blob: 51fdcb7d5b19287142bc4f0e1087dad09b85c627 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2022 Gateworks Corporation
*/
#ifndef __IMX8MP_VENICE_H
#define __IMX8MP_VENICE_H
#include <asm/arch/imx-regs.h>
#include <linux/sizes.h>
#define CONFIG_SYS_MONITOR_LEN SZ_512K
#define CONFIG_SYS_UBOOT_BASE \
(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
#ifdef CONFIG_SPL_BUILD
/* For RAW image gives a error info not panic */
#endif
#define MEM_LAYOUT_ENV_SETTINGS \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"fdt_addr_r=0x50200000\0" \
"scriptaddr=0x50280000\0" \
"ramdisk_addr_r=0x50300000\0" \
"kernel_comp_addr_r=0x40200000\0"
/* Enable Distro Boot */
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 2) \
func(USB, usb, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
BOOTENV \
MEM_LAYOUT_ENV_SETTINGS \
"script=boot.scr\0" \
"bootm_size=0x10000000\0" \
"dev=2\0" \
"preboot=gsc wd-disable\0" \
"console=ttymxc1,115200\0" \
"update_firmware=" \
"tftpboot $loadaddr $image && " \
"setexpr blkcnt $filesize + 0x1ff && " \
"setexpr blkcnt $blkcnt / 0x200 && " \
"mmc dev $dev && " \
"mmc write $loadaddr 0x40 $blkcnt\0" \
"loadfdt=" \
"if $fsload $fdt_addr_r $dir/$fdt_file1; " \
"then echo loaded $fdt_file1; " \
"elif $fsload $fdt_addr_r $dir/$fdt_file2; " \
"then echo loaded $fdt_file2; " \
"elif $fsload $fdt_addr_r $dir/$fdt_file3; " \
"then echo loaded $fdt_file3; " \
"elif $fsload $fdt_addr_r $dir/$fdt_file4; " \
"then echo loaded $fdt_file4; " \
"elif $fsload $fdt_addr_r $dir/$fdt_file5; " \
"then echo loaded $fdt_file5; " \
"fi\0" \
"boot_net=" \
"setenv fsload tftpboot; " \
"run loadfdt && tftpboot $kernel_addr_r $dir/Image && " \
"booti $kernel_addr_r - $fdt_addr_r\0" \
"update_rootfs=" \
"tftpboot $loadaddr $image && " \
"gzwrite mmc $dev $loadaddr $filesize 100000 1000000\0" \
"update_all=" \
"tftpboot $loadaddr $image && " \
"gzwrite mmc $dev $loadaddr $filesize\0" \
"erase_env=mmc dev $dev; mmc erase 0x7f08 0x40\0"
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE SZ_2M
#define CONFIG_SYS_SDRAM_BASE 0x40000000
/* SDRAM configuration */
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE SZ_4G
#define CONFIG_SYS_BOOTM_LEN SZ_256M
/* FEC */
#define FEC_QUIRK_ENET_MAC
#endif