blob: f72ab0bad01c74da3b8d67a96b1b75f07d3aa7fe [file] [log] [blame]
/*
* Configuration settings for the SAMA5D3 Xplained board.
*
* Copyright (C) 2014 Atmel Corporation
* Bo Shen <voice.shen@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/hardware.h>
#define CONFIG_SYS_TEXT_BASE 0x26f00000
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#define CONFIG_ARCH_CPU_INIT
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_CMD_BOOTZ
#define CONFIG_OF_LIBFDT /* Device Tree support */
#define CONFIG_SYS_GENERIC_BOARD
/* general purpose I/O */
#define CONFIG_AT91_GPIO
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_DBGU
/*
* This needs to be defined for the OHCI code to work but it is defined as
* ATMEL_ID_UHPHS in the CPU specific header files.
*/
#define ATMEL_ID_UHP ATMEL_ID_UHPHS
/*
* Specify the clock enable bit in the PMC_SCER register.
*/
#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
#define CONFIG_BOOTDELAY 3
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* No NOR flash */
#define CONFIG_SYS_NO_FLASH
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_IMI
#undef CONFIG_CMD_LOADS
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE 0x10000000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x310000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
/* NAND flash */
#define CONFIG_CMD_NAND
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#define CONFIG_PMECC_CAP 4
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#endif
/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_MULTI
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
#define CONFIG_RGMII
#define CONFIG_CMD_MII
#define CONFIG_PHYLIB
/* MMC */
#define CONFIG_CMD_MMC
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define CONFIG_ATMEL_MCI_8BIT
#endif
/* USB */
#define CONFIG_CMD_USB
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "SAMA5D3 Xplained"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#define CONFIG_DOS_PARTITION
#define CONFIG_USB_STORAGE
#endif
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_EXT4_WRITE
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#if CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0xc0000
#define CONFIG_ENV_OFFSET_REDUND 0x100000
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0x180000 0x80000;" \
"nand read 0x22000000 0x200000 0x600000;" \
"bootz 0x22000000 - 0x21000000"
#elif CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env in sd card */
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET 0x2000
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 at91-sama5d3_xplained.dtb; " \
"fatload mmc 0:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#define CONFIG_SYS_MMC_ENV_DEV 0
#else
#define CONFIG_ENV_IS_NOWHERE
#endif
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk " \
"root=/dev/mmcblk0p2 rw rootwait"
#else
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk " \
"mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \
"256K(env),256k(evn_redundent),256k(spare)," \
"512k(dtb),6M(kernel)ro,-(rootfs) " \
"rootfstype=ubifs ubi.mtd=7 root=ubi0:rootfs"
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_PROMPT "U-Boot> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_HUSH_PARSER
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
/* SPL */
#define CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT arch/arm/cpu/at91-common/u-boot-spl.lds
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#elif CONFIG_SYS_USE_NANDFLASH
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#endif
#endif