| /* |
| * (C) Copyright 2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /************************************************************************ |
| * kilauea.h - configuration for AMCC Kilauea (405EX) |
| ***********************************************************************/ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_KILAUEA 1 /* Board is Kilauea */ |
| #define CONFIG_4xx 1 /* ... PPC4xx family */ |
| #define CONFIG_405EX 1 /* Specifc 405EX support*/ |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ |
| #define CONFIG_BOARD_EMAC_COUNT |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_FLASH_BASE 0xFC000000 |
| #define CFG_NAND_ADDR 0xF8000000 |
| #define CFG_FPGA_BASE 0xF0000000 |
| #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ |
| #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ |
| #define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ |
| #define CFG_MONITOR_BASE (TEXT_BASE) |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & stack pointer |
| *----------------------------------------------------------------------*/ |
| #define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */ |
| #define CFG_INIT_RAM_END (4 << 10) |
| #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| /* reserve some memory for POST and BOOT limit info */ |
| #define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) |
| |
| /* extra data in init-ram */ |
| #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) |
| #define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8) |
| #define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12) |
| #define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */ |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SERIAL_MULTI 1 |
| /* define this if you want console on UART1 */ |
| #undef CONFIG_UART1_CONSOLE |
| |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| /*----------------------------------------------------------------------- |
| * Environment |
| *----------------------------------------------------------------------*/ |
| #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) |
| #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #else |
| #define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ |
| #define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * FLASH related |
| *----------------------------------------------------------------------*/ |
| #define CFG_FLASH_CFI /* The flash is CFI compatible */ |
| #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| |
| #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| #ifdef CFG_ENV_IS_IN_FLASH |
| #define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) |
| #endif /* CFG_ENV_IS_IN_FLASH */ |
| |
| /* |
| * IPL (Initial Program Loader, integrated inside CPU) |
| * Will load first 4k from NAND (SPL) into cache and execute it from there. |
| * |
| * SPL (Secondary Program Loader) |
| * Will load special U-Boot version (NUB) from NAND and execute it. This SPL |
| * has to fit into 4kByte. It sets up the CPU and configures the SDRAM |
| * controller and the NAND controller so that the special U-Boot image can be |
| * loaded from NAND to SDRAM. |
| * |
| * NUB (NAND U-Boot) |
| * This NAND U-Boot (NUB) is a special U-Boot version which can be started |
| * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. |
| * |
| * On 440EPx the SPL is copied to SDRAM before the NAND controller is |
| * set up. While still running from cache, I experienced problems accessing |
| * the NAND controller. sr - 2006-08-25 |
| */ |
| #define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ |
| #define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ |
| #define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ |
| #define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ |
| #define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ |
| #define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) |
| |
| /* |
| * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) |
| */ |
| #define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ |
| #define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ |
| |
| /* |
| * Now the NAND chip has to be defined (no autodetection used!) |
| */ |
| #define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ |
| #define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ |
| #define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ |
| #define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ |
| #define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ |
| |
| #define CFG_NAND_ECCSIZE 256 |
| #define CFG_NAND_ECCBYTES 3 |
| #define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) |
| #define CFG_NAND_OOBSIZE 16 |
| #define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) |
| #define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} |
| |
| #ifdef CFG_ENV_IS_IN_NAND |
| /* |
| * For NAND booting the environment is embedded in the U-Boot image. Please take |
| * look at the file board/amcc/sequoia/u-boot-nand.lds for details. |
| */ |
| #define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE |
| #define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) |
| #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * NAND FLASH |
| *----------------------------------------------------------------------*/ |
| #define CFG_MAX_NAND_DEVICE 1 |
| #define NAND_MAX_CHIPS 1 |
| #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) |
| #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------*/ |
| #define CFG_MBYTES_SDRAM (256) /* 256MB */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ |
| #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ |
| #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| |
| /* Standard DTT sensor configuration */ |
| #define CONFIG_DTT_DS1775 1 |
| #define CONFIG_DTT_SENSORS { 0 } |
| #define CFG_I2C_DTT_ADDR 0x48 |
| |
| /* RTC configuration */ |
| #define CONFIG_RTC_DS1338 1 |
| #define CFG_I2C_RTC_ADDR 0x68 |
| |
| /*----------------------------------------------------------------------- |
| * Ethernet |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_M88E1111_PHY 1 |
| #define CONFIG_IBM_EMAC4_V4 1 |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ |
| |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| #define CONFIG_HAS_ETH0 1 |
| |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ |
| #define CONFIG_PHY1_ADDR 2 |
| |
| #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "logversion=2\0" \ |
| "netdev=eth0\0" \ |
| "hostname=kilauea\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ |
| "net_nfs=tftp 200000 ${bootfile};" \ |
| "run nfsargs addip addtty;" \ |
| "bootm 200000\0" \ |
| "net_nfs_fdt=tftp 200000 ${bootfile};" \ |
| "tftp ${fdt_addr} ${fdt_file};" \ |
| "run nfsargs addip addtty;" \ |
| "bootm 200000 - ${fdt_addr}\0" \ |
| "flash_nfs=run nfsargs addip addtty;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip addtty;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "rootpath=/opt/eldk/ppc_4xx\0" \ |
| "bootfile=kilauea/uImage\0" \ |
| "fdt_file=kilauea/kilauea.dtb\0" \ |
| "fdt_addr=400000\0" \ |
| "kernel_addr=fc000000\0" \ |
| "ramdisk_addr=fc200000\0" \ |
| "initrd_high=30000000\0" \ |
| "load=tftp 200000 kilauea/u-boot.bin\0" \ |
| "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ |
| "cp.b ${fileaddr} fffa0000 ${filesize};" \ |
| "setenv filesize;saveenv\0" \ |
| "upd=run load update\0" \ |
| "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ |
| "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ |
| "setenv filesize;saveenv\0" \ |
| "nupd=run nload nupdate\0" \ |
| "pciconfighost=1\0" \ |
| "pcie_mode=RP:RP\0" \ |
| "" |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_DIAG |
| #define CONFIG_CMD_DTT |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_LOG |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_SNTP |
| |
| /* POST support */ |
| #define CONFIG_POST (CFG_POST_MEMORY | \ |
| CFG_POST_CACHE | \ |
| CFG_POST_CPU | \ |
| CFG_POST_ETHER | \ |
| CFG_POST_I2C | \ |
| CFG_POST_MEMORY | \ |
| CFG_POST_UART) |
| |
| /* Define here the base-addresses of the UARTs to test in POST */ |
| #define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE} |
| |
| #define CONFIG_LOGBUFFER |
| #define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ |
| |
| #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /*----------------------------------------------------------------------- |
| * Miscellaneous configurable options |
| *----------------------------------------------------------------------*/ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_LOOPW 1 /* enable loopw command */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| #define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE |
| |
| /*----------------------------------------------------------------------- |
| * PCIe stuff |
| *----------------------------------------------------------------------*/ |
| #define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ |
| #define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ |
| |
| #define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */ |
| #define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */ |
| #define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ |
| |
| #define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */ |
| #define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */ |
| #define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ |
| |
| #define CFG_PCIE0_UTLBASE 0xef502000 |
| #define CFG_PCIE1_UTLBASE 0xef503000 |
| |
| /* base address of inbound PCIe window */ |
| #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| *----------------------------------------------------------------------*/ |
| #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) |
| /* booting from NAND, so NAND chips select has to be on CS 0 */ |
| #define CFG_NAND_CS 0 /* NAND chip connected to CSx */ |
| |
| /* Memory Bank 1 (NOR-FLASH) initialization */ |
| #define CFG_EBC_PB1AP 0x05806500 |
| #define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ |
| |
| /* Memory Bank 0 (NAND-FLASH) initialization */ |
| #define CFG_EBC_PB0AP 0x018003c0 |
| #define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000) |
| #else |
| #define CFG_NAND_CS 1 /* NAND chip connected to CSx */ |
| |
| /* Memory Bank 0 (NOR-FLASH) initialization */ |
| #define CFG_EBC_PB0AP 0x05806500 |
| #define CFG_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ |
| |
| /* Memory Bank 1 (NAND-FLASH) initialization */ |
| #define CFG_EBC_PB1AP 0x018003c0 |
| #define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000) |
| #endif |
| |
| /* Memory Bank 2 (FPGA) initialization */ |
| #define CFG_EBC_PB2AP 0x9400C800 |
| #define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */ |
| |
| #define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ |
| |
| /*----------------------------------------------------------------------- |
| * GPIO Setup |
| *----------------------------------------------------------------------*/ |
| #define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ |
| {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ |
| } \ |
| } |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Some Kilauea stuff..., mainly fpga registers |
| */ |
| #define CFG_FPGA_REG_BASE CFG_FPGA_BASE |
| #define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 11)) |
| |
| /* interrupt */ |
| #define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000 |
| #define CFG_FPGA_SLIC0_W_DPRAM_INT 0x40000000 |
| #define CFG_FPGA_SLIC1_R_DPRAM_INT 0x20000000 |
| #define CFG_FPGA_SLIC1_W_DPRAM_INT 0x10000000 |
| #define CFG_FPGA_PHY0_INT 0x08000000 |
| #define CFG_FPGA_PHY1_INT 0x04000000 |
| #define CFG_FPGA_SLIC0_INT 0x02000000 |
| #define CFG_FPGA_SLIC1_INT 0x01000000 |
| |
| /* DPRAM setting */ |
| /* 00: 32B; 01: 64B; 10: 128B; 11: 256B */ |
| #define CFG_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */ |
| #define CFG_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */ |
| #define CFG_FPGA_DPRAM_RW_TYPE 0x00080000 |
| #define CFG_FPGA_DPRAM_RST 0x00040000 |
| #define CFG_FPGA_UART0_FO 0x00020000 |
| #define CFG_FPGA_UART1_FO 0x00010000 |
| |
| /* loopback */ |
| #define CFG_FPGA_CHIPSIDE_LOOPBACK 0x00004000 |
| #define CFG_FPGA_LINESIDE_LOOPBACK 0x00008000 |
| #define CFG_FPGA_SLIC0_ENABLE 0x00002000 |
| #define CFG_FPGA_SLIC1_ENABLE 0x00001000 |
| #define CFG_FPGA_SLIC0_CS 0x00000800 |
| #define CFG_FPGA_SLIC1_CS 0x00000400 |
| #define CFG_FPGA_USER_LED0 0x00000200 |
| #define CFG_FPGA_USER_LED1 0x00000100 |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| |
| #define OF_CPU "PowerPC,405EX@0" |
| |
| #endif /* __CONFIG_H */ |