00 |
| ori r3, r10, EUMBBAR@l |
| bl __pci_config_write_32 |
| |
| /* AMBOR */ |
| |
| /* Even if Address Map B is not being used (though it should), |
| * the memory DLL needs to be cleared/set/cleared before using memory. |
| */ |
| |
| ori r3, r10, AMBOR@l |
| bl __pci_config_read_8 /* get Current bits */ |
| |
| andi. r4, r4, 0xffdf |
| ori r3, r10, AMBOR@l |
| bl __pci_config_write_16 /* Clear DLL_RESET */ |
| |
| ori r4, r4, 0x0020 |
| ori r3, r10, AMBOR@l |
| bl __pci_config_write_16 /* Set DLL_RESET */ |
| |
| andi. r4, r4, 0xffdf |
| ori r3, r10, AMBOR@l |
| bl __pci_config_write_16 /* Clear DLL_RESET */ |
| |
| /* ERCR1 */ |
| lis r4, 0x8040 /* Enable RCS2, use supplied timings */ |
| ori r4, r4, 0x8000 |
| ori r3, r10, ERCR1@l |
| bl __pci_config_write_32 |
| |
| /* ERCR2 */ |
| lis r4, 0x0000 /* Disable RCS3 parms */ |
| ori r4, r4, 0x0000 |
| ori r3, r10, ERCR2@l |
| bl __pci_config_write_32 |
| |
| /* ERCR3 */ |
| lis r4, 0x0000 /* RCS3 at 0x70000000, 64K bytes */ |
| ori r4, r4, 0x0004 |
| ori r3, r10, ERCR2@l |
| bl __pci_config_write_32 |
| |
| /* Preserve memgo bit */ |
| /* MCCR1 */ |
| |
| /* lis r4, 0x75a8 / Safe Local ROM = 11+3 clocks */ |
| lis r4, 0x75a0 /* Safe Local ROM = 11+3 clocks */ |
| /* lis r4, 0x73a0 / Fast Local ROM = 7+3 clocks */ |
| /* oris r4, r4, 0x0010 / Burst ROM/Flash enable */ |
| /* oris r4, r4, 0x0004 / Self-refresh enable */ |
| |
| /* ori r4,r4,0xFFFF / 16Mbit 2bank SDRAM */ |
| /* ori r4,r4,0xAAAA / 256Mbit 4bank SDRAM (8245 only) */ |
| /* ori r4,r4,0x5555 / 64Mbit 2bank SDRAM */ |
| ori r4,r4,0x0000 /* 64Mbit 4bank SDRAM */ |
| |
| ori r3, r10, MCCR1@l |
| bl __pci_config_write_32 |
| |
| /* MCCR2 */ |
| |
| lis r4,0x0000 |
| /* oris r4,r4,0x4000 / TS_WAIT_TIMER = 3 clocks */ |
| oris r4,r4,0x1000 /* ASRISE = 8 clocks */ |
| oris r4,r4,0x0080 /* ASFALL = 8 clocks */ |
| /* oris r4,r4,0x0010 / SDRAM Parity (else ECC) */ |
| /* oris r4,r4,0x0008 / Write parity check */ |
| /* oris r4,r4,0x0004 / SDRAM inline reads */ |
| |
| |
| /* Select a refresh rate; it needs to match the bus speed; if too */ |
| /* slow, data may be lost; if too fast, performance is lost. We */ |
| /* use the fastest value so we run at all speeds. */ |
| /* Refresh = (15600ns/busclk) - (213 (see UM)). */ |
| |
| /* ori r4,r4,0x1d2c / 133 MHz mem bus = 1867 */ |
| /* ori r4,r4,0x150c / 100 MHz mem bus = 1347 */ |
| /* ori r4,r4,0x10fc / 83 MHz mem bus = 1087 */ |
| /* ori r4,r4,0x0cc4 / 66 MHz mem bus = 817 */ |
| ori r4,r4,0x04cc /* 33 MHz mem bus (SAFE) = 307 */ |
| /* ori r4,r4,0x0002 / Reserve a page */ |
| /* ori r4,r4,0x0001 / RWM parity */ |
| |
| ori r3, r10, MCCR2@l |
| bl __pci_config_write_32 |
| |
| |
| /* MCCR3 */ |
| lis r4,0x0000 /* BSTOPRE_M = 7 (see A/N) */ |
| oris r4,r4,0x0500 /* REFREC = 8 clocks */ |
| ori r3, r10, MCCR3@l |
| bl __pci_config_write_32 |
| |
| /* MCCR4 */ /* Turn on registered buffer mode */ |
| lis r4, 0x2000 /* PRETOACT = 3 clocks */ |
| oris r4,r4,0x0400 /* ACTOPRE = 5 clocks */ |
| /* oris r4,r4,0x0080 / Enable 8-beat burst (32-bit bus) */ |
| /* oris r4,r4,0x0040 / Enable Inline ECC/Parity */ |
| oris r4,r4,0x0020 /* EXTROM enabled */ |
| oris r4,r4,0x0010 /* Registered buffers */ |
| /* oris r4,r4,0x0000 / BSTOPRE_U = 0 (see A/N) */ |
| oris r4,r4,0x0002 /* DBUS_SIZ[2] (8 bit on RCS1) */ |
| |
| /* ori r4,r4,0x8000 / Registered DIMMs */ |
| ori r4,r4,0x2000 /*CAS Latency (CL=3) (see RDLAT) */ |
| /* ori r4,r4,0x2000 / CAS Latency (CL=2) (see RDLAT) */ |
| /* ori r4,r4,0x0300 / Sequential wrap/8-beat burst */ |
| ori r4,r4,0x0200 /* Sequential wrap/4-beat burst */ |
| ori r4,r4,0x0030 /* ACTORW = 3 clocks */ |
| ori r4,r4,0x0009 /* BSTOPRE_L = 9 (see A/N) */ |
| |
| ori r3, r10, MCCR4@l |
| bl __pci_config_write_32 |
| |
| /* MSAR1 */ |
| lis r4, 0xc0804000@h |
| ori r4, r4, 0xc0804000@l |
| ori r3, r10, MSAR1@l |
| bl __pci_config_write_32 |
| |
| /* MSAR2 */ |
| lis r4, 0xc0804000@h |
| ori r4, r4, 0xc0804000@l |
| ori r3, r10, MSAR2@l |
| bl __pci_config_write_32 |
| |
| /* MESAR1 */ |
| lis r4, 0x00000000@h |
| ori r4, r4, 0x00000000@l |
| ori r3, r10, EMSAR1@l |
| bl __pci_config_write_32 |
| |
| /* MESAR2 */ |
| lis r4, 0x01010101@h |
| ori r4, r4, 0x01010101@l |
| ori r3, r10, EMSAR2@l |
| bl __pci_config_write_32 |
| |
| /* MEAR1 */ |
| lis r4, 0xffbf7f3f@h |
| ori r4, r4, 0xffbf7f3f@l |
| ori r3, r10, MEAR1@l |
| bl __pci_config_write_32 |
| |
| /* MEAR2 */ |
| lis r4, 0xffbf7f3f@h |
| ori r4, r4, 0xffbf7f3f@l |
| ori r3, r10, MEAR2@l |
| bl __pci_config_write_32 |
| |
| /* MEEAR1 */ |
| lis r4, 0x00000000@h |
| ori r4, r4, 0x00000000@l |
| ori r3, r10, EMEAR1@l |
| bl __pci_config_write_32 |
| |
| /* MEEAR2 */ |
| lis r4, 0x01010101@h |
| ori r4, r4, 0x01010101@l |
| ori r3, r10, EMEAR2@l |
| bl __pci_config_write_32 |
| |
| /* ODCR */ |
| li r4, 0x7f |
| ori r3, r10, ODCR@l |
| bl __pci_config_write_8 |
| |
| /* MBER */ |
| li r4, 0x01 |
| ori r3, r10, MBER@l |
| bl __pci_config_write_8 |
| |
| /* Page CTR aka PGMAX */ |
| li r4, 0x32 |
| ori r3, r10, 0x70 |
| bl __pci_config_write_8 |
| |
| #if 0 |
| /* CLK Drive */ |
| ori r4, r10, 0xfc01 /* Top bit will be ignored */ |
| ori r3, r10, 0x74 |
| bl __pci_config_write_16 |
| #endif |
| |
| /* delay */ |
| lis r7, 1 |
| mtctr r7 |
| label1: bdnz label1 |
| |
| /* Set memgo bit */ |
| /* MCCR1 */ |
| ori r3, r10, MCCR1@l |
| bl __pci_config_read_32 |
| lis r7, 0x0008 |
| or r4, r3, r7 |
| ori r3, r10, MCCR1@l |
| bl __pci_config_write_32 |
| |
| /* delay again */ |
| lis r7, 1 |
| mtctr r7 |
| label2: bdnz label2 |
| #if 0 |
| /* DEBUG: Infinite loop, write then read */ |
| loop: |
| lis r7, 0xffff |
| mtctr r7 |
| li r3, 0x5004 |
| lis r4, 0xa0a0 |
| ori r4, r4, 0x5050 |
| bl write_32_ne |
| li r3, 0x5004 |
| bl read_32_ne |
| bdnz loop |
| #endif |
| mtlr r11 |
| blr |
| #endif |
| |