| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright 2019 Gateworks Corporation |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| /* these are used by bootloader for disabling nodes */ |
| aliases { |
| led0 = &led0; |
| led1 = &led1; |
| nand = &gpmi; |
| usb0 = &usbh1; |
| usb1 = &usbotg; |
| }; |
| |
| chosen { |
| stdout-path = &uart2; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| user-pb { |
| label = "user_pb"; |
| gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>; |
| linux,code = <BTN_0>; |
| }; |
| |
| user-pb1x { |
| label = "user_pb1x"; |
| linux,code = <BTN_1>; |
| interrupt-parent = <&gsc>; |
| interrupts = <0>; |
| }; |
| |
| key-erased { |
| label = "key-erased"; |
| linux,code = <BTN_2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <1>; |
| }; |
| |
| eeprom-wp { |
| label = "eeprom_wp"; |
| linux,code = <BTN_3>; |
| interrupt-parent = <&gsc>; |
| interrupts = <2>; |
| }; |
| |
| tamper { |
| label = "tamper"; |
| linux,code = <BTN_4>; |
| interrupt-parent = <&gsc>; |
| interrupts = <5>; |
| }; |
| |
| switch-hold { |
| label = "switch_hold"; |
| linux,code = <BTN_5>; |
| interrupt-parent = <&gsc>; |
| interrupts = <7>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_leds>; |
| |
| led0: user1 { |
| label = "user1"; |
| gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */ |
| default-state = "on"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| |
| led1: user2 { |
| label = "user2"; |
| gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */ |
| default-state = "off"; |
| }; |
| }; |
| |
| memory@10000000 { |
| device_type = "memory"; |
| reg = <0x10000000 0x20000000>; |
| }; |
| |
| pps { |
| compatible = "pps-gpio"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pps>; |
| gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| }; |
| |
| reg_3p3v: regulator-3p3v { |
| compatible = "regulator-fixed"; |
| regulator-name = "3P3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| reg_5p0v: regulator-5p0v { |
| compatible = "regulator-fixed"; |
| regulator-name = "5P0V"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet>; |
| phy-mode = "rgmii-id"; |
| phy-reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; |
| phy-reset-duration = <10>; |
| phy-reset-post-delay = <100>; |
| status = "okay"; |
| }; |
| |
| &gpmi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpmi_nand>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| gsc: gsc@20 { |
| compatible = "gw,gsc"; |
| reg = <0x20>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <4 IRQ_TYPE_LEVEL_LOW>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| #size-cells = <0>; |
| |
| adc { |
| compatible = "gw,gsc-adc"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| channel@6 { |
| gw,mode = <0>; |
| reg = <0x06>; |
| label = "temp"; |
| }; |
| |
| channel@8 { |
| gw,mode = <3>; |
| reg = <0x08>; |
| label = "vdd_bat"; |
| }; |
| |
| channel@82 { |
| gw,mode = <2>; |
| reg = <0x82>; |
| label = "vdd_vin"; |
| gw,voltage-divider-ohms = <22100 1000>; |
| gw,voltage-offset-microvolt = <800000>; |
| }; |
| |
| channel@84 { |
| gw,mode = <2>; |
| reg = <0x84>; |
| label = "vdd_5p0"; |
| gw,voltage-divider-ohms = <22100 10000>; |
| }; |
| |
| channel@86 { |
| gw,mode = <2>; |
| reg = <0x86>; |
| label = "vdd_3p3"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@88 { |
| gw,mode = <2>; |
| reg = <0x88>; |
| label = "vdd_2p5"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@8c { |
| gw,mode = <2>; |
| reg = <0x8c>; |
| label = "vdd_arm"; |
| }; |
| |
| channel@8e { |
| gw,mode = <2>; |
| reg = <0x8e>; |
| label = "vdd_soc"; |
| }; |
| |
| channel@90 { |
| gw,mode = <2>; |
| reg = <0x90>; |
| label = "vdd_1p5"; |
| }; |
| |
| channel@92 { |
| gw,mode = <2>; |
| reg = <0x92>; |
| label = "vdd_1p0"; |
| }; |
| |
| channel@98 { |
| gw,mode = <2>; |
| reg = <0x98>; |
| label = "vdd_3p0"; |
| }; |
| |
| channel@9a { |
| gw,mode = <2>; |
| reg = <0x9a>; |
| label = "vdd_an1"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| |
| channel@a2 { |
| gw,mode = <2>; |
| reg = <0xa2>; |
| label = "vdd_gsc"; |
| gw,voltage-divider-ohms = <10000 10000>; |
| }; |
| }; |
| }; |
| |
| gsc_gpio: gpio@23 { |
| compatible = "nxp,pca9555"; |
| reg = <0x23>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-parent = <&gsc>; |
| interrupts = <4>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c02"; |
| reg = <0x50>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@51 { |
| compatible = "atmel,24c02"; |
| reg = <0x51>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@52 { |
| compatible = "atmel,24c02"; |
| reg = <0x52>; |
| pagesize = <16>; |
| }; |
| |
| eeprom@53 { |
| compatible = "atmel,24c02"; |
| reg = <0x53>; |
| pagesize = <16>; |
| }; |
| |
| rtc@68 { |
| compatible = "dallas,ds1672"; |
| reg = <0x68>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| }; |
| |
| &pcie { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie>; |
| reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| }; |
| |
| &pwm2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */ |
| status = "disabled"; |
| }; |
| |
| &pwm3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */ |
| status = "disabled"; |
| }; |
| |
| &pwm4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */ |
| status = "disabled"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| status = "okay"; |
| }; |
| |
| &uart5 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart5>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| disable-over-current; |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| }; |
| |
| &iomuxc { |
| pinctrl_enet: enetgrp { |
| fsl,pins = < |
| MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030 |
| MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030 |
| MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030 |
| MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030 |
| MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 |
| MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 |
| MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030 |
| MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030 |
| MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030 |
| MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030 |
| MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030 |
| MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030 |
| MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 |
| MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 |
| MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 |
| MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 |
| MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_gpio_leds: gpioledsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 |
| MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_gpmi_nand: gpminandgrp { |
| fsl,pins = < |
| MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 |
| MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 |
| MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 |
| MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 |
| MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 |
| MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 |
| MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 |
| MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 |
| MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 |
| MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 |
| MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 |
| MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 |
| MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 |
| MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 |
| MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 |
| MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 |
| MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_pcie: pciegrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_pps: ppsgrp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm2: pwm2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm3: pwm3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_pwm4: pwm4grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_uart5: uart5grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0 |
| >; |
| }; |
| }; |