blob: f77e63c22f8add93fb5ab00db5eab536080dd9d1 [file] [log] [blame]
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* Corenet DS style board configuration file
*/
#ifndef __T4QDS_H
#define __T4QDS_H
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_CMD_REGINFO
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_MP /* support multiple processors */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff40000
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
#define CONFIG_FSL_IFC /* Enable IFC Support */
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controler 1 */
#define CONFIG_PCIE2 /* PCIE controler 2 */
#define CONFIG_PCIE3 /* PCIE controler 3 */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
#define CONFIG_SRIO2 /* SRIO port 2 */
#define CONFIG_FSL_LAW /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB /* toggle branch predition */
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#endif
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_ADDR_MAP
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
#define CONFIG_SYS_L3_SIZE (512 << 10)
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
#endif
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10)
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
/*
* IFC Definitions
*/
#define CONFIG_SYS_FLASH_BASE 0xe0000000
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_MISC_INIT_R
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
/*
* RapidIO
*/
#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
/* controller 4, Base address 203000 */
#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
/* SATA */
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#endif
#ifdef CONFIG_FMAN_ENET
#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC1"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
/*
* Environment
*/
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Command line configuration.
*/
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#ifdef CONFIG_PCI
#define CONFIG_CMD_PCI
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
/*
* Environment Configuration
*/
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BAUDRATE 115200
#define CONFIG_HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
"bootm 0x01000000 - 0x00f00000"
#endif /* __CONFIG_H */