blob: 2dbb5f70a98979dfdcaf3adfd90d8c8a871b6dea [file] [log] [blame]
/*
* Copyright (C) 2014 Freescale Semiconductor
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LSCH3
#define CONFIG_LS2085A
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
/* Errata fixes */
#define CONFIG_ARM_ERRATA_828024
#define CONFIG_ARM_ERRATA_826974
#include <asm/arch-fsl-lsch3/ls2085a_stream_id.h>
#include <asm/arch-fsl-lsch3/config.h>
#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
#define CONFIG_SYS_HAS_SERDES
#endif
/* We need architecture specific misc initializations */
#define CONFIG_ARCH_MISC_INIT
/* Link Definitions */
#ifdef CONFIG_SPL
#define CONFIG_SYS_TEXT_BASE 0x80400000
#else
#define CONFIG_SYS_TEXT_BASE 0x30100000
#endif
#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
#endif
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F 1
/* Flat Device Tree Definitions */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#endif
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_func
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
/*
* DDR controller use 0 as the base address for binding.
* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
*/
#define CONFIG_SYS_DP_DDR_BASE_PHY 0
#define CONFIG_DP_DDR_CTRL 2
#define CONFIG_DP_DDR_NUM_CTRLS 1
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
/* I2C */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* IFC */
#define CONFIG_FSL_IFC
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
* and FPGA. This region is divided as below:
* 0x30000000 - 0x37ffffff : 128MB : NOR flash
* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
*
* To accommodate bigger NOR flash and other devices, we will map IFC
* chip selects to as below:
* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
*
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
*/
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#endif
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define QIXIS_BASE get_qixis_addr()
#define QIXIS_BASE_PHYS 0x20000000
#define QIXIS_BASE_PHYS_EARLY 0xC000000
#define QIXIS_STAT_PRES1 0xb
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* Debug Server firmware */
#define CONFIG_FSL_DEBUG_SERVER
/* 2 sec timeout */
#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT (2 * 1000 * 1000)
/* MC firmware */
#define CONFIG_FSL_MC_ENET
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
#define CONFIG_SYS_MEM_TOP_HIDE_MIN (512UL * 1024 * 1024)
#define CONFIG_SYS_MEM_TOP_HIDE get_dram_size_to_hide()
#endif
/* PCIe */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE2 /* PCIE controler 2 */
#define CONFIG_PCIE3 /* PCIE controler 3 */
#define CONFIG_PCIE4 /* PCIE controler 4 */
#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
#define FSL_PCIE_COMPAT "fsl,ls2085a-pcie"
#define CONFIG_SYS_PCI_64BIT
#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
/* Command line configuration */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_ARCH_EARLY_INIT_R
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_NR_DRAM_BANKS 3
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#define CONFIG_DISPLAY_CPUINFO
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581200000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0"
#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
"earlycon=uart8250,mmio,0x21c0500,115200 " \
"ramdisk_size=0x2000000 default_hugepagesz=2m" \
" hugepagesz=2m hugepages=16"
#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
"$kernel_size && bootm $kernel_load"
#define CONFIG_BOOTDELAY 10
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#ifndef __ASSEMBLY__
unsigned long get_dram_size_to_hide(void);
#endif
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE 0x1800a000
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif /* __LS2_COMMON_H */