| /** |
| * @file IxI2cDrv.h |
| * |
| * @brief Header file for the IXP400 I2C Driver (IxI2cDrv) |
| * |
| * @version $Revision: 0.1 $ |
| * |
| * @par |
| * IXP400 SW Release version 2.0 |
| * |
| * -- Copyright Notice -- |
| * |
| * @par |
| * Copyright 2001-2005, Intel Corporation. |
| * All rights reserved. |
| * |
| * @par |
| * SPDX-License-Identifier: BSD-3-Clause |
| * @par |
| * -- End of Copyright Notice -- |
| */ |
| |
| /** |
| * @defgroup IxI2cDrv IXP400 I2C Driver(IxI2cDrv) API |
| * |
| * @brief IXP400 I2C Driver Public API |
| * |
| * @{ |
| */ |
| #ifndef IXI2CDRV_H |
| #define IXI2CDRV_H |
| |
| #ifdef __ixp46X |
| #include "IxOsal.h" |
| |
| /* |
| * Section for #define |
| */ |
| |
| /** |
| * @ingroup IxI2cDrv |
| * @brief The interval of micro/mili seconds the IXP will wait before it polls for |
| * status from the ixI2cIntrXferStatus; Every 20us is 1 byte @ |
| * 400Kbps and 4 bytes @ 100Kbps. This is dependent on delay type selected |
| * through the API ixI2cDrvDelayTypeSelect. |
| */ |
| #define IX_I2C_US_POLL_FOR_XFER_STATUS 20 |
| |
| /** |
| * @ingroup IxI2cDrv |
| * @brief The number of tries that will be attempted to call a callback |
| * function if the callback does not or is unable to resolve the |
| * issue it is called to resolve |
| */ |
| #define IX_I2C_NUM_OF_TRIES_TO_CALL_CALLBACK_FUNC 10 |
| |
| |
| /** |
| * @ingroup IxI2cDrv |
| * @brief Number of tries slave will poll the IDBR Rx full bit before it |
| * gives up |
| */ |
| #define IX_I2C_NUM_TO_POLL_IDBR_RX_FULL 0x100 |
| |
| /** |
| * @ingroup IxI2cDrv |
| * @brief Number of tries slave will poll the IDBR Tx empty bit before it |
| * gives up |
| */ |
| #define IX_I2C_NUM_TO_POLL_IDBR_TX_EMPTY 0x100 |
| |
| /* |
| * Section for enum |
| */ |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IxI2cMasterStatus |
| * |
| * @brief The master status - transfer complete, bus error or arbitration loss |
| */ |
| typedef enum |
| { |
| IX_I2C_MASTER_XFER_COMPLETE = IX_SUCCESS, |
| IX_I2C_MASTER_XFER_BUS_ERROR, |
| IX_I2C_MASTER_XFER_ARB_LOSS |
| } IxI2cMasterStatus; |
| |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IX_I2C_STATUS |
| * |
| * @brief The status that can be returned in a I2C driver initialization |
| */ |
| typedef enum |
| { |
| IX_I2C_SUCCESS = IX_SUCCESS, /**< Success status */ |
| IX_I2C_FAIL, /**< Fail status */ |
| IX_I2C_NOT_SUPPORTED, /**< hardware does not have dedicated I2C hardware */ |
| IX_I2C_NULL_POINTER, /**< parameter passed in is NULL */ |
| IX_I2C_INVALID_SPEED_MODE_ENUM_VALUE, /**< speed mode selected is invalid */ |
| IX_I2C_INVALID_FLOW_MODE_ENUM_VALUE, /**< flow mode selected is invalid */ |
| IX_I2C_SLAVE_ADDR_CB_MISSING, /**< slave callback is NULL */ |
| IX_I2C_GEN_CALL_CB_MISSING, /**< general callback is NULL */ |
| IX_I2C_INVALID_SLAVE_ADDR, /**< invalid slave address specified */ |
| IX_I2C_INT_BIND_FAIL, /**< interrupt bind fail */ |
| IX_I2C_INT_UNBIND_FAIL, /**< interrupt unbind fail */ |
| IX_I2C_NOT_INIT, /**< I2C is not initialized yet */ |
| IX_I2C_MASTER_BUS_BUSY, /**< master detected a I2C bus busy */ |
| IX_I2C_MASTER_ARB_LOSS, /**< master experienced arbitration loss */ |
| IX_I2C_MASTER_XFER_ERROR, /**< master experienced a transfer error */ |
| IX_I2C_MASTER_BUS_ERROR, /**< master detected a I2C bus error */ |
| IX_I2C_MASTER_NO_BUFFER, /**< no buffer provided for master transfer */ |
| IX_I2C_MASTER_INVALID_XFER_MODE, /**< xfer mode selected is invalid */ |
| IX_I2C_SLAVE_ADDR_NOT_DETECTED, /**< polled slave addr not detected */ |
| IX_I2C_GEN_CALL_ADDR_DETECTED, /**< polling detected general call */ |
| IX_I2C_SLAVE_READ_DETECTED, /**< polling detected slave read request */ |
| IX_I2C_SLAVE_WRITE_DETECTED, /**< polling detected slave write request */ |
| IX_I2C_SLAVE_NO_BUFFER, /**< no buffer provided for slave transfers */ |
| IX_I2C_DATA_SIZE_ZERO, /**< data size transfer is zero - invalid */ |
| IX_I2C_SLAVE_WRITE_BUFFER_EMPTY, /**< slave buffer is used till empty */ |
| IX_I2C_SLAVE_WRITE_ERROR, /**< slave write experienced an error */ |
| IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL, /**< slave buffer is filled up */ |
| IX_I2C_SLAVE_OR_GEN_READ_ERROR /**< slave read experienced an error */ |
| } IX_I2C_STATUS; |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IxI2cSpeedMode |
| * |
| * @brief Type of speed modes supported by the I2C hardware. |
| */ |
| typedef enum |
| { |
| IX_I2C_NORMAL_MODE = 0x0, |
| IX_I2C_FAST_MODE |
| } IxI2cSpeedMode; |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IxI2cXferMode |
| * |
| * @brief Used for indicating it is a repeated start or normal transfer |
| */ |
| typedef enum |
| { |
| IX_I2C_NORMAL = 0x0, |
| IX_I2C_REPEATED_START |
| } IxI2cXferMode; |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IxI2cFlowMode |
| * |
| * @brief Used for indicating it is a poll or interrupt mode |
| */ |
| typedef enum |
| { |
| IX_I2C_POLL_MODE = 0x0, |
| IX_I2C_INTERRUPT_MODE |
| } IxI2cFlowMode; |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @enum IxI2cDelayMode |
| * |
| * @brief Used for selecting looping delay or OS scheduler delay |
| */ |
| typedef enum |
| { |
| IX_I2C_LOOP_DELAY = 1, /**< delay in microseconds */ |
| IX_I2C_SCHED_DELAY /**< delay in miliseconds */ |
| } IxI2cDelayMode; |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @brief The pointer to the function that will be called when the master |
| * has completed its receive. The parameter that is passed will |
| * provide the status of the read (success, arb loss, or bus |
| * error), the transfer mode (normal or repeated start, the |
| * buffer pointer and number of bytes transferred. |
| */ |
| typedef void (*IxI2cMasterReadCallbackP)(IxI2cMasterStatus, IxI2cXferMode, char*, UINT32); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @brief The pointer to the function that will be called when the master |
| * has completed its transmit. The parameter that is passed will |
| * provide the status of the write (success, arb loss, or buss |
| * error), the transfer mode (normal or repeated start), the |
| * buffer pointer and number of bytes transferred. |
| */ |
| typedef void (*IxI2cMasterWriteCallbackP)(IxI2cMasterStatus, IxI2cXferMode, char*, UINT32); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @brief The pointer to the function that will be called when a slave |
| * address detected in interrupt mode for a read. The parameters |
| * that is passed will provide the read status, buffer pointer, |
| * buffer size, and the bytes received. When a start of a read |
| * is initiated there will be no buffer allocated and this callback |
| * will be called to request for a buffer. While receiving, if the |
| * buffer gets filled, this callback will be called to request for |
| * a new buffer while sending the filled buffer's pointer and size, |
| * and data size received. When the receive is complete, this |
| * callback will be called to process the data and free the memory |
| * by passing the buffer's pointer and size, and data size received. |
| */ |
| typedef void (*IxI2cSlaveReadCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @brief The pointer to the function that will be called when a slave |
| * address detected in interrupt mode for a write. The parameters |
| * that is passed will provide the write status, buffer pointer, |
| * buffer size, and the bytes received. When a start of a write is |
| * initiated there will be no buffer allocated and this callback |
| * will be called to request for a buffer and to fill it with data. |
| * While transmitting, if the data in the buffer empties, this |
| * callback will be called to request for more data to be filled in |
| * the same or new buffer. When the transmit is complete, this |
| * callback will be called to free the memory or other actions to |
| * be taken. |
| */ |
| typedef void (*IxI2cSlaveWriteCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @brief The pointer to the function that will be called when a general |
| * call detected in interrupt mode for a read. The parameters that |
| * is passed will provide the read status, buffer pointer, buffer |
| * size, and the bytes received. When a start of a read is |
| * initiated there will be no buffer allocated and this callback |
| * will be called to request for a buffer. While receiving, if the |
| * buffer gets filled, this callback will be called to request for |
| * a new buffer while sending the filled buffer's pointer and size, |
| * and data size received. When the receive is complete, this |
| * callback will be called to process the data and free the memory |
| * by passing the buffer's pointer and size, and data size received. |
| */ |
| typedef void (*IxI2cGenCallCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32); |
| |
| /* |
| * Section for struct |
| */ |
| |
| /** |
| * @brief contains all the variables required to initialize the I2C unit |
| * |
| * Structure to be filled and used for calling initialization |
| */ |
| typedef struct |
| { |
| IxI2cSpeedMode I2cSpeedSelect; /**<Select either normal (100kbps) |
| or fast mode (400kbps)*/ |
| IxI2cFlowMode I2cFlowSelect; /**<Select interrupt or poll mode*/ |
| IxI2cMasterReadCallbackP MasterReadCBP; |
| /**<The master read callback pointer */ |
| IxI2cMasterWriteCallbackP MasterWriteCBP; |
| /**<The master write callback pointer */ |
| IxI2cSlaveReadCallbackP SlaveReadCBP; |
| /**<The slave read callback pointer */ |
| IxI2cSlaveWriteCallbackP SlaveWriteCBP; |
| /**<The slave write callback pointer */ |
| IxI2cGenCallCallbackP GenCallCBP; |
| /**<The general call callback pointer */ |
| BOOL I2cGenCallResponseEnable; /**<Enable/disable the unit to |
| respond to generall calls.*/ |
| BOOL I2cSlaveAddrResponseEnable;/**<Enable/disable the unit to |
| respond to the slave address set in |
| ISAR*/ |
| BOOL SCLEnable; /**<Enable/disable the unit from |
| driving the SCL line during master |
| mode operation*/ |
| UINT8 I2cHWAddr; /**<The address the unit will |
| response to as a slave device*/ |
| } IxI2cInitVars; |
| |
| /** |
| * @brief contains results of counters and their overflow |
| * |
| * Structure contains all values of counters and associated overflows. |
| */ |
| typedef struct |
| { |
| UINT32 ixI2cMasterXmitCounter; /**<Total bytes transmitted as |
| master.*/ |
| UINT32 ixI2cMasterFailedXmitCounter; /**<Total bytes failed for |
| transmission as master.*/ |
| UINT32 ixI2cMasterRcvCounter; /**<Total bytes received as |
| master.*/ |
| UINT32 ixI2cMasterFailedRcvCounter; /**<Total bytes failed for |
| receival as master.*/ |
| UINT32 ixI2cSlaveXmitCounter; /**<Total bytes transmitted as |
| slave.*/ |
| UINT32 ixI2cSlaveFailedXmitCounter; /**<Total bytes failed for |
| transmission as slave.*/ |
| UINT32 ixI2cSlaveRcvCounter; /**<Total bytes received as |
| slave.*/ |
| UINT32 ixI2cSlaveFailedRcvCounter; /**<Total bytes failed for |
| receival as slave.*/ |
| UINT32 ixI2cGenAddrCallSucceedCounter; /**<Total bytes successfully |
| transmitted for general address.*/ |
| UINT32 ixI2cGenAddrCallFailedCounter; /**<Total bytes failed transmission |
| for general address.*/ |
| UINT32 ixI2cArbLossCounter; /**<Total instances of arbitration |
| loss has occured.*/ |
| } IxI2cStatsCounters; |
| |
| |
| /* |
| * Section for prototypes interface functions |
| */ |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvInit( |
| IxI2cInitVars *InitVarsSelected) |
| * |
| * @brief Initializes the I2C Driver. |
| * |
| * @param "IxI2cInitVars [in] *InitVarsSelected" - struct containing required |
| * variables for initialization |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will check if the hardware supports this I2C driver and the validity |
| * of the parameters passed in. It will continue to process the parameters |
| * passed in by setting the speed of the I2C unit (100kbps or 400kbps), setting |
| * the flow to either interrupt or poll mode, setting the address of the I2C unit, |
| * enabling/disabling the respond to General Calls, enabling/disabling the respond |
| * to Slave Address and SCL line driving. If it is interrupt mode, then it will |
| * register the callback routines for master, slavetransfer and general call receive. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - Successfully initialize and enable the I2C |
| * hardware. |
| * - IX_I2C_NOT_SUPPORTED - The hardware does not support or have a |
| * dedicated I2C unit to support this driver |
| * - IX_I2C_NULL_POINTER - The parameter passed in is a NULL pointed |
| * - IX_I2C_INVALID_SPEED_MODE_ENUM_VALUE - The speed mode selected in the |
| * InitVarsSelected is invalid |
| * - IX_I2C_INVALID_FLOW_MODE_ENUM_VALUE - The flow mode selected in the |
| * InitVarsSelected is invalid |
| * - IX_I2C_INVALID_SLAVE_ADDR - The address 0x0 is reserved for |
| * general call. |
| * - IX_I2C_SLAVE_ADDR_CB_MISSING - interrupt mode is selected but |
| * slave address callback pointer is NULL |
| * - IX_I2C_GEN_CALL_CB_MISSING - interrupt mode is selected but |
| * general call callback pointer is NULL |
| * - IX_I2C_INT_BIND_FAIL - The ISR for the I2C failed to bind |
| * - IX_I2C_INT_UNBIND_FAIL - The ISR for the I2C failed to unbind |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvInit(IxI2cInitVars *InitVarsSelected); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvUninit( |
| void) |
| * |
| * @brief Disables the I2C hardware |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will disable the I2C hardware, unbind interrupt, and unmap memory. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - successfully un-initialized I2C |
| * - IX_I2C_INT_UNBIND_FAIL - failed to unbind the I2C interrupt |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvUninit(void); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvSlaveAddrSet( |
| UINT8 SlaveAddrSet) |
| * |
| * @brief Sets the I2C Slave Address |
| * |
| * @param "UINT8 [in] SlaveAddrSet" - Slave Address to be inserted into ISAR |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will insert the SlaveAddrSet into the ISAR. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - successfuly set the slave addr |
| * - IX_I2C_INVALID_SLAVE_ADDR - invalid slave address (zero) specified |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvSlaveAddrSet(UINT8 SlaveAddrSet); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvBusScan( |
| void) |
| * |
| * @brief scans the I2C bus for slave devices |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will prompt all slave addresses for a reply except its own |
| * |
| * @return |
| * - IX_I2C_SUCCESS - found at least one slave device |
| * - IX_I2C_FAIL - Fail to find even one slave device |
| * - IX_I2C_BUS_BUSY - The I2C bus is busy (held by another I2C master) |
| * - IX_I2C_ARB_LOSS - The I2C bus was loss to another I2C master |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : yes |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvBusScan(void); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvWriteTransfer( |
| UINT8 SlaveAddr, |
| char *bufP, |
| UINT32 dataSize, |
| IxI2cXferMode XferModeSelect) |
| * |
| * @param "UINT8 [in] SlaveAddr" - The slave address to request data from. |
| * @param "char [in] *bufP" - The pointer to the data to be transmitted. |
| * @param "UINT32 [in] dataSize" - The number of bytes requested. |
| * @param "IxI2cXferMode [in] XferModeSelect" - the transfer mode selected, |
| * either repeated start (ends w/o stop) or normal (start and stop) |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will try to obtain master control of the I2C bus and transmit the |
| * number of bytes, specified by dataSize, to the user specified slave |
| * address from the buffer pointer. It will use either interrupt or poll mode |
| * depending on the method selected. |
| * |
| * If in interrupt mode and IxI2cMasterWriteCallbackP is not NULL, the driver |
| * will initiate the transfer and return immediately. The function pointed to |
| * by IxI2cMasterWriteCallbackP will be called in the interrupt service |
| * handlers when the operation is complete. |
| * |
| * If in interrupt mode and IxI2cMasterWriteCallbackP is NULL, then the driver |
| * will wait for the operation to complete, and then return. |
| * |
| * And if the repeated start transfer mode is selected, then it will not send a |
| * stop signal at the end of all the transfers. |
| * *NOTE*: If repeated start transfer mode is selected, it has to end with a |
| * normal mode transfer mode else the bus will continue to be held |
| * by the IXP. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - Successfuuly wrote data to slave. |
| * - IX_I2C_MASTER_BUS_BUSY - The I2C bus is busy (held by another I2C master) |
| * - IX_I2C_MASTER_ARB_LOSS - The I2C bus was loss to another I2C master |
| * - IX_I2C_MASTER_XFER_ERROR - There was a transfer error |
| * - IX_I2C_MASTER_BUS_ERROR - There was a bus error during transfer |
| * - IX_I2C_MASTER_NO_BUFFER - buffer pointer is NULL |
| * - IX_I2C_MASTER_INVALID_XFER_MODE - Xfer mode selected is invalid |
| * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvWriteTransfer( |
| UINT8 SlaveAddr, |
| char *bufP, |
| UINT32 dataSize, |
| IxI2cXferMode XferModeSelect); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvReadTransfer( |
| UINT8 SlaveAddr, |
| char *bufP, |
| UINT32 dataSize, |
| IxI2cXferMode XferModeSelect) |
| * |
| * @brief Initiates a transfer to receive bytes of data from a slave |
| * device through the I2C bus. |
| * |
| * @param "UINT8 [in] SlaveAddr" - The slave address to request data from. |
| * @param "char [out] *bufP" - The pointer to the buffer to store the |
| * requested data. |
| * @param "UINT32 [in] dataSize" - The number of bytes requested. |
| * @param "IxI2cXferMode [in] XferModeSelect" - the transfer mode selected, |
| * either repeated start (ends w/o stop) or normal (start and stop) |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will try to obtain master control of the I2C bus and receive the |
| * number of bytes, specified by dataSize, from the user specified address |
| * into the receive buffer. It will use either interrupt or poll mode depending |
| * on the mode selected. |
| * |
| * If in interrupt mode and IxI2cMasterReadCallbackP is not NULL, the driver |
| * will initiate the transfer and return immediately. The function pointed to |
| * by IxI2cMasterReadCallbackP will be called in the interrupt service |
| * handlers when the operation is complete. |
| * |
| * If in interrupt mode and IxI2cMasterReadCallbackP is NULL, then the driver will |
| * wait for the operation to complete, and then return. |
| * |
| * And if the repeated start transfer mode is selected, then it will not send a |
| * stop signal at the end of all the transfers. |
| * *NOTE*: If repeated start transfer mode is selected, it has to end with a |
| * normal mode transfer mode else the bus will continue to be held |
| * by the IXP. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - Successfuuly read slave data |
| * - IX_I2C_MASTER_BUS_BUSY - The I2C bus is busy (held by another I2C master) |
| * - IX_I2C_MASTER_ARB_LOSS - The I2C bus was loss to another I2C master |
| * - IX_I2C_MASTER_XFER_ERROR - There was a bus error during transfer |
| * - IX_I2C_MASTER_BUS_ERROR - There was a bus error during transfer |
| * - IX_I2C_MASTER_NO_BUFFER - buffer pointer is NULL |
| * - IX_I2C_MASTER_INVALID_XFER_MODE - Xfer mode selected is invalid |
| * - IX_I2C_INVALID_SLAVE_ADDR - invalid slave address (zero) specified |
| * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvReadTransfer( |
| UINT8 SlaveAddr, |
| char *bufP, |
| UINT32 dataSize, |
| IxI2cXferMode XferModeSelect); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvSlaveAddrAndGenCallDetectedCheck( |
| void) |
| * |
| * @brief Checks the I2C Status Register to determine if a slave address is |
| * detected |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is used in polled mode to determine if the I2C unit is requested |
| * for a slave or general call transfer. If it is requested for a slave |
| * transfer then it will determine if it is a general call (read only), read, |
| * or write transfer requested. |
| * |
| * @return |
| * - IX_I2C_SLAVE_ADDR_NOT_DETECTED - The I2C unit is not requested for slave |
| * transfer |
| * - IX_I2C_GEN_CALL_ADDR_DETECTED - The I2C unit is not requested for slave |
| * transfer but for general call |
| * - IX_I2C_SLAVE_READ_DETECTED - The I2C unit is requested for a read |
| * - IX_I2C_SLAVE_WRITE_DETECTED - The I2C unit is requested for a write |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvSlaveAddrAndGenCallDetectedCheck(void); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvSlaveOrGenDataReceive( |
| char *bufP, |
| UINT32 bufSize, |
| UINT32 *dataSizeRcvd) |
| * |
| * @brief Performs the slave receive or general call receive data transfer |
| * |
| * @param "char [in] *bufP" - the pointer to the buffer to store data |
| * "UINT32 [in] bufSize" - the buffer size allocated |
| * "UINT32 [in] *dataSizeRcvd" - the length of data received in bytes |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is only used in polled mode to perform the slave read or general call |
| * receive data. It will continuously store the data received into bufP until |
| * complete or until bufP is full in which it will return |
| * IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL. If in interrupt mode, the callback will be |
| * used. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - The I2C driver transferred the data successfully. |
| * - IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL - The I2C driver has ran out of |
| * space to store the received data. |
| * - IX_I2C_SLAVE_OR_GEN_READ_ERROR - The I2C driver didn't manage to |
| * detect the IDBR Rx Full bit |
| * - IX_I2C_DATA_SIZE_ZERO - bufSize passed in is zero, which is invalid |
| * - IX_I2C_SLAVE_NO_BUFFER - buffer pointer is NULL |
| * - IX_I2C_NULL_POINTER - dataSizeRcvd is NULL |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvSlaveOrGenDataReceive( |
| char *bufP, |
| UINT32 bufSize, |
| UINT32 *dataSizeRcvd); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvSlaveDataTransmit( |
| char *bufP, |
| UINT32 dataSize, |
| UINT32 *dataSizeXmtd) |
| * |
| * @brief Performs the slave write data transfer |
| * |
| * @param "char [in] *bufP" - the pointer to the buffer for data to be |
| * transmitted |
| * "UINT32 [in] bufSize" - the buffer size allocated |
| * "UINT32 [in] *dataSizeRcvd" - the length of data trasnmitted in |
| * bytes |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is only used in polled mode to perform the slave transmit data. It |
| * will continuously transmit the data from bufP until complete or until bufP |
| * is empty in which it will return IX_I2C_SLAVE_WRITE_BUFFER_EMPTY. If in |
| * interrupt mode, the callback will be used. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - The I2C driver transferred the data successfully. |
| * - IX_I2C_SLAVE_WRITE_BUFFER_EMPTY - The I2C driver needs more data to |
| * transmit. |
| * - IX_I2C_SLAVE_WRITE_ERROR -The I2C driver didn't manage to detect the |
| * IDBR Tx empty bit or the slave stop bit. |
| * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid |
| * - IX_I2C_SLAVE_NO_BUFFER - buffer pointer is NULL |
| * - IX_I2C_NULL_POINTER - dataSizeXmtd is NULL |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvSlaveDataTransmit( |
| char *bufP, |
| UINT32 dataSize, |
| UINT32 *dataSizeXmtd); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvSlaveOrGenCallBufReplenish( |
| char *bufP, |
| UINT32 bufSize) |
| * |
| * @brief Replenishes the buffer which stores buffer info for both slave and |
| * general call |
| * |
| * @param "char [in] *bufP" - pointer to the buffer allocated |
| * "UINT32 [in] bufSize" - size of the buffer |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API is only used in interrupt mode for replenishing the same buffer |
| * that is used by both slave and generall call by updating the buffer info |
| * with new info and clearing previous offsets set by previous transfers. |
| * |
| * @return |
| * - None |
| * |
| * @li Reentrant : no |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC void |
| ixI2cDrvSlaveOrGenCallBufReplenish( |
| char *bufP, |
| UINT32 bufSize); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvStatsGet(IxI2cStatsCounters *I2cStats) |
| * |
| * @brief Returns the I2C Statistics through the pointer passed in |
| * |
| * @param - "IxI2cStatsCounters [out] *I2cStats" - I2C statistics counter will |
| * be read and written to the location pointed by this pointer. |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will return the statistics counters of the I2C driver. |
| * |
| * @return |
| * - IX_I2C_NULL_POINTER - pointer passed in is NULL |
| * - IX_I2C_SUCCESS - successfully obtained I2C statistics |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvStatsGet(IxI2cStatsCounters *I2cStats); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvStatsReset(void) |
| * |
| * @brief Reset I2C statistics counters. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will reset the statistics counters of the I2C driver. |
| * |
| * @return |
| * - None |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC void |
| ixI2cDrvStatsReset(void); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvShow(void) |
| * |
| * @brief Displays the I2C status register and the statistics counter. |
| * |
| * @param - None |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will display the I2C Status register and is useful if any error |
| * occurs. It displays the detection of bus error, slave address, general call, |
| * address, IDBR receive full, IDBR transmit empty, arbitration loss, slave |
| * STOP signal, I2C bus busy, unit busy, ack/nack, and read/write mode. It will |
| * also call the ixI2cDrvGetStats and then display the statistics counter. |
| * |
| * @return |
| * - IX_I2C_SUCCESS - successfully displayed statistics and status register |
| * - IX_I2C_NOT_INIT - I2C not init yet. |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC IX_I2C_STATUS |
| ixI2cDrvShow(void); |
| |
| /** |
| * @ingroup IxI2cDrv |
| * |
| * @fn ixI2cDrvDelayTypeSelect (IxI2cDelayMode delayMechanismSelect) |
| * |
| * @brief Sets the delay type of either looping delay or OS scheduler delay |
| * according to the argument provided. |
| * |
| * @param - "IxI2cDelayMode [in] delayTypeSelect" - the I2C delay type selected |
| * |
| * Global Data : |
| * - None. |
| * |
| * This API will set the delay type used by the I2C Driver to either looping |
| * delay or OS scheduler delay. |
| * |
| * @return |
| * - None |
| * |
| * @li Reentrant : yes |
| * @li ISR Callable : no |
| * |
| */ |
| PUBLIC void |
| ixI2cDrvDelayTypeSelect (IxI2cDelayMode delayTypeSelect); |
| |
| #endif /* __ixp46X */ |
| #endif /* IXI2CDRV_H */ |